Try to acquire the semaphore; if semaphore is hung then acquire it by force.
The ISP reset clears the semaphore, thereby implicitly releasing it.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Original code was not corrected for ISP83xx support. Instead code should used
the cached reference from the req_que structure, rather than the legacy
'if (ISP-TYPE(X))... else if (ISP-TYPE(Y))...' codes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This message can fill up the system logs and is not a common occurrence so move
it to the verbose logging level.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The value of 2 is informational message and it means that port id has
changed. The driver should honor the value and continue its normal course.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Rather than returning stale mailbox values.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the qla2xxx driver loses access to multiple, remote ports, there is a race
condition which can occur which will keep the request stuck on a scsi request
queue indefinitely.
This bad state occurred do to a race condition with how the FCPORT_UPDATE_NEEDED
bit is set in qla2x00_schedule_rport_del(), and how it is cleared in
qla2x00_do_dpc(). The problem port has its drport pointer set, but it has never
been processed by the driver to inform the fc transport that the port has been
lost. qla2x00_schedule_rport_del() sets drport, and then sets the
FCPORT_UPDATE_NEEDED bit. In qla2x00_do_dpc(), the port lists are walked and
any drport pointer is handled and the fc transport informed of the port loss,
then the FCPORT_UPDATE_NEEDED bit is cleared. This leaves a race where the
dpc thread is processing one port removal, another port removal is marked
with a call to qla2x00_schedule_rport_del(), and the dpc thread clears the
bit for both removals, even though only the first removal was actually
handled. Until another event occurs to set FCPORT_UPDATE_NEEDED, the later
port removal is never finished and qla2xxx stays in a bad state which causes
requests to become stuck on request queues.
This patch updates the driver to test and clear FCPORT_UPDATE_NEEDED
atomically. This ensures the port state changes are processed and not lost.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC transport on receiving bsg_job submission failure, calls bsg_job->job_done()
and sets the bsg_job->reply->result the returned value. In contrast, when the
success code (0) is returned fc transport doesn't call bsg_job->job_done() and
doesn't populate bsg_job->reply->result.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: <stable@vger.kernel.org> #3.7
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update sd driver to use the callbacks defined in dev_pm_ops.
sd_freeze is NULL, the bus level callback has taken care of quiescing
the device so there should be nothing needs to be done here.
Consequently, sd_thaw is not needed here either.
suspend, poweroff and runtime suspend share the same routine sd_suspend,
which will sync flush and then stop the drive, this is the same as before.
resume, restore and runtime resume share the same routine sd_resume,
which will start the drive by putting it into active power state, this
is also the same as before.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use of pm_message_t is deprecated and device driver is not supposed
to use that. This patch migrates the SCSI bus level pm callbacks
to call device's pm callbacks defined in its driver's dev_pm_ops.
This is achieved by finding out which device pm callback should be used
in bus callback function, and then pass that callback function pointer
as a param to the scsi_bus_{suspend,resume}_common routine, which will
further pass that callback to scsi_dev_type_{suspend,resume} after
proper handling.
The special case for freeze in scsi_bus_suspend_common is not necessary
since there is no high level SCSI driver has implemented freeze, so no
need to runtime resume the device if it is in runtime suspended state
for system freeze, just return like the system suspend/hibernate case.
Since only sd has implemented drv->suspend/drv->resume, and I'll update
sd driver to use the new callbacks in the following patch, there is no
need to fallback to call drv->suspend/drv->resume if dev_pm_ops is NULL.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 28fd00d42c.
With commit 88d26136a2 (PM: Prevent
runtime suspend during system resume), this patch is no longer needed.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 33a2285d96.
With commit 88d26136a2 (PM: Prevent
runtime suspend during system resume), this patch is no longer needed.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When device is runtime suspended, put it to stopped power state to save
some power.
This will also make the behaviour consistent with what the scsi_pm.c
thinks about sd as the comment says:
sd treats runtime suspend, system suspend and system hibernate identical.
With this patch, it is now identical.
And sd_shutdown will also do nothing when it finds the device has been
runtime suspended, if we do not spin down the disk in runtime suspend
by putting it into stopped power state, the disk will be shut down
incorrectly.
And the the same problem can be solved for runtime power off after
runtime suspended case by this change.
With the current runtime scheme for disk, it will only be runtime
suspended when no process opens the disk, so this shouldn't happen a
lot, which makes it acceptable to spin down the disk when runtime
suspended. If some day a more aggressive runtime scheme is used, like
the 'request based runtime pm for disk' that Alan Stern and Lin Ming
has been working, we can introduce some policy to control this. But for
now, make it simple and correct by spinning down the disk.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The macro bit(n) is defined as ((u32)1 << n), and thus it doesn't work
with n >= 32, such as in mvs_94xx_assign_reg_set():
if (i >= 32) {
mvi->sata_reg_set |= bit(i);
...
}
The shift ((u32)1 << n) with n >= 32 also leads to undefined behavior.
The result varies depending on the architecture.
This patch changes bit(n) to do a 64-bit shift. It also simplifies
mv_ffc64() using __ffs64(), since invoking ffz() with ~0 is undefined.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Xiangliang Yu <yuxiangl@marvell.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
store_host_reset() has tried to re-invent the wheel to compare sysfs strings.
Unfortunately it did so poorly and never bothered to check the input from
userspace before overwriting stack with it, so something simple as:
echo "WoopsieWoopsie" >
/sys/devices/pseudo_0/adapter0/host0/scsi_host/host0/host_reset
would result in:
[ 316.310101] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffff81f5bac7
[ 316.310101]
[ 316.320051] Pid: 6655, comm: sh Tainted: G W 3.7.0-rc5-next-20121114-sasha-00016-g5c9d68d-dirty #129
[ 316.320051] Call Trace:
[ 316.340058] pps pps0: PPS event at 1352918752.620355751
[ 316.340062] pps pps0: capture assert seq #303
[ 316.320051] [<ffffffff83b3856b>] panic+0xcd/0x1f4
[ 316.320051] [<ffffffff81f5bac7>] ? store_host_reset+0xd7/0x100
[ 316.320051] [<ffffffff8110b996>] __stack_chk_fail+0x16/0x20
[ 316.320051] [<ffffffff81f5bac7>] store_host_reset+0xd7/0x100
[ 316.320051] [<ffffffff81e55bb3>] dev_attr_store+0x13/0x30
[ 316.320051] [<ffffffff812f7db1>] sysfs_write_file+0x101/0x170
[ 316.320051] [<ffffffff8127acc8>] vfs_write+0xb8/0x180
[ 316.320051] [<ffffffff8127ae80>] sys_write+0x50/0xa0
[ 316.320051] [<ffffffff83c03418>] tracesys+0xe1/0xe6
Fix this by uninventing whatever was going on there and just use sysfs_streq.
Bug introduced by 29443691 ("[SCSI] scsi: Added support for adapter and
firmware reset").
[jejb: added necessary const to prevent compile warnings]
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: <stable@vger.kernel.org> #3.2+
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Search through the list of pending commands on the session list to find
the command the initiator is actually aborting, so that we can pass the
correct LUN to the core TMR handling code.
(nab: Allow abort requests to work to LUN=0 with mainline target code)
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
Force large capacity (> 0xFFFFFFFF blocks) drives to use READ/WRITE(16) instead
of READ/WRITE(10). Some(most/all?) USB enclosures do not like READ(10) commands
when a large capacity drive is installed. This issue was reported and discussed
here: http://marc.info/?l=linux-usb&m=135247705222324
Signed-off-by: Jason J. Herne <hernejj@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch handles SCSI dma mapping failure case. Reporting error code to the
upper layer instead of BUG_ON().
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
virtscsi_queuecommand was leaking memory when the virtio queue was full.
Tested: Guest operates correctly even with very small queue sizes, validated
we're not leaking kmalloc-192 sized allocations anymore.
Signed-off-by: Eric Northup <digitaleric@google.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed setting sequential delivery bit in a service class that is not valid
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix bug with Target Resets and FCP2 devices
Create module parameter to disable Target Reset on FCP-Tape devices
when a "bus reset" is requested. Default is to reset all devices on
bus reset.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed boot from san failure when SLI4 FC device presented on the same PCI bus
The request_firmware interface can induce delays while looking
for firmware files, even if no fw file is present. In some situations
the delays exceeded scan_wait timeouts, resulting in situations in which
the boot device had not been discovered in time. Boot Device does not
need to be on a lpfc device.
Change request_firmware use to be module paramater driven. Default is to
not attempt firmware download on boot. Add sysfs parameter to invoke
firmware update.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support IOP RR4520/RR4522 which are based on Marvell frey.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed the individual PCI DEVICE ID checking inside bnx2i. The device
type can easily be read from the corresponding cnic->flags. This will
free bnx2i from having to get updated for every new device ID that gets
added.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver periodically checks adapter state,is up fine or not.
Based on the value updates the internal structures of driver.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The MBX timeout value set to 100 and if adapter doesn;t
return response in that time driver will return from waiting
for completion with an error to the caller. In the earlier code
driver use to wait until MBX response comes from adapter.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix issue of displaying adapter family through the sysfs
entry for each Scsi_Host created for the adapter.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The completion events returned by adapter differs based on the
adapter. This fix checks for the adapter type and process the
completion event.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For updating session context on adapter, V2 version is to
be used with the latest adapter. This fix checks for the adapter type
and uses correct version of session context.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Latest adapters use the V2 version of WRB. This fix checks for the
adapter type and uses appropriate version of WRB.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For latest adapters, V2 version of cq_create MBX_CMD is to be used. When
driver is loaded depending on the adapter type appropriate cq_create command
will be called.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix the max EQ created when driver is loaded. Max EQ for
for new adapters will be 64.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix support for Skyhawk-R adapter by populating the pci_id_table
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix return value and typo in the message displayed.
Fix the goto label when wrb_hanlde allocation fails.
Fix the error message display in beiscsi_alloc_pdu
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Kernel used to panic while running IO is disable mode, as there
was an issue with getting the correct EQ on which completion has come.
Fix done is create workqueue per hba and work item for each EQ created.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The maximum EQ that can be created for a function is 8. Check the
CPU online count and create only 8 EQ if CPU_Count >= 8
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In contorl path of the driver the task was mapped using
pci_map_single which was not unmapped when the completion
for the task had come.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Display the event string along with the opcode and CID on which
an event has occured.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed soft_reset problem which driver modified
all 32bit before a write on second pass.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds the support for the following two read-only sysfs attributes
to scsi_osd class members : osdname & systemid
These attributes will show up as below in sysfs class hierarchy:
/sys/class/scsi_osd/osdX/osdname
/sys/class/scsi_osd/osdX/systemid
The osdname & systemid are OSD device attributes which uniquely
identify a device on the network, while it's IP and certainly
it's /dev/osdX device path might change.
Userspace utilities (e.g. mkfs.exofs) can parse these attributes to
identify the correct OSD in safer and faster way.
(Today osd apps open each device in the system and send a
attributes query for these, in order to access the user
requested device)
Signed-off-by: Sachin Bhamare <sbhamare@panasas.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_register_driver will register a prep_fn() function, which
in turn migh need to use the sd_cdp_pool for DIF.
Which hasn't been initialised at this point, leading to
a crash. So reshuffle the init_sd() and exit_sd() paths
to have the driver registered last.
Signed-off-by: Joel D. Diaz <joeldiaz@us.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support requests with more than one bio payload for discards. The total
number of bytes to be discarded is stored in req->__data_len and used in
sd_done() to complete the I/O.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.
We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull sparc fixes from David Miller:
"Several build/bug fixes for sparc, including:
1) Configuring a mix of static vs. modular sparc64 crypto modules
didn't work, remove an ill-conceived attempt to only have to build
the device match table for these drivers once to fix the problem.
Reported by Meelis Roos.
2) Make the montgomery multiple/square and mpmul instructions actually
usable in 32-bit tasks. Essentially this involves providing 32-bit
userspace with a way to use a 64-bit stack when it needs to.
3) Our sparc64 atomic backoffs don't yield cpu strands properly on
Niagara chips. Use pause instruction when available to achieve
this, otherwise use a benign instruction we know blocks the strand
for some time.
4) Wire up kcmp
5) Fix the build of various drivers by removing the unnecessary
blocking of OF_GPIO when SPARC.
6) Fix unintended regression wherein of_address_to_resource stopped
being provided. Fix from Andreas Larsson.
7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
Larsson."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
sparc: Support atomic64_dec_if_positive properly.
of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
sparc: Add sparc support for platform_get_irq()
sparc: Allow OF_GPIO on sparc.
qlogicpti: Fix build warning.
sparc: Wire up sys_kcmp.
sparc64: Improvde documentation and readability of atomic backoff code.
sparc64: Use pause instruction when available.
sparc64: Fix cpu strand yielding.
sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The build warns:
drivers/scsi/qlogicpti.c: In function 'qpti_sbus_probe':
drivers/scsi/qlogicpti.c:1316:45: warning: passing argument 1 of 'scsi_host_alloc' discards 'const' qualifier from pointer target type [enabled by default]
include/scsi/scsi_host.h:778:26: note: expected 'struct scsi_host_template *' but argument is of type 'const struct scsi_host_template *'
The problem is that of_device_id->data is a const void pointer.
This is pretty silly in this specific instance, because for all
matched device IDs we set match->data to the same value,
&qpti_template.
So just use that directly instead of the unnecessary and improperly
typed abstraction.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the target code to change the loop_id or s_id of a
target session in reaction to an FC fabric change. However, the
session structures are stored in tables that are indexed by these two
keys, and if we just change the session structure but leave the
pointers to it in the old places in the table, havoc can ensue. For
example, a new session might come along that should go in the old slot
in the table and overwrite the old session pointer.
To handle this, add a new tgt_ops->update_sess() method that also
updates the "by loop_id" and "by s_id" lookup tables when a session
changes, so that the keys where a session pointer is stored in these
tables always matches the keys in the session structure itself.
(nab: Drop unnecessary double inversion with FCF_CONF_COMP_SUPPORTED
usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
My draft of SPC-4 says the following about the SCSI name string in
inquiry VPD page 83h:
The SCSI NAME STRING field starts with either:
a) the four UTF-8 characters 'eui.' concatenated with 16, 24, or
32 hexadecimal digits (i.e., the UTF-8 characters 0 through 9
and A through F) for an EUI-64 based identifier (see
7.8.6.5). The first hexadecimal digit shall be the most
significant four bits of the first byte (i.e., most significant
byte) of the EUI-64 based identifier;
b) the four UTF-8 characters 'naa.' concatenated with 16 or 32
hexadecimal digits for an NAA identifier (see 7.8.6.6). The
first hexadecimal digit shall be the most significant four bits
of the first byte (i.e., most significant byte) of the NAA
identifier; or
c) the four UTF-8 characters 'iqn.' concatenated with an iSCSI
Name for an iSCSI-name based identifier (see iSCSI).
However, the .tpg_get_wwn method for tcm_qla2xxx formats the WWN so
the SCSI name string looks like "52:4a:93:7d:24:5f:b2:12,t,0x0001".
This patch corrects the code so that VPD 83h gives a SPC-compliant
SCSI name string like "naa.524a937d245fb212,t,0x0001" while leavig
other uses alone (so configfs will still work with ':' separated WWNs).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All other callers of qlt_update_vp_map() already hold ->vport_slock
while updating the vp target map, so go ahead and add the missing
->vport_slock within qla24xx_disable_vp() code.
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roland Dreier <roland@purestorage.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A collection of warning fixes on non-ARM code from Arnd Bergmann:
* 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
pcmcia: sharpsl: don't discard sharpsl_pcmcia_ops
USB: EHCI: mark ehci_orion_conf_mbus_windows __devinit
mm/slob: use min_t() to compare ARCH_SLAB_MINALIGN
SCSI: ARM: make fas216_dumpinfo function conditional
SCSI: ARM: ncr5380/oak uses no interrupts
This is an assorted set of stragglers into the merge window with driver
updates for megaraid_sas, lpfc, bfi and mvumi. It also includes some fairly
major fixes for virtio-scsi (scatterlist init), scsi_debug (off by one error),
storvsc (use after free) and qla2xxx (potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQeJfDAAoJEDeqqVYsXL0MhqgH/Rq7ebKJvKcUoKsTJKsZ2H0V
iaK5wBvhPBXLxYF5fMEnOwOPT34ry4SWJ7IqTKQqZItx1kqZuG4OTUjmueUCxaMb
7ELFWqyV1z7lyt+XAvNt/RTdMFl3n2SkOxgQJ8kzTPYzEHcE8GCH+dtuqzxoOUqx
styM6DE9Y5cQR1ozacj/QDMv4gn2jclclYgaxR2OTqzqQFeTMzn5KfRH4b6vYtos
ZuYlFE4uaAQhsUGeOqTcGlMvot4tyz4KGO4oy4xkHRQXRVQ52Ve8slRr1z4EUJ3H
rOpz869Y97vnSDFyXuJDa8PpbDd5KOU1uJBxE/3LlCoXIQj4u71hDXETRtq8jtg=
=T50d
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI updates from James Bottomley:
"This is an assorted set of stragglers into the merge window with
driver updates for megaraid_sas, lpfc, bfi and mvumi. It also
includes some fairly major fixes for virtio-scsi (scatterlist init),
scsi_debug (off by one error), storvsc (use after free) and qla2xxx
(potential deadlock).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (49 commits)
[SCSI] storvsc: Account for in-transit packets in the RESET path
[SCSI] qla2xxx: fix potential deadlock on ha->hardware_lock
[SCSI] scsi_debug: Fix off-by-one bug when unmapping region
[SCSI] Shorten the path length of scsi_cmd_to_driver()
[SCSI] virtio-scsi: support online resizing of disks
[SCSI] virtio-scsi: fix LUNs greater than 255
[SCSI] virtio-scsi: initialize scatterlist structure
[SCSI] megaraid_sas: Version, Changelog, Copyright update
[SCSI] megaraid_sas: Remove duplicate code
[SCSI] megaraid_sas: Add SystemPD FastPath support
[SCSI] megaraid_sas: Add array boundary check for SystemPD
[SCSI] megaraid_sas: Load io_request DataLength in bytes
[SCSI] megaraid_sas: Add module param for configurable MSI-X vector count
[SCSI] megaraid_sas: Remove un-needed completion_lock spinlock calls
[SCSI] lpfc 8.3.35: Update lpfc version for 8.3.35 driver release
[SCSI] lpfc 8.3.35: Fixed not reporting logical link speed to SCSI midlayer when QoS not on
[SCSI] lpfc 8.3.35: Fix error with fabric service parameters causing performance issues
[SCSI] lpfc 8.3.35: Fixed SCSI host create showing wrong link speed on SLI3 HBA ports
[SCSI] lpfc 8.3.35: Fixed not checking solicition in progress bit when verifying FCF record for use
[SCSI] lpfc 8.3.35: Fixed messages for misconfigured port errors
...
Pull scsi target updates from Nicholas Bellinger:
"Things have been calm for the most part with no new fabric drivers in
flight for v3.7 (we're up to eight now !), so this update is primarily
focused on addressing a few long-standing items within target-core and
iscsi-target fabric code.
The highlights include:
- target: Simplify fabric sense data length handling (roland)
- qla2xxx: Fix endianness of task management response code (roland)
- target: fix truncation of mode data, support zero allocation length
(paolo)
- target: Properly support zero-length commands in normal processing
path (paolo)
- iscsi-target: Correctly set 0xffffffff field within ISCSI_OP_REJECT
PDU (ronnie + nab)
- iscsi-target: Add explicit set of cache_dynamic_acls=1 for TPG
demo-mode (ronnie + nab)
- target/file: Re-enable optional fd_buffered_io=1 operation (nab +
hch)
- iscsi-target: Add MaxXmitDataSegmenthLength forr target ->
initiator MDRSL declaration (nab)
- target: Add target_submit_cmd_map_sgls for SGL fabric memory
passthrough (nab + hch)
- tcm_loop: Convert I/O path to use target_submit_cmd_map_sgls (hch +
nab)
- tcm_vhost: Convert I/O path to use target_submit_cmd_map_sgls (nab
+ hch)
The last series for adding a new target_submit_cmd_map_sgls() fabric
caller (as requested by hch) that accepts pre-allocated SGL memory
(using existing logic), along with converting tcm_loop + tcm_vhost has
only been in -next for the last days, but has gotten enough review
+testing and is clear enough a mechanical change that I think it's
reasonable to merge for -rc1 code.
Thanks again to everyone who contributed this round! Extra special
thanks to Roland (PureStorage) for tracking down the qla2xxx target
TMR response code endian issue, and to Paolo (Redhat) for resolving
the long standing zero-length CDB issues within target-core between
virtual and pSCSI backends."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
iscsi-target: Bump defaults for nopin_timeout + nopin_response_timeout values
iscsit: proper endianess conversions
iscsit: use the itt_t abstract type
iscsit: add missing endianess conversion in iscsit_check_inaddr_any
iscsit: remove incorrect unlock in iscsit_build_sendtargets_resp
iscsit: mark various functions static
target/iscsi: precedence bug in iscsit_set_dataout_sequence_values()
target/usb-gadget: strlen() doesn't count the terminator
target/usb-gadget: remove duplicate initialization
tcm_vhost: Convert I/O path to use target_submit_cmd_map_sgls
target: Add control CDB READ payload zero work-around
tcm_loop: Convert I/O path to use target_submit_cmd_map_sgls
target: Add target_submit_cmd_map_sgls for SGL fabric memory passthrough
iscsi-target: Add explicit set of cache_dynamic_acls=1 for TPG demo-mode
iscsi-target: Change iscsi_target_seq_pdu_list.c to honor MaxXmitDataSegmentLength
iscsi-target: Add MaxXmitDataSegmentLength connection recovery check
iscsi-target: Convert incoming PDU payload checks to MaxXmitDataSegmentLength
iscsi-target: Enable MaxXmitDataSegmentLength operation in login path
iscsi-target: Add base MaxXmitDataSegmentLength code
target/file: Re-enable optional fd_buffered_io=1 operation
...
The fas216_dumpinfo function is only used by __fas216_checkmagic,
which is conditionally compiled, so we should put both functions
inside of the same #ifdef.
Without this patch, building rpc_defconfig results in:
drivers/scsi/arm/fas216.c:182:13: warning: 'fas216_dumpinfo' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-scsi@vger.kernel.org
The ncr5380 driver is included by multiple board specific
drivers, which may or may not use the interrupt handler.
The oak variant doesn't, and should set the DONT_USE_INTR
macro.
Without this patch, building rpc_defconfig results in:
drivers/scsi/arm/../NCR5380.c:1160:20: warning: 'oakscsi_intr' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-scsi@vger.kernel.org
Properly account for I/O in transit before returning from the RESET call.
In the absense of this patch, we could have a situation where the host may
respond to a command that was issued prior to the issuance of the RESET
command at some arbitrary time after responding to the RESET command.
Currently, the host does not do anything with the RESET command.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Lockdep reports:
=== [ cut here ] ===
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.6.0-0.0.0.28.36b5ec9-default #1 Not tainted
---------------------------------------------------------
qla2xxx_1_dpc/368 just changed the state of lock:
(&(&ha->vport_slock)->rlock){+.....}, at: [<ffffffffa009b377>] qla2x00_configure_hba+0x197/0x3c0 [qla2xxx]
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&(&ha->hardware_lock)->rlock){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&ha->vport_slock)->rlock);
local_irq_disable();
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->vport_slock)->rlock);
<Interrupt>
lock(&(&ha->hardware_lock)->rlock);
=== [ cut here ] ===
Fix the potential deadlock by disabling IRQs while holding ha->vport_slock.
Reported-and-tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently it is possible to unmap one more block than user requested to
due to the off-by-one error in unmap_region(). This is probably due to
the fact that the end variable despite its name actually points to the
last block to unmap + 1. However in the condition it is handled as the
last block of the region to unmap.
The bug was not previously spotted probably due to the fact that the
region was not zeroed, which has changed with commit
be1dd78de5. With that commit we were able
to corrupt the ext4 file system on 256M scsi_debug device with LBPRZ
enabled using fstrim.
Since the 'end' semantic is the same in several functions there this
commit just fixes the condition to use the 'end' variable correctly in
that context.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch tries to shorten the path length of scsi_cmd_to_driver(). As only
REQ_TYPE_BLOCK_PC commands can be submitted without a driver, so we could
avoid the related NULL checking, as long as we make sure we don't use it for
REQ_TYPE_BLOCK_PC type commands. Plus, this fixes a bug where you get
different behaviors from REQ_TYPE_BLOCK_PC commands when a driver is and isn't
attached.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support the LUN parameter change event. Currently, the host fires this event
when the capacity of a disk is changed from the virtual machine monitor.
The resize then appears in the kernel log like this:
sd 0:0:0:0: [sda] 46137344 512-byte logical blocks: (23.6 GB/22.0 GIb)
sda: detected capacity change from 22548578304 to 23622320128
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
virtio-scsi needs to report LUNs greater than 256 using the "flat"
format. Because the Linux SCSI layer just maps the SCSI LUN to
an u32, without any parsing, these end up in the range from 16640
to 32767. Fix max_lun to account for the possibility that logical
unit numbers are encoded with the "flat" format.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The sg struct is used without being initialized, which breaks
when CONFIG_DEBUG_SG is enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Load io_request->DataLength in bytes for newer firmware that supports high
availability.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed messages for misconfigured port errors to be consistent for
all OS platforms.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In LUN RESET testing involving NetApp targets, it is observed that LUN
RESET is failing. The fc_fcp_resp() is not completing the completion
for the LUN RESET task since fc_fcp_resp assumes that the FCP_RSP_INFO
is 8 bytes with the 4 byte reserved field, where in case of NetApp targets
the FCP_RSP to LUN RESET only has 4 bytes of FCP_RSP_INFO. This leads
fc_fcp_resp to error out w/o completing the task completion, eventually
causing LUN RESET to be escalated to host reset, which is not very nice.
Per FCP-3 r04, clause 9.5.15 and Table 23, the FCP_RSP_INFO field can be either
4 bytes or 8 bytes, with the last 4 bytes as "Reserved (if any)". Therefore it
is valid to have 4 bytes FCP_RSP_INFO like some of the NetApp targets behave.
Fixing this by validating the FCP_RSP_INFO against both the two spec allowed
length.
Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SCSI errors were generated while writing to LUNs
connected via NPIV ports.
Debugging this it was found that the FCoE packets
transmitted via the NPIV ports were not tagged with
correct user priority as negotiated with peer by DCB
agent. This resulted in FCoE traffic going with priority
zero(0) that did not have priority flow control (PFC)
enabled for it. The initiator after transferring data
to the target never saw any reply indicating the transfer
was complete. This resulted in error recovery (ABTS) and
SCSI command retries by the scsi-mid layer; eventually
resulting in I/O errors.
This patch fixes this issue by keeping the FCoE user
priority information in the fcoe_interface instance
that is common for both the physical port as well as
NPIV ports connected to that physical port; instead
of storing it in fcoe_port structure that has a per
port instance.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Modified the firmware naming convention to contain the
firmware image version (3.1.0.0).
- The new convention is <firmware-image>-<firmware-version>.bin
- The change will enforce loading only compatible firmware with this driver
and also avoid over-writing the old firmware image in-order to load new
version driver as the firmware names used to be the same.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add FRU sub-module to support FRU read/write/update.
- Add support to read/write from the temp FRU module.
[jejb: fix checkpatch issues]
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add Power On Hours display support during sfpshow
- Fix to properly set the diag temperature sensor status variable.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to configure minimum bandwidth for a pcifn.
- Minimum bandwith is guaranteed at per queue level.
- Added support to update pcifn bandwidth dynamically without
a server reboot.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add capability to limit the number of exchanges on a port to
avoid queue-full conditions from the target side.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to provide an option for user to configure the
bandwidth percentage for High/Medium/Low QoS priorities.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes such that once the PWWN is acquired from the fabric through FAA,
and if the FAPWWN configuration is modified on the switch side, driver should
show relevant information to the user.
- Added logic to cache the reason code when the given port is disabled implicitl
due to FAA error condition.
- If the port is disabled, while sending SCN to upper layer, update the
reason code appropriately. With this, BFA FC port state machine will enter
into faa_err_config state. This state will be shown to the user.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced support for D-Port which is a new port mode during which
link level diagnostics can be run.
- Provided mechanism to dynamically configure D-Port and initiate diagnostic
tests to isolate any link level issues.
- In D-Port mode, the HBA port does not participate in fabric or login to the
remote device or run data traffic.
- Diagnostic tests include running various loopback tests in conjunction with
the attached device.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Enhance tracing to include both tskim tag and event.
- Handle the tskim abort response from firmware in the
tskim state machine cleanup state and proceed with the
tskim cleanup.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to set the RHBA command max payload based on
the port configured frame size.
- Made changes to fix the driver/fw version size in FMDI structure.
- Fix to pass the fw version for FDMI attribute type
FDMI_HBA_ATTRIB_FW_VERSION rather than driver version.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to expose mfg day/month/year as part of the
adapter attributes for user space applications.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to check the flash controller status before IOC initialization.
- Made changes to poll on the FLASH_STS_REG bit to check if the flash controller
initialization is completed during the PLL init.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add support to handle STOP/DISABLE events in the IOCFC state machine.
- Made changes to bring the IOC down on a flash driver config read failure.
- Added logic to clean the use count and fail sync registers during IOCFC init.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add private loop topology support at 2G/4G/8G speeds with following
limitations
1. No support for multiple initiators in the loop
2. No public loop support. If attached to a loop with an FL_Port,
device continues to work as a private NL_Port in the loop
3. No auto topology detection. User has to manually set the
configured topology to loop if attaching to loop.
- When loop topology is configured, enabling FC port features
QoS/Trunk/TRL are not allowed and vice versa.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
The ACARD driver calls udelay() with a value > 2000, which leads to to
the following compilation error on ARM:
ERROR: "__bad_udelay" [drivers/scsi/atp870u.ko] undefined!
make[1]: *** [__modpost] Error 1
This is because udelay is defined on ARM, roughly speaking, as
#define udelay(n) ((n) > 2000 ? __bad_udelay() : \
__const_udelay((n) * ((2199023U*HZ)>>11)))
The argument to __const_udelay is the number of jiffies to wait divided
by 4, but this does not work unless the multiplication does not
overflow, and that is what the build error is designed to prevent. The
intended behavior can be achieved by using mdelay to call udelay
multiple times in a loop.
[jrnieder@gmail.com: adding context]
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
The st_mutex was created when the BKL was removed, and
prevents simultaneous st_open calls. It is better to
protect just the necessary data.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Acked-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We set the capacity to zero when we discovered a device formatted with
an unknown DIF protection type. However, the read_capacity code would
override the capacity and cause the device to be enabled regardless.
Make sd_read_protection_type() return an error if the protection type is
unknown. Also prevent duplicate printk lines when the device is being
revalidated.
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of FW hung ISP83XX generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
For ISP83XX risc_intr getting clear two times in case of polling mode.
risc_intr getting clear from interrupt_service_routine() as well
from process_mbox_intr() because of this driver may clear risc_intr
without processing interrupt.
Fix:
Do not clear risc_intr from process_mbox_intr().
Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
System panic on rmmod if probe_adapter had failed during driver load.
Call Trace:
[<ffffffffa071aa5a>] qla4xxx_abort_active_cmds+0x4a/0xa0 [qla4xxx]
[<ffffffffa07224db>] qla4xxx_free_adapter+0x1b/0x1b0 [qla4xxx]
[<ffffffffa073991f>] qla4xxx_remove_adapter+0x294/0x2c7 [qla4xxx]
[<ffffffff812930b7>] pci_device_remove+0x37/0x70
[<ffffffff8135006f>] __device_release_driver+0x6f/0xe0
[<ffffffff813501a8>] driver_detach+0xc8/0xd0
[<ffffffff8134ef0e>] bus_remove_driver+0x8e/0x110
[<ffffffff81350972>] driver_unregister+0x62/0xa0
[<ffffffff812933c4>] pci_unregister_driver+0x44/0xb0
[<ffffffffa0739659>] qla4xxx_module_exit+0x15/0x47 [qla4xxx]
[<ffffffff810addd4>] sys_delete_module+0x194/0x260
[<ffffffff8150326e>] ? do_page_fault+0x3e/0xa0
[<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b
Fix:
Do not cleanup resources on remove_adapter as they are cleaned up during
probe_adapter exit.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If IRQ allocation fails, it means system has run out of interrupt
vectors, so fail probe_adapter in case of IRQ allocation failure
and dont retry adapter initialization.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For ISP82xx mixed interrupt mode is not supported.
Hence prevent MSI/MSI-x from falling back to INTx mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Camram is reset by FW to default values after reboot/cold boot/pci reset.
In case of AER, PCI may need to reset so we need to set correct idc reg value
after PCIE error.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
In qla4_8xxx_error_recovery() IDC lock recovery is initiated as
IDC lock is held while enabling the interrupts
Fix:
Correctly handle IDC locking mechanism in qla4_8xxx_error_recovery().
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A quote from SPC-4: "While in the unavailable primary target port
asymmetric access state, the device server shall support those of
the following commands that it supports while in the active/optimized
state: [ ... ] d) SET TARGET PORT GROUPS; [ ... ]". Hence enable
sending STPG to a target port group that is in the unavailable state.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
John reports:
BUG: soft lockup - CPU#2 stuck for 23s! [kworker/u:8:2202]
[..]
Call Trace:
[<ffffffff8141782a>] scsi_remove_target+0xda/0x1f0
[<ffffffff81421de5>] sas_rphy_remove+0x55/0x60
[<ffffffff81421e01>] sas_rphy_delete+0x11/0x20
[<ffffffff81421e35>] sas_port_delete+0x25/0x160
[<ffffffff814549a3>] mptsas_del_end_device+0x183/0x270
...introduced by commit 3b661a9 "[SCSI] fix hot unplug vs async scan race".
Don't restart lookup of more stargets in the multi-target case, just
arrange to traverse the list once, on the assumption that new targets
are always added at the end. There is no guarantee that the target will
change state in scsi_target_reap() so we can end up spinning if we
restart.
Cc: <stable@vger.kernel.org>
Acked-by: Jack Wang <jack_wang@usish.com>
LKML-Reference: <CAEhu1-6wq1YsNiscGMwP4ud0Q+MrViRzv=kcWCQSBNc8c68N5Q@mail.gmail.com>
Reported-by: John Drescher <drescherjm@gmail.com>
Tested-by: John Drescher <drescherjm@gmail.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The length field in the host config packet is only 16-bit long, so
passing it 0x10000 (64K which is our standard PAGE_SIZE) doesn't
work and result in an empty config from the server.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that the iSeries code is gone the backend abstraction
in this driver is no longer necessary, which allows us to
consolidate the driver in one file.
The side effect is that the module name is now ibmvscsi.ko
which matches the driver hotplug name and fixes auto-load
issues.
[jejb:fix up checkpatch.pl errors]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move minidump code from qla4_8xxx_device_bootstrap() to
new function qla4_8xxx_get_minidump() to make code more
modular.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Device can go to READY state from COLD and skip INITIALIZATION,
In this case driver will never set IDC version from function
qla4_8xxx_device_bootstrap().
Fix:
1. Set IDC version at start of function qla4_82xx_need_reset_handler().
2. Set IDC version only if we are 1st driver to load.
3. Added new function qla4_8xxx_update_idc_reg() to set all idc reg at one
place.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ql4_8xxx_mark_entry_skipped to qla4_8xxx_mark_entry_skipped
ql4_attr_is_visible to qla4_attr_is_visible
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add "removable" module parameter to set the "removable" attribute of any
subsequently created debug block device. It is a writable driver option, so
that you can switch between removable and "fixed" media block devices in
between the add_host calls.
This is useful for being able to test the different behaviour/required
privileges in e. g. the udisks test suite.
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
while processing the stop firmware mailbox command on driver unload,
a interrupt is processed which causes kernel panic as the response
queue is not valid.
Fix is to clear the interrupt in free_adapter call just after
disabling the interrupts.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We always assign a dummy task context to a port in order to address a
silicon issue. We have 4 ports per controller. So when idle, there are always
exactly 4 TCs "active". The adaptive interrupt coalescing code uses number of
active TCs to figure out the coalescing values. However, we never hit "0" TCs
because of the 4 dummy TCs. Putting in fix so that we calculate this correctly.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This commit fixes a driver bug for SSP tasks that require task management
in the target after they complete in the SCU hardware. The problem was
manifested in the function "isci_task_abort_task", which tests
to see if the sas_task.lldd_task is non-NULL before allowing task
management; this bug would always NULL lldd_task in the SCU I/O completion
path even if target management was required, which would prevent
task / target manangement from happening.
Note that in the case of SATA/STP targets, error recovery is provided by
the libata error handler which is why SATA/STP device recovery worked
correctly even though SSP handling did not.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch consolidates the strings together. Purpose is to remove minor product strings extensions.
That way the future products with similar strings should not require change here.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a new vendor/product strings for netapp E series product.
Also consolidated the strings together with similar names.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
gcc 4.8 warns because the memset only clears sizeof(char *) bytes, not
the whole buffer. Use the correct buffer size and clear the whole sense
buffer.
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c: In
function 'bnx2fc_parse_fcp_rsp':
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c:1810:41:
warning: argument to 'sizeof' in 'memset' call is the same expression as
the destination; did you mean to provide an explicit length?
[-Wsizeof-pointer-memaccess]
memset(sc_cmd->sense_buffer, 0, sizeof(sc_cmd->sense_buffer));
^
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add a parameter that allows the host protection capabilities mask to be
provided at module load time.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Only a target device should return ABORTED COMMAND when a PI error is
discovered. The HBA should always set the sense key to ILLEGAL REQUEST.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hitachi Ultrastar 15K300 is quirky. Disable T10 PI (DIF).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We have encountered a few devices that misbehaved when operating in T10
PI mode. Allow T10 PI protection type to be overridden from userland.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It does not make sense to translate ref tags with unexpected values.
Instead we simply ignore them and let the upper layers catch the
problem. Ref tags that contain the expected value are still remapped.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If state is NON_BLOCKING and mutex_trylock is succeed,
the control flow goes to mutex_lock_interruptible() that is a deadlock.
[jejb: fixed coding style problems]
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: "Sreekanth Reddy" <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes an issues seen where a Fabric RSCN event was received
while the link was down, which resulted in repeated attempts to log back
into the fabric, which then failed, resulting in the ibmvfc driver
taking the host offline. Fix this by delaying taking any action
regarding the fabric RSCN until the link comes back up.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an abort request times out to the virtual fibre channel adapter,
the ibmvfc driver will kick off a reset of the adapter. This
patch ensures we wait for the both the abort request and the
request being aborted to be completed prior to exiting the
eh_abort handler. This fixes a bug where the ibmvfc driver
was erroneously returning success to the eh_abort handler
then later sending back a response to the same command.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use kzalloc rather than kmalloc followed by memset with 0.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Changes to avoid discovering NPIV port as remote port by the other
NPIV ports created on same physical port when all the NPIV ports are
part of the same zone in a fabric.
- Provided mechanism to support maximum number of target ports for a
given initiator port (physical port + NPIV ports) irrespective of the
way in which the initiator and target ports are zoned in the fabric.
- Introduced module_parameter max_rport_logins to restrict number of
remote ports discovery which includes target and initiator remote ports.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Changes to register node symbolic name with name server on the fabric
by sending CT commands RNN_ID and RSNN_NN.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to process mbox and error interrupts only if interrupts are
enabled, when running in INTx mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added few missing endian swap changes to support BFA on PowerPC.
- Added PCIE AER support to BFA:
a) Implemented the PCI error handler entry points.
b) Made changes to FCS state machine to handle STOP event from the
PCI error detected entry point.
c) Made changes to the IO Controller state machine to handle SUSPEND
event from the PCI error detected entry point.
d) Made changes to restart the BFA operations on a slot_reset completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added new hardware model Brocade-1867 information to
sysfs model description routine.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to split FCXP resources as request and response resources.
- The split will reduce the contention for FCXP resources in an open zone
config.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced rport qualifier structure and modified design to
export remote ports with valid pid or valid pwwn to the user space.
- Introduced old_pid field in the rport structure and made changes to
prevent re-creating a new remote port for an already existing rport
that is transitioning to a delete state. (Happens if we receive a RSCN
on the existing remote port that is getting deleted).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Implemented the FC function template set_vport_symbolic_name entry
point to modify the vport symbolic name from sysfs.
- Implemented support to send RSPN_ID to switch to register the
modified vport symbolic name.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On ISP83xx cards perform a fundamental reset instead of hot reset.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting this to 255 will cause any target with id 255 to not show up so leave
it at the default in our host template.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla2xxx show wrong PCIe(2.5Gb/s x8) speed in the kerenel message. It should be
5.0Gb/s.
Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Stale information in the temporary fcport created in
qla2x00_configure_local_loop() causes qla2x00_get_port_database() call
to fail. This reschedules scan, which gets stuck continuously in the
rescheduling-of-scan loop due to the failure.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update the driver copyright from 2003-2011 to 2003-2012.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minor changes to support loopback functionality with ISP83xx CNAs.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Store used fcport loop_id's in a bitmap so that as opposed to looping through
all fcports to find the next free loop_id, new loop_id lookup can be just be
done via bitops.
[jejb: plus fix for incorrect LOOPID_MAP_SIZE from Andrew Vasquez]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The qla2xxx firmware actually expects the task management response
code in a CTIO IOCB with SCSI status mode 1 to be in little-endian
byte order, ie the response code should be the first byte in the
sense_data[] array. The old code erroneously byte-swapped the
response code, which puts it in the wrong place on the wire and leads
to initiators thinking every task management request succeeds (since
they see 0 in the byte where they look for the response code).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor. CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected. This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not. Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug. This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Every fabric driver has to supply a se_tfo->set_fabric_sense_len()
method, just so iSCSI can return an offset of 2. However, every fabric
driver is already allocating a sense buffer and passing it into the
target core, either via transport_init_se_cmd() or target_submit_cmd().
So instead of having iSCSI pass the start of its sense buffer into the
core and then later tell the core to skip the first 2 bytes, it seems
easier for iSCSI just to do the offset of 2 when it passes the sense
buffer into the core. Then we can drop the se_tfo->set_fabric_sense_len()
everywhere, and just add a couple of lines of code to iSCSI to set the
sense data length to the beginning of the buffer right before it sends
it over the network.
(nab: Remove .set_fabric_sense_len usage from tcm_qla2xxx_npiv_ops +
change transport_get_sense_buffer to follow v3.6-rc6 code w/o
->set_fabric_sense_len usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are no callers of se_tfo->get_fabric_sense_len(), so we should
stop having every fabric driver implement it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.
[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.
One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets. When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.
This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.
This change only affects Broadcom's 5709 chipset.
Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
[<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>] [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50 EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS: 0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack: 000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
<IRQ> [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
[<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
[<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
[<ffffffff800125a0>] __do_softirq+0x89/0x133
[<ffffffff8005e30c>] call_softirq+0x1c/0x28
[<ffffffff8006d5de>] do_softirq+0x2c/0x7d
[<ffffffff8006d46e>] do_IRQ+0xee/0xf7
[<ffffffff8005d625>] ret_from_intr+0x0/0xa
<EOI> [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
[<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
[<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
[<ffffffff80049560>] cpu_idle+0x95/0xb8
[<ffffffff80078b1c>] start_secondary+0x479/0x488
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
