v2: As pointed out by Hans J. Koch we have to claim we can do 24bit to
make software like X work. We are lucky on i.MX that 18bit support
has the necessary gaps in the fields to do so.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The in kernel FEC driver has recently been ported to a platform driver.
Add a platform_device for it and register it for pcm038 and mx27ads.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX31ADS supports pluggable PMU modules, including the WM835x based
Wolfson Microelectronics 1133-EV1. These boards provide power, audio,
RTC and watchdiog services to the system. This patch adds initial support
for those boards in I2C mode.
Currently support is limited by the available support for the features
of the i.MX31 in the mainline kernel. Some further work will be needed
once other PMU modules are supported and once there is SPI support.
Many of the regulator constraints will be sharable with other PMU
boards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This example takes advantage of the possibility to use tables of iomux
configs.
This is inspired from mx1-mx2 iomux code. It allows a better code
readability.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This new implemenatation avoids that two physical pins are claimed by
the same driver (also with the the gpr hardware modes).
The gpio kernel lib is also called when a capable gpio pin is assigned
its gpio function.
The mxc_iomux_mode function is still here for backward compatibility but
should not be used anymore.
V2:
In the precendent revision, the iomux code was claiming a pin when its
hardware mode was changed. This was uncorrect: when the hardware mode is
changed, the pin must still be claimed through the iomux.
In order to have a pin working in mode hw2, we must fist issue the
mxc_iomux_set_gpr call and then the corresponding mxc_iomux_mode calls
with the FUNC mode (usually done with mxc_iomux_setup_multiple_pins).
The reverse calls must be done to fee the pins.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
... from both mx27ads.c and pcm038.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Several of the macros in mx31ads.h depend on mx31.h which is no longer
included in quite so many standard headers as it once was. Include it
directly so we can build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX I2C driver has not yet been merged into mainline but it is
near to that and the device defintions don't depend directly on it
so we can add the devices now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch mimicks what Martin wrote on the mailing list:
* move arch/arm/mach-imx/include/mach/imxfb.h into
arch/arm/mach-mxc/include/mach/imxfb.h
* changes Kconfig so that CONFIG_FB_IMX is selectable
* adds a platform device (copied from some pengutronix
patches)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* define new CONFIG_ARCH_MX21 (this one is currently mutually exclusive to
CONFIG_ARCH_MX27, but this might change)
* splits one header file. Memory definitions, interrupt sources,
DMA channels are split into common part, i.MX27 specific and i.MX21
specific.
* guard access to UART5/UART6, which don't exist on i.MX21
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Here are some of the warnings that get fixed by this:
> 200 times: warning: cast adds address space to expression (<asn:2>)
twelve times: warning: symbol 'xxx' was not declared. Should it be static
two times: warning: symbol 'clock' shadows an earlier one
five times: warning: incorrect type in initializer (different address spaces)
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch only adds general clkdev support without actually switching
any MXC architecture to clkdev.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- rename mxc_clocks_init to architecture specific versions. This
allows us to have more than one architecture compiled in.
- call mxc_timer_init from clock initialisation instead from board
code
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We had 3 versions of this function in clock support for MX1/2/3
Use a single one instead. I picked the one from the MX3 as it seems
to calculate more accurate as the other ones. Also, on MX27 and MX31 mfn
can be negative, this hasn't been handled correctly on MX27 since now.
This patch has been tested on MX27 and MX31 and produces the same clock
frequencies for me.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* adds Kconfig variables
* specifies different physical address for i.MX21 because of the
different memory layouts
* disables support for UART5/UART6 in the i.MX serial driver
(the i.MX21 doesn't have those modules)
Based on code from "Martin Fuzzey" <mfuzzey@gmail.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* removed iomux-mx1-mx2.h completely
* distributes the former contents to four different files (iomux-mx1.h,
iomux-mx21.h, iomux-mx27.h and the file iomux-mx2x.h, which is common to
both i.MX21 and i.MX27).
* adds all documented IOMUX definitions for i.MX21 and i.MX27
* fixes a few that were wrong (PD14_AOUT_FEC_CLR, PE16_AF_RTCK).
* don't silenly include <linux/io.h>
* and fixes all collateral damage from above
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add gpio vbus detection to udc driver, by taking advantage
of the new gpio_vbus driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
CSB701 is one of baseboards that can be used with CSB726 SOM.
This currently adds support for button and LED on the board.
More to come later.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The typo was originally fixed by Mike Rapoport and missed. And is
later reported by Matthias Meier.
Signed-off-by: Matthias Meier <matthias.j.meier@gmx.net>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The current use of these macros works well when the conversion is
entirely linear. In this case, we can be assured that the following
holds true:
__va(p + s) - s = __va(p)
However, this is not always the case, especially when there is a
non-linear conversion (eg, when there is a 3.5GB hole in memory.)
In this case, if 's' is the size of the region (eg, PAGE_SIZE) and
'p' is the final page, the above is most definitely not true.
So, we must ensure that __va() and __pa() are only used with valid
kernel direct mapped RAM addresses. This patch tweaks the code
to achieve this.
Tested-by: Charles Moschel <fred99@carolina.rr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150
On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a Non-cacheable Normal ARM executable memory type,
MT_MEMORY_NONCACHED.
On OMAP3, this is used for rapid dynamic voltage/frequency scaling in
the VDD2 voltage domain. OMAP3's SDRAM controller (SDRC) is in the
VDD2 voltage domain, and its clock frequency must change along with
voltage. The SDRC clock change code cannot run from SDRAM itself,
since SDRAM accesses are paused during the clock change. So the
current implementation of the DVFS code executes from OMAP on-chip
SRAM, aka "OCM RAM."
If the OCM RAM pages are marked as Cacheable, the ARM cache controller
will attempt to flush dirty cache lines to the SDRC, so it can fill
those lines with OCM RAM instruction code. The problem is that the
SDRC is paused during DVFS, and so any SDRAM access causes the ARM MPU
subsystem to hang.
TI's original solution to this problem was to mark the OCM RAM
sections as Strongly Ordered memory, thus preventing caching. This is
overkill: since the memory is marked as non-bufferable, OCM RAM writes
become needlessly slow. The idea of "Strongly Ordered SRAM" is also
conceptually disturbing. Previous LAKML list discussion is here:
http://www.spinics.net/lists/arm-kernel/msg54312.html
This memory type MT_MEMORY_NONCACHED is used for OCM RAM by a future
patch.
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds __devinit and __devexit macros to the module probe and
remove functions in MMCI. Now includes the __devexit_p() thing too.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent the kernel from being crashed by a divide-by-zero operation when
supplied an incorrectly filled 'struct fb_var_screeninfo' from userland.
Previously i810_main.c:1005 (i810_check_params) was using the global
'yres' symbol previously defined at i810_main.c:145 as a module parameter
value holder (i810_main.c:2174). If i810fb is compiled-in or if this
param doesn't get a default value, this direct usage leads to a
divide-by-zero at i810_main.c:1005 (i810_check_params). The patch simply
replace the 'yres' global, perhaps undefined symbol usage by a given
parameter structure lookup.
This problem occurs with directfb, mplayer -vo fbdev, SDL library.
It was also reported ( but non solved ) at:
http://mail.directfb.org/pipermail/directfb-dev/2008-March/004050.html
Signed-off-by: Samuel CUELLA <samuel.cuella@supinfo.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There isn't any mcfqspi.h in the tree, and without it everything inside the
#ifdef CONFIG_SPI is uncompilable.
Signed-off-by: Steven King <sfking@fdwdc.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the RCU documentation to call out the need for callers of
primitives like call_rcu() and synchronize_rcu() to prevent subsequent RCU
readers from hazard.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were returning early in the sysfs directory cleanup function if the
user belonged to a non init usernamespace. Due to this a lot of the
cleanup was not done and we were left with a leak. Fix the leak.
Reported-by: Serge Hallyn <serue@linux.vnet.ibm.com>
Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit e480814f13 ("[MTD] [MAPS] physmap:
fix wrong free and del_mtd_{partition,device}") introduces a NULL pointer
dereference in physmap_flash_remove when called from the error path in
physmap_flash_probe (if map_probe failed).
Call del_mtd_{partition,device} only if info->cmtd was not NULL.
Reported-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When GTT size is equal to amount of video memory, the amount of GTT
entries is computed lower than zero, which is invalid and leads to
off-by-one error in intel_i915_configure()
Originally posted here:
http://bugzilla.kernel.org/show_bug.cgi?id=12539http://bugzilla.redhat.com/show_bug.cgi?id=445592
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 771999b65f ("[MTD] DataFlash: bugfix,
binary page sizes now handled") broke support for probing AT45DB321C flash
chips. These chips do not support the "page size" status bit, so if we
match the JEDEC id return early.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a problem in the IDR system, where an idr_remove_all() hands a data
element to call_rcu() (via free_layer()) before making that data element
inaccessible to new readers. This is very bad, and results in readers
still having a reference to this data element at the end of the grace
period.
Tests on large machines that concurrently map and unmap user-space memory
within the same multithreaded process result in crashes within about five
minutes. Applying this patch increases the kernel's longevity to the
three-to-eight-hour range.
There appear to be other similar problems in idr_get_empty_slot() and
sub_remove(), but I fixed the easy one in idr_remove_all() first. It is
therefore no surprise that failures still occur.
Located-by: Milton Miller II <miltonm@austin.ibm.com>
Tested-by: Milton Miller II <miltonm@austin.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Very annoying when working with containters.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix bug to make agp work with dri
Jeffrey reported that dri does work with 64bit, but doesn't work with
32bit it turns out NB aperture is 32M, aperture on agp is 128M
64bit is using 64M for vaidation for 64 iommu/gart 32bit is only using
32M..., and will not update the nb aperture.
So try to compare nb apterture and agp apterture before leaving not
touch nb aperture.
Reported-by: Jeffrey Trull <jetrull@sbcglobal.net>
Tested-by: Jeffrey Trull <jetrull@sbcglobal.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ->put_char changes
* HIGHMEM is bogus it seems, there is no kmap_atomic() et al
* some includes
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Chris Zankel <zankel@tensilica.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7468 chip supports VRM10 sensors just like the adt7463; add a
missing check for it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
