Add nodes for the SPICC controller on GX common dtsi, GXBB and
GXL dtsi files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add HDMI and CVBS nodes for the Amlogic P212 reference board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add HDMI and CVBS nodes for the Wetek Play2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch to use the new compatible for the SCPI sensors so that the
sensor readings are reported using the correct scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the SPICC Controller pins nodes for Amlogic GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the SPICC Controller pins nodes for Amlogic GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs adds
the Link and Activity LEDs signals pins nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO and EE domain CEC pins nodes for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The pull-enable register base was wrongly copied from the meson8b pinctrl node,
but was not used yet.
Fixes: c328666d58 ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The pull-enable register base was wrongly copied from the GXBB pinctrl node,
but was not used yet.
Fixes: fb0fe92294 ("ARM64: dts: meson-gxl: Add pinctrl nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The gpio-range was badly added on the GXL dtsi, the AO pin count is 10
instead of 14.
Fixes: 84412e4e85 ("ARM64: dts: meson-gxl: Add gpio-ranges properties")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The FriendlyARM NanoPi K2 is a single-board computer.
Cc: techsupport@friendlyarm.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The R-Box Pro is a TV box derived from Amlogic q200 reference design.
It uses an AP6255 Wifi module. It features an LED tube that lights a
surrounding stripe and the top logo in blue or red or pink'ish - blue
is on by default, and red (i.e., pink) is configured as panic indicator.
This device is available in at least two models, with 2 GB vs. 3 GB RAM
as well as varying eMMC size. The intent is to handle this with a single
.dts that gets the actual RAM size from U-Boot.
Cc: ada@kingnoval.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Makes the override safer.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Product pictures show no DB9 connector, so this seems copy&paste.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
bcrmf -> brcmf -> wifi
Fixes: e15d2774b8 ("ARM64: dts: meson-gxl: add support for the Khadas VIM board")
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
bcrmf -> brcmf -> wifi
Fixes: bb51b5350d ("ARM64: dts: Add support for Meson GXM")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Sort the .dtb files alphabetically to make clear where to add new ones.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This branch introduces a generic TEE framework in the kernel, to handle
trusted environemtns (security coprocessor or software implementations
such as OP-TEE/TrustZone). I'm sending it separately from the other
arm-soc driver changes to give it a little more visibility, once
the subsystem is merged, we will likely keep this in the arm₋soc
drivers branch or have the maintainers submit pull requests directly,
depending on the patch volume.
I have reviewed earlier versions in the past, and have reviewed
the latest version in person during Linaro Connect BUD17.
Here is my overall assessment of the subsystem:
* There is clearly demand for this, both for the generic
infrastructure and the specific OP-TEE implementation.
* The code has gone through a large number of reviews,
and the review comments have all been addressed, but
the reviews were not coming up with serious issues any more
and nobody volunteered to vouch for the quality.
* The user space ioctl interface is sufficient to work with the
OP-TEE driver, and it should in principle work with other
TEE implementations that follow the GlobalPlatform[1] standards,
but it might need to be extended in minor ways depending on
specific requirements of future TEE implementations
* The main downside of the API to me is how the user space
is tied to the TEE implementation in hardware or firmware,
but uses a generic way to communicate with it. This seems
to be an inherent problem with what it is trying to do,
and I could not come up with any better solution than what
is implemented here.
For a detailed history of the patch series, see
https://lkml.org/lkml/2017/3/10/1277
Conflicts: needs a fixup after the drm tree was merged, see
https://patchwork.kernel.org/patch/9691679/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VzpB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tee' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull TEE driver infrastructure and OP-TEE drivers from Arnd Bergmann:
"This introduces a generic TEE framework in the kernel, to handle
trusted environemtns (security coprocessor or software implementations
such as OP-TEE/TrustZone). I'm sending it separately from the other
arm-soc driver changes to give it a little more visibility, once the
subsystem is merged, we will likely keep this in the arm₋soc drivers
branch or have the maintainers submit pull requests directly,
depending on the patch volume.
I have reviewed earlier versions in the past, and have reviewed the
latest version in person during Linaro Connect BUD17.
Here is my overall assessment of the subsystem:
- There is clearly demand for this, both for the generic
infrastructure and the specific OP-TEE implementation.
- The code has gone through a large number of reviews, and the review
comments have all been addressed, but the reviews were not coming
up with serious issues any more and nobody volunteered to vouch for
the quality.
- The user space ioctl interface is sufficient to work with the
OP-TEE driver, and it should in principle work with other TEE
implementations that follow the GlobalPlatform[1] standards, but it
might need to be extended in minor ways depending on specific
requirements of future TEE implementations
- The main downside of the API to me is how the user space is tied to
the TEE implementation in hardware or firmware, but uses a generic
way to communicate with it. This seems to be an inherent problem
with what it is trying to do, and I could not come up with any
better solution than what is implemented here.
For a detailed history of the patch series, see
https://lkml.org/lkml/2017/3/10/1277"
* tag 'armsoc-tee' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dt: hikey: Add optee node
Documentation: tee subsystem and op-tee driver
tee: add OP-TEE driver
tee: generic TEE subsystem
dt/bindings: add bindings for optee
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved over
from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288 SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using arm/
and arm64/ as include prefixes. This will avoid other local hacks such as
per-file links between the two arch trees (this broke for external mirroring
of DT contents). Now they can just provide their own appropriate dt-include
hierarcy per platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6w6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to the Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why it's
coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a common
way, which will help prevent any "badly-formed" devices from causing
problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
BspgO7ZmGb+9Fpf6YvNz
=nwAu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why
it's coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a
common way, which will help prevent any "badly-formed" devices from
causing problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
staging: typec: Fairchild FUSB302 Type-c chip driver
staging: typec: Type-C Port Controller Interface driver (tcpci)
staging: typec: USB Type-C Port Manager (tcpm)
usb: host: xhci: remove #ifdef around PM functions
usb: musb: don't mark of_dev_auxdata as initdata
usb: misc: legousbtower: Fix buffers on stack
USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
usb: Make sure usb/phy/of gets built-in
USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
usb: host: xhci: print correct command ring address
usb: host: xhci: delete sp_dma_buffers for scratchpad
usb: host: xhci: using correct specification chapter reference for DCBAAP
xhci: switch to pci_alloc_irq_vectors
usb: host: xhci-plat: set resume_quirk() for R-Car controllers
usb: host: xhci-plat: add resume_quirk()
usb: host: xhci-plat: enable clk in resume timing
usb: host: plat: Enable xHCI plat runtime PM
USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
USB: serial: constify static arrays
usb: fix some references for /proc/bus/usb
...
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon SOCs and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=p+Hb
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Continue to re-factor code to prepare for eMMC CMDQ and blkmq support
- Introduce queue semantics to prepare for eMMC CMDQ and blkmq support
- Add helper functions to manage temporary enable/disable of eMMC CMDQ
- Improve wait-busy detection for SDIO
MMC host:
- cavium: Add driver to support Cavium controllers
- cavium: Extend Cavium driver to support Octeon and ThunderX SOCs
- bcm2835: Add new driver for Broadcom BCM2835 controller
- sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller
- sdhci-tegra: Add support for the Tegra186 variant
- sdhci-of-esdhc: Support for UHS-I SD cards
- sdhci-of-esdhc: Support for eMMC HS200 cards
- sdhci-cadence: Add eMMC HS400 enhanced strobe support
- sdhci-esdhc-imx: Reset tuning circuit when needed
- sdhci-pci: Modernize and clean-up some PM related code
- sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices
- sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers
- sdhci: Re-factoring and modernizations
- sdhci: Optimize delay loops
- sdhci: Improve register dump print format
- sdhci: Add support for the Command Queue Engine
- meson-gx: Various improvements and clean-ups
- meson-gx: Add support for CMD23
- meson-gx: Basic tuning support to avoid CRC errors
- s3cmci: Enable probing via DT
- mediatek: Improve tuning support for eMMC HS200 and HS400 mode
- tmio: Improve DMA support
- tmio: Use correct response for CMD12
- dw_mmc: Minor improvements and clean-ups"
* tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (148 commits)
mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a
mmc: sdhci-of-esdhc: poll ESDHC_CLOCK_STABLE bit with udelay
mmc: sdhci-xenon: Fix default value of LOGIC_TIMING_ADJUST for eMMC5.0 PHY
mmc: sdhci-xenon: Fix the work flow in xenon_remove().
MIPS: Octeon: cavium_octeon_defconfig: Enable Octeon MMC
mmc: sdhci-xenon: Remove redundant dev_err call in get_dt_pad_ctrl_data()
mmc: cavium: Use module_pci_driver to simplify the code
mmc: cavium: Add MMC support for Octeon SOCs.
mmc: cavium: Fix detection of block or byte addressing.
mmc: core: Export API to allow hosts to get the card address
mmc: sdio: Fix sdio wait busy implement limitation
mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card
clk: apn806: fix spelling mistake: "mising" -> "missing"
mmc: sdhci-of-esdhc: add delay between tuning cycles
mmc: sdhci: Control the delay between tuning commands
mmc: sdhci-of-esdhc: add tuning support
mmc: sdhci-of-esdhc: add support for signal voltage switch
mmc: sdhci-of-esdhc: add peripheral clock support
mmc: sdhci-pci: Allow for 3 bytes from Intel DSM
mmc: cavium: Fix a shift wrapping bug
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
and sp9860g dts is for the board level.
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=NymV
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Fix DTC warnings in Exynos ARMv7 Device Tree sources." from Krzysztof Kozłowski:
* tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use - instead of @ for DT OPP entries
- Fix DTC warnings in Exynos ARM64 Device Tree sources.
- Add panel node to TM2E board.
-----BEGIN PGP SIGNATURE-----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=JgAW
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Second update of Samsung DeviceTree ARM64 for v4.12" from Krzysztof Kozłowski:
- Fix DTC warnings in Exynos ARM64 Device Tree sources.
- Add panel node to TM2E board.
* tag 'samsung-dt64-4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
1. Couple of fixes to remove device tree warnings introduced with
recently added checks in DTC
2. Add information about L1 and L2 caches to Juno device trees as
CCSIDR-based cacheinfo probing is now removed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5Rho
-----END PGP SIGNATURE-----
Merge tag 'juno-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt64
Pull "ARMv8 Juno DT fixes for v4.12" from Sudeep Holla:
1. Couple of fixes to remove device tree warnings introduced with
recently added checks in DTC
2. Add information about L1 and L2 caches to Juno device trees as
CCSIDR-based cacheinfo probing is now removed
* tag 'juno-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: dts: juno: fix PCI bus dtc warnings
Add fixed clock of 400MHz to system controller driver. This clock is
used as SD/eMMC clock source.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Omri Itach <omrii@marvell.com>
Reviewed-by: Hanna Hawa <hannah@marvell.com>
[fixed up conflicts, added error handling --rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the panel device tree node for s6e3hf2 display
controller to TM2e dts.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
- crypto engine description for the Armada 7k/8k SoCs and the boards
using it
- SDHCI description for the Armada 37xx and 7k/8k SoCs and the boards
using it
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWO+ljCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71Q9dAJ4i+PBERM8X
wh0AI0kekOBF33L4YQCcDr5wYXQdCYgwnTBVYadOHvce61A=
=zSnq
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.12-2' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.12 (part 2)
- crypto engine description for the Armada 7k/8k SoCs and the boards
using it
- SDHCI description for the Armada 37xx and 7k/8k SoCs and the boards
using it
* tag 'mvebu-dt64-4.12-2' of git://git.infradead.org/linux-mvebu:
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
Signed-off-by: Olof Johansson <olof@lixom.net>
