commit 3c97af99a5 (ipip: percpu stats accounting) forgot the fallback
tunnel case (tunl0), and can crash pretty fast.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As tunnel devices are going to be lockless, we need to make sure a
misconfigured machine wont enter an infinite loop.
Add a percpu variable, and limit to three the number of stacked xmits.
Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AnyIP is the capability to receive packets and establish incoming
connections on IPs we have not explicitly configured on the machine.
An example use case is to configure a machine to accept all incoming
traffic on eth0, and leave the policy of whether traffic for a given IP
should be delivered to the machine up to the load balancer.
Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a host to be configured to respond to any address in
a specified range as if it were local, without actually needing to
configure the address on an interface. This is done through routing
table configuration. For instance, to configure a host to respond
to any address in 10.1/16 received on eth0 as a local address we can do:
ip rule add from all iif eth0 lookup 200
ip route add local 10.1/16 dev lo proto kernel scope host src 127.0.0.1 table 200
This host is now reachable by any 10.1/16 address (route lookup on
input for packets received on eth0 can find the route). On output, the
rule will not be matched so that this host can still send packets to
10.1/16 (not sent on loopback). Presumably, external routing can be
configured to make sense out of this.
To make this work, we needed to modify the logic in finding the
interface which is assigned a given source address for output
(dev_ip_find). We perform a normal fib_lookup instead of just a
lookup on the local table, and in the lookup we ignore the input
interface for matching.
This patch is useful to implement IP-anycast for subnets of virtual
addresses.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This covers RX if necessary, as well as TX.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RPS, we create a kobject for each RX queue based on the number of
queues passed to alloc_netdev_mq(). However, drivers generally do not
determine the numbers of hardware queues to use until much later, so
this usually represents the maximum number the driver may use and not
the actual number in use.
For TX queues, drivers can update the actual number using
netif_set_real_num_tx_queues(). Add a corresponding function for RX
queues, netif_set_real_num_rx_queues().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_attach_filter() and sk_detach_filter() are run with socket locked.
Use the appropriate rcu_dereference_protected() instead of blocking BH,
and rcu_dereference_bh().
There is no point adding BH prevention and memory barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems we dont use appropriate refcount increment in an
rcu_read_lock() protected section.
fib_rule_get() might increment a null refcount and bad things could
happen.
While fib_nl_delrule() respects an rcu grace period before calling
fib_rule_put(), fib_rules_cleanup_ops() calls fib_rule_put() without a
grace period.
Note : after this patch, we might avoid the synchronize_rcu() call done
in fib_nl_delrule()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.
Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.
This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.
Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.
This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le lundi 27 septembre 2010 à 14:29 +0100, Ben Hutchings a écrit :
> > diff --git a/net/ipv4/ip_gre.c b/net/ipv4/ip_gre.c
> > index 5d6ddcb..de39b22 100644
> > --- a/net/ipv4/ip_gre.c
> > +++ b/net/ipv4/ip_gre.c
> [...]
> > @@ -377,7 +405,7 @@ static struct ip_tunnel *ipgre_tunnel_locate(struct net *net,
> > if (parms->name[0])
> > strlcpy(name, parms->name, IFNAMSIZ);
> > else
> > - sprintf(name, "gre%%d");
> > + strcpy(name, "gre%d");
> >
> > dev = alloc_netdev(sizeof(*t), name, ipgre_tunnel_setup);
> > if (!dev)
> [...]
>
> This is a valid fix, but doesn't belong in this patch!
>
Sorry ? It was not a fix, but at most a cleanup ;)
Anyway I forgot the gretap case...
[PATCH 2/4 v2] ip_gre: percpu stats accounting
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets.
Other seldom used fields are kept in netdev->stats structure, possibly
unsafe.
This is a preliminary work to support lockless transmit path, and
correct RX stats, that are already unsafe.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phonet stack assumes the presence of Pipe Controller, either in Modem or
on Application Processing Engine user-space for the Pipe data.
Nokia Slim Modems like WG2.5 used in ST-Ericsson U8500 platform do not
implement Pipe controller in them.
This patch adds Pipe Controller implemenation to Phonet stack to support
Pipe data over Phonet stack for Nokia Slim Modems.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a missing exit path in the ipv6 module init routines. In
addrconf_init we call ipv6_addr_label_init which calls register_pernet_subsys
for the ipv6_addr_label_ops structure. But if module loading fails, or if the
ipv6 module is removed, there is no corresponding unregister_pernet_subsys call,
which leaves a now-bogus address on the pernet_list, leading to oopses in
subsequent registrations. This patch cleans up both the failed load path and
the unload path. Tested by myself with good results.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
include/net/addrconf.h | 1 +
net/ipv6/addrconf.c | 11 ++++++++---
net/ipv6/addrlabel.c | 5 +++++
3 files changed, 14 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
__in_dev_get_rtnl(dev_out) is called while RTNL is not held, thus
triggers a lockdep fault.
At this point, we only perform a raw test of dev_out->ip_ptr being NULL,
we dont need to make sure ip_ptr cant changed right after.
We can use rcu_dereference_raw() for this.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having two places were we allocate dev->_rx, introduce
netif_alloc_rx_queues() helper and call it only from
register_netdevice(), not from alloc_netdev_mq()
Goal is to let drivers change dev->num_rx_queues after allocating netdev
and before registering it.
This also removes a lot of ifdefs in net/core/dev.c
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
You can't call atomic_notifier_chain_unregister() while in atomic context.
Fix, call un/register_atmdevice_notifier in module __init and __exit.
Bug report:
http://comments.gmane.org/gmane.linux.network/172603
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically allows vlans to get NETIF_F_HIGHDMA if underlying device
supports it.
On 32bit arches (and more precisely if CONFIG_HIGHMEM is enabled), it
can help to reduce cost of illegal_highdma() and __skb_linearize()
calls.
Tested on tg3 , bnx2, bonding, this worked very well.
This is a generalization of a patch provided by Yi Zou & Jeff Kirsher.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)
This (C) case conflicts with (A) :
CPU1 [A] CPU2 [C]
read_lock(callback_lock)
<BH> spin_lock_bh(slock)
<wait to spin_lock(slock)>
<wait to write_lock_bh(callback_lock)>
We have one problematic (C) use case in inet_csk_listen_stop() :
local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While investigating a bit, I found ip_fragment() slow path was taken
because ip_append_data() provides following layout for a send(MTU +
N*(MTU - 20)) syscall :
- one skb with 1500 (mtu) bytes
- N fragments of 1480 (mtu-20) bytes (before adding IP header)
last fragment gets 17 bytes of trail data because of following bit:
if (datalen == length + fraggap)
alloclen += rt->dst.trailer_len;
Then esp4 adds 16 bytes of data (while trailer_len is 17... hmm...
another bug ?)
In ip_fragment(), we notice last fragment is too big (1496 + 20) > mtu,
so we take slow path, building another skb chain.
In order to avoid taking slow path, we should correct ip_append_data()
to make sure last fragment has real trail space, under mtu...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise ECT(1) bit will get interpreted as RTO_ONLINK
and routing will fail with XfrmOutBundleGenError.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The x25_datagram_poll didn't add anything, removed it.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we need to check proper socket type within ipv4_conntrack_defrag
function before referencing the nodefrag flag.
For example the tun driver receive path produces skbs with
AF_UNSPEC socket type, and so current code is causing unwanted
fragmented packets going out.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checksum calculation in nf_nat_snmp_basic.
Based on patches by Clark Wang <wtweeker@163.com> and
Stephen Hemminger <shemminger@vyatta.com>.
https://bugzilla.kernel.org/show_bug.cgi?id=17622
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as rcu_read_unlock() is called, there is no guarantee current
thread can safely derefence t pointer, rcu protected.
Fix is to copy t->alloc_size in a temporary variable.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_me_harder can't create the route cache when the outdev is the same
with the indev for the skbs whichout a valid protocol set.
__mkroute_input functions has this check:
1998 if (skb->protocol != htons(ETH_P_IP)) {
1999 /* Not IP (i.e. ARP). Do not create route, if it is
2000 * invalid for proxy arp. DNAT routes are always valid.
2001 *
2002 * Proxy arp feature have been extended to allow, ARP
2003 * replies back to the same interface, to support
2004 * Private VLAN switch technologies. See arp.c.
2005 */
2006 if (out_dev == in_dev &&
2007 IN_DEV_PROXY_ARP_PVLAN(in_dev) == 0) {
2008 err = -EINVAL;
2009 goto cleanup;
2010 }
2011 }
This patch gives the new skb a valid protocol to bypass this check. In order
to make ipt_REJECT work with bridges, you also need to enable ip_forward.
This patch also fixes a regression. When we used skb_copy_expand(), we
didn't have this issue stated above, as the protocol was properly set.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I initially noticed this because of the compiler warning below, but it
does seem to be a valid concern in the case where ct_sip_get_header()
returns 0 in the first iteration of the while loop.
net/netfilter/nf_conntrack_sip.c: In function 'sip_help_tcp':
net/netfilter/nf_conntrack_sip.c:1379: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Simon Horman <horms@verge.net.au>
[Patrick: changed NF_DROP to NF_ACCEPT]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
transparent field of a socket is either inet_twsk(sk)->tw_transparent
for timewait sockets, or inet_sk(sk)->transparent for other sockets
(TCP/UDP).
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAIF sockets should use socket's default send and receive buffers sizes.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that receive function pointer is not null before calling it.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_debug for flow control printouts, and refine an error printout.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove debugging quirk redefining pr_debug to pr_warning.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/ethtool.c: In function 'ethtool_get_regs':
net/core/ethtool.c:818:2: error: implicit declaration of function 'vmalloc'
net/core/ethtool.c:818:9: warning: assignment makes pointer from integer without a cast
net/core/ethtool.c:833:2: error: implicit declaration of function 'vfree'
Signed-off-by: David S. Miller <davem@davemloft.net>
Special care should be taken when slow path is hit in ip_fragment() :
When walking through frags, we transfert truesize ownership from skb to
frags. Then if we hit a slow_path condition, we must undo this or risk
uncharging frags->truesize twice, and in the end, having negative socket
sk_wmem_alloc counter, or even freeing socket sooner than expected.
Many thanks to Nick Bowler, who provided a very clean bug report and
test program.
Thanks to Jarek for reviewing my first patch and providing a V2
While Nick bisection pointed to commit 2b85a34e91 (net: No more
expensive sock_hold()/sock_put() on each tx), underlying bug is older
(2.6.12-rc5)
A side effect is to extend work done in commit b2722b1c3a
(ip_fragment: also adjust skb->truesize for packets not owned by a
socket) to ipv6 as well.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some NICs have huge register files which exceed the maximum heap
allocation size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The `options_received' struct is redundant, since it re-duplicates the existing
`p' and `x_recv' fields. This patch removes the sub-struct and migrates the
format conversion operations to ccid3_hc_tx_parse_options().
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This adds a function to take care of the following, separate cases occurring in
the computation of the Loss Rate p:
* 1/(2^32-1) is mapped into 0% as per RFC 4342, 8.5;
* 1/0 is mapped into 100%, the maximum;
* to avoid that p = 1/x is rounded down to 0 when x is very large, since this
means accidentally re-entering slow-start indicated by p == 0, the minimum
resolution value of p is now returned instead;
* a bug in ccid3_hc_rx_getsockopt is fixed: 1/0 was mapped into ~0U.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch is thanks to an investigation by Leandro Sales de Melo and his
colleagues. They worked out two state diagrams which highlight the fact that
the xxx_TERM states in CCID-3/4 are in fact not necessary.
And this can be confirmed by in turn looking at the code: the xxx_TERM states
are only ever set in ccid3_hc_{rx,tx}_exit(): when CCID-3 sets the state
to xxx_TERM, it is at a time where no more processing should be going on,
hence it is not necessary to introduce a dedicated exit state - this is already
implied by unloading the CCID.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The constants DCCPO_{MIN,MAX}_CCID_SPECIFIC are nowhere used in the code, but
instead for the CCID-specific options numbers are used.
This patch unifies the use of CCID-specific option numbers, by adding symbolic
names reflecting the definitions in RFC 4340, 10.3.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This
1. adds packet type information to ccid_hc_{rx,tx}_parse_options(). This is
necessary, since table 3 in RFC 4340, 5.8 leaves it to the CCIDs to state
which options may (not) appear on what packet type.
2. adds such a check for CCID-3's {Loss Event, Receive} Rate as specified in
RFC 4340 8.3 ("Receive Rate options MUST NOT be sent on DCCP-Data packets")
and 8.5 ("Loss Event Rate options MUST NOT be sent on DCCP-Data packets").
3. removes an unused argument `idx' from ccid_hc_{rx,tx}_parse_options(). This
is also no longer necessary, since the CCID-specific option-parsing routines
are passed every single parameter of the type-length-value option encoding.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
If a RST comes in immediately after checking sk->sk_err, tcp_poll will
return POLLIN but not POLLOUT. Fix this by checking sk->sk_err at the end
of tcp_poll. Additionally, ensure the correct order of operations on SMP
machines with memory barriers.
Signed-off-by: Tom Marshall <tdm.code@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
