Commit Graph

547 Commits

Author SHA1 Message Date
Bjorn Helgaas
eab3a0ee34 PCI: Preserve BIOS PCI_COMMAND_SERR and PCI_COMMAND_PARITY settings
Do not clear PCI_COMMAND_SERR or PCI_COMMAND_PARITY based on _HPP.  The
spec (ACPI rev 5.0, sec 6.2.7) says that when "Enable SERR" is set to 1,
we should enable SERR in the command register.  It says nothing about
*disabling* SERR or PERR; in fact, the example in 6.2.7.1 says we should
leave PERR alone unless "Enable PERR" is 1.

For hot-added devices, this probably doesn't matter because they power up
with these bits cleared.  But in addition to hot-plugged devices, the spec
allows the platform to use _HPP for "configuration of PCI devices not
configured by the BIOS at system boot," and it may make a difference for
devices present at boot.

This change means that if BIOS enables SERR or PERR on a device, and it
supplies _HPP or _HPX with the SERR or PERR bits *cleared*, we will now
leave SERR or PERR reporting enabled on that device instead of disabling it
as we previously did.

See also 40abb96c51 ("pciehp: Fix programming hotplug parameters"), where
this code was first added.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
2014-09-12 20:10:57 -06:00
Bjorn Helgaas
c6285fc5b5 PCI: Apply _HPP settings to PCIe devices as well as PCI and PCI-X
The ACPI _HPP method was defined before PCIe existed, so its documentation
only mentions PCI.  The _HPX Type 0 setting record is essentially identical
to _HPP, but the spec (ACPI rev 5.0, sec 6.2.8.1) says it should be applied
to PCI, PCI-X, and PCIe devices, with settings being ignored if they are
not applicable.

Some platforms with both conventional PCI and PCIe devices provide only
_HPP (not _HPX), so treat _HPP the same way as an _HPX Type 0 record and
apply it to PCIe devices as well as PCI and PCI-X.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
2014-09-12 20:10:16 -06:00
Bjorn Helgaas
fbfa398b84 PCI: Remove unused pci_configure_slot()
All pci_configure_slot() uses have been removed, so remove the definition
as well.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
2014-09-12 20:09:52 -06:00
Bjorn Helgaas
6cd33649fa PCI: Add pci_configure_device() during enumeration
Some platforms can tell the OS how to configure PCI devices, e.g., how to
set cache line size, error reporting enables, etc.  ACPI defines _HPP and
_HPX methods for this purpose.

This configuration was previously done by some of the hotplug drivers using
pci_configure_slot().  But not all hotplug drivers did this, and per the
spec (ACPI rev 5.0, sec 6.2.7), we can also do it for "devices not
configured by the BIOS at system boot."

Move this configuration into the PCI core by adding pci_configure_device()
and calling it from pci_device_add(), so we do this for all devices as we
enumerate them.

This is based on pci_configure_slot(), which is used by hotplug drivers.
I omitted:

  - pcie_bus_configure_settings() because it configures MPS and MRRS, which
    requires global knowledge of the fabric and must be done later, and

  - configuration of subordinate devices; that will happen when we call
    pci_device_add() for those devices.

Because pci_configure_slot() was only done by hotplug drivers, this initial
version of pci_configure_device() only configures hot-added devices,
ignoring anything added during boot.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
2014-09-12 20:09:46 -06:00
Bjorn Helgaas
589fcc2307 PCI: Move pci_configure_slot() to drivers/pci/probe.c
Move pci_configure_slot() and related functions from
drivers/pci/hotplug/pcihp_slot to drivers/pci/probe.c.

This is to prepare for doing device configuration during the normal
enumeration process instead of just after hot-add.

No functional change.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-09-12 20:02:00 -06:00
Rajat Jain
f3dbd802b3 PCI: Enable CRS Software Visibility for root port if it is supported
Per PCIe r3.0, sec 2.3.2, an endpoint may respond to a Configuration
Request with a Completion with Configuration Request Retry Status (CRS).
This terminates the Configuration Request.

When the CRS Software Visibility feature is disabled (as it is by default),
a Root Complex must handle a CRS Completion by re-issuing the Configuration
Request.  This is invisible to software.  From the CPU's point of view, an
endpoint that always responds with CRS causes a hang because the Root
Complex never supplies data to complete the CPU read.

When CRS Software Visibility is enabled, a Root Complex that receives a CRS
Completion for a read of the Vendor ID must return data of 0x0001.  The
Vendor ID of 0x0001 indicates to software that the endpoint is not ready.

We now have more devices that require CRS Software Visibility.  For
example, a PLX 8713 NT bridge may respond with CRS until it has been
configured via I2C, and the I2C configuration is completely independent of
PCI enumeration.

Enable CRS Software Visibility if it is supported.  This allows a system
with such a device to work (though the PCI core times out waiting for it to
become ready, and we have to rescan the bus after it is ready).

This essentially reverts ad7edfe049 ("[PCI] Do not enable CRS Software
Visibility by default").  The failures that led to ad7edfe049 should be
addressed by 89665a6a71 ("PCI: Check only the Vendor ID to identify
Configuration Request Retry").

[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/20071029061532.5d10dfc6@snowcone
Link: http://lkml.kernel.org/r/alpine.LFD.0.9999.0712271023090.21557@woody.linux-foundation.org
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-09-08 23:29:21 -06:00
Rajat Jain
89665a6a71 PCI: Check only the Vendor ID to identify Configuration Request Retry
Per PCIe r3.0, sec 2.3.2, if a Root Complex

  - has Configuration Request Retry Status Software Visibility enabled,
  - issues a Configuration Read of both bytes of the Vendor ID, and
  - receives a Completion with Configuration Request Retry Status (CRS),

it must complete the request to the host by fabricating data of 0x0001 for
the Vendor ID and 0xff for any additional bytes in the request.

Linux issues a single config read for the four bytes containing the Vendor
ID and the Device ID.  Previously we checked all four bytes for 0xffff0001
to identify CRS.

However, it is only the Vendor ID that really indicates CRS, because it's
sufficient to read only those two bytes.  Checking the Device ID verifies
spec compliance but doesn't add any information.

Some Root Complexes appear to indicate CRS by returning 0x0001 for the
Vendor ID along with the actual the Device ID.  Previously we interpreted
that as a valid Vendor/Device ID pair, although 0x0001 is reserved and
cannot be a valid Vendor ID.

[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/4729FC36.3040000@gmail.com
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-09-08 23:05:00 -06:00
Ryan Desfosses
227f064705 PCI: Merge multi-line quoted strings
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.

No functional change.

[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-06-10 20:20:42 -06:00
Ryan Desfosses
3c78bc61f5 PCI: Whitespace cleanup
Fix various whitespace errors.

No functional change.

[bhelgaas: fix other similar problems]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-06-10 20:20:19 -06:00
Ryan Desfosses
b7fe943421 PCI: Move EXPORT_SYMBOL so it immediately follows function/variable
Move EXPORT_SYMBOL so it immediately follows the function or variable.

No functional change.

[bhelgaas: squash similar changes, fix hotplug, probe, rom, search, too]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-06-10 13:36:10 -06:00
Bjorn Helgaas
fdaf36bd36 Merge branch 'pci/misc' into next
* pci/misc:
  PCI: Fix return value from pci_user_{read,write}_config_*()
  PCI: Turn pcibios_penalize_isa_irq() into a weak function
  PCI: Test for std config alias when testing extended config space
2014-05-28 16:21:25 -06:00
Bjorn Helgaas
d1a2523d2a Merge branches 'pci/hotplug', 'pci/pci_is_bridge' and 'pci/virtualization' into next
* pci/hotplug:
  PCI: cpqphp: Fix possible null pointer dereference
  NVMe: Implement PCIe reset notification callback
  PCI: Notify driver before and after device reset

* pci/pci_is_bridge:
  pcmcia: Use pci_is_bridge() to simplify code
  PCI: pciehp: Use pci_is_bridge() to simplify code
  PCI: acpiphp: Use pci_is_bridge() to simplify code
  PCI: cpcihp: Use pci_is_bridge() to simplify code
  PCI: shpchp: Use pci_is_bridge() to simplify code
  PCI: rpaphp: Use pci_is_bridge() to simplify code
  sparc/PCI: Use pci_is_bridge() to simplify code
  powerpc/PCI: Use pci_is_bridge() to simplify code
  ia64/PCI: Use pci_is_bridge() to simplify code
  x86/PCI: Use pci_is_bridge() to simplify code
  PCI: Use pci_is_bridge() to simplify code
  PCI: Add new pci_is_bridge() interface
  PCI: Rename pci_is_bridge() to pci_has_subordinate()

* pci/virtualization:
  PCI: Introduce new device binding path using pci_dev.driver_override

Conflicts:
	drivers/pci/pci-sysfs.c
2014-05-28 16:21:07 -06:00
Alex Williamson
782a985d7a PCI: Introduce new device binding path using pci_dev.driver_override
The driver_override field allows us to specify the driver for a device
rather than relying on the driver to provide a positive match of the
device.  This shortcuts the existing process of looking up the vendor and
device ID, adding them to the driver new_id, binding the device, then
removing the ID, but it also provides a couple advantages.

First, the above existing process allows the driver to bind to any device
matching the new_id for the window where it's enabled.  This is often not
desired, such as the case of trying to bind a single device to a meta
driver like pci-stub or vfio-pci.  Using driver_override we can do this
deterministically using:

  echo pci-stub > /sys/bus/pci/devices/0000:03:00.0/driver_override
  echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
  echo 0000:03:00.0 > /sys/bus/pci/drivers_probe

Previously we could not invoke drivers_probe after adding a device to
new_id for a driver as we get non-deterministic behavior whether the driver
we intend or the standard driver will claim the device.  Now it becomes a
deterministic process, only the driver matching driver_override will probe
the device.

To return the device to the standard driver, we simply clear the
driver_override and reprobe the device:

  echo > /sys/bus/pci/devices/0000:03:00.0/driver_override
  echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
  echo 0000:03:00.0 > /sys/bus/pci/drivers_probe

Another advantage to this approach is that we can specify a driver override
to force a specific binding or prevent any binding.  For instance when an
IOMMU group is exposed to userspace through VFIO we require that all
devices within that group are owned by VFIO.  However, devices can be
hot-added into an IOMMU group, in which case we want to prevent the device
from binding to any driver (override driver = "none") or perhaps have it
automatically bind to vfio-pci.  With driver_override it's a simple matter
for this field to be set internally when the device is first discovered to
prevent driver matches.

Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-05-28 16:04:53 -06:00
Alex Williamson
78916b00f0 PCI: Test for std config alias when testing extended config space
When a PCI-to-PCIe bridge is stacked on a PCIe-to-PCI bridge, we can have
PCIe endpoints masked by a conventional PCI bus.  This makes the extended
config space of the PCIe endpoint inaccessible.  The PCIe-to-PCI bridge is
supposed to handle any type 1 configuration transactions where the extended
config offset bits are non-zero as an Unsupported Request rather than
forward it to the secondary interface.  As noted here, there are a couple
known offenders to this rule.  These bridges drop the extended offset bits,
resulting in the conventional config space being aliased many times across
the extended config space.  For Intel NICs, this alias often seems to
expose a bogus SR-IOV cap.

Stacking bridges may seem like an uncommon scenario, but note that any
conventional PCI slot in a modern PC is already the secondary interface of
an onboard PCIe-to-PCI bridge.  The user need only add a PCI-to-PCIe
adapter and PCIe device to encounter this problem.

Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-27 15:07:41 -06:00
Yijing Wang
6788a51fe3 PCI: Use pci_is_bridge() to simplify code
Use pci_is_bridge() to simplify code.  No functional change.

Requires: 326c1cdae7 PCI: Rename pci_is_bridge() to pci_has_subordinate()
Requires: 1c86438c94 PCI: Add new pci_is_bridge() interface
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-27 14:53:41 -06:00
Bjorn Helgaas
e5558d1a51 Merge branches 'dma-api', 'pci/virtualization', 'pci/msi', 'pci/misc' and 'pci/resource' into next
* dma-api:
  iommu/exynos: Remove unnecessary "&" from function pointers
  DMA-API: Update dma_pool_create ()and dma_pool_alloc() descriptions
  DMA-API: Fix duplicated word in DMA-API-HOWTO.txt
  DMA-API: Capitalize "CPU" consistently
  sh/PCI: Pass GAPSPCI_DMA_BASE CPU & bus address to dma_declare_coherent_memory()
  DMA-API: Change dma_declare_coherent_memory() CPU address to phys_addr_t
  DMA-API: Clarify physical/bus address distinction

* pci/virtualization:
  PCI: Mark RTL8110SC INTx masking as broken

* pci/msi:
  PCI/MSI: Remove pci_enable_msi_block()

* pci/misc:
  PCI: Remove pcibios_add_platform_entries()
  s390/pci: use pdev->dev.groups for attribute creation
  PCI: Move Open Firmware devspec attribute to PCI common code

* pci/resource:
  PCI: Add resource allocation comments
  PCI: Simplify __pci_assign_resource() coding style
  PCI: Change pbus_size_mem() return values to be more conventional
  PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources
  PCI: Support BAR sizes up to 8GB
  resources: Clarify sanity check message
  PCI: Don't add disabled subtractive decode bus resources
  PCI: Don't print anything while decoding is disabled
  PCI: Don't set BAR to zero if dma_addr_t is too small
  PCI: Don't convert BAR address to resource if dma_addr_t is too small
  PCI: Reject BAR above 4GB if dma_addr_t is too small
  PCI: Fail safely if we can't handle BARs larger than 4GB
  x86/gart: Tidy messages and add bridge device info
  x86/gart: Replace printk() with pr_info()
  x86/PCI: Move pcibios_assign_resources() annotation to definition
  x86/PCI: Mark ATI SBx00 HPET BAR as IORESOURCE_PCI_FIXED
  x86/PCI: Don't try to move IORESOURCE_PCI_FIXED resources
  x86/PCI: Fix Broadcom CNB20LE unintended sign extension
2014-05-26 17:29:17 -06:00
Bjorn Helgaas
d739a099d0 PCI: Don't add disabled subtractive decode bus resources
For a subtractive decode bridge, we previously added and printed all
resources of the primary bus, even if they were not valid.  In the example
below, the bridge 00:1c.3 has no windows enabled, so there are no valid
resources on bus 02.  But since 02:00.0 is subtractive decode bridge, we
add and print all those invalid resources, which don't really make sense:

  pci 0000:00:1c.3: PCI bridge to [bus 02-03]
  pci 0000:02:00.0: PCI bridge to [bus 03] (subtractive decode)
  pci 0000:02:00.0:   bridge window [??? 0x00000000 flags 0x0] (subtractive decode)

Add and print the subtractively-decoded resources only if they are valid.

There's an example in the dmesg log attached to the bugzilla below (but
this patch doesn't fix the bug reported there).

Link: https://bugzilla.kernel.org/show_bug.cgi?id=73141
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-23 10:47:20 -06:00
Bjorn Helgaas
26370fc664 PCI: Don't print anything while decoding is disabled
If the console is a PCI device, and we try to print to it while its
decoding is disabled, the system will hang.  This particular printk hasn't
caused a problem yet, but it could, so this fixes it.

See also 0ff9514b57 ("PCI: Don't print anything while decoding is
disabled").

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-23 10:47:20 -06:00
Bjorn Helgaas
31e9dd2565 PCI: Don't set BAR to zero if dma_addr_t is too small
If a BAR is above 4GB and our dma_addr_t is too small, don't clear the BAR
to zero: that doesn't disable the BAR, and it makes it more likely that the
BAR will conflict with things if we turn on the memory enable bit (as we
will at "out:" if the device was already enabled at the handoff).

We should also print the BAR info and its original size so we can follow
the process when we try to assign space to it.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-23 10:47:20 -06:00
Bjorn Helgaas
72dc5601fe PCI: Don't convert BAR address to resource if dma_addr_t is too small
If dma_addr_t is too small to represent the BAR value,
pcibios_bus_to_resource() will fail, so just remember the BAR size directly
in the resource.  The resource is already marked UNSET, so we know the
address isn't valid anyway.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-23 10:47:20 -06:00
Bjorn Helgaas
d1a313e4b6 PCI: Reject BAR above 4GB if dma_addr_t is too small
We can only handle BARs above 4GB if dma_addr_t (not resource_size_t) is 64
bits wide.  If we have a 64-bit resource_size_t and a 32-bit dma_addr_t,
we can't deal with BARs above 4GB.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-23 10:47:19 -06:00
Bjorn Helgaas
23b13bc76f PCI: Fail safely if we can't handle BARs larger than 4GB
We can only handle BARs larger than 4GB if both dma_addr_t and
resource_size_t are 64 bits wide.  If dma_addr_t is 32 bits, we can't
represent all the bus addresses, and if resource_size_t is 32 bits, we
can't represent all the CPU addresses.

Previously we cleared res->flags (at "fail:") for resources that were too
large.  That means we think the BAR doesn't exist at all, which in turn
means that we could enable the device even though we can't keep track of
where the BAR is and we can't make sure it doesn't overlap something else.

This preserves the type flags (MEM/IO) so we can keep from enabling the
device.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-05-23 10:47:19 -06:00
Bjorn Helgaas
1e358f94c0 PCI: Fix use of uninitialized MPS value
If "pcie_bus_config == PCIE_BUS_PERFORMANCE", we don't initialize "smpss",
so we pass a pointer to garbage into pcie_bus_configure_set(), where we
compute "mps" based on the garbage.  We then pass the garbage "mps" to
pcie_write_mps(), which ignores it in the PCIE_BUS_PERFORMANCE case.

Coverity isn't smart enough to deduce that we ignore the garbage (it's a
lot to expect from a human, too), so initialize "smpss" to a safe value in
all cases.

Found by Coverity (CID 146454).

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-04-29 17:36:44 -06:00
Bjorn Helgaas
10874f5a00 PCI: Remove unnecessary __ref annotations
Some PCI functions used to be marked __devinit.  When CONFIG_HOTPLUG was
not set, these functions were discarded after boot.  A few callers of these
__devinit functions were marked __ref to indicate that they could safely
call the __devinit functions even though the callers were not __devinit.

But CONFIG_HOTPLUG and __devinit are now gone, and the need for the __ref
annotations is also gone, so remove them.  Relevant historical commits:

  54b956b903 Remove __dev* markings from init.h
  a8e4b9c101 PCI: add generic pci_hp_add_bridge()
  0ab2b57f8d PCI: fix section mismatch warning in pci_scan_child_bus
  451124a7cc PCI: fix 4x section mismatch warnings

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-04-29 17:36:44 -06:00
Bjorn Helgaas
30723cbf6f Merge branch 'pci/resource' into next
* pci/resource: (26 commits)
  Revert "[PATCH] Insert GART region into resource map"
  PCI: Log IDE resource quirk in dmesg
  PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
  PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
  resources: Set type in __request_region()
  PCI: Don't check resource_size() in pci_bus_alloc_resource()
  s390/PCI: Use generic pci_enable_resources()
  tile PCI RC: Use default pcibios_enable_device()
  sparc/PCI: Use default pcibios_enable_device() (Leon only)
  sh/PCI: Use default pcibios_enable_device()
  microblaze/PCI: Use default pcibios_enable_device()
  alpha/PCI: Use default pcibios_enable_device()
  PCI: Add "weak" generic pcibios_enable_device() implementation
  PCI: Don't enable decoding if BAR hasn't been assigned an address
  PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
  PCI: Don't try to claim IORESOURCE_UNSET resources
  PCI: Check IORESOURCE_UNSET before updating BAR
  PCI: Don't clear IORESOURCE_UNSET when updating BAR
  PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
  PCI: Remove pci_find_parent_resource() use for allocation
  ...
2014-03-19 15:11:19 -06:00
Bjorn Helgaas
075eb9e355 PCI: Log IDE resource quirk in dmesg
Make a note in dmesg when we overwrite legacy IDE BAR info.  We previously
logged something like this:

  pci 0000:00:1f.1: reg 0x10: [io  0x0000-0x0007]

and then silently overwrote the resource.  There's an example in the
bugzilla below.  This doesn't fix the bugzilla; it just makes what's going
on more obvious.

No functional change; merely adds some dev_info() calls.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=48451
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-03-19 15:00:17 -06:00
Bjorn Helgaas
c83bd900aa PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
If we don't support 64-bit addresses, i.e., CONFIG_PHYS_ADDR_T_64BIT is not
set, we can't deal with BARs above 4GB.  In this case we already pretend
the BAR contained zero; this patch also sets IORESOURCE_UNSET so we can try
to reallocate it later.

I don't think this is exactly correct: what we care about here are *bus*
addresses, not CPU addresses, so the tests of sizeof(resource_size_t)
probably should be on sizeof(dma_addr_t) instead.  But this is what's been
in -next, so we'll fix that later.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-27 10:43:33 -07:00
Andreas Noever
fc1b253141 PCI: Don't scan random busses in pci_scan_bridge()
When assigning a new bus number in pci_scan_bridge we check whether
max+1 is free by calling pci_find_bus. If it does already exist then we
assume that we are rescanning and that this is the right bus to scan.

This is fragile. If max+1 lies outside of bus->busn_res.end then we will
rescan some random bus from somewhere else in the hierachy. This patch
checks for this case and prints a warning.

[bhelgaas: add parent/child bus number info to dev_warn()]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-11 15:21:08 -07:00
Andreas Noever
c95b0bd6ca PCI: Check for child busses which use more bus numbers than allocated
pci_scan_child_bus can (potentially) return a bus number higher than the
subordinate value of the child bus. Possible reasons are that bus numbers
are reserved for SR-IOV or for CardBus (SR-IOV is done without checks and
the CardBus checks are sketchy at best).

We clamp the returned value to the actual subordinate value and print a
warning if too many bus numbers are reserved.

[bhelgaas: whitespace]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-11 15:16:09 -07:00
Andreas Noever
f5fb40700f PCI: Remove pci_fixup_parent_subordinate_busnr()
The function has no effect.

If pcibios_assign_all_busses() is not set then the function does nothing.

If it is set then in pci_scan_bridge we are always in the branch where
we assign the bus numbers ourselves and the subordinate values of all
parent busses will be set to 0xff since that is what they inherited from
their parent bus and ultimately from the root bus.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-11 15:16:09 -07:00
Andreas Noever
1820ffdccb PCI: Make sure bus number resources stay within their parents bounds
Right now we use 0xff for busn_res.end when probing and later reduce it to
the value that is actually used. This does not work if a parent bridge has
already a lower subordinate value. For example during hotplug of a new
bridge below an already-configured bridge the following message is printed
from pci_bus_insert_busn_res():

  pci_bus 0000:06: busn_res: can not insert [bus 06-ff] under [bus 05-9b] (conflicts with (null) [bus 05-9b])

This patch clamps the bus range to that of the parent and also ensures that
we do not exceed the parents range when assigning the final subordinate
value.

We also check that busses configured by the firmware fit into their parents
bounds.

[bhelgaas: reword dev_warn() and fix printk format warning]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-10 17:12:45 -07:00
Andreas Noever
ced04d1551 PCI: Use request_resource_conflict() instead of insert_ for bus numbers
If a conflict happens during insert_resource_conflict() and all conflicts
fit within the newly inserted resource then they will become children of
the new resource. This is almost certainly not what we want for bus
numbers.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-10 17:12:23 -07:00
Andreas Noever
619c8c310f PCI: Assign CardBus bus number only during the second pass
Right now the CardBus code in pci_scan_bridge() is executed during both
passes. Since we always allocate the bus number ourselves it makes sense
to put it into the second pass.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-10 17:12:06 -07:00
Andreas Noever
2ed8582341 PCI: Clarify the "scan anyway" comment in pci_scan_bridge()
Initially when we encountered a bus that was already present we skipped
it. Since 74710ded8e 'PCI: always scan child buses' we continue
scanning in order to allow user triggered rescans of already existing
busses.

The old comment suggested that the reason for continuing the scan is a
bug in the i450NX chipset. This is not the case.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-10 17:11:15 -07:00
Andreas Noever
9a4d7d8719 PCI: Increment max correctly in pci_scan_bridge()
This patch fixes two small issues:
 - If pci_add_new_bus() fails, max must not be incremented. Otherwise
   an incorrect value is returned from pci_scan_bridge().
 - If the bus is already present, max must be incremented. I think
   that this case should only be hit if we trigger a manual rescan of a
   CardBus bridge.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-02-10 16:50:49 -07:00
Rafael J. Wysocki
04480094de Revert "PCI: Remove from bus_list and release resources in pci_release_dev()"
Revert commit ef83b0781a "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible.  For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).

Moreover, the problem that commit ef83b0781a attempted to address
cannot happen any more after commit 8a4c5c329d "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.

Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit ef83b0781a from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.

Fixes: ef83b0781a (PCI: Remove from bus_list and release resources in pci_release_dev())
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-02-01 10:24:31 -08:00
Rafael J. Wysocki
9d16947b75 PCI: Add global pci_lock_rescan_remove()
There are multiple PCI device addition and removal code paths that may be
run concurrently with the generic PCI bus rescan and device removal that
can be triggered via sysfs.  If that happens, it may lead to multiple
different, potentially dangerous race conditions.

The most straightforward way to address those problems is to run
the code in question under the same lock that is used by the
generic rescan/remove code in pci-sysfs.c.  To prepare for those
changes, move the definition of the global PCI remove/rescan lock
to probe.c and provide global wrappers, pci_lock_rescan_remove()
and pci_unlock_rescan_remove(), allowing drivers to manipulate
that lock.  Also provide pci_stop_and_remove_bus_device_locked()
for the callers of pci_stop_and_remove_bus_device() who only need
to hold the rescan/remove lock around it.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-01-13 17:49:49 -07:00
Bjorn Helgaas
597db6f38c Merge branch 'pci/dead-code' into next
* pci/dead-code:
  PCI: Make local functions static
  PCI: Remove unused alloc_pci_dev()
  PCI: Remove unused pci_renumber_slot()
  PCI: Remove unused pcie_aspm_enabled()
  PCI: Remove unused pci_vpd_truncate()
  PCI: Remove unused ID-Based Ordering support
  PCI: Remove unused Optimized Buffer Flush/Fill support
  PCI: Remove unused Latency Tolerance Reporting support
  PCI: Removed unused parts of Page Request Interface support

Conflicts:
	drivers/pci/pci.c
	include/linux/pci.h
2014-01-13 16:47:08 -07:00
Stephen Hemminger
0b950f0f3c PCI: Make local functions static
Using 'make namespacecheck' identify code which should be declared static.
Checked for users in other driver/archs as well.  Compile tested only.

This stops exporting the following interfaces to modules:

    pci_target_state()
    pci_load_saved_state()

[bhelgaas: retained pci_find_next_ext_capability() and pci_cfg_space_size()]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-01-13 11:57:29 -07:00
Stephen Hemminger
e2760c54a4 PCI: Remove unused alloc_pci_dev()
My philosophy is unused code is dead code.  And dead code is subject to bit
rot and is a likely source of bugs.  Use it or lose it.

This removes this unused and deprecated interface:

    alloc_pci_dev()

[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-01-13 11:57:29 -07:00
Bjorn Helgaas
96702be560 Merge branch 'pci/resource' into next
* pci/resource:
  PCI: Allocate 64-bit BARs above 4G when possible
  PCI: Enforce bus address limits in resource allocation
  PCI: Split out bridge window override of minimum allocation address
  agp/ati: Use PCI_COMMAND instead of hard-coded 4
  agp/intel: Use CPU physical address, not bus address, for ioremap()
  agp/intel: Use pci_bus_address() to get GTTADR bus address
  agp/intel: Use pci_bus_address() to get MMADR bus address
  agp/intel: Support 64-bit GMADR
  agp/intel: Rename gtt_bus_addr to gtt_phys_addr
  drm/i915: Rename gtt_bus_addr to gtt_phys_addr
  agp: Use pci_resource_start() to get CPU physical address for BAR
  agp: Support 64-bit APBASE
  PCI: Add pci_bus_address() to get bus address of a BAR
  PCI: Convert pcibios_resource_to_bus() to take a pci_bus, not a pci_dev
  PCI: Change pci_bus_region addresses to dma_addr_t
2014-01-10 14:23:15 -07:00
Yinghai Lu
fc2798502f PCI: Convert pcibios_resource_to_bus() to take a pci_bus, not a pci_dev
These interfaces:

  pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
  pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)

took a pci_dev, but they really depend only on the pci_bus.  And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:

  pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
  pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)

In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-12-21 10:06:10 -07:00
Yinghai Lu
ef83b0781a PCI: Remove from bus_list and release resources in pci_release_dev()
Previously we removed the pci_dev from the bus_list and released its
resources in pci_destroy_dev().  But that's too early: it's possible to
call pci_destroy_dev() twice for the same device (e.g., via sysfs), and
that will cause an oops when we try to remove it from bus_list the second
time.

We should remove it from the bus_list only when the last reference to the
pci_dev has been released, i.e., in pci_release_dev().

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-12-18 13:53:40 -07:00
Yinghai Lu
ef37702eb3 PCI: Move pci_proc_attach_device() to pci_bus_add_device()
4f535093cf ("PCI: Put pci_dev in device tree as early as possible")
moved pci_proc_attach_device() from pci_bus_add_device() to
pci_device_add().

This moves it back to pci_bus_add_device(), essentially reverting that
part of 4f535093cf.  This makes it symmetric with pci_stop_dev(),
where we call pci_proc_detach_device() and pci_remove_sysfs_dev_files()
and set dev->is_added = 0.

[bhelgaas: changelog, create sysfs then attach proc for symmetry]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-12-18 13:53:38 -07:00
Bjorn Helgaas
f7625980f5 PCI: Fix whitespace, capitalization, and spelling errors
Fix whitespace, capitalization, and spelling errors.  No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.

Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-11-14 11:28:18 -07:00
Bjorn Helgaas
605d240052 Merge branch 'pci/misc' into next
* pci/misc:
  PCI: Remove unused PCI_MSIX_FLAGS_BIRMASK definition
  PCI: acpiphp_ibm: Convert to dynamic debug
  PCI: acpiphp: Convert to dynamic debug
  PCI: Remove Intel Haswell D3 delays
  PCI: Pass type, width, and prefetchability for window alignment
  PCI: Document reason for using pci_is_root_bus()
  PCI: Use pci_is_root_bus() to check for root bus
  PCI: Remove unused "is_pcie" from pci_dev structure
  PCI: Update pci_find_slot() description in pci.txt
  [SCSI] qla2xxx: Use standard PCIe Capability Link register field names
  PCI: Fix comment typo, remove unnecessary !! in pci_is_pcie()
  PCI: Drop "setting latency timer" messages
2013-09-27 16:35:43 -06:00
Yijing Wang
115e3bc5e2 PCI: Remove unused "is_pcie" from pci_dev structure
No one uses "is_pcie" now; remove this obsolete member.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-09-25 15:43:44 -06:00
Yijing Wang
fdfe151127 PCI: Use pci_is_pcie() to simplify code
Use pci_is_pcie() instead of pci_find_capability() to simplify code.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-09-23 17:30:03 -06:00
Linus Torvalds
b4b50fd78b ARM: SoC platform changes for 3.12
This branch contains mostly additions and changes to platform enablement
 and SoC-level drivers. Since there's sometimes a dependency on device-tree
 changes, there's also a fair amount of those in this branch.
 
 Pieces worth mentioning are:
 
 - Mbus driver for Marvell platforms, allowing kernel configuration
   and resource allocation of on-chip peripherals.
 - Enablement of the mbus infrastructure from Marvell PCI-e drivers.
 - Preparation of MSI support for Marvell platforms.
 - Addition of new PCI-e host controller driver for Tegra platforms
 - Some churn caused by sharing of macro names between i.MX 6Q and 6DL
   platforms in the device tree sources and header files.
 - Various suspend/PM updates for Tegra, including LP1 support.
 - Versatile Express support for MCPM, part of big little support.
 - Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
 - OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
 
 The code that touches other architectures are patches moving
 MSI arch-specific functions over to weak symbols and removal of
 ARCH_SUPPORTS_MSI, acked by PCI maintainers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJSKhYmAAoJEIwa5zzehBx322AP/1ONYs8o8f7/Gzq6lZvTN6T3
 0pBTApg6Jfioi3lwKvUAEIcsW82YKQ+UZkbW66GQH6+Ri4aZJKZHuz0+JPU67OJ4
 LtSLuzVWrymy2VOOUvAnS/SXkOZw/pHhU4cLNHn1dMndhUL1Uqp9/XwuiHEQyFsP
 uOkpcBtIu0EWElov0PKKZ5SWBg8JJs2vy5ydiViGelWHCrZvDDZkWzIsDcBQxJLQ
 juzT4+JE+KOu7vKmfw78o6iHoCS2TBRAN9YUCajRb8Wl+out1hrTahHnDWaZ5Mce
 EskcQNkJROqFbjD4k3ABN4XGTv2VDmrztIwFe0SEQ7Dz/9ypCrBGT69uI9xIqTXr
 GwVRIwAUFTpMupK0gy93z1ajV3N0CXV79out9+jQNUQybYE+czp8QOyhmuc1tZx0
 8fn9jlBQe9Vy6yrs39gEcE7nUwrayeyQ+6UvqqwsE2pWZabNAnCMSPX5+QIu+T/3
 tQ7+jYmfFeserp1sIDOHOnxfhtW9EI6U9d1h/DUCwrsuFdkL9ha4M/vh9Pwgye98
 tBdz0T4yE39AJQwwFWRkv1jcQKcGu6WqJanmvS4KRBksGwuLWxy+ewOnkz2ifS25
 ZYSyxAryZRBvQRqlOK11rXPfRcbGcY0MG9lkKX96rGcyWEizgE1DdjxXD8HoIleN
 R8heV6GX5OzlFLGX2tKK
 =fJ5x
 -----END PGP SIGNATURE-----

Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform changes from Olof Johansson:
 "This branch contains mostly additions and changes to platform
  enablement and SoC-level drivers.  Since there's sometimes a
  dependency on device-tree changes, there's also a fair amount of
  those in this branch.

  Pieces worth mentioning are:

   - Mbus driver for Marvell platforms, allowing kernel configuration
     and resource allocation of on-chip peripherals.
   - Enablement of the mbus infrastructure from Marvell PCI-e drivers.
   - Preparation of MSI support for Marvell platforms.
   - Addition of new PCI-e host controller driver for Tegra platforms
   - Some churn caused by sharing of macro names between i.MX 6Q and 6DL
     platforms in the device tree sources and header files.
   - Various suspend/PM updates for Tegra, including LP1 support.
   - Versatile Express support for MCPM, part of big little support.
   - Allwinner platform support for A20 and A31 SoCs (dual and quad
     Cortex-A7)
   - OMAP2+ support for DRA7, a new Cortex-A15-based SoC.

  The code that touches other architectures are patches moving MSI
  arch-specific functions over to weak symbols and removal of
  ARCH_SUPPORTS_MSI, acked by PCI maintainers"

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
  tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
  PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
  ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
  ARM: dts: vf610-twr: enable i2c0 device
  ARM: dts: i.MX51: Add one more I2C2 pinmux entry
  ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
  ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
  ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
  ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
  ARM: dts: i.MX27: Disable AUDMUX in the template
  ARM: dts: wandboard: Add support for SDIO bcm4329
  ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
  ARM: dts: imx53-qsb: Make USBH1 functional
  ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
  ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
  ARM: dts: imx6qdl-sabresd: Add touchscreen support
  ARM: imx: add ocram clock for imx53
  ARM: dts: imx: ocram size is different between imx6q and imx6dl
  ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
  ARM: dts: i.MX27: Remove clock name from CPU node
  ...
2013-09-06 13:30:06 -07:00
Linus Torvalds
cc998ff881 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking changes from David Miller:
 "Noteworthy changes this time around:

   1) Multicast rejoin support for team driver, from Jiri Pirko.

   2) Centralize and simplify TCP RTT measurement handling in order to
      reduce the impact of bad RTO seeding from SYN/ACKs.  Also, when
      both timestamps and local RTT measurements are available prefer
      the later because there are broken middleware devices which
      scramble the timestamp.

      From Yuchung Cheng.

   3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
      memory consumed to queue up unsend user data.  From Eric Dumazet.

   4) Add a "physical port ID" abstraction for network devices, from
      Jiri Pirko.

   5) Add a "suppress" operation to influence fib_rules lookups, from
      Stefan Tomanek.

   6) Add a networking development FAQ, from Paul Gortmaker.

   7) Extend the information provided by tcp_probe and add ipv6 support,
      from Daniel Borkmann.

   8) Use RCU locking more extensively in openvswitch data paths, from
      Pravin B Shelar.

   9) Add SCTP support to openvswitch, from Joe Stringer.

  10) Add EF10 chip support to SFC driver, from Ben Hutchings.

  11) Add new SYNPROXY netfilter target, from Patrick McHardy.

  12) Compute a rate approximation for sending in TCP sockets, and use
      this to more intelligently coalesce TSO frames.  Furthermore, add
      a new packet scheduler which takes advantage of this estimate when
      available.  From Eric Dumazet.

  13) Allow AF_PACKET fanouts with random selection, from Daniel
      Borkmann.

  14) Add ipv6 support to vxlan driver, from Cong Wang"

Resolved conflicts as per discussion.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
  openvswitch: Fix alignment of struct sw_flow_key.
  netfilter: Fix build errors with xt_socket.c
  tcp: Add missing braces to do_tcp_setsockopt
  caif: Add missing braces to multiline if in cfctrl_linkup_request
  bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
  vxlan: Fix kernel panic on device delete.
  net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
  net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
  icplus: Use netif_running to determine device state
  ethernet/arc/arc_emac: Fix huge delays in large file copies
  tuntap: orphan frags before trying to set tx timestamp
  tuntap: purge socket error queue on detach
  qlcnic: use standard NAPI weights
  ipv6:introduce function to find route for redirect
  bnx2x: VF RSS support - VF side
  bnx2x: VF RSS support - PF side
  vxlan: Notify drivers for listening UDP port changes
  net: usbnet: update addr_assign_type if appropriate
  driver/net: enic: update enic maintainers and driver
  driver/net: enic: Exposing symbols for Cisco's low latency driver
  ...
2013-09-05 14:54:29 -07:00
Bjorn Helgaas
2e8b5f621d Merge branch 'pci/misc' into next
* pci/misc:
  PCI: Remove pcie_cap_has_devctl()
  PCI: Support PCIe Capability Slot registers only for ports with slots
  PCI: Remove PCIe Capability version checks
  PCI: Allow PCIe Capability link-related register access for switches
  PCI: Add offsets of PCIe capability registers
  PCI: Tidy bitmasks and spacing of PCIe capability definitions
  PCI: Remove obsolete comment reference to pci_pcie_cap2()
  PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
  PCI: Rename PCIe capability definitions to follow convention
  PCI: Disable decoding for BAR sizing only when it was actually enabled
  PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
  PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
2013-08-28 20:55:41 -06:00
Bjorn Helgaas
07f2daad09 Merge branch 'pci/yijing-mps-v8' into next
* pci/yijing-mps-v8:
  PCI: Warn if unsafe MPS settings detected
  PCI: Fix MPS peer-to-peer DMA comment syntax
  PCI: Don't restrict MPS for slots below Root Ports
  PCI: Simplify MPS test for Downstream Port
  PCI: Remove unnecessary check for pcie_get_mps() failure
  PCI: Simplify pcie_bus_configure_settings() interface
  PCI: Drop "PCI-E" prefix from Max Payload Size message
2013-08-26 15:40:34 -06:00
Bjorn Helgaas
1193725f54 Merge branch 'pci/yinghai-assign-unassigned-v6' into next
* pci/yinghai-assign-unassigned-v6:
  PCI: Assign resources for hot-added host bridge more aggressively
  PCI: Move resource reallocation code to non-__init
  PCI: Delay enabling bridges until they're needed
  PCI: Assign resources on a per-bus basis
  PCI: Enable unassigned resource reallocation on per-bus basis
  PCI: Turn on reallocation for unassigned resources with host bridge offset
  PCI: Look for unassigned resources on per-bus basis
  PCI: Drop temporary variable in pci_assign_unassigned_resources()
2013-08-26 15:40:03 -06:00
Yijing Wang
5895af7915 PCI: Warn if unsafe MPS settings detected
If a BIOS configures MPS incorrectly, devices may not work normally.
For example, if a bridge has MPS set larger than an endpoint below it,
the endpoint may discard packets.

To help diagnose this issue, print a warning if we find an endpoint
MPS setting different than that of the upstream bridge.

[bhelgaas: changelog, "bridge" temporary, warning text]
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=60799
Reported-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jon Mason <jdmason@kudzu.us>
2013-08-26 14:49:28 -06:00
Jon Mason
3315472c47 PCI: Fix MPS peer-to-peer DMA comment syntax
Correct minor wording issue in MPS peer-to-peer comment.  Noticed by Don
Dutile.

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-08-26 11:21:44 -06:00
Zoltan Kiss
808e34e2cd PCI: Disable decoding for BAR sizing only when it was actually enabled
We disable BARs while sizing them so we don't cause conflicts with other
devices (see 253d2e5498 and bbffe43524).  But if device decoding is already
disabled before we size the BAR, we don't need to disable it again.

[bhelgaas: changelog, add PCI_COMMAND_DECODING_ENABLE for readability]
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-08-23 09:21:19 -06:00
Yijing Wang
d4aa68f614 PCI: Don't restrict MPS for slots below Root Ports
When booting with "pci=pcie_bus_safe", we previously limited the
fabric MPS to 128 when we found:

  (1) A hotplug-capable Downstream Port ("dev->is_hotplug_bridge &&
      pci_pcie_type(dev) != PCI_EXP_TYPE_ROOT_PORT"), or

  (2) A hotplug-capable Root Port with a slot that was either empty or
      contained a multi-function device ("dev->is_hotplug_bridge &&
      !list_is_singular(&dev->bus->devices)")

Part (1) is valid, but part (2) is not.

After a hot-add in the slot below a Root Port, we can reconfigure all
MPS values in the fabric below the Root Port because the new device is
the only thing below the Root Port and there are no active drivers.
Therefore, there's no reason to limit the MPS for Root Ports, no
matter what's in the slot.

Test info:

    -+-[0000:40]-+-07.0-[0000:46]--+-00.0  Intel 82576 NIC
                                   \-00.1  Intel 82576 NIC

    0000:40:07.0 Root Port bridge to [bus 46] (MPS supported=256)
    0000:46:00.0 Endpoint                     (MPS supported=512)
    0000:46:00.1 Endpoint                     (MPS supported=512)

    # echo 0 > /sys/bus/pci/slots/7/power
    # echo 1 > /sys/bus/pci/slots/7/power
    pcieport 0000:40:07.0: PCI-E Max Payload Size set to 256/ 256 (was 256)
    pci 0000:46:00.0:      PCI-E Max Payload Size set to 256/ 512 (was 128)
    pci 0000:46:00.1:      PCI-E Max Payload Size set to 256/ 512 (was 128)

Before this change, we set MPS to 128 for the Root Port and both NICs
because the slot contained a multi-function device and

    dev->is_hotplug_bridge && !list_is_singular(&dev->bus->devices)

was true.  After this change, we set it to 256.

[bhelgaas: changelog, comments, split out upstream bridge check]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jon Mason <jdmason@kudzu.us>
2013-08-22 10:47:04 -06:00
Bjorn Helgaas
c2996948ac PCI: Simplify MPS test for Downstream Port
PCIe hotplug bridges are always either Root Ports or Downstream Ports.  No
other device type can have a PCIe link leading downstream to a slot.

Root Ports don't have an upstream bridge, so "dev->is_hotplug_bridge &&
dev->bus->self" is true if and only if "dev" is a Downstream Port.  That
means we can simplify this by looking at the type of "dev" itself, without
looking upstream at all.

No functional change.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-08-22 10:47:04 -06:00
Bjorn Helgaas
a58674ff83 PCI: Simplify pcie_bus_configure_settings() interface
Based on a patch by Jon Mason (see URL below).

All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss".  The "mpss" argument is redundant since we
can easily look it up internally.  In addition, all callers check
"bus->self" for NULL, which we can also do internally.

This patch simplifies the interface and the callers.  No functional change.

Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-08-22 10:47:02 -06:00
Bjorn Helgaas
2c25e34c75 PCI: Drop "PCI-E" prefix from Max Payload Size message
The conventional spelling is "PCIe", but I think even that is superfluous,
so remove the whole thing.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-08-22 10:47:01 -06:00
Thierry Reding
0cbdcfcf42 PCI: Introduce new MSI chip infrastructure
The new struct msi_chip is used to associated an MSI controller with a
PCI bus. It is automatically handed down from the root to its children
during bus enumeration.

This patch provides default (weak) implementations for the architecture-
specific MSI functions (arch_setup_msi_irq(), arch_teardown_msi_irq()
and arch_msi_check_device()) which check if a PCI device's bus has an
attached MSI chip and forward the call appropriately.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-08-12 15:26:58 +00:00
Jacob Keller
343e51ae6e PCI: expose pcie_link_speed and pcix_bus_speed arrays
pcie_link_speed and pcix_bus_speed are arrays used by probe.c to correctly
convert lnksta register values into the pci_bus_speed enum. These static arrays
are useful outside probe for this purpose. This patch makes these defines into
conist arrays and exposes them with an extern header in drivers/pci/pci.h

-v2-
* move extern declarations to drivers/pci/pci.h

CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-07-30 18:16:36 -07:00
Yinghai Lu
928bea9648 PCI: Delay enabling bridges until they're needed
We currently enable PCI bridges after scanning a bus and assigning
resources.  This is often done in arch code.

This patch changes this so we don't enable a bridge until necessary, i.e.,
until we enable a PCI device behind the bridge.  We do this in the generic
pci_enable_device() path, so this also removes the arch-specific code to
enable bridges.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-07-25 12:35:03 -06:00
Greg Kroah-Hartman
56039e658c PCI: Convert class code to use dev_groups
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead.  This converts the PCI class code to use the
correct field.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-07-25 12:18:42 -06:00
Bjorn Helgaas
df58f46c0f Merge branch 'pci/jiang-bus-lock-v3' into next
* pci/jiang-bus-lock-v3:
  PCI: Return early on allocation failures to unindent mainline code
  PCI: Simplify IOV implementation and fix reference count races
  PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
  unicore32/PCI: Remove redundant call of pci_bus_add_devices()
  m68k/PCI: Remove redundant call of pci_bus_add_devices()
  PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
  PCI: Fix refcount issue in pci_create_root_bus() error recovery path
  ia64/PCI: Clean up pci_scan_root_bus() usage
  PCI: Convert alloc_pci_dev(void) to pci_alloc_dev(bus)
  PCI: Introduce pci_alloc_dev(struct pci_bus*) to replace alloc_pci_dev()
  PCI: Introduce pci_bus_{get|put}() to manage PCI bus reference count

Conflicts:
	drivers/pci/probe.c
2013-06-14 17:47:46 -06:00
Bjorn Helgaas
050134864c PCI: Return early on allocation failures to unindent mainline code
On allocation failure, return early so the main body of the function
doesn't have to be indented as the body of an "if" statement.  No
functional change.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-06-14 17:39:45 -06:00
Bjorn Helgaas
726246d2e6 Merge branch 'pci/misc' into next
* pci/misc:
  PCI / ACPI / PM: Use correct power state strings in messages
  PCI: Fix comment typo for pcie_pme_remove()
  PCI: Add pcibios_release_device()
2013-06-14 17:08:48 -06:00
Jiang Liu
70efde2a29 PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
This renames pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
and moves it next to pci_alloc_host_bridge().  No functional change.

[bhelgaas: split rename & move out of create/destroy symmetry patch]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-06-07 16:16:51 -06:00
Jiang Liu
343df771e6 PCI: Fix refcount issue in pci_create_root_bus() error recovery path
After calling device_register(&bridge->dev), the bridge is reference-
counted, and it is illegal to call kfree() on it except in the release
function.

[bhelgaas: changelog, use put_device() after device_register() failure]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
2013-06-07 14:42:03 -06:00
Gu Zheng
8b1fce04dc PCI: Convert alloc_pci_dev(void) to pci_alloc_dev(bus)
Use the new pci_alloc_dev(bus) to replace the existing using of
alloc_pci_dev(void).

[bhelgaas: drop pci_bus ref later in pci_release_dev()]
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
2013-06-05 13:49:36 -06:00
Sebastian Ott
6ae32c539c PCI: Add pcibios_release_device()
Platforms may want to provide architecture-specific functionality when
a PCI device is released.  Add a pcibios_release_device() call that
architectures can override to do so.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-06-04 17:24:31 -06:00
Gu Zheng
3c6e6ae770 PCI: Introduce pci_alloc_dev(struct pci_bus*) to replace alloc_pci_dev()
Here we introduce a new interface to replace alloc_pci_dev():

    struct pci_dev *pci_alloc_dev(struct pci_bus *bus)

It takes a "struct pci_bus *" argument, so we can alloc a PCI device
on a target PCI bus, and it acquires a reference on the pci_bus.
We use pci_alloc_dev(NULL) to simplify the old alloc_pci_dev(),
and keep it for a while but mark it as __deprecated.

Holding a reference to the pci_bus ensures that referencing
pci_dev->bus is valid as long as the pci_dev is valid.

[bhelgaas: keep existing "return error early" structure in pci_alloc_dev()]
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-05-27 16:23:28 -06:00
Kevin Hao
cf4d1cf5ac PCI: Unset resource if initial BAR value is invalid
The initial BAR value in the following example is invalid:

  pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff] (bus address [0xe0000000-0xffffffff])
  pci 0000:01:00.0: reg 10: initial BAR value: 0xa0000000
  pci 0000:01:00.0: reg 10: [mem 0xa0000000-0xa000007f 64bit]

bus_to_resource(0xa0000000) yields 0xa0000000 because there's no host
bridge window whose bus address range contains 0xa0000000.  But CPU
accesses to 0xa0000000 appear on the bus at 0xe0000000, so they will
not be claimed if the BAR contains 0xa0000000.

If we find a BAR where resource_to_bus(bus_to_resource(A)) != A, we can
work around this problem by reassigning the BAR.

[bhelgaas: changelog, comment]
Reference: https://lkml.kernel.org/r/1368536876-27307-3-git-send-email-haokexin@gmail.com
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-05-25 12:02:56 -06:00
Kevin Hao
96ddef25b2 PCI: Consolidate calls to pcibios_bus_to_resource() in __pci_read_base()
Since we will invoke pcibios_bus_to_resource() unconditionally if we
don't goto fail, move it out of if/else wrap.  No function change.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-05-25 12:01:24 -06:00
Kevin Hao
33963e308e PCI: Add 0x prefix to BAR register position in __pci_read_base()
We print the BAR register's position in hexadecimal format, so it
is more readable if 0x prefix is added.

[bhelgaas: keep dev_printk(), not dev_dbg(), so this is always in dmesg]
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-05-25 11:58:01 -06:00
Linus Torvalds
e15e611906 PCI updates for v3.10:
MSI
       PCI: Set ->mask_pos correctly
   Hotplug
       PCI: Delay final fixups until resources are assigned
   Moorestown
       x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJRi9CqAAoJEFmIoMA60/r82WIQAMJE7kwl88TpIw4QdTum4a+z
 E+eBMnGFSw/y7JNP81rOuLG8xZiZNQxGUvTEVV+WY6n7xhRSwcNZIiVqZ1xSBSjM
 PpmLOLrXI6I9JIouBLKIRiPOzbC7iB6O7RhKZCO68guQ8Y7epYoJjORaKELGZmN+
 09fVapvHHhcOcYYYAiUWvobjk6vCx4+6dSj6tRldI8JNl+WQtqMaK2P3QjsncZek
 20OXcrfv4X3ApoSwXcn1NUUDSlrAgM+VcwL6RJK9boURDnPOU8IzaD78DQVOUCNx
 BfLULFYkBq62ExCpTkg4Xo8aRowLAEcThZ3Z8/XtMmFlWDSdNm5BaTkYnPCf7nGW
 +8Oaxjm0pNVa5QnQqoK1HWpWtU1JTA0hO1tmJ9WyU+84GPuqTN3qiJTigfC9NHOi
 mj8O98sgbzIENKszBRpaNctjKVxKNFrBzQ3kOdFGB7NBVXN0pC2jnGBoxuxUrU3B
 h/yMB0Ku/GvnHRSngEhDzlkeuQpWTxvlhdjvlL63F0gEDQO0k3UPaiqD4zMpruga
 bHZ10v73Kdqp0FVatijmHztXO/yYB3m7tH3ZUDD3yfhKdaeOuTceDgbyo/ZwP2Wq
 gzOwuOVYLuJK68Qj4vkHJIKy86jHfNP4HGawhh8dECZDmsciarymQ+vAzobalYIu
 GSurydL4zqJJ+MIH84dW
 =B2U8
 -----END PGP SIGNATURE-----

Merge tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:
 "MSI:
      PCI: Set ->mask_pos correctly
  Hotplug:
      PCI: Delay final fixups until resources are assigned
  Moorestown:
      x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"

* tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Delay final fixups until resources are assigned
  x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0
  PCI: Set ->mask_pos correctly
2013-05-09 10:21:44 -07:00
Yinghai Lu
e253aaf0af PCI: Delay final fixups until resources are assigned
Commit 4f535093cf "PCI: Put pci_dev in device tree as early as possible"
moved final fixups from pci_bus_add_device() to pci_device_add().  But
pci_device_add() happens before resource assignment, so BARs may not be
valid yet.

Typical flow for hot-add:

    pciehp_configure_device
      pci_scan_slot
        pci_scan_single_device
          pci_device_add
            pci_fixup_device(pci_fixup_final, dev)  # previous location
      # resource assignment happens here
      pci_bus_add_devices
        pci_bus_add_device
          pci_fixup_device(pci_fixup_final, dev)    # new location

[bhelgaas: changelog, move fixups to pci_bus_add_device()]
Reference: https://lkml.kernel.org/r/20130415182614.GB9224@xanatos
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Tested-by: David Bulkow <David.Bulkow@stratus.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org	# v3.9+
2013-05-07 14:35:44 -06:00
Linus Torvalds
5a148af669 Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc update from Benjamin Herrenschmidt:
 "The main highlights this time around are:

   - A pile of addition POWER8 bits and nits, such as updated
     performance counter support (Michael Ellerman), new branch history
     buffer support (Anshuman Khandual), base support for the new PCI
     host bridge when not using the hypervisor (Gavin Shan) and other
     random related bits and fixes from various contributors.

   - Some rework of our page table format by Aneesh Kumar which fixes a
     thing or two and paves the way for THP support.  THP itself will
     not make it this time around however.

   - More Freescale updates, including Altivec support on the new e6500
     cores, new PCI controller support, and a pile of new boards support
     and updates.

   - The usual batch of trivial cleanups & fixes"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
  powerpc: Fix build error for book3e
  powerpc: Context switch the new EBB SPRs
  powerpc: Turn on the EBB H/FSCR bits
  powerpc: Replace CPU_FTR_BCTAR with CPU_FTR_ARCH_207S
  powerpc: Setup BHRB instructions facility in HFSCR for POWER8
  powerpc: Fix interrupt range check on debug exception
  powerpc: Update tlbie/tlbiel as per ISA doc
  powerpc: Print page size info during boot
  powerpc: print both base and actual page size on hash failure
  powerpc: Fix hpte_decode to use the correct decoding for page sizes
  powerpc: Decode the pte-lp-encoding bits correctly.
  powerpc: Use encode avpn where we need only avpn values
  powerpc: Reduce PTE table memory wastage
  powerpc: Move the pte free routines from common header
  powerpc: Reduce the PTE_INDEX_SIZE
  powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format
  powerpc: New hugepage directory format
  powerpc: Don't truncate pgd_index wrongly
  powerpc: Don't hard code the size of pte page
  powerpc: Save DAR and DSISR in pt_regs on MCE
  ...
2013-05-02 10:16:16 -07:00
Brian King
88e7b167a0 pci: Set dev->dev.type in alloc_pci_dev
Set dev->dev.type in alloc_pci_dev so that archs that have their own
versions of pci_setup_device get this set properly in order to ensure
things like the boot_vga sysfs parameter get created as expected.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
2013-04-18 15:59:57 +10:00
Jiang Liu
10a9574756 PCI: Add pcibios hooks for adding and removing PCI buses
On ACPI-based platforms, the pci_slot driver creates PCI slot devices
according to information from ACPI tables by registering an ACPI PCI
subdriver.  The ACPI PCI subdriver will only be called when creating/
destroying PCI root buses, and it won't be called when hot-plugging
P2P bridges.  It may cause stale PCI slot devices after hot-removing
a P2P bridge if that bridge has associated PCI slots.  And the acpiphp
driver has the same issue too.

This patch introduces two hook points into the PCI core, which will
be invoked when creating/destroying PCI buses for PCI host and P2P
bridges.  They could be used to setup/destroy platform dependent stuff
in a unified way, both at boot time and for PCI hotplug operations.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Myron Stowe <myron.stowe@redhat.com>
2013-04-12 15:38:25 -06:00
Jiang Liu
981cf9ea9a PCI: Clean up usages of pci_bus->is_added
Now pci_bus->is_added is only used to guard invoking of
pcibios_fixup_bus() in pci_scan_child_bus(), so just set
it directly after the fixups and remove the other test
and set in pci_bus_add_devices().

[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
2013-04-12 15:38:25 -06:00
Bjorn Helgaas
939de1d69c Merge branch 'pci/yinghai-root-bus-hotplug' into next
* pci/yinghai-root-bus-hotplug:
  PCI: Put pci_dev in device tree as early as possible
  PCI: Skip attaching driver in device_add()
  PCI: acpiphp: Keep driver loaded even if no slots found
  PCI/ACPI: Print info if host bridge notify handler installation fails
  PCI: acpiphp: Move host bridge hotplug to pci_root.c
  PCI/ACPI: acpiphp: Rename alloc_acpiphp_hp_work() to alloc_acpi_hp_work()
  PCI: Make device create/destroy logic symmetric
  PCI: Fix reference count leak in pci_dev_present()
  PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
  PCI: Add root bus children dev's res to fail list
  PCI: acpiphp: Add is_hotplug_bridge detection

Conflicts:
	drivers/pci/pci.h
2013-01-26 17:35:58 -07:00
Bjorn Helgaas
14b5cb37cc Merge branch 'pci/yijing-ari' into next
* pci/yijing-ari:
  PCI: shpchp: Iterate over all devices in slot, not functions 0-7
  PCI: sgihp: Iterate over all devices in slot, not functions 0-7
  PCI: cpcihp: Iterate over all devices in slot, not functions 0-7
  PCI: pciehp: Iterate over all devices in slot, not functions 0-7
  PCI: Consolidate "next-function" functions
  PCI: Rename pci_enable_ari() to pci_configure_ari()
  PCI: Enable ARI if dev and upstream bridge support it; disable otherwise
2013-01-26 17:27:36 -07:00
Yinghai Lu
4f535093cf PCI: Put pci_dev in device tree as early as possible
We want to put pci_dev structs in the device tree as soon as possible so
for_each_pci_dev() iteration will not miss them, but driver attachment
needs to be delayed until after pci_assign_unassigned_resources() to make
sure all devices have resources assigned first.

This patch moves device registering from pci_bus_add_devices() to
pci_device_add(), which happens earlier, leaving driver attachment in
pci_bus_add_devices().

It also removes unattached child bus handling in pci_bus_add_devices().
That's not needed because child bus via pci_add_new_bus() is already
in parent bus children list.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-25 16:22:37 -07:00
Jiang Liu
e723f0b4f4 PCI: Make device create/destroy logic symmetric
According to device model documentation, the way to create/destroy PCI
devices should be symmetric.  The rule is to either use
  1) device_register()/device_unregister()
or
  2) device_initialize()/device_add()/device_del()/put_device().

So change PCI core logic to follow the rule and get rid of the redundant
pci_dev_get()/pci_dev_put() pair.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-25 14:42:06 -07:00
Yinghai Lu
7629d19a4d PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
Otherwise irq_desc for PCI bridge with hot-added IOAPIC may not be
allocated on the local node.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-01-25 13:45:04 -07:00
Yijing Wang
b1bd58e448 PCI: Consolidate "next-function" functions
There are several next_fn functions (no_next_fn, next_trad_fn,
next_ari_fn); consolidate them in next_fn() to simplify the code.

[bhelgaas: make next_fn() static, rework control flow]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-01-25 09:21:10 -07:00
Yijing Wang
31ab247623 PCI: Rename pci_enable_ari() to pci_configure_ari()
pci_enable_ari() now supports enabling or disabling ARI forwarding.  So
rename pci_enable_ari() to pci_configure_ari() for easy understanding.

No functional change.

[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-01-25 09:21:10 -07:00
Rafael J. Wysocki
6c0cc950ae ACPI / PCI: Set root bridge ACPI handle in advance
The ACPI handles of PCI root bridges need to be known to
acpi_bind_one(), so that it can create the appropriate
"firmware_node" and "physical_node" files for them, but currently
the way it gets to know those handles is not exactly straightforward
(to put it lightly).

This is how it works, roughly:

  1. acpi_bus_scan() finds the handle of a PCI root bridge,
     creates a struct acpi_device object for it and passes that
     object to acpi_pci_root_add().

  2. acpi_pci_root_add() creates a struct acpi_pci_root object,
     populates its "device" field with its argument's address
     (device->handle is the ACPI handle found in step 1).

  3. The struct acpi_pci_root object created in step 2 is passed
     to pci_acpi_scan_root() and used to get resources that are
     passed to pci_create_root_bus().

  4. pci_create_root_bus() creates a struct pci_host_bridge object
     and passes its "dev" member to device_register().

  5. platform_notify(), which for systems with ACPI is set to
     acpi_platform_notify(), is called.

So far, so good.  Now it starts to be "interesting".

  6. acpi_find_bridge_device() is used to find the ACPI handle of
     the given device (which is the PCI root bridge) and executes
     acpi_pci_find_root_bridge(), among other things, for the
     given device object.

  7. acpi_pci_find_root_bridge() uses the name (sic!) of the given
     device object to extract the segment and bus numbers of the PCI
     root bridge and passes them to acpi_get_pci_rootbridge_handle().

  8. acpi_get_pci_rootbridge_handle() browses the list of ACPI PCI
     root bridges and finds the one that matches the given segment
     and bus numbers.  Its handle is then used to initialize the
     ACPI handle of the PCI root bridge's device object by
     acpi_bind_one().  However, this is *exactly* the ACPI handle we
     started with in step 1.

Needless to say, this is quite embarassing, but it may be avoided
thanks to commit f3fd0c8 (ACPI: Allow ACPI handles of devices to be
initialized in advance), which makes it possible to initialize the
ACPI handle of a device before passing it to device_register().

Accordingly, add a new __weak routine, pcibios_root_bridge_prepare(),
defaulting to an empty implementation that can be replaced by the
interested architecutres (x86 and ia64 at the moment) with functions
that will set the root bridge's ACPI handle before its dev member is
passed to device_register().  Make both x86 and ia64 provide such
implementations of pcibios_root_bridge_prepare() and remove
acpi_pci_find_root_bridge() and acpi_get_pci_rootbridge_handle() that
aren't necessary any more.

Included is a fix for breakage on systems with non-ACPI PCI host
bridges from Bjorn Helgaas.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-01-13 17:14:28 -07:00
Rafael J. Wysocki
d2e5f0c16a ACPI / PCI: Rework the setup and cleanup of device wakeup
Currently, the ACPI wakeup capability of PCI devices is set up
in two different places, partially in acpi_pci_bind() where
runtime wakeup is initialized and partially in
platform_pci_wakeup_init(), where system wakeup is initialized.
The cleanup is only done in acpi_pci_unbind() and it only covers
runtime wakeup.

Use the new .setup() and .cleanup() callbacks in struct acpi_bus_type
to consolidate that code and do the setup and the cleanup each in one
place.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
2013-01-03 13:09:41 +01:00
Linus Torvalds
193c0d6825 PCI changes for the v3.8 merge window:
Host bridge hotplug:
     - Untangle _PRT from struct pci_bus (Bjorn Helgaas)
     - Request _OSC control before scanning root bus (Taku Izumi)
     - Assign resources when adding host bridge (Yinghai Lu)
     - Remove root bus when removing host bridge (Yinghai Lu)
     - Remove _PRT during hot remove (Yinghai Lu)
 
   SRIOV
     - Add sysfs knobs to control numVFs (Don Dutile)
 
   Power management
     - Notify devices when power resource turned on (Huang Ying)
 
   Bug fixes
     - Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
     - Keep runtime PM enabled for unbound PCI devices (Huang Ying)
     - Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
     - Fix xen frontend shutdown issue (David Vrabel)
     - Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
 
   Miscellaneous
     - Add GPL license for drivers/pci/ioapic (Andrew Cooks)
     - Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
     - NumaChip remote PCI support (Daniel Blueman)
     - Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
     - Convert dev_printk() to dev_info(), etc (Joe Perches)
     - Add support for non PCI BAR ROM data (Matthew Garrett)
     - Add x86 support for host bridge translation offset (Mike Yoknis)
     - Report success only when every driver supports AER (Vijay Pandarathil)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.10 (GNU/Linux)
 
 iQIcBAABAgAGBQJQyKwSAAoJEPGMOI97Hn6zScgQAJZK2VDfCv74mKrgSDNokIzH
 5nVDrc9AHKJm7CUODs6keJK5d4TD/za3Zao68zrYHsJJKes2ni2Z3W34HP2RXKK2
 eOmePXOHYPPZMlimP9r9cVxNu1ZJCyp/yWSBcsPF4zUgWhBWLRaSj85I049gQ0sz
 +05nZYfLjVd3HNiaXsG4CQyMrNF46XEsLhF9vs+Nr2GHPwrpzhfScgYv63oDS86C
 3ICKsjmiRUZcNelxIFYmyxa5u89QdW5XHjzc9eHGQuus24Vxw+TZzsdfc17sUJEE
 HTyXY+RjDpOVhdtwwUjrCEOiyZYvy3g9+3sKxoxgt/76ghdUaR7fxITwB97qVMFD
 T0ESlKjSV/Qv5QYdyy5uP4zwNs/PXCWXkTg/L1m71F30BxKWDa7tgiA6uK7Z7fl5
 1aokKBdk3mtJJJIDJG1YkxPXx/JItTGCNYrx7CcFj49rSjrUWLQdmrYahersRIsB
 3wiD2xTi9e4dXeP/+VGzGOWB/sHk+73jvrvZe/REa1FCnMINDz4+9V9WaGROMqyq
 MQ8kX0KfYcNVNxy1GOXjU5wLpMN/t/QbvI7gwzRP1DAUCJPoOgFy7AjvSTVG3zuy
 8CtdOFttVkUn5dqsbQR0gVbyQVTS3PGSKz5XC/s8kVDWhja0xZTBYwrskM/4zdSD
 Xf48OyYV5EjpC3FYUSiU
 =OE3Q
 -----END PGP SIGNATURE-----

Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI update from Bjorn Helgaas:
 "Host bridge hotplug:
   - Untangle _PRT from struct pci_bus (Bjorn Helgaas)
   - Request _OSC control before scanning root bus (Taku Izumi)
   - Assign resources when adding host bridge (Yinghai Lu)
   - Remove root bus when removing host bridge (Yinghai Lu)
   - Remove _PRT during hot remove (Yinghai Lu)

  SRIOV
    - Add sysfs knobs to control numVFs (Don Dutile)

  Power management
   - Notify devices when power resource turned on (Huang Ying)

  Bug fixes
   - Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
   - Keep runtime PM enabled for unbound PCI devices (Huang Ying)
   - Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
   - Fix xen frontend shutdown issue (David Vrabel)
   - Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)

  Miscellaneous
   - Add GPL license for drivers/pci/ioapic (Andrew Cooks)
   - Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
   - NumaChip remote PCI support (Daniel Blueman)
   - Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
     Han)
   - Convert dev_printk() to dev_info(), etc (Joe Perches)
   - Add support for non PCI BAR ROM data (Matthew Garrett)
   - Add x86 support for host bridge translation offset (Mike Yoknis)
   - Report success only when every driver supports AER (Vijay
     Pandarathil)"

Fix up trivial conflicts.

* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
  PCI: Use phys_addr_t for physical ROM address
  x86/PCI: Add NumaChip remote PCI support
  ath9k: Use standard #defines for PCIe Capability ASPM fields
  iwlwifi: Use standard #defines for PCIe Capability ASPM fields
  iwlwifi: collapse wrapper for pcie_capability_read_word()
  iwlegacy: Use standard #defines for PCIe Capability ASPM fields
  iwlegacy: collapse wrapper for pcie_capability_read_word()
  cxgb3: Use standard #defines for PCIe Capability ASPM fields
  PCI: Add standard PCIe Capability Link ASPM field names
  PCI/portdrv: Use PCI Express Capability accessors
  PCI: Use standard PCIe Capability Link register field names
  x86: Use PCI setup data
  PCI: Add support for non-BAR ROMs
  PCI: Add pcibios_add_device
  EFI: Stash ROMs if they're not in the PCI BAR
  PCI: Add and use standard PCI-X Capability register names
  PCI/PM: Keep runtime PM enabled for unbound PCI devices
  xen-pcifront: Handle backend CLOSED without CLOSING
  PCI: SRIOV control and status via sysfs (documentation)
  PCI/AER: Report success only when every device has AER-aware driver
  ...
2012-12-13 12:14:47 -08:00
Bjorn Helgaas
27e1c8ee01 Merge branch 'pci/bjorn-pcie-cap' into next
* pci/bjorn-pcie-cap:
  ath9k: Use standard #defines for PCIe Capability ASPM fields
  iwlwifi: Use standard #defines for PCIe Capability ASPM fields
  iwlwifi: collapse wrapper for pcie_capability_read_word()
  iwlegacy: Use standard #defines for PCIe Capability ASPM fields
  iwlegacy: collapse wrapper for pcie_capability_read_word()
  cxgb3: Use standard #defines for PCIe Capability ASPM fields
  PCI: Add standard PCIe Capability Link ASPM field names
  PCI/portdrv: Use PCI Express Capability accessors
  PCI: Use standard PCIe Capability Link register field names
  PCI: Add and use standard PCI-X Capability register names
2012-12-07 12:11:52 -07:00
Bjorn Helgaas
231afea189 PCI: Use standard PCIe Capability Link register field names
Use the standard #defines for PCIe Link Status and Capability registers
rather than bare numbers.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-12-07 11:16:30 -07:00
Bjorn Helgaas
7793eeabc8 PCI: Add and use standard PCI-X Capability register names
Add and use #defines for PCI-X Capability registers and fields.
Note that the PCI-X Capability has a different layout for
type 0 (endpoint) and type 1 (bridge) devices.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-12-05 13:51:17 -07:00
Bill Pemberton
15856ad50b PCI: Remove __dev* markings
CONFIG_HOTPLUG is going away as an option so __devexit_p, __devint,
__devinitdata, __devinitconst, and _devexit are no longer needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28 13:16:47 -08:00
Bill Pemberton
b40b97ae73 PCI: Remove CONFIG_HOTPLUG ifdefs
Remove conditional code based on CONFIG_HOTPLUG being false.  It's
always on now in preparation of it going away as an option.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28 12:53:46 -08:00
Bjorn Helgaas
f9c15b429a Merge branch 'pci/don-sriov' into next
* pci/don-sriov:
  PCI: Remove useless "!dev" tests
  PCI: Use spec names for SR-IOV capability fields
  PCI: Provide method to reduce the number of total VFs supported
  PCI: SRIOV control and status via sysfs
  PCI: Use is_visible() with boot_vga attribute for pci_dev
  PCI: Add pci_device_type to pdev's device struct
2012-11-13 14:33:32 -07:00
Yinghai Lu
4e15c46bdc PCI: Add pci_device_type to pdev's device struct
Need type filled in device structure so it can be used for visible
attribute control in sysfs for pci_dev.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-11-09 20:07:31 -07:00
Yinghai Lu
e164f658f2 PCI: Move out pci_enable_bridges out of assign_unsigned_bus_res
So could use assign_unassigned_bus_res pci root bus add

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-11-03 16:20:30 -06:00
Yinghai Lu
a5213a3194 PCI: Move pci_rescan_bus() back to probe.c
We have pci_assign_unassigned_bus_resources() in as global function now.

Move pci_rescan_bus() back to probe.c where it should be.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-11-03 16:20:07 -06:00
Bjorn Helgaas
78c8f84302 Merge branch 'pci/yinghai-misc' into next 2012-09-24 17:24:11 -06:00
Yinghai Lu
1965f66e7d PCI: Check P2P bridge for invalid secondary/subordinate range
For bridges with "secondary > subordinate", i.e., invalid bus number
apertures, we don't enumerate anything behind the bridge unless the
user specified "pci=assign-busses".

This patch makes us automatically try to reassign the downstream bus
numbers in this case (just for that bridge, not for all bridges as
"pci=assign-busses" does).

We don't discover all the devices on the Intel DP43BF motherboard
without this change (or "pci=assign-busses") because its BIOS configures
a bridge as:

    pci 0000:00:1e.0: PCI bridge to [bus 20-08] (subtractive decode)

[bhelgaas: changelog, change message to dev_info]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18412
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=625754
Reported-by: Brian C. Huffman <bhuffman@graze.net>
Reported-by: VL <vl.homutov@gmail.com>
Tested-by: VL <vl.homutov@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
2012-09-18 16:47:54 -06:00
Bjorn Helgaas
6dabee73d4 Merge branch 'pci/trivial' into next
* pci/trivial:
  PCI: Drop duplicate const in DECLARE_PCI_FIXUP_SECTION
  PCI: Drop bogus default from ARCH_SUPPORTS_MSI
  PCI: cpqphp: Remove unreachable path
  PCI: Remove bus number resource debug messages
  PCI/AER: Print completion message at KERN_INFO to match starting message
  PCI: Fix drivers/pci/pci.c kernel-doc warnings
2012-09-13 09:08:02 -06:00
Bjorn Helgaas
78890b5989 Merge commit 'v3.6-rc5' into next
* commit 'v3.6-rc5': (1098 commits)
  Linux 3.6-rc5
  HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
  Remove user-triggerable BUG from mpol_to_str
  xen/pciback: Fix proper FLR steps.
  uml: fix compile error in deliver_alarm()
  dj: memory scribble in logi_dj
  Fix order of arguments to compat_put_time[spec|val]
  xen: Use correct masking in xen_swiotlb_alloc_coherent.
  xen: fix logical error in tlb flushing
  xen/p2m: Fix one-off error in checking the P2M tree directory.
  powerpc: Don't use __put_user() in patch_instruction
  powerpc: Make sure IPI handlers see data written by IPI senders
  powerpc: Restore correct DSCR in context switch
  powerpc: Fix DSCR inheritance in copy_thread()
  powerpc: Keep thread.dscr and thread.dscr_inherit in sync
  powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
  powerpc/powernv: Always go into nap mode when CPU is offline
  powerpc: Give hypervisor decrementer interrupts their own handler
  powerpc/vphn: Fix arch_update_cpu_topology() return value
  ARM: gemini: fix the gemini build
  ...

Conflicts:
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
	drivers/rapidio/devices/tsi721.c
2012-09-13 08:41:01 -06:00
Bjorn Helgaas
f8ba65e8fb PCI: Remove bus number resource debug messages
These messages don't seem to add much value.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-24 15:05:06 -06:00
Bjorn Helgaas
0ff9514b57 PCI: Don't print anything while decoding is disabled
If we try to print to the console device while its decoding is disabled,
the system will hang.

Reported-and-tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Olof Johansson <olof@lixom.net>
2012-08-23 10:53:08 -06:00
Jiang Liu
59875ae489 PCI/core: Use PCI Express Capability accessors
Use PCI Express Capability access functions to simplify core.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-23 09:41:37 -06:00
Yijing Wang
b2ef39be57 PCI: Remove unused field pcie_type from struct pci_dev
With introduction of pci_pcie_type(), pci_dev->pcie_type field becomes
redundant, so remove it.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-23 09:41:05 -06:00
Yijing Wang
62f87c0e31 PCI: Introduce pci_pcie_type(dev) to replace pci_dev->pcie_type
Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-23 09:40:57 -06:00
Yijing Wang
786e22885d PCI: Add pcie_flags_reg to cache PCIe capabilities register
Since PCI Express Capabilities Register is read only, cache its value
into struct pci_dev to avoid repeatedly calling pci_read_config_*().

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-20 22:32:20 +08:00
Bjorn Helgaas
6ee53f4c38 Merge branch 'pci/bjorn-p2p-bridge-windows' into next
* pci/bjorn-p2p-bridge-windows:
  sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
  PCI: support sizing P2P bridge I/O windows with 1K granularity
  PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
  PCI: allow P2P bridge windows starting at PCI bus address zero

Conflicts:
	drivers/pci/probe.c
	include/linux/pci.h
2012-07-10 08:36:09 -06:00
Bjorn Helgaas
d68e70c6e5 Merge branch 'pci/bjorn-disable-decode' into next
* pci/bjorn-disable-decode:
  PCI: disable MEM decoding while updating 64-bit MEM BARs
  PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
2012-07-09 21:02:44 -06:00
Bjorn Helgaas
2b28ae1912 PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
9d265124d0 and 15a260d53f added quirks for P2P bridges that support
I/O windows that start/end at 1K boundaries, not just the 4K boundaries
defined by the PCI spec.  For details, see the IOBL_ADR register and the
EN1K bit in the CNF register in the Intel 82870P2 (P64H2).

These quirks complicate the code that reads P2P bridge windows
(pci_read_bridge_io() and pci_cfg_fake_ranges()) because the bridge
I/O resource is updated in the HEADER quirk, in pci_read_bridge_io(),
in pci_setup_bridge(), and again in the FINAL quirk.  This is confusing
and makes it impossible to reassign the bridge windows after FINAL
quirks are run.

This patch adds support for 1K windows in the generic paths, so the
HEADER quirk only has to enable this support.  The FINAL quirk, which
used to undo damage done by pci_setup_bridge(), is no longer needed.

This removes "if (!res->start) res->start = ..." from pci_read_bridge_io();
that was part of 9d265124d0 to avoid overwriting the resource filled in
by the quirk.  Since pci_read_bridge_io() itself now knows about
granularity, the quirk no longer updates the resource and this test is no
longer needed.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-09 19:52:04 -06:00
Bjorn Helgaas
bbffe43524 PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
After 253d2e5498, we disable MEM and IO decoding for most devices while we
size 32-bit BARs.  However, we restore the original COMMAND register before
we size the upper 32 bits of 64-bit BARs, so we can still cause a conflict.

This patch waits to restore the original COMMAND register until we're
completely finished sizing the BAR.

Reference: https://lkml.org/lkml/2007/8/25/154
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-09 19:49:24 -06:00
Bjorn Helgaas
5dde383e2e PCI: allow P2P bridge windows starting at PCI bus address zero
cd81e1ea1a added checks that prevent us from using P2P bridge windows
that start at PCI bus address zero.  The reason was to "prevent us from
overwriting resources that are unassigned."

But generic code should allow address zero in both BARs and bridge
windows, so I think that commit was a mistake.

Windows at bus address zero are legal and likely to exist on machines with
an offset between bus addresses and CPU addresses.  For example, in the
following hypothetical scenario, the bridge at 00:01.0 has a window at bus
address zero and the device at 01:00.0 has a BAR at bus address zero, and
I think both are perfectly valid:

    PCI host bridge to bus 0000:00
    pci_bus 0000:00: root bus resource [mem 0x100000000-0x1ffffffff] (bus address [0x00000000-0xffffffff])
    pci 0000:00:01.0: PCI bridge to [bus 01]
    pci 0000:00:01.0:   bridge window [mem 0x100000000-0x100ffffff]
    pci 0000:01:00.0: reg 10: [mem 0x100000000-0x100ffffff]

Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-07-09 13:38:41 -06:00
Bjorn Helgaas
0f6662a49b Merge branch 'topic/bjorn-trivial' into next
* topic/bjorn-trivial:
  PCI: remove useless pcix_set_mmrbc() dev->bus check
  PCI: acpiphp: check whether _ADR evaluation succeeded
  PCI: shpchp: remove dead code
  PCI: fix P2P bridge I/O port window sign extension
  PCI: fix upstream P2P bridge checks when enabling OBFF and LTR
  PCI: use __weak consistently
  PCI: cleanup assign_requested_resources_sorted() kernel-doc warning
  sparc/PCI: remove unused pcibios_assign_resource() definition
2012-06-22 15:32:50 -06:00
Bjorn Helgaas
8f38eaca55 PCI: fix P2P bridge I/O port window sign extension
On P2P bridges with 32-bit I/O decoding, we incorrectly sign-extended
windows starting at 0x80000000 or above.  In "base |= (io_base_hi << 16)",
"io_base_hi" is promoted to a signed int before being extended to an
unsigned long.

This would cause a window starting at I/O address 0x80000000 to be
treated as though it started at 0xffffffff80008000 instead, which
should cause "no compatible bridge window" errors when we enumerate
devices using that I/O space.

The mmio and mmio_pref casts are not strictly necessary, but without
them, correctness depends on the types of the PCI_MEMORY_RANGE_MASK and
PCI_PREF_RANGE_MASK constants, which are not obvious from reading the
local code.

Found by Coverity (CID 138747 and CID 138748).

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-20 17:28:53 -06:00
Yinghai Lu
bc76b7310a PCI: insert busn_res for child bus
Now we can insert busn_res now, after all root bus's get inserted.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:25 -06:00
Yinghai Lu
857c3b668a PCI: add default busn_res for pci_scan_bus()
also do not need to shrink busn_res.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:23 -06:00
Yinghai Lu
67cdc82728 PCI: add default busn_resource
We need to put into the resources list for legacy system.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:23 -06:00
Yinghai Lu
4d99f52423 PCI: checking busn_res in pci_scan_root_bus()
Some callers do not supply the bus number aperture, usually because they do
not know the end.  In this case, we assume the aperture extends from the
root bus number to bus 255, scan the bus, and shrink the bus number
resource so it ends at the largest bus number we found.

This is obviously not correct because the actual end of the aperture may
well be larger than the largest bus number we found.  But I guess it's all
we have for now.

Also print out one info about that, so we could find out which path
does not have busn_res in resources list.

[bhelgaas: changelog, _safe iterator unnecessary, use %pR format for bus]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
2012-06-13 15:42:23 -06:00
Yinghai Lu
f848ffb104 PCI: insert busn_res in pci_create_root_bus()
That busn_res is from resources list.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:22 -06:00
Yinghai Lu
98a3583107 PCI: add busn_res operation functions
Will use them insert/update busn res in pci_bus struct.

[bhelgaas: print conflicting entry if insertion fails]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:22 -06:00
Yinghai Lu
5cc62c2022 PCI: build a bus number resource tree for every domain
This adds get_pci_domain_busn_res(), which returns the root of the
bus number resource tree for a domain, creating it if necessary.
We will later populate the tree with the bus numbers used by host
bridges and P2P bridges in the domain.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:22 -06:00
Yinghai Lu
b918c62e08 PCI: replace struct pci_bus secondary/subordinate with busn_res
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res.  Later we'll build a resource tree of these
bus numbers.

[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-06-13 15:42:22 -06:00
Bjorn Helgaas
0cbaa57d82 Merge branch 'topic/stratus' into next 2012-05-07 09:23:27 -06:00
Bjorn Helgaas
284f5f9dba PCI: work around Stratus ftServer broken PCIe hierarchy
A PCIe downstream port is a P2P bridge.  Its secondary interface is
a link that should lead only to device 0 (unless ARI is enabled)[1], so
we don't probe for non-zero device numbers.

Some Stratus ftServer systems have a PCIe downstream port (02:00.0) that
leads to both an upstream port (03:00.0) and a downstream port (03:01.0),
and 03:01.0 has important devices below it:

  [0000:02]-+-00.0-[03-3c]--+-00.0-[04-09]--...
                            \-01.0-[0a-0d]--+-[USB]
                                            +-[NIC]
                                            +-...

Previously, we didn't enumerate device 03:01.0, so USB and the network
didn't work.  This patch adds a DMI quirk to scan all device numbers,
not just 0, below a downstream port.

Based on a patch by Prarit Bhargava.

[1] PCIe spec r3.0, sec 7.3.1

CC: Myron Stowe <mstowe@redhat.com>
CC: Don Dutile <ddutile@redhat.com>
CC: James Paradis <james.paradis@stratus.com>
CC: Matthew Wilcox <matthew.r.wilcox@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 15:21:02 -06:00
Yinghai Lu
4fa2649a01 PCI: add host bridge release support
We need a hook to release host bridge resources allocated when creating
root bus.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 14:52:43 -06:00
Yinghai Lu
7b54366358 PCI: add generic device into pci_host_bridge struct
Use that device for pci_root_bus bridge pointer.

Use pci_release_bus_bridge_dev() to release allocated pci_host_bridge in
remove path.

Use root bus bridge pointer to get host bridge pointer instead of searching
host bridge list.  That leaves the host bridge list unused, so remove it.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 13:53:42 -06:00
Yinghai Lu
610929e119 PCI: move host bridge-related code to host-bridge.c
Move host bridge-related code from probe.c to a new host-bridge.c.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-04-30 13:36:14 -06:00
Bjorn Helgaas
cf48fb6a2b PCI: fix bridge I/O window bus-to-resource conversion
In 5bfa14ed9f, I forgot to initialize res2.flags before calling
pcibios_bus_to_resource(), which depends on the resource type to locate the
correct aperture.  This bug won't hurt x86, which currently never has an
offset between bus and CPU addresses, but will affect other architectures.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-03-20 10:41:27 -07:00
Yinghai Lu
2069ecfbe1 PCI: Move "pci reassigndev resource alignment" out of quirks.c
This isn't really a quirk; calling it directly from pci_add_device makes
more sense.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-24 14:37:26 -08:00
Bjorn Helgaas
fb127cb9de PCI: collapse pcibios_resource_to_bus
Everybody uses the generic pcibios_resource_to_bus() supplied by the core
now, so remove the ARCH_HAS_GENERIC_PCI_OFFSETS used during conversion.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-02-23 20:19:04 -07:00
Bjorn Helgaas
36a66cd6fd PCI: add generic pcibios_resource_to_bus()
This replaces the generic versions of pcibios_resource_to_bus() and
pcibios_bus_to_resource() in asm-generic/pci.h with versions that use
pci_resource_to_bus() and pci_bus_to_resource().

The replacements are equivalent except that they can apply host
bridge window offsets when the arch has supplied them by using
pci_add_resource_offset().

Each arch can convert to using pci_add_resource_offset() individually by
removing its device resource fixups from pcibios_fixup_bus() and supplying
ARCH_HAS_GENERIC_PCI_OFFSETS.  ARCH_HAS_GENERIC_PCI_OFFSETS can be removed
after all have converted.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-02-23 20:19:00 -07:00
Bjorn Helgaas
5bfa14ed9f PCI: convert bus addresses to resource when reading BARs
Some PCI host bridges translate CPU addresses to PCI bus addresses.
Previously, we initialized pci_dev resources with PCI bus addresses,
then converted them to CPU addresses later in arch-specific code
(pcibios_fixup_resources()), which leaves a window of time where the
pci_dev resources are incorrect.

This patch adds support in the core for this address translation.
When the arch creates the root bus, it can supply the host bridge
address translation information, and the core can use it to set the
pci_dev resources correctly from the beginning.

This gives us a way to fix the problem that quirks that run between device
discovery and pcibios_fixup_resources() fail because they use pci_dev
resources that haven't been converted.  The reference below is to one
such problem that affected ARM and ia64.

Note that this patch has no effect until an arch starts using
pci_add_resource_offset() with a non-zero offset: before that, all
all host bridge windows have a zero offset and pci_bus_to_resource()
copies the pci_bus_region directly to the struct resource.

Reference: https://lkml.org/lkml/2009/10/12/405
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-02-23 20:19:00 -07:00
Bjorn Helgaas
0efd5aab41 PCI: add struct pci_host_bridge_window with CPU/bus address offset
Some PCI host bridges apply an address offset, so bus addresses on PCI are
different from CPU addresses.  This patch adds a way for architectures to
tell the PCI core about this offset.  For example:

    LIST_HEAD(resources);
    pci_add_resource_offset(&resources, host->io_space, host->io_offset);
    pci_add_resource_offset(&resources, host->mem_space, host->mem_offset);
    pci_scan_root_bus(parent, bus, ops, sysdata, &resources);

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-02-23 20:19:00 -07:00
Bjorn Helgaas
5a21d70dbd PCI: add struct pci_host_bridge and a list of all bridges found
This adds a list of all PCI host bridges we find and a way to look up
the host bridge from a pci_dev.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-02-23 20:18:59 -07:00
Bjorn Helgaas
a5390aa6dc PCI: don't publish new root bus until it's fully initialized
When pci_create_root_bus() adds the new struct pci_bus to the global
pci_root_buses list, the bus becomes visible to other parts of the
kernel, so it should be fully initialized.

This patch delays adding the bus to the pci_root_buses list until after
all the struct pci_bus initialization is finished.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-02-23 20:18:59 -07:00
Yinghai Lu
f796841e49 PCI: fix memleak for pci dev removing during hotplug
unreferenced object 0xffff880276d17700 (size 64):
  comm "swapper/0", pid 1, jiffies 4294897182 (age 3976.028s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 18 f9 de 76 02 88 ff ff  ...........v....
    10 00 00 00 0e 00 00 00 0f 28 40 00 00 00 00 00  .........(@.....
  backtrace:
    [<ffffffff81c8aede>] kmemleak_alloc+0x26/0x43
    [<ffffffff811385f0>] __kmalloc+0x121/0x183
    [<ffffffff813cf821>] pci_add_cap_save_buffer+0x35/0x7c
    [<ffffffff813d12b7>] pci_allocate_cap_save_buffers+0x1d/0x65
    [<ffffffff813cdb52>] pci_device_add+0x92/0xf1
    [<ffffffff81c8afe6>] pci_scan_single_device+0x9f/0xa1
    [<ffffffff813cdbd2>] pci_scan_slot.part.20+0x21/0x106
    [<ffffffff813cdce2>] pci_scan_slot+0x2b/0x35
    [<ffffffff81c8dae4>] __pci_scan_child_bus+0x51/0x107
    [<ffffffff81c8d75b>] pci_scan_bridge+0x376/0x6ae
    [<ffffffff81c8db60>] __pci_scan_child_bus+0xcd/0x107
    [<ffffffff81c8dbab>] pci_scan_child_bus+0x11/0x2a
    [<ffffffff81cca58c>] pci_acpi_scan_root+0x18b/0x21c
    [<ffffffff81c916be>] acpi_pci_root_add+0x1e1/0x42a
    [<ffffffff81406210>] acpi_device_probe+0x50/0x190
    [<ffffffff814a0227>] really_probe+0x99/0x126

Need to free saved_buffer for capabilities.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-23 12:08:53 -08:00
Yinghai Lu
2dd8ba921d PCI: Fix device class print out
Found debug print of class is shifted.

| pci 0000:f8:15.2: [8086:2b56] type 0 class 0x000600

Code is trying to print class with 6 digits, but use shifted class with
4 digits valid value as variable.

Change to original dev->class directly.

Also remove not needed calculating of local variable class, because it
will be updated after pci_fixup_device(pci_fixup_early...)

Also unify type print out when class and header is not matched.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-23 12:05:59 -08:00
Yinghai Lu
efdc87dab1 PCI: Separate pci_bus_read_dev_vendor_id from pci_scan_device
We can reuse it for pciehp probing.

-v2: according to Kenji, fix crs timeout checking, and export the function
     for later use when pciehp is compiled as a module.

Suggested-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-14 08:44:59 -08:00
Yinghai Lu
9b03088f95 PCI: Make pci_rescan_bus handle add_list
This allows us to allocate resources to hotplug bridges during
remove/rescan.

We need to move the function to setup-bus.c so it can use
__pci_bus_size_bridges and __pci_bus_assign_resources directly to take
the add_list resource tracking list.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-14 08:44:53 -08:00
Yinghai Lu
2f320521a0 PCI: Make rescan bus increase bridge resource size if needed
Current rescan will not touch bridge MMIO and IO.

Try to reuse pci_assign_unassigned_bridge_resources(bridge) to update bridge
resources, if child devices need more resources.

Only do that for bridges whose children are all removed already; i.e. don't
release resources that could already be in use by drivers on child devices.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-14 08:44:53 -08:00
Yinghai Lu
71f6bd4a23 PCI: workaround hard-wired bus number V2
Fixes PCI device detection on IBM xSeries IBM 3850 M2 / x3950 M2
when using ACPI resources (_CRS).
This is default, a manual workaround (without this patch)
would be pci=nocrs boot param.

V2: Add dev_warn if the workaround is hit. This should reveal
how common such setups are (via google) and point to possible
problems if things are still not working as expected.
-> Suggested by Jan Beulich.

Cc: stable@vger.kernel.org
Tested-by: garyhade@us.ibm.com
Signed-off-by: Yinghai Lu <yinghai.lu@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-02-10 11:34:42 -08:00
Bjorn Helgaas
118faafaf9 PCI: remove pci_create_bus()
All users of pci_create_bus() have been converted to pci_create_root_bus(),
so remove it.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:11:15 -08:00
Bjorn Helgaas
7e00fe2e53 PCI: deprecate pci_scan_bus_parented()
Users of pci_scan_bus_parented() should be converted to use either
    pci_scan_root_bus() (preferred, but also calls pci_bus_add_devices)
or
    pci_create_root_bus()
    pci_scan_child_bus()

Since pci_scan_bus_parented(), I'm marking it deprecated now and will
actually remove it later.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:55 -08:00
Bjorn Helgaas
1e39ae9f90 PCI: convert pci_scan_bus_parented() to use pci_create_root_bus()
This converts pci_scan_bus_parented() to use pci_create_root_bus()
instead of pci_create_bus().  The new bus still has the default (incorrect)
resources, so this patch doesn't help fix that problem, but it does remove
one more use of pci_create_bus().

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:54 -08:00
Bjorn Helgaas
de4b2f76d6 PCI: convert pci_scan_bus() to use pci_create_root_bus()
I plan to deprecate pci_scan_bus_parented(), so use pci_create_root_bus()
directly instead.  pci_scan_bus() itself will be removed as soon as all
callers are gone, so this is just an interim step.

v2: export pci_scan_bus

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:53 -08:00
Bjorn Helgaas
a2ebb82795 PCI: add pci_scan_root_bus() that accepts resource list
"Early" and "header" quirks often use incorrect bus resources because they
see the default resources assigned by pci_create_bus(), before the
architecture fixes them up (typically in pcibios_fixup_bus()).  Regions
reserved by these quirks end up with the wrong parents.

Here's the standard path for scanning a PCI root bus:

  pci_scan_bus or pci_scan_bus_parented
    pci_create_bus                     <-- A create with default resources
    pci_scan_child_bus
      pci_scan_slot
        pci_scan_single_device
          pci_scan_device
            pci_setup_device
              pci_fixup_device(early)  <-- B
          pci_device_add
            pci_fixup_device(header)   <-- C
      pcibios_fixup_bus                <-- D fill in correct resources

Early and header quirks at B and C use the default (incorrect) root bus
resources rather than those filled in at D.

This patch adds a new pci_scan_root_bus() function that sets the bus
resources correctly from a supplied list of resources.

I intend to remove pci_scan_bus() and pci_scan_bus_parented() after
fixing all callers.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:52 -08:00
Bjorn Helgaas
166c637075 PCI: add pci_create_root_bus() that accepts resource list
pci_create_bus() assigns ioport_resource and iomem_resource as the default
bus resources, i.e., the entire address space.  Architectures fix these
later, typically in pcibios_fixup_bus() or after pci_scan_bus_parented()
returns, but code that runs in the interim sees incorrect resource
information.

This patch adds a new pci_create_root_bus() that sets the bus resources
correctly from a supplied list of resources.

I intend to remove pci_create_bus() after changing all callers.

Based on original patch by Deng-Cheng Zhu.

Reference: http://www.spinics.net/lists/mips/msg41654.html
Reference: https://lkml.org/lkml/2011/8/26/88
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:51 -08:00
Bjorn Helgaas
a9d9f5276c PCI: show host bridges and root bus resources
Show the bus number and resources for every root bus we create.  This
will become more interesting when we supply the correct resources
instead of using the defaults (ioport_resource and iomem_resource).

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:51 -08:00
Zac Storer
68e35c9b0b PCI: fix a brace coding style issue in probe.c
Fixed a brace coding style issue.

Signed-off-by: Zac Storer <zac.3.14159@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2012-01-06 12:10:31 -08:00
Jon Mason
a513a99a7c PCI: Clean-up MPS debug output
Clean-up MPS debug output to make it a single line and aligned, thus
making it more readable for a large number of buses and devices in a
single system.

Suggested by Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-27 12:45:44 -07:00
Jon Mason
62f392ea5b PCI: enable MPS "performance" setting to properly handle bridge MPS
Rework the "performance" MPS option to configure the device MPS with the
smaller of the device MPSS or the bridge MPS (which is assumed to be
properly configured at this point to the largest allowable MPS based on
its parent bus).

Also, rework the MRRS setting to report an inability to set the MRRS to
a valid setting.

Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-10-27 12:45:43 -07:00
Jon Mason
5f39e6705f PCI: Disable MPS configuration by default
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults.  Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.

Also, add the option for peer to peer DMA MPS configuration.  Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another.  To work around this, simply make the system
wide MPS the smallest possible value (128B).

Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-10-04 09:52:28 -07:00
Benjamin Herrenschmidt
1a4b1a41b8 pci: Don't crash when reading mpss from root complex
In pcie_find_smpss(), we have the following statement:

 	if (dev->is_hotplug_bridge && (!list_is_singular(&dev->bus->devices) ||
	    dev->bus->self->pcie_type != PCI_EXP_TYPE_ROOT_PORT))

The problem is that at least on my machine, this gets called for the
root complex (virtual P2P bridge), and dev->bus->self is NULL since
the parent bus for this is not itself anchor to a PCI device.

This adds the necessary NULL check.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jon Mason <mason@myri.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-13 16:08:31 -07:00
Jon Mason
ed2888e906 PCI: Remove MRRS modification from MPS setting code
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices.  Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode.  Also, make pcie_bus_safe
the default procedure.

Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Simon Kirby <sim@hostway.ca>
Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-09 19:49:58 -07:00
Shyam Iyer
5307f6d5fb Fix pointer dereference before call to pcie_bus_configure_settings
Commit b03e7495a8 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.

To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.

Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-09 19:49:58 -07:00
Jon Mason
debc3b7785 PCI: export pcie_bus_configure_settings symbol
pcie_bus_configure_settings needs to be exported if the PCI hotplug
driver is being compiled as a module.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-02 08:53:00 -07:00
Jon Mason
b03e7495a8 PCI: Set PCI-E Max Payload Size on fabric
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size.  There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device.  However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.

This can be achieved two ways:

- A conservative approach is to use the smallest common denominator of
  the entire tree below a root complex for every device on that fabric.

This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.

It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.

- A more optimal way is possible, if it falls within a couple of
  constraints:
* The top-level host bridge will never generate packets larger than the
  smallest TLP (or if it can be controlled independently from its MPS at
  least)
* The device will never generate packets larger than MPS (which can be
  configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
  some additional code to specifically deal with that case

Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.

In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.

To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls.  "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.

NOTE: due to the location of the enablement, each arch will need to add
calls to this function.  This patch only enables x86.

This patch includes a number of changes recommended by Benjamin
Herrenschmidt.

Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-08-01 11:49:16 -07:00
Linus Torvalds
f85f19de90 Merge branch 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: remove printks about disabled bridge windows
  PCI: fold pci_calc_resource_flags() into decode_bar()
  PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
  PCI: correct pcie_set_readrq write size
  PCI: pciehp: change wait time for valid configuration access
  x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
  PCI: ARI is a PCIe v2 feature
  x86/PCI: quirks: Use pci_dev->revision
  PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
  PCI hotplug: cpqphp: use pci_dev->vendor
  PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
  x86/PCI: config space accessor functions should not ignore the segment argument
  PCI: Assign values to 'pci_obff_signal_type' enumeration constants
  x86/PCI: reduce severity of host bridge window conflict warnings
  PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
  PCI: PCIe AER: add aer_recover_queue
  x86/PCI: select direct access mode for mmconfig option
  PCI hotplug: Rename is_ejectable which also exists in dock.c
2011-07-29 23:35:05 -07:00
Linus Torvalds
acb41c0f92 Merge branch 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'of-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  pci/of: Consolidate pci_bus_to_OF_node()
  pci/of: Consolidate pci_device_to_OF_node()
  x86/devicetree: Use generic PCI <-> OF matching
  microblaze/pci: Move the remains of pci_32.c to pci-common.c
  microblaze/pci: Remove powermac originated cruft
  pci/of: Match PCI devices to OF nodes dynamically
2011-07-22 14:54:02 -07:00
Bjorn Helgaas
7b87c9df56 PCI: remove printks about disabled bridge windows
I don't think there's enough value in the fact of a bridge window
being disabled to justify cluttering the dmesg log with it.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-22 09:08:07 -07:00
Bjorn Helgaas
28c6821a0f PCI: fold pci_calc_resource_flags() into decode_bar()
decode_bar() and pci_calc_resource_flags() both looked at the PCI BAR
type information, and it's simpler to just do it all in one place.

decode_bar() sets IORESOURCE_IO, IORESOURCE_MEM, and IORESOURCE_MEM_64
as appropriate, so res->flags contains all the information pci_bar_type
does, so we don't need to test the pci_bar_type return value.

decode_bar() used to return pci_bar_type, which we no longer need.  We
can simplify it a bit by returning the struct resource flags rather than
updating them internally.

In pci_update_resource(), there's no need to decode the BAR type bits
again; we can just test for IORESOURCE_MEM_64 directly.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-22 09:08:01 -07:00
Bjorn Helgaas
8d6a6a4763 PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
This fixes a minor regression where broken PCI devices that use the
reserved "11" memory BAR type worked before e354597cce but not after.

The low four bits of a memory BAR are "PTT0" where P=1 for prefetchable
BARs, and TT is as follows:

  00  32-bit BAR, anywhere in lower 4GB
  01  anywhere below 1MB (reserved as of PCI 2.2)
  10  64-bit BAR
  11  reserved

Prior to e354597cce, we treated "0100" as a 64-bit BAR and all others,
including prefetchable 64-bit BARs ("1100") as 32-bit BARs.  The e354597cce
fix, which appeared in 2.6.28, treats "x1x0" as 64-bit BARs, so the
reserved "x110" types are treated as 64-bit instead of 32-bit.

This patch returns to treating the reserved "11" type as a 32-bit BAR and
adds a warning if we see it.

It also logs a note if we see a 1M BAR.  This is not a warning, because
such hardware conforms to pre-PCI 2.2 spec, but I think it's worth noting
because Linux ignores the 1M restriction if it ever has to assign the BAR.

CC: Peter Chubb <peterc@gelato.unsw.edu.au>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35952
Reported-by: Jan Zwiegers <jan@radicalsystems.co.za>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-22 09:06:58 -07:00
Tiejun Chen
b1a98b695b PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
When hot-plugging a root bridge, we always prevent assigning a bus number
that already exists. This makes sure we don't step over an existing bus.
But sometimes we only remove PCI device in PCI hieratchy of OS, i,e.

echo 1 > /sys/bus/pci/devices/.../remove

but actually don't hotplug this device out the platform, so in this case
we still should re-scan this bus to enumerate this device when re-scanning
PCI again.

Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-07-22 08:25:38 -07:00
Benjamin Herrenschmidt
98d9f30c82 pci/of: Match PCI devices to OF nodes dynamically
powerpc has two different ways of matching PCI devices to their
corresponding OF node (if any) for historical reasons. The ppc64 one
does a scan looking for matching bus/dev/fn, while the ppc32 one does a
scan looking only for matching dev/fn on each level in order to be
agnostic to busses being renumbered (which Linux does on some
platforms).

This removes both and instead moves the matching code to the PCI core
itself. It's the most logical place to do it: when a pci_dev is created,
we know the parent and thus can do a single level scan for the matching
device_node (if any).

The benefit is that all archs now get the matching for free. There's one
hook the arch might want to provide to match a PHB bus to its device
node. A default weak implementation is provided that looks for the
parent device device node, but it's not entirely reliable on powerpc for
various reasons so powerpc provides its own.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-06-08 09:08:17 +10:00
David S. Miller
5aceca9d3c PCI: Fix warning in drivers/pci/probe.c on sparc64
IO_SPACE_LIMIT is currently used in two ways:

1) As a way to mask I/O port values read out of PCI base address
   registers.  This value should be 64-bit.

2) As a value which is the upper limit for all I/O "ports" in the
   system.

On sparc64 we store the full 64-bit physical I/O address in the
resources.  For this reason we define IO_SPACE_LIMIT at a 64-bit
"all 1's".

This is the right value to use for ioport_resource.end and for the
check made in drivers/pcmcia/rsrc_nonstatic.c:adjust_io().

But in driver/pci/probe.c:__pci_read_base() we mask this against
a "u32" variable and thus get the following warning:

drivers/pci/probe.c: In function ¡__pci_read_base¢:
drivers/pci/probe.c:207: warning: large integer implicitly truncated to unsigned type

Fix this by using an explicit "u32" cast.

I considered changing sparc64 to define a 32-bit "all 1's" like
most other systems do, but this wouldn't work because the checks
in PCMCIA's rsrc_nonstatic.c would no longer be right since they
are testing against fully formed 64-bit resources.  As described
above, on sparc64 such resources will hold full 64-bit physical
I/O addresses, not bus-centric 32-bit ones.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-31 14:29:26 -07:00
Yinghai Lu
dc2c2c9dd5 PCI/sysfs: move bus cpuaffinity to class dev_attrs
Requested by Greg KH to fix a race condition in the creating of PCI bus
cpuaffinity files.

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-21 12:17:13 -07:00
Yinghai Lu
b9d320fcb6 PCI: add rescan to /sys/.../pci_bus/.../
After remove the device from /sys, we have to rescan all or
find out the bridge and access /sys../device/rescan there.

this patch add /sys/.../pci_bus/.../rescan. So user can rescan more easy.
that is more clean and easy to understand.

like after remove 0000:c4:00.0, you can rescan 0000:c4 directly.

-v2: According to Jesse, use function instead of exposing attr, so could hide
	#ifdef in header file.
     also add code to remove rescan file in remove path.
-v3: GregKH pointed out that we should use dev_attrs to avoid racing.
     So add pcibus_attrs and make it to be member of pcibus_attrs.
-v4: Change name to pcibus_dev_attrs according to GregKH

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-05-21 12:17:12 -07:00
Jesper Juhl
7c867c8899 PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
pci_add_new_bus() calls pci_alloc_child_bus() which calls pci_alloc_bus()
that allocates memory dynamically with kzalloc(). The return value of
kzalloc() is the pointer that's eventually returned from
pci_add_new_bus(), so since kzalloc() can fail and return NULL so can
pci_add_new_bus(). Thus we may end up dereferencing a NULL pointer in
drivers/pci/probe.c::pci_scan_bridge(). Seems to me we should test for
this and bail out if it happens rather than crashing.
Also removed some trailing whitespace that bugged me while looking at
this.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2011-02-08 13:08:05 -08:00
Bjorn Helgaas
2c6413aee2 PCI: log vendor/device ID always
Previously we had to have CONFIG_PCI_DEBUG=y or CONFIG_DYNAMIC_DEBUG=y
to turn on this printk, but I think the IDs are valuable enough that it's
worth putting them in the log always.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-10-17 20:03:05 -07:00
Jacob Pan
253d2e5498 PCI: disable mmio during bar sizing
It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.

A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.

Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.

Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-07-30 09:29:35 -07:00
Huang Ying
affb72c3a8 ACPI, APEI, PCIE AER, use general HEST table parsing in AER firmware_first setup
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.

Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-05-19 22:40:14 -04:00
Bjorn Helgaas
45aa23b4cb PCI: revert broken device warning
This reverts c519a5a7da.  That change added a warning about devices that
didn't respond correctly when sizing BARs, which helped diagnose broken
devices.  But the test wasn't specific enough, so it also complained about
working devices with zero-size BARs, e.g.,
https://bugzilla.kernel.org/show_bug.cgi?id=15822

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-04-22 16:13:16 -07:00
Bjorn Helgaas
c519a5a7da PCI: complain about devices that seem to be broken
If we can tell that a device isn't working correctly, we should tell
the user to make debugging easier.  Otherwise, it can take a lot of
work to determine whether the problem is in the driver, PCMCIA, PCI,
hardware, etc., as in http://bugzilla.kernel.org/show_bug.cgi?id=12006

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:36 -07:00
Bjorn Helgaas
7b8ff6da02 PCI: make disabled window printk style match the enabled ones
No functional change; this just tweaks the changes from 349e1823a405
so the new printks for disabled PCI-to-PCI bridge windows match the
ones for the enabled windows.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:35 -07:00
Bjorn Helgaas
99ddd552fe PCI: break out primary/secondary/subordinate for readability
No functional change; just add names for the primary/secondary/subordinate
bus numbers read from config space rather than repeatedly masking/shifting.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:35 -07:00
Rafael J. Wysocki
a1e4d72cd3 PM: Allow PCI devices to suspend/resume asynchronously
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).

This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-02-26 20:39:12 +01:00
Bjorn Helgaas
2fe2abf896 PCI: augment bus resource table with a list
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge.  We've increased this size
several times when the table overflowed.

But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.

This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode.  Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.

I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture.  This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:37 -08:00
Bjorn Helgaas
2adf75160b PCI: read bridge windows before filling in subtractive decode resources
No functional change; this fills in the bus subtractive decode resources
after reading the bridge window information rather than before.  Also,
print out the subtractive decode resources as we already do for the
positive decode windows.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:25 -08:00
Bjorn Helgaas
fa27b2d108 PCI: split up pci_read_bridge_bases()
No functional change; this breaks up pci_read_bridge_bases() into separate
pieces for the I/O, memory, and prefetchable memory windows, similar to how
Yinghai recently split up pci_setup_bridge() in 68e84ff3bdc.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:17 -08:00
Yinghai Lu
cd81e1ea1a PCI: reject mmio ranges starting at 0 on pci_bridge read
We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:21 -08:00
Matthew Wilcox
4fb88c1a28 PCI: Make pci_scan_slot more robust
Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty.  Fix this by exiting early from
pci_scan_slot if there is no device in the slot.

Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt.  ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:17 -08:00
Matthew Wilcox
9dfd97fe12 PCI: Add support for reporting PCIe 3.0 speeds
Add the 8.0 GT/s speed.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:19 -08:00
Matthew Wilcox
45b4cdd57e PCI: Add support for AGP in cur/max bus speed
Take advantage of some gaps in the table to fit in support for AGP speeds.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:19 -08:00
Matthew Wilcox
9be60ca049 PCI: Add support for detection of PCIe and PCI-X bus speeds
Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:18 -08:00
Matthew Wilcox
3749c51ac6 PCI: Make current and maximum bus speeds part of the PCI core
Move the max_bus_speed and cur_bus_speed into the pci_bus.  Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:17 -08:00
Matthew Wilcox
f07852d644 PCI: Rewrite pci_scan_slot
The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions.  They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all.  By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.

We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports.  These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:16 -08:00
Benjamin Herrenschmidt
bb209c8287 powerpc/pci: Add calls to set_pcie_port_type() and set_pcie_hotplug_bridge()
We are missing these when building the pci_dev from scratch off
the Open Firmware device-tree

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-01-29 16:51:10 +11:00
Chris Wright
5d990b6275 PCI: add pci_request_acs
Commit ae21ee65e8 "PCI: acs p2p upsteram
forwarding enabling" doesn't actually enable ACS.

Add a function to pci core to allow an IOMMU to request that ACS
be enabled.  The existing mechanism of using iommu_found() in the pci
core to know when ACS should be enabled doesn't actually work due to
initialization order;  iommu has only been detected not initialized.

Have Intel and AMD IOMMUs request ACS, and Xen does as well during early
init of dom0.

Cc: Allen Kay <allen.m.kay@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-12-04 16:19:24 -08:00
Kenji Kaneshige
06a1cbafb2 PCI: use pci_pcie_cap() in pci core
Use pcie_cap() instead of pci_find_capability() to get PCIe capability
offset in PCI core code. This avoids unnecessary search in PCI
configuration space.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-24 15:25:12 -08:00
Kenji Kaneshige
0efea00063 PCI: cache PCIe capability offset
There are a lot of codes that searches PCI express capability offset
in the PCI configuration space using pci_find_capability(). Caching it
in the struct pci_dev will reduce unncecessary search. This patch adds
an additional 'pcie_cap' fields into struct pci_dev, which is
initialized at pci device scan time (in set_pcie_port_type()).

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-06 13:59:02 -08:00
Bjorn Helgaas
865df576e8 PCI: improve discovery/configuration messages
This makes PCI resource management messages more consistent and adds a few
new messages to aid debugging.

Whenever we assign resources to a device, update a BAR, or change a
bridge aperture, it's worth noting it.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 13:06:44 -08:00
Bjorn Helgaas
0207c356ef PCI: replace pr_debug with dev_dbg
Since we have a struct device, we might as well use dev_printk.  Note that
both pr_debug() and dev_dbg() are completely compiled out unless DEBUG or
DYNAMIC_DEBUG is defined.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 13:06:44 -08:00
Bjorn Helgaas
c7dabef8a2 vsprintf: use %pR, %pr instead of %pRt, %pRf
Jesse accidentally applied v1 [1] of the patchset instead of v2 [2].  This
is the diff between v1 and v2.

The changes in this patch are:
    - tidied vsprintf stack buffer to shrink and compute size more
      accurately
    - use %pR for decoding and %pr for "raw" (with type and flags) instead
      of adding %pRt and %pRf

[1] http://lkml.org/lkml/2009/10/6/491
[2] http://lkml.org/lkml/2009/10/13/441

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 13:06:41 -08:00
Gabe Black
bc577d2bb9 PCI: populate subsystem vendor and device IDs for PCI bridges
Change to populate the subsystem vendor and subsytem device IDs for
PCI-PCI bridges that implement the PCI Subsystem Vendor ID capability.
Previously bridges left subsystem vendor IDs unpopulated.

Signed-off-by: Gabe Black <gabe.black@ni.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 13:06:36 -08:00
Matt Domsch
0584396157 PCI: PCIe AER: honor ACPI HEST FIRMWARE FIRST mode
Feedback from Hidetoshi Seto and Kenji Kaneshige incorporated.  This
correctly handles PCI-X bridges, PCIe root ports and endpoints, and
prints debug messages when invalid/reserved types are found in the
HEST.  PCI devices not in domain/segment 0 are not represented in
HEST, thus will be ignored.

Today, the PCIe Advanced Error Reporting (AER) driver attaches itself
to every PCIe root port for which BIOS reports it should, via ACPI
_OSC.

However, _OSC alone is insufficient for newer BIOSes.  Part of ACPI
4.0 is the new APEI (ACPI Platform Error Interfaces) which is a way
for OS and BIOS to handshake over which errors for which components
each will handle.  One table in ACPI 4.0 is the Hardware Error Source
Table (HEST), where BIOS can define that errors for certain PCIe
devices (or all devices), should be handled by BIOS ("Firmware First
mode"), rather than be handled by the OS.

Dell PowerEdge 11G server BIOS defines Firmware First mode in HEST, so
that it may manage such errors, log them to the System Event Log, and
possibly take other actions.  The aer driver should honor this, and
not attach itself to devices noted as such.

Furthermore, Kenji Kaneshige reminded us to disallow changing the AER
registers when respecting Firmware First mode.  Platform firmware is
expected to manage these, and if changes to them are allowed, it could
break that firmware's behavior.

The HEST parsing code may be replaced in the future by a more
feature-rich implementation.  This patch provides the minimum needed
to prevent breakage until that implementation is available.

Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 13:06:25 -08:00
Michael S. Tsirkin
1ed6743918 PCI: fix nit in ROM BAR size probing
When probing for ROM BAR size, we should not change bits 1:10 in this
BAR, because these bits are marked as "reserved for future use" in PCI
spec, so changing them might have side effects.

No such issue for I/O or memory, as there is an implementation note in
PCI spec which explicitly allows writing 0xfffffffff there.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 08:59:40 -08:00
Allen Kay
df0e97c6f1 PCI: add xen dom0 checking before ACS initialization
This patch is predicated on Jeremy's patch in include/xen/xen.h.  It'll
prevent ACS init unless the platform has both an IOMMU and we're running
as dom0.

Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 08:47:26 -08:00
Allen Kay
ae21ee65e8 PCI: acs p2p upsteram forwarding enabling
Note: dom0 checking in v4 has been separated out into 2/2.

This patch enables P2P upstream forwarding in ACS capable PCIe switches.
It solves two potential problems in virtualization environment where a PCIe
device is assigned to a guest domain using a HW iommu such as VT-d:

1) Unintentional failure caused by guest physical address programmed
   into the device's DMA that happens to match the memory address range
   of other downstream ports in the same PCIe switch.  This causes the PCI
   transaction to go to the matching downstream port instead of go to the
   root complex to get translated by VT-d as it should be.

2) Malicious guest software intentionally attacks another downstream
   PCIe device by programming the DMA address into the assigned device
   that matches memory address range of the downstream PCIe port.

We are in process of implementing device filtering software in KVM/XEN
management software to allow device assignment of PCIe devices behind a PCIe
switch only if it has ACS capability and with the P2P upstream forwarding bits
enabled.  This patch is intended to work for both KVM and Xen environments.

Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Reviewed-by: Mathew Wilcox <willy@linux.intel.com>
Reviewed-by: Chris Wright <chris@sous-sol.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 08:47:25 -08:00
Bjorn Helgaas
a369c791e8 PCI: print resources consistently with %pRt
This uses %pRt to print additional resource information (type, size,
prefetchability, etc.) consistently.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-11-04 08:47:18 -08:00
Rafael J. Wysocki
4b77b0a2ba PCI: Clear saved_state after the state has been restored
Some PCI devices fail if their standard configuration registers are
restored twice in a row.  Prevent this from happening by making
pci_restore_state() clear the saved_state flag of the device right
after the device's standard configuration registers have been
populated with the previously saved values.

Simplify PCI PM callbacks by removing the direct clearing of
state_saved from them, as it shouldn't be necessary any more (except
in pci_pm_thaw(), where it has to be cleared, so that the values saved
during the "freeze" phase of hibernation are not used later by mistake).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-09-14 13:41:46 -07:00
Eric W. Biederman
28760489a3 PCI: pcie: Ensure hotplug ports have a minimum number of resources
In general a BIOS may goof or we may hotplug in a hotplug controller.
In either case the kernel needs to reserve resources for plugging
in more devices in the future instead of creating a minimal resource
assignment.

We already do this for cardbus bridges I am just adding a variant
for pcie bridges.

v2: Make testing for pcie hotplug bridges based on a flag.

    So far we only set the flag for pcie but a header_quirk
    could easily be added for the non-standard pci hotplug
    bridges.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-09-09 14:10:24 -07:00
Yinghai Lu
d0b8cbed64 PCI: print out pref if mmio is prefetchable
We already print it out for pci bridges, so also print it out for pci devices.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-09-09 13:29:27 -07:00
Alex Chiang
a7db504052 PCI: remove pcibios_scan_all_fns()
This was #define'd as 0 on all platforms, so let's get rid of it.

This change makes pci_scan_slot() slightly easier to read.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-09-09 13:29:18 -07:00
Kenji Kaneshige
9fc3925650 PCI: use pci_is_root_bus() in pci_read_bridge_bases()
Use pci_is_root_bus() in pci_read_bridge_bases() to check if the pci
bus is root, for code consistency.

Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-06-16 14:29:31 -07:00
Yinghai Lu
1f82de10d6 PCI/x86: don't assume prefetchable ranges are 64bit
We should not assign 64bit ranges to PCI devices that only take 32bit
prefetchable addresses.

Try to set IORESOURCE_MEM_64 in 64bit resource of pci_device/pci_bridge
and make the bus resource only have that bit set when all devices under
it support 64bit prefetchable memory.  Use that flag to allocate
resources from that range.

Reported-by: Yannick <yannick.roehlly@free.fr>
Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-06-11 12:04:06 -07:00
Yu Zhao
f79b1b146b PCI: use fixed-up device class when configuring device
The device class may be changed after the fixup, so re-read the class
value from pci_dev when configuring the device.  Otherwise some devices
such as JMicron SATA controller won't work.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-06-04 11:29:43 +01:00
Matthew Wilcox
0bb1be3e30 x86/PCI: Move set_pci_bus_resources_arch_default into arch/x86
Commit 30a18d6c3f introduced a new
function to set the PCI bus resources.  Unfortunately, neither the
author, nor the committers seemed to know that we already have somewhere
to do that -- pcibios_fixup_bus().  This patch moves the hook (used only
by the K8 code) into x86-specific code where it should have been in the
first place.

Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-22 13:57:36 -07:00
Alex Chiang
5446a6bdb5 PCI: annotate pci_rescan_bus as __ref, not __devinit
pci_rescan_bus was annotated as __devinit, which is wrong,
because it will never be part of device initialization.
Howevever, we can't simply drop the annotation, because then we
get section warnings about calling pci_scan_child_bus (which is
correctly marked as __devinit).

pci_rescan_bus will only get built when CONFIG_HOTPLUG is set,
meaning that __devinit is a nop, so we know that pci_scan_child_bus
has not been freed.

Annotate as __ref to silence modpost.

Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-04-06 11:26:07 -07:00
Yu Zhao
853346e435 PCI: fix conflict between SR-IOV and config space sizing
New pci_cfg_space_size() needs invalid pdev->class, put it in the
right place in the pci_setup_device().

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-26 15:50:18 -07:00
Alex Chiang
705b1aaa82 PCI: Introduce /sys/bus/pci/rescan
This interface allows the user to force a rescan of all PCI buses
in system, and rediscover devices that have been removed earlier.

pci_bus_attrs implementation from Trent Piepho.

Thanks to Vegard Nossum for discovering locking issues with the
sysfs interface.

Cc: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 14:57:58 -07:00
Alex Chiang
3ed4fd96b3 PCI: Introduce pci_rescan_bus()
This API is used by the PCI core to rescan a bus and rediscover
newly added devices.

Over time, it is expected that the various PCI hotplug drivers
will migrate to this interface and away from the old
pci_do_scan_bus() interface.

Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 14:57:44 -07:00
Alex Chiang
74710ded8e PCI: always scan child buses
While scanning bridges, we stop our scan if we encounter a bus
that we've seen before, to work around some buggy chipsets. This
is a good idea, but prevents us from fully scanning the PCI bus
at a future time (to find newly hot-added devices, for example).

Change the logic so that we skip _re-adding_ an existing bus
that we've seen before, but also allow the scan to descend to
all child buses.

Now that we're potentially scanning our child buses again, we
also need to be sure not to attempt re-initializing their BARs
so we avoid that.

This patch lays the groundwork to allow the user to issue a
rescan of the PCI bus at any time.

Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 14:57:21 -07:00
Trent Piepho
1b69dfc649 PCI: pci_scan_slot() returns newly found devices
pci_scan_slot() has been rewritten to be less complex and will now
return the number of *new* devices found.

Existing callers need not worry because they already assume that
they can't call pci_scan_slot() on an already-scanned slot.

Thus, there is no semantic change for existing callers: returning
newly found devices (this patch) is exactly equal to returning all
found devices (before this patch).

This patch adds some more groundwork to allow us to rescan the
PCI bus during runtime to discover newly added devices.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 14:57:05 -07:00
Trent Piepho
90bdb3117f PCI: don't scan existing devices
pci_scan_single_device is supposed to add newly discovered
devices to pci_bus->devices, but doesn't check to see if the
device has already been added. This can cause problems if we ever
want to use this interface to rescan the PCI bus.

If the device is already added, just return it.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 14:56:45 -07:00
Yu Zhao
480b93b783 PCI: centralize device setup code
Move the device setup stuff into pci_setup_device() which will be used
to setup the Virtual Function later.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:25 -07:00
Yu Zhao
a28724b0fb PCI: reserve bus range for SR-IOV device
Reserve the bus number range used by the Virtual Function when
pcibios_assign_all_busses() returns true.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:24 -07:00
Yu Zhao
d1b054da8f PCI: initialize and release SR-IOV capability
If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.

Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:22 -07:00
Yinghai Lu
dfadd9edff PCI/x86: detect host bridge config space size w/o using quirks
Many host bridges support a 4k config space, so check them directy
instead of using quirks to add them.

We only need to do this extra check for host bridges at this point,
because only host bridges are known to have extended address space
without also having a PCI-X/PCI-E caps.  Other devices with this
property could be done with quirks (if there are any).

As a bonus, we can remove the quirks for AMD host bridges with family
10h and 11h since they're not needed any more.

With this patch, we can get correct pci cfg size of new Intel CPUs/IOHs
with host bridges.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:17 -07:00
Geert Uytterhoeven
6a3b3e2680 PCI: Use kzalloc() in pci_create_bus()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:15 -07:00
Kenji Kaneshige
f92d4e29d7 PCI: fix wrong assumption in pci_read_bridge_bases
Current pci_read_bridge_bases() has an assumption that pci_bus->self
is NULL on the pci root bus (It checks pci_bus->self to see if the pci
bus is root bus). But is might not true on some platforms. We must
check pci_bus->parent instead.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 10:48:04 -07:00
Linus Torvalds
4e9b1c184c Merge branch 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  [IA64] fix typo in cpumask_of_pcibus()
  x86: fix x86_32 builds for summit and es7000 arch's
  cpumask: use work_on_cpu in acpi-cpufreq.c for read_measured_perf_ctrs
  cpumask: use work_on_cpu in acpi-cpufreq.c for drv_read and drv_write
  cpumask: use cpumask_var_t in acpi-cpufreq.c
  cpumask: use work_on_cpu in acpi/cstate.c
  cpumask: convert struct cpufreq_policy to cpumask_var_t
  cpumask: replace CPUMASK_ALLOC etc with cpumask_var_t
  x86: cleanup remaining cpumask_t ops in smpboot code
  cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
  cpumask: update local_cpus_show to use new cpumask API
  ia64: cpumask fix for is_affinity_mask_valid()
2009-01-10 06:12:18 -08:00
Jesse Barnes
eb9c39d031 PCI: set device wakeup capable flag if platform support is present
When PCI devices are initialized, we check whether they support PCI PM
caps and set the device can_wakeup flag if so.  However, some devices
may have platform provided wakeup events rather than PCI PME signals, so
we need to set can_wakeup in that case too.  Doing so should allow
wakeups from many more devices, especially on cost constrained systems.

Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Joseph Chan <JosephChan@via.com.tw>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:07 -08:00
Yu Zhao
3789fa8a2e PCI: allow pci_alloc_child_bus() to handle a NULL bridge
Allow pci_alloc_child_bus() to allocate buses without bridge devices.
Some SR-IOV devices can occupy more than one bus number, but there is no
explicit bridges because that have internal routing mechanism.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:03 -08:00
Yu Zhao
0b400c7ed4 PCI: export __pci_read_base()
Export __pci_read_base() so it can be used by whole PCI subsystem.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:02 -08:00
Yu Zhao
fde09c6d8f PCI: define PCI resource names in an 'enum'
This patch moves all definitions of the PCI resource names to an 'enum',
and also replaces some hard-coded resource variables with symbol
names. This change eases introduction of device specific resources.

Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:13:01 -08:00
Rafael J. Wysocki
63f4898ace PCI: handle PCI state saving with interrupts disabled
Since interrupts will soon be disabled at PCI resume time, we need to
pre-allocate memory to save/restore PCI config space (or use GFP_ATOMIC,
but this is safer).

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:40 -08:00
Kay Sievers
1a9271331a PCI: struct device - replace bus_id with dev_name(), dev_set_name()
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".

To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.

We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.

Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-01-07 11:12:23 -08:00
Mike Travis
588235bb53 cpumask: update pci_bus_show_cpuaffinity to use new cpumask API
Impact: use new cpumask API to reduce stack usage

Replace the local cpumask_t variable with a pointer to the
const cpumask that needs to be printed.

Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-01-04 15:39:26 +01:00
Rusty Russell
29c0177e6a cpumask: change cpumask_scnprintf, cpumask_parse_user, cpulist_parse, and cpulist_scnprintf to take pointers.
Impact: change calling convention of existing cpumask APIs

Most cpumask functions started with cpus_: these have been replaced by
cpumask_ ones which take struct cpumask pointers as expected.

These four functions don't have good replacement names; fortunately
they're rarely used, so we just change them over.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: paulus@samba.org
Cc: mingo@redhat.com
Cc: tony.luck@intel.com
Cc: ralf@linux-mips.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: cl@linux-foundation.org
Cc: srostedt@redhat.com
2008-12-13 21:20:25 +10:30
Zhao, Yu
a491913ff2 PCI: remove unused resource assignment in pci_read_bridge_bases()
This cleanup removes the resource assignment in pci_read_bridge_bases()
since it has taken care by pci_alloc_child_bus() when allocating the bus:

        /* Set up default resource pointers and names.. */
        for (i = 0; i < PCI_BRIDGE_RES_NUM; i++) {
                child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i];
                child->resource[i]->name = child->name;
        }

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-23 16:17:47 -07:00
Benjamin Herrenschmidt
a1c19894b7 PCI: Workaround invalid P2P bridge bus numbers
Some firmware fail to properly configure P2P bridges, leaving them
with invalid bus numbers. In some cases, this happens on some embedded
4xx boards as the result of the kernel allocating different bus space
than the firmware does to host bridges while not setting
pcibios_assign_all_busses() for various reasons. In other cases, it can
just be bogus firmware.

This adds some sanity checking to the PCI probing code. If a bridge is
found whose primary bus number doesn't match the bus it's sitting on,
or whose secondary bus number not strictly above it's primary bus
number, then the bridge bus numbers are deconfigured in the first pass
of pci_scan_bridge() to be re-assigned in the second pass.

Tested-by: "Ayman El-Khashab" <AymanE@tanisys.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-22 16:42:44 -07:00
Benjamin Herrenschmidt
f19aeb1f36 PCI: Add ability to mmap legacy_io on some platforms
This adds the ability to mmap legacy IO space to the legacy_io files
in sysfs on platforms that support it. This will allow to clean up
X to use this instead of /dev/mem for legacy IO accesses such as
those performed by Int10.

While at it I moved pci_create/remove_legacy_files() to pci-sysfs.c
where I think they belong, thus making more things statis in there
and cleaned up some spurrious prototypes in the ia64 pci.h file

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 11:01:46 -07:00
Vincent Legoll
f393d9b130 PCI: probing debug message uniformization
This patch uniformizes PCI probing debug boot messages with dev_printk()
intead of manual printk()

It changes adress range output from [%llx, %llx] to [%#llx-%#llx], like
in pci_request_region().

For example, it goes from the mixed-style:

PCI: 0000:00:1b.0 reg 10 64bit mmio: [f4280000, f4283fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold

to uniform:

pci 0000:00:1b.0: reg 10 64bit mmio: [0xf4280000-0xf4283fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold

This patch has been runtime tested, boot log messages diffed, everything
looks OK.

Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 11:01:45 -07:00
Yu Zhao
58c3a727cb PCI: support PCIe ARI capability
This patch adds support for PCI Express Alternative Routing-ID
Interpretation (ARI) capability.

The ARI capability extends the Function Number field of the PCI Express
Endpoint by reusing the Device Number which is otherwise hardwired to 0.
With ARI, an Endpoint can have up to 256 functions.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:54:32 -07:00
Zhao, Yu
201de56eb2 PCI: centralize the capabilities code in probe.c
This patch centralizes the initialization and release functions of
various PCI capabilities in probe.c, which makes the introduction
of new capability support functions cleaner in the future.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:54:31 -07:00
Peter Chubb
e354597cce PCI: fix 64-vbit prefetchable memory resource BARs
Since patch 6ac665c63d my infiniband
controller hasn't worked.  This is because it has 64-bit prefetchable
memory, which was mistakenly being  taken to be 32-bit memory.  The
resource flags in this case are PCI_BASE_ADDRESS_MEM_TYPE_64 |
PCI_BASE_ADDRESS_MEM_PREFETCH.

This patch checks only for the PCI_BASE_ADDRESS_MEM_TYPE_64 bit; thus
whether the region is prefetchable or not is ignored.  This fixes my
Infiniband.

Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:54:30 -07:00
Zhao, Yu
557848c3c0 PCI: replace cfg space size (256/4096) by macros.
This is a cleanup that changes all PCI configuration space size
representations to the macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE). And the macros are also moved from
drivers/pci/probe.c to drivers/pci/pci.h.

Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:54:29 -07:00
Alex Chiang
cef354db0d PCI: connect struct pci_dev to struct pci_slot
The introduction of struct pci_slot (f46753c5e3)
added a struct pci_slot pointer to struct pci_dev, but we forgot to
associate the two.

Connect the two structs together; the interesting portions of the object
lifetimes are:

	- when a new pci_slot is created, connect it to the appropriate
	  pci_dev's. A single pci_slot may be associated with multiple
	  pci_dev's, e.g. any multi-function PCI device.

	- when a pci_slot is released, look for all the pci_dev's it was
	  associated with, and set their pci_slot pointers to NULL

	- when a pci_dev is created, look for slots to associate with.

Note -- when a pci_dev is released, we don't need to do any bookkeeping,
since pci_slot's do not have pointers to pci_dev's.

Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:53:52 -07:00
Bjorn Helgaas
34a2e15e95 PCI: follow lspci device/vendor style
Use "[%04x:%04x]" for PCI vendor/device IDs to follow the format
used by lspci(8).

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-10-20 10:53:43 -07:00
Benjamin Herrenschmidt
096e6f673d pci: Use new %pR to print resource ranges
This converts things in drivers/pci to use %pR to printout the
content of a struct resource instead of hand-casted %llx or
other variants.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 09:12:32 -07:00
Greg Kroah-Hartman
99178b036c Driver core: add bus_sort_breadthfirst() function
The PCI core wants to reorder the devices in the bus list.  So move this
functionality out of the pci core and into the driver core so that
anyone else can also do this if needed.  This also lets us change how
struct device is attached to drivers in the future without messing with
the PCI core.

Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-16 09:24:52 -07:00
Yinghai Lu
395a125c62 PCI: re-add debug prints for unmodified BARs
Print out for device BAR values before the kernel tries to update them.
Also make related output use KERN_DEBUG.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-09-12 16:34:46 -07:00
Johann Felix Soden
4ca8a7726f PCI: Fix printk warnings in probe.c
The cleaned up resource code in probe.c introduced some warnings:
drivers/pci/probe.c: In function 'pci_read_bridge_bases':
drivers/pci/probe.c:386: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pci/probe.c:386: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:398: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pci/probe.c:398: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:434: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:434: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'resource_size_t'

So fix them up.

Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-09-09 11:43:32 -07:00
Jesse Barnes
ce6754235b Merge branch 'pci-for-jesse' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip into x86-merge
Conflicts:

	drivers/pci/probe.c
2008-08-18 09:54:13 -07:00
Simon Horman
a844158a64 PCI: check the return value of device_create_bin_file() in pci_create_bus()
Check the return value of device_create_bin_file in pci_create_bus and
unwind if necessary. Don't propagate error to caller, as failure to create
these files shouldn't prevent PCI from being initialised. Instead, just
log a warning.

Cc: Sven Wegener <sven.wegener@stealer.net>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-08-07 09:49:07 -07:00
Shaohua Li
149e16372a PCI: disable ASPM on pre-1.1 PCIe devices
Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it
correctly.

Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-28 14:56:57 -07:00
Matthew Wilcox
cc5499c3a6 PCI: handle 64-bit resources better on 32-bit machines
If the kernel is configured to support 64-bit resources on a 32-bit
machine, we can support 64-bit BARs properly.  Just change the condition
to check sizeof(resource_size_t) instead of BITS_PER_LONG.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-07-28 14:29:04 -07:00