* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Specify chip revision at attach time rather than a firmware image.
This is a better way to ensure that the correct firmware is loaded
for the correct revision of the chip.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
convert the firmware configuration attach-time parameter from
a pointer to an integer so as to remove the static dependency
created by the previous changesets.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
newer versions of the xc5000 silicon require newer firmware
while remaining 100% driver compatible. original versions
of the xc5000a continue to use the same firmware.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Problems with the PID setting stalling demux on applications like VDR and MythTV.
The PID filter is now defaulted to OFF.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 7e07222 breaks DVBFE_ALGO_HW tuning after a retune is requested,
which causes bad tuning on my TBS 6920.
[ 0.769091] pci 0000:06:00.0: [14f1:8852] type 0 class 0x000400
[ 19.733530] CORE cx23885[0]: subsystem: 6920:8888, board: TurboSight TBS 6920 [card=14,autodetected]
[ 762.824912] cx24116_load_firmware: FW version 1.23.86.1
7e0722215a [media] dvb-core: Don't pass DVBv3 parameters on tune() fops
Although re_tune is set to true when FESTATE_RETUNE occurs, it is never
set back to false which the old code used to do when !FESTATE_RETUNE.
This patch sets re_tune to false if !(state & FESTATE_RETUNE).
$ szap-s2 -a 2 "Channel 5"
reading channels from file '/home/simon/.szap/channels.conf'
zapping to 247 'Channel 5':
delivery DVB-S, modulation QPSK
sat 0, frequency 10964 MHz H, symbolrate 22000000, coderate 5/6, rolloff 0.35
vpid 0x092a, apid 0x092b, sid 0x092d
using '/dev/dvb/adapter2/frontend0' and '/dev/dvb/adapter2/demux0'
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eb33 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware (up to two cards) and the Keene USB FM Transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware and the Keene USB FM Transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware and the Keene USB FM Transmitter.
Improved the volume handling delays through trial and error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have quite a few ISA radio drivers, which are all very similar.
This framework makes it possible to reduce the code size of those drivers
and makes it much easier to keep them up to date with the latest V4L2 API
developments.
Drivers rewritten to use this framework fully pass the v4l2-compliance tests
and are properly using the ISA bus (so they can be found under /sys/bus/isa).
It is now also possible to support multiple cards using the same driver
(tested with two radio-gemtek cards).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for different types of remote.
ITE remotes share common device IDs with differently assigned keys.
Two versions of remote maps have been created there are likely to be more.
v1 for all other IDs
v2 for USB_PID_ITETECH_IT9135_9005.
This patch also separates the configuration parts from it913x_identify_state function.
TODO
remotes for HID interfaces.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
status has to be set to STREAMING before the streaming worker is
queued. hdpvr_transmit_buffers() will exit immediately otherwise.
Reported-by: Joerg Desch <vvd.joede@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many drivers just support control events, and most radio drivers just need
to poll for control events. Add some functions to simplify those jobs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the start and end messages for log_status when called from a
subdev device node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For drivers that properly use the v4l2 framework (i.e. set v4l2_dev in the
video_device struct), the start and end messages of VIDIOC_LOG_STATUS are
now generated automatically. People tended to forget these, but the v4l2-ctl
tool scans for these messages, and it also makes it easier to read the status
output in the kernel log.
The cx18, ivtv and bttv drivers were changed since they no longer need to
log these start/end messages.
In saa7164 two empty log_status functions were removed.
Also added a helper function to v4l2-ctrl.c that can be used as the
vidioc_log_status callback if all you need to do is to log the current control
values. This is now used by pwc and vivi.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this private ioctl it is possible to use the ivtv decoder without
requiring the dvb/video.h and dvb/audio.h headers.
Eventually support for those DVB APIs will be dropped from ivtv.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx18 and ddbridge drivers include linux/dvb/audio.h and video.h
without using them.
Remove those includes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As discussed during the 2011 V4L-DVB workshop we want to create a proper V4L2
decoder API that replaces the DVBv5 API that has been used until now.
This adds the four controls necessary to be able to switch ivtv over to this
new API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As discussed during the 2011 V4L-DVB workshop, the API in dvb/video.h should
be replaced by a proper V4L2 API. This patch turns the VIDEO_(TRY_)DECODER_CMD
ioctls into proper V4L2 ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for some -Wuninitialized compiler warnings.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In tm6000_ir_fini() there seems to be a problem.
rc_unregister_device(ir->rc); calls rc_free_device() on the pointer it is
given, which frees it.
Subsequently the function does:
if (!ir->polling)
__tm6000_ir_int_stop(ir->rc);
and __tm6000_ir_int_stop() dereferences the pointer it is given, which
has already been freed.
and it also does:
tm6000_ir_stop(ir->rc);
which also dereferences the (already freed) pointer.
So, it seems that the call to rc_unregister_device() should be move
below the calls to __tm6000_ir_int_stop() and tm6000_ir_stop(), so
those don't operate on a already freed pointer.
But, I must admit that I don't know this code *at all*, so someone who
knows the code should take a careful look before applying this
patch. It is based purely on inspection of facts of what is beeing
freed where and not at all on understanding what the code does or why.
I don't even have a means to test it, so beyond testing that the
change compiles it has seen no testing what-so-ever.
Anyway, here's a proposed patch.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some version 2 devices have different tuner IDs. ID 0x38
appears to have weak signal strength.
Apply default 0x60 to unknown IDs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase mt2063 frequency_max to tune to channel 69(858Mhz).
Jose Alberto
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove unnecessary inclusion of machine specific header files mach/dm646x.h,
mach/hardware.h from vpif.h and aslo mach/dm646x.h from vpif_display.c
driver which comes in the way of platform code consolidation.
Add linux/i2c.h header file in vpif_types.h which is required for
building.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: LMML <linux-media@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is just a minor update to one titled "imon: Input from ffdc
device type ignored" from Corinna Vinschen. An earlier patch to prevent
an oops when we got early callbacks also has the nasty side-effect of
wedging imon hardware, as we don't acknowledge the urb. Rework the check
slightly here to bypass processing the packet, as the driver isn't yet
fully initialized, but still acknowlege the urb and submit a new rx_urb.
Do this for both interfaces -- irrelevant for ffdc hardware, but
relevant for newer hardware, though newer hardware doesn't spew the
constant stream of data as soon as the hardware is initialized like the
older ffdc devices, so they'd be less likely to trigger this anyway...
Tested with both an ffdc device and an 0042 device.
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_CAP_DEVICE_CAPS is valid for the capabilities field only as per
the spec.
Found with v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control message load increased heavily after CI/CAM support due
to dvb_ca_en50221. It looks like CI/CAM drops to non-working
state easily after error is returned to its callbacks. Due to
that, add some logic to avoid errors repeating failed messages.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As part of the removal of get_driver()/put_driver(), this patch
(as1510) changes driver_find(); it now drops the reference it acquires
before returning. The patch also adjusts all the callers of
driver_find() to remove the now unnecessary calls to put_driver().
In addition, the patch adds a warning to driver_find(): Callers must
make sure the driver they are searching for does not get unloaded
while they are using it. This has always been the case; driver_find()
has never prevented a driver from being unregistered or unloaded.
Hence the patch will not introduce any new bugs. The existing callers
all seem to be okay in this respect, however I don't understand the
video drivers well enough to be certain about them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: Andy Walls <awalls@md.metrocast.net>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix bug introduced by multi-frontend to single-frontend change.
It is safer to put DVB-T parts sleeping when auto-switching to DVB-T2
and vice versa. That was original behaviour.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No more error that error seen when device is plugged:
dvb_ca adapter 0: Invalid PC card inserted :(
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced by multi-frontend to single-frontend change.
This parameter is no longer used after multi-frontend to single-frontend change.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced by multi-frontend to single-frontend change.
* Add missing DVB-C caps
* Change frontend name as single frontend does all the standards
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As recommended by Jason at ITE, the chip version should select firmware.
However, to continue to support IT9137 firmware with different configuration
the driver will use udev->descriptor.idVendor to select the difference
between IT9135 and IT9137.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If V4L2_CAP_DEVICE_CAPS is set, then the new device_caps field is filled with
the capabilities of the opened device node.
The capabilities field traditionally contains the capabilities of the physical
device, being a superset of all capabilities available at the several device
nodes. E.g., if you open /dev/video0, then if it contains VBI caps then that means
that there is a corresponding vbi node as well. And the capabilities field of
both the video and vbi nodes should contain identical caps.
However, it would be very useful to also have a capabilities field that contains
just the caps for the currently open device, hence the new CAP bit and field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following warning by using platform_driver_probe() instead of
platform_driver_register():
WARNING: drivers/media/video/omap/omap-vout.o(.data+0x24): Section
mismatch in reference from the variable omap_vout_driver to the function
.init.text:omap_vout_probe()
The variable omap_vout_driver references
the function __init omap_vout_probe()
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3-rc1': (8187 commits)
Linux 3.3-rc1
x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
qnx4: don't leak ->BitMap on late failure exits
qnx4: reduce the insane nesting in qnx4_checkroot()
qnx4: di_fname is an array, for crying out loud...
KEYS: Permit key_serial() to be called with a const key pointer
keys: fix user_defined key sparse messages
ima: fix cred sparse warning
uml: fix compile for x86-64
MPILIB: Add a missing ENOMEM check
tpm: fix (ACPI S3) suspend regression
nvme: fix merge error due to change of 'make_request_fn' fn type
xen: using EXPORT_SYMBOL requires including export.h
gpio: tps65910: Use correct offset for gpio initialization
acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
intel_idle: Split up and provide per CPU initialization func
ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
...
USB data transfers may not work if the buffer is allocated at
the stack. Be sure to use kmalloc on all places where a buffer
is needed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several changes were needed to make az6007 to work, producing
the same commands as the original driver. This patch does
that.
While here, be less verbose when debug is not enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver were written to use a previous solution for MFE at dvb-usb.
Due to the internal API changes, change the binding to work with the
new way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code still needs to be commented, as there's a mutex
missing at the az6007_read() call. A mutex there is needed,
in order to prevent RC (or CI) calls while other operations
are in progress.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces no functional changes. It basically defines
a macro for each different req found at the driver, and cleans the
code to use them, making easier to understand the code.
With regards to the IR handling code, although the original code
doesn't define what's the request, it is clear, from the USB logs,
that 0xc5 is for IR polling.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use usb_device for those routines, as it allows using them on
all places. While there, rename to better express the meaning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the ngene/ddbridge firmware into their drivers.
There are two reasons for that:
1) The firmware used there didn't work for a few devices
I tested here (Terratec H5, H6 and H7);
2) At least Terratec H7 doesn't seem to require a firmware
for it to work.
After this change, if firmware is not specified, the driver will
use a rom-based firmware (this seems to be the case for Terratec
H7, although I need to better check the USB dumps to be sure about
that).
In any case, the firmware seems to be optional, as the DRX-K driver
don't return the firmware load error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mutex is there to protect the I2C gate. However, for some reason,
it is being called twice:
[ 2103.542796] usbcore: registered new interface driver dvb_usb_az6007
[ 2103.772392] az6007: drxk_gate_ctrl: enable
[ 2103.793900] az6007: drxk_gate_ctrl: enable
For now, let's just comment, to allow the driver to run.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mt2063 uses a one-byte transfer. This requires a special handling
inside the i2c code. Fix it to properly accept i2c reads. This
is needed to make the mt2063 to be detected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some fixes to allow frontend attachment. The patch is not
complete yet, as just the frontend 0 is initialized. So, more
changes will be needed, including some changes at dvb-usb core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes are needed, in order to make az6007 compile with the
upstream tree. Most of the changes are due to the upstream drxk
module.
Even allowing its compilation, the driver is not working yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Import the az6007 driver from Terratec H7 source, as-is.
It won't compile or run, so latter patches are needed in order
to fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (57 commits)
[media] as3645a: Fix compilation by including slab.h
[media] s5p-fimc: Remove linux/version.h include from fimc-mdevice.c
[media] s5p-mfc: Remove linux/version.h include from s5p_mfc.c
[media] ds3000: using logical && instead of bitwise &
[media] v4l2-ctrls: make control names consistent
[media] DVB: dib0700, add support for Nova-TD LEDs
[media] DVB: dib0700, add corrected Nova-TD frontend_attach
[media] DVB: dib0700, separate stk7070pd initialization
[media] DVB: dib0700, move Nova-TD Stick to a separate set
[media] : add MODULE_FIRMWARE to dib0700
[media] DVB-CORE: remove superfluous DTV_CMDs
[media] s5p-jpeg: adapt to recent videobuf2 changes
[media] s5p-g2d: fixed a bug in controls setting function
[media] s5p-mfc: Fix volatile controls setup
[media] drivers/media/video/s5p-mfc/s5p_mfc.c: adjust double test
[media] drivers/media/video/s5p-fimc/fimc-capture.c: adjust double test
[media] s5p-fimc: Fix incorrect control ID assignment
[media] dvb_frontend: Don't call get_frontend() if idle
[media] DocBook/dvbproperty.xml: Remove DTV_MODULATION from ISDB-T
[media] DocBook/dvbproperty.xml: Fix ISDB-T delivery system parameters
...
The intent here was to test if the FE_HAS_LOCK was set. The current
test is equivalent to "if (status) { ..."
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several control names used inconsistent capitalization or were inconsistent
in other ways. I also corrected a spelling mistake and fixed four strings
that were too long (>31 characters). Harmless, but the string is cut off when
it is returned with QUERYCTRL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an override of read_status to intercept lock status. This allows
us to switch LEDs appropriately on and off with signal un/locked.
The second phase is to override sleep to properly turn off both.
This is a hackish way to achieve that.
Thanks to Mike Krufky for his help.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This means cut & paste from the former f. attach. But while at it write
to the right GPIO to turn on the right LED. Also turn the other two
off jsut for sure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The start is common for both stk7070pd and novatd specific routine.
This is just a preparation for the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To properly support the three LEDs which are on the stick, we need
a special handling in the ->frontend_attach function. Thus let's have
a separate ->frontend_attach instead of ifs in the common one.
The hadnling itself will be added in further patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dib0700 needs a binary firmware file. This patch added the MODULE_FIRMWARE-macro.
Signed-off-by: Christoph Anton Mitterer <calestyo@scientia.net>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This small patch removes superfluous DTV_CMDs from dvb_frontend.c which were added in the initially when ISBD-T support was added.
They were there unnoticed even though compilers should have warning about those duplicates. Finally they did and now we can remove them.
Thanks to Dan Carpenter <dan.carpenter@oracle.com> for pointing that out.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
queue_setup callback has been extended with struct v4l2_format *fmt
parameter in 2d86401c2c commit. This patch adds this parameter to
s5p-jpeg driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the mismatch between control IDs (CID) and controls
for hflip, vflip and rotate.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the frontend is in idle state, don't call get_frontend.
Calling get_frontend() when the device is not tuned may
result in wrong parameters to be returned to the
userspace.
I was tempted to not call get_frontend() at all, except
inside the dvb frontend thread, but this won't work for
all cases. The ISDB-T specs (ABNT NBR 15601 and ARIB
STD-B31) allow the broadcaster to dynamically change the
channel specs at runtime. That means that an ISDB-T optimized
application may want/need to monitor the TMCC tables, decoded
at the frontends via get_frontend call.
So, let's do the simpler change here.
Eventually, the logic could be changed to work only if
the device is tuned and has lock, but, even so, the
lock is also standard-dependent. For ISDB-T, the right
lock to wait is that the demod has TMCC lock. So, drivers
may need to implement some logic to detect if the get_frontend
info was retrieved or not.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes bug introduced by multi-frontend to single-frontend change.
Finally HAS_LOCK is got back!
We are not allowed to access hardware in sleep mode...
Chip did not like when .get_frontend() reads some registers while
chip was sleeping and due to that HAS_LOCK bit was never gained.
TODO: We should add logic for dvb-core to drop out illegal calls like that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix yet another bug introduced be recent cxd2820r multi-frontend to
single-frontend change.
Finally, we have at least almost working picture for DVB-C too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As pointed out by 'make versioncheck', there's no need for
drivers/media/dvb/frontends/tda18271c2dd.c to
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix another bug introduced by recent multi-frontend to single-frontend
change.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cxd2820r implements only one frontend currently which
handles all the standards.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The caller doesn't check the return value of check_firmware() but static
checkers complain. It currently returns negative error codes, or zero
or greater on success but since the return type is boolean the values
are truncated to one or zero. I've changed it to return an int,
negative on error and zero on success.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These were initialized twice by mistake. They were defined the same way
both times so this doesn't change how the code works.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In xc4000 chipsets real signal and noise level is stored in register
0x0A and 0x0B,so we can use those registers to monitor signal strength.
I tested this patch on 2 different cards Leadtek DVR3200 and DTV2000H
Plus, both with same results, I used special antenna hubs (toner 4x, 6x,
8x and 12x) with mesured signal lost, both registers are in dB value,
first represent signal with limit value -113.5dB (should be -114dB) and
exactly match with test results. Second represents noise level also in
dB and there is no maximum value, but from tests we can drop everything
above 32dB which tuner realy can't use, signal was usable till 20dB
noise level.
In digital mode we can take signal strength but sadly noise level is not
relevant and real value is stored in demodulator for now just zl10353,
also digital mode is just for testing, because it needs changing other
parts of code which reads data only from demodulator.
In analog mode I was able to test only FM radio, signal level is not
important, it says something about cable and hub losts, but nothing
about real quality of reception, so even if we have signal level at
minimum 113dB we can still here radio, because of that it is displaied
only in debug mode, but for real signal level is used noise register
which is again very accurate, radio noise level was betwen 6-20dB for
good signal, 20-25dB for medium signal, and above 25dB signal is
unusable.
For now real benefit of this patch is only for FM radio mode.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All radio tuners in cx88 driver using same address for radio and tuner,
so there is no need to probe it twice for same tuner and we can use
radio_type UNSET, this also fix broken radio since kernel 2.6.39-rc1
for those tuners.
Cc: stable@kernel.org
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All radio tuners in cx23885 driver using same address for radio and
tuner, so there is no need to probe it twice for same tuner and we can
use radio_type UNSET.
Be aware radio support in cx23885 is not yet committed, so this is only
minor fix for future support.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"dev" is NULL here so we should use "nr" instead of "dev->devno".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clearly ">=" was intended here instead of ">".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reduces our module init to a simple usb_register() call, so
that we can make use of the new upcoming macro's for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code for this is rather crufty, and being able to tie a device
to a specific minor is not really something we want to support in
a modern udev based world.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pwc driver used to:
1. kmalloc a buffer
2. memcpy data to send over usb there
3. do the usb_control_msg call (which does not work with data on the stack)
4. free the buffer
For every usb command send. This patch changes the code to instead malloc
a buffer for this purpose once and use it everywhere.
[mchehab@redhat.com: Fix a compilation breakage with allyesconfig:
drivers/media/video/pwc/pwc-ctrl.c: In function ‘pwc_get_cmos_sensor’:
drivers/media/video/pwc/pwc-ctrl.c:546:3: warning: passing argument 4 of ‘recv_control_msg’ makes integer from pointer without a cast [en$
drivers/media/video/pwc/pwc-ctrl.c:107:12: note: expected ‘int’ but argument is of type ‘unsigned char *’
drivers/media/video/pwc/pwc-ctrl.c:546:3: error: too many arguments to function ‘recv_control_msg’
drivers/media/video/pwc/pwc-ctrl.c:107:12: note: declared here]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we always do a set_video_mode on stream start, there is no need
to actually send the mode info to the device on a s_fmt / s_parm ioctl.
Not doing this saves us doing (slow) usb io.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch various code in the mode setting patch checked
pdev->pixfmt, but that was not set until the mode setting succeeded, so
it was looking at the old pixfmt! This patch fixes this by making the
pixfmt a parameter to set_video_mode, and setting it from set_video_mode
on success.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of messing around with id's it's much easier to just compare
against a filehandle pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason the cx18 driver could open the radio device only once.
Remove this limitation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason the /dev/radio device was implemented as an exclusive open:
you could open it only once and not a second time.
Remove this limitation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As per the feature removal document, make the tuner type check more strict
so that it is no longer possible to set the radio frequency through a video
node or the TV frequency through a radio node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The omap_vout driver has an output overlay, but never advertised that
capability.
The driver should also set the V4L2_FBUF_FLAG_OVERLAY flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: Archit Taneja <archit@ti.com>
CC: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zoran driver does not support this flag, so don't set it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error handling in the original code wasn't complete so static
checkers complained about a potential NULL deference.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (655 commits)
[media] revert patch: HDIC HD29L2 DMB-TH USB2.0 reference design driver
mb86a20s: Add a few more register settings at the init seq
mb86a20s: Group registers into the same line
[media] [PATCH] don't reset the delivery system on DTV_CLEAR
[media] [BUG] it913x-fe fix typo error making SNR levels unstable
[media] cx23885: Query the CX25840 during enum_input for status
[media] cx25840: Add support for g_input_status
[media] rc-videomate-m1f.c Rename to match remote controler name
[media] drivers: media: au0828: Fix dependency for VIDEO_AU0828
[media] convert drivers/media/* to use module_platform_driver()
[media] drivers: video: cx231xx: Fix dependency for VIDEO_CX231XX_DVB
[media] Exynos4 JPEG codec v4l2 driver
[media] doc: v4l: selection: choose pixels as units for selection rectangles
[media] v4l: s5p-tv: mixer: fix setup of VP scaling
[media] v4l: s5p-tv: mixer: add support for selection API
[media] v4l: emulate old crop API using extended crop/compose API
[media] doc: v4l: add documentation for selection API
[media] doc: v4l: add binary images for selection API
[media] v4l: add support for selection api
[media] hd29l2: fix review findings
...
The changeset 240ab508aa is incomplete, as the first thing that
happens at cache clear is to do a memset with 0 to the cache.
So, the delivery system needs to be explicitly preserved there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I added it by mistake. It is useless as no real hardware.
It even uses even Cypress FX2, general USB bridge chip, default IDs
that makes driver load all FX2 devices having default ID...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Lawrence[1], MythTV 0.24.1 does the wrong thing
with a DVBv5 call: it fills the delivery system with
SYS_UNDEFINED, expecting that the DVB core would work with that.
This used to work by accident, as the DVB core were missing the
check for the supported delivery systems. Yet, fixing it
is easy, so let's add a logic to handle this case, to
provide backward compatibility.
[1] http://patchwork.linuxtv.org/patch/8314/
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
module_param_array(), unlike its non-array cousins, didn't check the type
of the variable. Fixing this found two bugs.
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: linux-media@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Some time ago, Manoel sent us a patch adding more stuff
to the init sequence. However, his patch were also doing
non-related stuff, by changing the init logic without
any good reason. So, it was asked for him to submit a
patch with just the data that has changed, in order to
allow us to better analyze it.
As he didn't what it was requested, I finally found some
time to dig into his init sequence and add it here.
Basically, new stuff is added there. There are a few changes:
1) The removal of the extra (duplicated) logic that puts
the chip into the serial mode;
2) Some Viterbi VBER measurement init data was changed from
0x00 to 0xff for layer A, to match what was done for
layers B and C.
None of those caused any regressions and both make sense
on my eyes.
The other parameters additions actually increased the
tuning quality for some channels. Yet, some channels that
were previously discovered with scan disappered, while
others appeared instead. This were tested in Brasilia,
with an external antena.
At the overall, it is now a little better. So, better to
add these, and then try to figure out a configuration that
would get even better scanning results.
Reported-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On mb86a20s, some registers have sub-addresses, while others not.
In order to make easier to compare different settings, group them.
No functional changes in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a DVBv3 application may be relying on the delivery system,
don't reset it at DTV_CLEAR. For DVBv5 applications, the
delivery system should be set anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We can pass a NO_SIGNAL video decoder state back to applications
if it's available.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This remote was added with support for card Compro VideoMate M1F.
This remote is shipped with various Compro cards, not this one only.
Furthermore this remote can be bought separately under name Compro
VideoMate K100.
http://compro.com.tw/en/product/k100/k100.html
So give it a proper name.
[mchehab@redhat.com: Fix the Makefile]
Signed-off-by: Samuel Rakitničan <samuel.rakitnican@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the drivers in drivers/media/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: "Richard Röjfors" <richard.rojfors@pelagicore.com>
Cc: "Matti J. Aaltonen" <matti.j.aaltonen@nokia.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Muralidharan Karicheri <m-karicheri2@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add driver for the JPEG codec IP block available in Samsung Exynos SoC series.
The driver is implemented as a V4L2 mem-to-mem device. It exposes two video
nodes to user space, one for the encoding part, and one for the decoding part.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adjusting of Video Processor's scaling factors was flawed. It bounded scaling
to range 1/16 to 1/1. The correct range should be 1/4 to 4/1. This patch fixes
this bug.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add support for V4L2 selection API to s5p-tv driver. Moreover it
removes old API for cropping. Old applications would still work because the
crop ioctls are emulated using the selection API.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch allows new video drivers to work correctly with applications that
use the old-style crop API. The old crop ioctl is emulated by using selection
callbacks.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces new api for a precise control of cropping and composing
features for video devices. The new ioctls are VIDIOC_S_SELECTION and
VIDIOC_G_SELECTION.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some issues pointed out by Mauro.
Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow use of that general callback for demod too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card definition of the Terratec Cinergy 200 USB uses the
wrong tuner type. Therefore some channels are currently missing.
Attached patch fixes this problem.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MaxPacketSize for em2800 based devices is too small to capture at full resolution.
Therefore scale down when the maximum frame size is selected.
The previous workaround that simply reduced the X resolution cannot be used
because it crops a part of the input as
the em2800 can only scale down with a factor of 0.5.
reverts commits 1ca31892e and fb3de0398a.
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
writing the EM28XX_R06_I2C_CLK register leads to the problem that the
i2c bus on the Terratec Cinergy 200 USB is no longer usable when the
system is rebooted.
The device needs to be unplugged in order to bring it back to life.
Attached patch conditionally disables the write in
em28xx_pre_card_setup() like it is already done in em28xx_card_setup().
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It looks like the return value check that is done after setting the I2C
speed checks the wrong return code.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'struct em28xx *' pointer was passed by reference to the
em28xx_init_dev() function, for no reason. Instead, just pass it by
value, which is much more logical and simple.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The af9005_properties and af9015_properties tables make use of USB ids
from the USB id tables with hardcoded indices, as in
"&af9015_usb_table[30]". Adding new entries before the end breaks
such references, so everyone has had to carefully tiptoe to only add
entries at the end of the list.
In the spirit of "dw2102: use symbolic names for dw2102_table
indices", use C99-style initializers with symbolic names for each
index to avoid this. In the new regime, properties tables referring
to the USB ids have names like "&af9015_usb_table[CINERGY_T_STICK_RC]"
that do not change meaning when items in the USB id table are
reordered.
Encouraged-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Acked-by: Luca Olivetti <luca@ventoso.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
URBs allocated with usb_alloc_urb() are allocated from DMA-coherent
areas, and therefore it is not necessary to call dma_map_single() on
such buffers. Worst, on ARM, calling dma_map_single() on a
DMA-coherent buffer will trigger a BUG_ON() in
arch/arm/mm/dma-mapping.c.
Therefore, we mark all URBs allocated with usb_alloc_urb() with the
URB_NO_TRANSFER_DMA_MAP transfer_flags, so that the USB core does not
do dma_map_single()/dma_unmap_single() on those buffers.
This is similar to 882787ff8f for the
gspca driver, and has already been discussed on the linux-media list
in the past:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg37086.html.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'struct cx231xx *' pointer was passed by reference to the
cx231xx_init_dev() function, for no reason. Instead, just pass it by
value, which is much more logical and simple.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVB-T did not work at all - only 6 MHz was working but it is not
commonly used.
Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver were using DEV_MISCONFIGURED on some places, and
DEV_DISCONNECTED on others. In a matter of fact, DEV_MISCONFIGURED
were set only during the usb disconnect callback, with
was confusing.
Also, the alsa driver never checks if the device is present,
before doing some dangerous things.
Remove DEV_MISCONFIGURED, replacing it by DEV_DISCONNECTED.
Also, fixes the other usecases for DEV_DISCONNECTED.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several weirdness at the unregister logic.
First of all, IR has a poll thread. This thread needs to be
removed, as it uses some resources associated to the main driver.
So, the driver needs to explicitly unregister the I2C client for
ir-kbd-i2c.
If, for some reason, the driver needs to wait for a close()
to happen, not all memories will be freed, because the free
logic were in the wrong place.
Also, v4l2_device_unregister() seems to be called too early,
as devices are still using it.
Finally, even with the device disconnected, there is one
USB function call that will still try to talk with it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the device got removed, stops polling it. Also, un-registers
it at input/evdev, as it won't work anymore. We can't free the
IR structure yet, as the ir_remove method will be called later.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we set the intfdata on the right interface, the 'lif'
variable is useless.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following sequence of commands was triggering a kernel crash in
cdev_get():
modprobe cx231xx
rmmod cx231xx
modprobe cx231xx
v4l2grab -n 1
The problem was that cx231xx_usb_disconnect() was not doing anything
because the test:
if (!dev->udev)
return;
was reached (i.e, dev->udev was NULL).
This is due to the fact that the 'dev' pointer placed as intfdata into
the usb_interface structure had the wrong value, because
cx231xx_probe() was doing the usb_set_intfdata() on the wrong
usb_interface structure. For some reason, cx231xx_probe() was doing
the following:
static int cx231xx_usb_probe(struct usb_interface *interface,
const struct usb_device_id *id)
{
struct usb_interface *lif = NULL;
[...]
/* store the current interface */
lif = interface;
[...]
/* store the interface 0 back */
lif = udev->actconfig->interface[0];
[...]
usb_set_intfdata(lif, dev);
[...]
retval = v4l2_device_register(&interface->dev, &dev->v4l2_dev);
[...]
}
So, the usb_set_intfdata() was done on udev->actconfig->interface[0]
and not on the 'interface' passed as argument to the ->probe() and
->disconnect() hooks. Later on, v4l2_device_register() was
initializing the intfdata of the correct usb_interface structure as a
pointer to the v4l2_device structure.
Upon unregistration, the ->disconnect() hook was getting the intfdata
of the usb_interface passed as argument... and casted it to a 'struct
cx231xx *' while it was in fact a 'struct v4l2_device *'.
The correct fix seems to just be to set the intfdata on the proper
interface from the beginning. Now, loading/unloading/reloading the
driver allows to use the device properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Toralf:
the build failed with :
CC [M] drivers/media/dvb/dvb-core/dvb_ca_en50221.o
In file included from arch/x86/include/asm/uaccess.h:573:0,
from include/linux/poll.h:14,
from drivers/media/dvb/dvb-core/dvbdev.h:27,
from drivers/media/dvb/dvb-core/dvb_ca_en50221.h:27,
from drivers/media/dvb/dvb-core/dvb_ca_en50221.c:41:
In function "copy_from_user", inlined from "dvb_ca_en50221_io_write" at drivers/media/dvb/dvb-core/dvb_ca_en50221.c:1314:26: arch/x86/include/asm/uaccess_32.h:211:26: error: call to "copy_from_user_overflow" declared with attribute error: copy_from_user() buffer size is not provably correct
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
I ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9q+1
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
The patch "dm1105: handle errors from dvb_net_init" moved the
initialization of dvbnet to before frontend attachment but forgot
to adjust the error handling when frontend attachment fails.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module does some printks with the loglevel missing.
pr_err() takes care of adding the KERN_ERR tag and the module name.
So we can simplify the code and add the missing printk loglevel by
using it.
Also add a #define pr_fmt() to make this work, and remove a few
unnecessary periods at the end of messages and bump the loglevel of
"Unknown bttv card type" from KERN_WARNING to KERN_ERR while at it.
Inspired-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This way, the messages will be tagged with KERN_DEBUG and not clutter
the log from dmesg unless the "debug" module parameter is set.
[mchehab@redhat.com: whitespace fixes]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code is wrong as I should have coded it as SYS_DVBC, instead of
SYS_DVBS & friends. Anyway, this check has other problems
1) it does some "magic" by assuming that all QAM modulations are below
QAM_AUTO;
2) it checks modulation parameters only for one delivery system.
Or the core should check invalid parameters for all delivery
systems, or it should let the frontend drivers do it;
3) frontend drivers should already be checking for invalid parameters
(most of them do it, anyway);
4) not all modulations are mapped at fe->ops.info.caps, so it is not
even possible to check for the valid modulations inside the core
for some delivery systems;
5) The core check is incomplete anyway: it only checks for a few
parameters. If moved into the core other parameters like bandwidth
and fec should also be checked;
6) 2nd gen DVB-C uses OFDM. So, that test would fail for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Oliver, some old dead code were preserved there.
Thanks-to: Oliver endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for two new types of Leadtek Winfast TV 2000XP tuner
The author of this patch is Istvan Varga.
Only resending current reformated version against current git.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If ctrls->count is too high the multiplication could overflow and
array_size would be lower than expected. Mauro and Hans Verkuil
suggested that we cap it at 1024. That comes from the maximum
number of controls with lots of room for expantion.
$ grep V4L2_CID include/linux/videodev2.h | wc -l
211
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Smatch complains that i can be one passed the end of the array if we
don't hit the break statement. We should be using the "audio" here like
we do in the other places.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is just a cleanup, it doesn't change how the code works. These
are compound conditions and not bitwise operations so it should be &&
and not &.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leadtek DTV2000H J has Philips a FMD1216MEX tuner,
and not a FMD1216ME.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces the previous one proposed in the thread "xc3028:
force reload of DTV7 firmware in VHF band with Zarlink demodulator",
at the linux-media@vger.kernel.org ML.
The problem is that the firmware DTV78 works fine in UHF band (8 MHz
bandwidth) but is not working at all in VHF band (7 MHz bandwidth).
Reading the comments inside the code, I figured out that the real
problem could be connected to the formula used to calculate the center
frequency offset in VHF band.
In fact, removing this adjustment fixes the problem:
if ((priv->cur_fw.type & DTV78) && freq < 470000000)
offset -= 500000;
This is coherent to what was implemented for the DTV7 firmware by an
Australian user:
if (priv->cur_fw.type & DTV7)
offset += 500000;
In the end, now the center frequency is the same for all firmwares
(DTV7, DTV8, DTV78) and doesn't depend on channel bandwidth.
The final code looks clean and simple, and there is no need for any
"magic" adjustment:
if (priv->cur_fw.type & DTV6)
offset = 1750000;
else /* DTV7 or DTV8 or DTV78 */
offset = 2750000;
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following build warning:
warning: (RADIO_WL128X) selects TI_ST which has unmet direct dependencies (MISC_DEVICES && NET && GPIOLIB)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Thu, 2011-12-15 at 16:42 +0000, Malcolm Priestley wrote:
> > [ 1103.536156] it913x: Chip Version=ec Chip Type=5830
> > [ 1104.336178] it913x: Dual mode=92 Remote=92 Tuner Type=92
> > [ 1106.248116] dvb-usb: found a 'ITE 9135(9006) Generic' in cold state,
> > will try to load a firmware
> > [ 1106.253773] dvb-usb: downloading firmware from file
> > 'dvb-usb-it9135-02.fw'
> > [ 1106.452123] it913x: FRM Starting Firmware Download
> > [ 1130.756039] it913x: FRM Firmware Download Failed (ffffff92)
> > [ 1130.956168] it913x: Chip Version=79 Chip Type=5823
> > [ 1131.592192] it913x: DEV it913x Error
> > [ 1131.592271] usbcore: registered new interface driver it913x
> >
> > No frontend is generated anyway.
>
> Looks like the the firmware is not at all compatible with your device.
>
> Have you applied the patch cleanly to the latest media_build?
>
> These appear to be new version of the 9006. A supplier is sending me one
> of these devices.
>
> As a last resort see if the device works with dvb-usb-it9137-01.fw
>
> You will have force to use this firmware
> dvb-usb-it913x firmware=1
Here is a modified firmware loader for version 2 types.
The firmware must be as in original
./dvb_get_firmware it9135
dd if=dvb-usb-it9135.fw ibs=1 skip=12866 count=5817 of=dvb-usb-it9135-02.fw
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes an obvious typo in the get_frontend() function
of the af9013 driver, recently rewritten by Antti Palosaari.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correction to tuner ID 0x51.
Don't force tuner ID 0x60 unless eprom data zero.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for the Plextor ConvertX PX-AV100U, which uses the
eMPIA EM2820 chip. The device has a device_id of '0x093b, 0xa003'. I
am using the existing EM2820_BOARD_PINNACLE_DVC_90 board profile, as
the Pinnacle Dazzle DVC 90/100/101/107, Kaiser Baas Video to DVD
maker, and Kworld DVD Maker 2 were already mapped to it. Some more
background on the device and my testing can be found at
http://www.donkramer.net/plextor_122710.pdf
Signed-off-by: Don Kramer <dgkramer@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some channels appear weak signal after warm boot.
Because tuner id is not present in eprom 0x38 is
assigned.
9006 devices are now always assigned 0x60.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes issues with PID filter
Stalling of some channels when PID is on.
PID filter not turning off fully.
PID filter can now turn on and off each index.
Removed PID_RST from it913x_pid_filter_ctrl.
Replaced with PID_EN removed from it913x_pid_filter
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_LOG_STATUS ioctl allows to dump the current status of a driver
to the kernel log. Currently this ioctl is only available at video device
nodes and the subdevs rely on the host driver to expose their core.log_status
operation to user space.
This patch adds VIDIOC_LOG_STATUS support at the sub-device nodes,
for standalone subdevs that expose their own /dev entry.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following ioctl sequence causes fimc_dma_run() to start processing without
complete scaler and DMA initialization which causes missing interrupt and
blocking on DQBUF:
S_FMT, STREAMON, QBUF, DQBUF, STREAMOFF, STREAMON, QBUF, DQBUF.
Fix this regression caused by moving pm_runtime* calls to start/stop_streaming
callback by making sure the fimc_m2m_resume() is always invoked when expected.
Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not common for dvb_net_init to fail, but after the patch
"dvb_net_init: return -errno on error" it can fail due to running out
of memory. Handle this.
From an audit of dvb_net_init callers.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From an audit of dvb_net_init callers, now that that function
returns -errno on error.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
