The pre-release GCC-4.6 now correctly flags this code as dead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we are running on a MX35 processor.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, for ISO and INT, a protocol driver must chose the value for
wMaxPacketSize arbitrarily. The value may be too low, resulting in lesser
than efficient operation or high enough to not work with all UDC drivers.
Take un-initialized wMaxPacketSize as a hint to provide maximum
possible packetsize for the selected endpoint. The protocol may
then choose a value not bigger than that.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added mct_u232_ioctl (implements TIOCMIWAIT command),
mct_u232_get_icount (implements TIOCGICOUNT command) and
mct_u232_msr_to_icount functions. MCT U232 P9 is one of a few usb to
serail adapters which converts USB +/-5v voltage levels to COM +/-15
voltages. So it can also power COM interfaced devices. This makes it
very usable for legacy COM interfaced data-acquisition hardware. I
tested new implementation with AWARE Electronics RM-60 radiation meter,
which sends pulse via RNG COM line whenever new particle is registered.
Signed-off-by: Vadim Tsozik <tsozik@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a set of new tests similar to the existing ones but using
transfer buffers at an "odd" address [ie offset of +1 from
the buffer obtained by kmalloc() or usb_alloc_coherent()]
The new tests are:
#17 : bulk out (like #1) using kmalloc and DMA mapping by USB core.
#18 : bulk in (like #2) using kmalloc and DMA mapping by USB core.
#19 : bulk out (like #1) using usb_alloc_coherent()
#20 : bulk in (like #2) using usb_alloc_coherent()
#21 : control write (like #14)
#22 : isochonous out (like #15)
#23 : isochonous in (like #16)
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ums_realtek is used to support the power-saving function
for Realtek RTS51xx USB card readers.
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 2232H high speed baud rates also support fractional baud
rate divisors, but when the performing the divisions before
the multiplication, the fractional bits are lost.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Acked-by: Mark Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With cmwq, there's no reason to use separate workqueues. Drop
uea_softc->work_q and use system_wq instead. The used work item is
sync flushed on driver detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change a typo from "desciptor" to "descriptor".
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts error codes specific to USB to generic error codes
that can be returned to user space. Tests showed that it is so small
that it is better inlined.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.38/core' of git://git.kernel.dk/linux-2.6-block: (43 commits)
block: ensure that completion error gets properly traced
blktrace: add missing probe argument to block_bio_complete
block cfq: don't use atomic_t for cfq_group
block cfq: don't use atomic_t for cfq_queue
block: trace event block fix unassigned field
block: add internal hd part table references
block: fix accounting bug on cross partition merges
kref: add kref_test_and_get
bio-integrity: mark kintegrityd_wq highpri and CPU intensive
block: make kblockd_workqueue smarter
Revert "sd: implement sd_check_events()"
block: Clean up exit_io_context() source code.
Fix compile warnings due to missing removal of a 'ret' variable
fs/block: type signature of major_to_index(int) to major_to_index(unsigned)
block: convert !IS_ERR(p) && p to !IS_ERR_NOR_NULL(p)
cfq-iosched: don't check cfqg in choose_service_tree()
fs/splice: Pull buf->ops->confirm() from splice_from_pipe actors
cdrom: export cdrom_check_events()
sd: implement sd_check_events()
sr: implement sr_check_events()
...
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
spi / PM: Support dev_pm_ops
PM: Prototype the pm_generic_ operations
PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
PM: Use dev_name() in core device suspend and resume routines
PM: Permit registration of parentless devices during system suspend
PM: Replace the device power.status field with a bit field
PM: Remove redundant checks from core device resume routines
PM: Use a different list of devices for each stage of device suspend
PM: Avoid compiler warning in pm_noirq_op()
PM: Use pm_wakeup_pending() in __device_suspend()
PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
PM: Prevent dpm_prepare() from returning errors unnecessarily
PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
PM / Hibernate: When failed, in_suspend should be reset
PM / Hibernate: hibernation_ops->leave should be checked too
Freezer: Fix a race during freezing of TASK_STOPPED tasks
PM: Use proper ccflag flag in kernel/power/Makefile
PM / Runtime: Fix comments to match runtime callback code
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
Protect d_subdirs and d_child with d_lock, except in filesystems that aren't
using dcache_lock for these anyway (eg. using i_mutex).
Note: if we change the locking rule in future so that ->d_child protection is
provided only with ->d_parent->d_lock, it may allow us to reduce some locking.
But it would be an exception to an otherwise regular locking scheme, so we'd
have to see some good results. Probably not worthwhile.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Protect d_unhashed(dentry) condition with d_lock. This means keeping
DCACHE_UNHASHED bit in synch with hash manipulations.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
The below patch fixes a typo "diable" to "disable" and also fixes another typo in a comment.
Please let me know if this is correct or not.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current code doesn't really enable the usb clocks so if they're disabled
when booting linux, the kernel/machine will hang as soon as someone is trying
to read a usb register
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A race exists when initializing ueagle-atm devices where the generic atm
device may not yet be created before the driver attempts to initialize
it's PHY signal state, which checks whether the atm device has been
created or not. This often causes the sysfs 'carrier' attribute to be
'1' even though no signal has actually been found.
uea_probe
usbatm_usb_probe
driver->bind (uea_bind)
uea_boot
kthread_run(uea_kthread) uea_kthread
usbatm_atm_init uea_start_reset
atm_dev_register UPDATE_ATM_SIGNAL
UPDATE_ATM_SIGNAL checks whether the ATM device has been created and if
not, will not update the PHY signal state. Because of the race that
does not always happen in time, and the PHY signal state remains
ATM_PHY_SIG_FOUND even though no signal exists.
To fix the race, just create the kthread during initialization, and only
after initialization is complete, start the thread that reboots the
device and initializes PHY state.
[ 3030.490931] uea_probe: calling usbatm_usb_probe
[ 3030.490946] ueagle-atm 8-2:1.0: usbatm_usb_probe: trying driver ueagle-atm with vendor=1110, product=9031, ifnum 0
[ 3030.493691] uea_bind: setting usbatm
[ 3030.496932] usb 8-2: [ueagle-atm] using iso mode
[ 3030.497283] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3021 byte buffer for rx channel 0xffff880125953508
<kthread already started before usbatm_usb_probe() has returned>
[ 3030.497292] usb 8-2: [ueagle-atm] (re)booting started
<UPDATE_ATM_SIGNAL checks whether ATM device has been created yet before setting PHY state>
[ 3030.497298] uea_start_reset: atm dev (null)
<and since it hasn't been created yet PHY state is not set>
[ 3030.497306] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3392 byte buffer for tx channel 0xffff8801259535b8
[ 3030.497374] usbatm_usb_probe: about to init
[ 3030.497379] usbatm_usb_probe: calling usbatm_atm_init
<atm device finally gets created>
[ 3030.497384] usbatm_atm_init: creating atm device!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() is being deprecated. Directly flush or cancel
work items instead.
* u_ether, isp1301_omap, speedtch conversions are straight-forward.
* ochi-hcd should only flush when quirk_nec() is true as otherwise the
work wouldn't have been initialized.
* In oti6858, cancel_delayed_work() + flush_scheduled_work() ->
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org
speedtch directly uses the internal timer and work members of a struct
delayed_work. Use a separate work item and timer instead.
* Nicolas Kaiser discovered that timer init was missing. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Tested-by: Nicolas Kaiser <nikai@nikai.net>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: linux-usb@vger.kernel.org
The device power.status field is too complicated for its purpose
(storing the information about whether or not the device is in the
"active" state from the PM core's point of view), so replace it with
a bit field and modify all of its users accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
So far the USBLED driver only supports Delcom's "USB Visual Signal
Indicator" (http://www.delcomproducts.com/products_USBLMP.asp). The
driver generates virtual files "red", "green", and "blue" under the
device's /sys/ directory, where color values can be read from and
written to.
This patch adds support for Dream Cheeky's "DL100B Webmail Notifier"
(http://www.dreamcheeky.com/webmail-notifier -- available from several
shops, such as http://www.conrad.at/ce/de/product/777048/USB-WEBMAIL).
This device isn't as pretty as Delcom's, but it's *far* cheaper, and
its 3 LEDs can be set in 32 brightness steps each. The grey envelope
contour can easily be removed, leaving a rather neutral white box (with
a few small holes), which is useful for generic signalling purposes.
Of course, the small circuit board can easily be put into a prettier
case.
The DL100B device pretends to be a HID, but the HID descriptor shows
that it's not overly useful as such (see below). The patch therefore
removes the "HID-ness" (hid-core.c, hid-ids.h), and adds the necessary
commands to usbled.c. The protocol info comes from the developer's
manual that Dream Cheeky kindly provided (815DeveloperManual.pdf).
HID descriptor:
0: 05 01 Usage Page 'Generic Desktop Controls'
2: 09 10 Usage 'Reserved'
4: a1 01 Collection 'Application (mouse, keyboard)'
6: 05 00 Usage Page 'Undefined'
8: 19 10 Usage Minimum = 16
10: 29 11 Usage Maximum = 17
12: 15 00 Logical Minimum = 0
14: 25 0f Logical Maximum = 15
16: 75 08 Report Size = 8
18: 95 08 Report Count = 8
20: 91 02 Output data *var abs lin pref-state null-pos non-vol bit-field
22: 19 10 Usage Minimum = 16
24: 29 11 Usage Maximum = 17
26: 15 00 Logical Minimum = 0
28: 25 0f Logical Maximum = 15
30: 75 08 Report Size = 8
32: 95 08 Report Count = 8
34: 81 00 Input data array abs lin pref-state null-pos non-vol bit-field
36: c0 End Collection
Signed-off-by: Melchior FRANZ <mfranz@aon.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: gadget: Allow function access to device ID data during bind()"
USB: misc: uss720.c: add another vendor/product ID
USB: usb-storage: unusual_devs entry for the Samsung YP-CP3
USB: gadget: Remove suspended sysfs file before freeing cdev
USB: core: Add input prompt and help text for USB_OTG config
USB: ftdi_sio: Add D.O.Tec PID
xhci: Fix issue with port array setup and buggy hosts.
This reverts commit 1ab8323874.
Turns out this doesn't allow for the device ids to be overridden
properly, so we need to revert the thing.
Reported-by: Jef Driesen <jefdriesen@telenet.be>
Cc: Robert Lukassen <Robert.Lukassen@tomtom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fabio Battaglia report that he has another cable that works with this
driver, so this patch adds its vendor/product ID.
Signed-off-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an unusual_devs entry for the Samsung YP-CP3 MP4 player.
User was getting the following errors in dmesg:
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: USB disconnect, address 2
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb:<2>ldm_validate_partition_table(): Disk read failed.
Dev sdb: unable to read RDB block 0
unable to read partition table
Signed-off-by: Vitaly Kuznetsov <vitty@altlinux.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdev struct is accessed in suspended sysfs show function. So
remove sysfs file before freeing the cdev in composite_unbind.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bd6882 commit (usb: gadget: fix Kconfig warning) removes
the duplicate USB_OTG config from gadget/Kconfig. But
does not copy the input prompt and help text to the original
config defined in core/Kconfig. Add them now.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Willem-Jan noticed that the ftdi_sio driver did not support the
TIOCSERGETLSR ioctl, and some userspace programs rely on it. This patch
adds the support.
Reported-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Tested-by: Willem-Jan de Hoog <wdehoog@exalondelft.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to read/write to the i.MX OTG viewport register it is necessary to setup
the PORTSCx register first.
By default i.MX OTG port is configured for USB serial PHY. In order to use a ULPI PHY
the PORTSCx register needs to be configured properly.
commit 724c852 (USB: ehci/mxc: compile fix) placed the PORTSC setup after the OTG
viewport is accessed and this causes ULPI read/write to fail.
Revert the PORTSC setup order.
Tested on a MX31PDK board with a ISP1504 transceiver:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
mxc-ehci mxc-ehci.0: initializing i.MX USB Controller
ULPI transceiver vendor/product ID 0x04cc/0x1504
Found NXP ISP1504 ULPI transceiver.
ULPI integrity check: passed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a free_irq() call on vbus gpio when we remove udc so that the
vbus irq is properly released.
Signed-off-by: Rob Emanuele <rje@crystalfontz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TLL channel enable code searches for the wrong mask, and
could end up enabling the wrong port. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the ohci-omap3 driver, not ehci-omap. Correct this
obvious typo.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
