USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset. In that case, the warm reset change bit
will be set, and the link state change bit may also be set. Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs. If these bits are not cleared, we may lose port change events
from the roothub.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
'new_interfaces' should be freed to avoid memory leak.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old parameter "port" is useless for phy notify, as one usb
phy is only for one usb port. New parameter "speed" stands for
the device's speed which is on the port, this "speed" parameter
is needed at some platforms which will do some phy operations
according to device's speed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At commit 925aa46ba9, Richard Zhao
<richard.zhao@freescale.com> adds the phy notification callback
when port change occurs. In fact, this phy notification should
be added according to below rules:
1. Only set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during high speed host mode.
2. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during the reset and speed negotiation period.
3. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during host suspend/resume sequence.
Please refer: i.mx23RM(page: 413) for below rules.
http://www.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
Freescale i.MX SoC, i.mx23, i.mx28 and i.mx6(i.mx6SL does not
need to follow the 3rd rule) need to follow above rules.
Current code set connect notification (HW_USBPHY_CTRL.ENHOSTDISCONDETECT)
at hub_port_connect_change, it conflicts with above the 2th rule.
The correct notification setting method should be:
1. Set connect notify after the second bus reset.
2. Set disconnect notify after disconnection.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like I've run into some inconsistency in the USB stack behavior.
The USB stack maintains, among others, two states for the attach
USB device: authorized and owned. Authorization state is accessible to
the user space code through correspondent sysfs files, the ownership
can be set by claiming the hub's port with ioctl call. Both state may
be set before the device is attached, by access the hub settings. When
the new device is attached, both authorization and ownership prevent
the kernel USB stack from setting the newly attached device
configuration, but when the device is authorized, the ownership state
is ignored. It looks like ignoring the ownership state on
authorization make the stack behavior inconsistent; it also prevents
the user space code from completely overriding configuration
selection, important for implementing workarounds for bugs in the
device configuration selection.
The following patch makes the stack behavior more consistent, by
moving ownership test into usb_choose_configuration - the later
function is used both by generic_probe and usb_authorize_device
Signed-off-by: Joseph Hindin <hindin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 73d4066055.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1633) changes slightly the way usbcore handled
submissions of URBs that are already active. It will now return
-EBUSY rather than -EINVAL, and it will call WARN_ONCE to draw
people's attention to the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller. The controller needs to
be told to disable the endpoints that have been enabled for the new
config. The existing code does this, but before storing the
information about which endpoints were enabled! As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.
The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config. If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble. The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1621) removes the limit on the number of loops allowed
in hub_tt_work(). The value is arbitrary, and it's silly to have a
limit in the first place -- anything beyond the limit would not get
handled.
Besides, it's most unlikely that we'll ever need to clear more than a
couple of TT buffers at any time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
drivers/usb/misc/ezusb.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets hub device's default autosuspend delay as 0 to
speedup bus suspend, see comments in code for details.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub status endpoint has a long 'bInterval', which is 255ms
for FS/LS device and 256ms for HS device according to USB 2.0 spec,
so the device connection change may be reported later more than 255ms
via status pipe.
The connection change in hub may have been happened already on the
downstream ports, but no status URB completes when it is killed
in hub_suspend(auto), so the connection change may be missed by some
buggy hub devices, which won't generate remote wakeup signal after
their remote wakeup is enabled and they are put into suspend state.
The problem can be observed at least on the below Genesys Logic, Inc.
hub devices:
0x05e3,0x0606
0x05e3,0x0608
In theory, there is no way to fix the problem completely, but we
can make it less likely to occur by this patch.
This patch introduces one quirk of HUB_QUIRK_CHECK_PORTS_AUTOSUSPEND
to check ports' change during hub_suspend(auto) for the buggy
devices. If ports' change is found, terminate the auto suspend and
return to working state.
So for the buggy hubs, if the connection change happend before
the ports' check, it can be handled correctly. If it happens between
the ports' check and enabling remote wakeup/entering suspend, it
will be missed. Considered the interval is quite short, it is very
less likely to happen during the window.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1620) speeds up USB root-hub resumes in the common case
where every enabled port has its suspend feature set (which currently
will be true for every runtime resume of the root hub). If all the
enabled ports are suspended then resuming the root hub won't resume
any of the downstream devices. In this case there's no need for a
Resume Recovery delay, because that delay is meant to give devices a
chance to get ready for active use.
To keep track of the port suspend features, the patch adds a
"port_is_suspended" flag to struct usb_device. This has to be tracked
separately from the device's state; it's entirely possible for a USB-2
device to be suspended while the suspend feature on its parent port is
clear. The reason is that devices will go into suspend whenever their
parent hub does.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1619) improves the interface to the "hub_for_each_child"
macro. The name clearly suggests that the macro iterates over child
devices; it does not suggest that the loop will also iterate over
unnconnected ports.
The patch changes the macro so that it will skip over unconnected
ports and iterate only the actual child devices. The two existing
call sites are updated to avoid testing for a NULL child pointer,
which is now unnecessary.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We defined bus_to_hdc for that, use it.
Signed-off-by: Yuanhan Liu <yliu.null@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_work_sync and flush_work are now the same and flush_work_sync
has been deprecated. This fixes the following warning:
drivers/usb/core/hub.c: In function hub_quiesce:
drivers/usb/core/hub.c:1216:3: warning: flush_work_sync is deprecated (declared at include/linux/workqueue.h:448) [-Wdeprecated-declarations]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1611) updates the USB documentation and kerneldoc to
give a more precise meaning for the URB_ISO_ASAP flag and to explain
more of the details of scheduling for isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The handling of large output bulk transfers is broken; the same user
page is read over and over again. Fixed with this patch.
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four fixes for the USB 3.0 Link Power Management code. They
work around some USB 3.0 devices that don't support LPM, like the
Western Digital My Passport hard drive. They also fix an LPM disable
ref count bug that would cause LPM to remain disabled for a device
after a failed probe.
Please queue for 3.7 after the merge window closes. Several patches are
marked for stable.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=n/bA
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
USB 3.0 Link PM fixes.
Hi Greg,
Here's four fixes for the USB 3.0 Link Power Management code. They
work around some USB 3.0 devices that don't support LPM, like the
Western Digital My Passport hard drive. They also fix an LPM disable
ref count bug that would cause LPM to remain disabled for a device
after a failed probe.
Please queue for 3.7 after the merge window closes. Several patches are
marked for stable.
Sarah Sharp
SEL and PEL are in microseconds, not milliseconds. Also, fix a split
string that will trigger checkpatch warnings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The Set SEL control transfer tells a device the exit latencies
associated with a device-initated U1 or U2 exit. Since a parent hub may
initiate a transition to U1 soon after a downstream port's U1 timeout is
set, we need to make sure the device receives the Set SEL transfer
before the parent hub timeout is set.
This patch should be backported to kernels as old as 3.5, that contain
the commit 1ea7e0e8e3 "USB: Add support to
enable/disable USB3 link states."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Some USB 3.0 devices signal that they don't implement Link PM by having
all zeroes in the U1/U2 exit latencies in their SuperSpeed BOS
descriptor. Don found that a Western Digital device he has experiences
transfer errors when LPM is enabled. The lsusb shows the U1/U2 exit
latencies are set to zero:
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 22
bNumDeviceCaps 2
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
Latency Tolerance Messages (LTM) Supported
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 0 micro seconds
bU2DevExitLat 0 micro seconds
The fix is to not enable LPM for a particular link state if we find its
corresponding exit latency is zero.
This patch should be backported to kernels as old as 3.5, that contain
the commit 1ea7e0e8e3 "USB: Add support to
enable/disable USB3 link states."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Don Zickus <dzickus@redhat.com>
Cc: stable@vger.kernel.org
Before a driver is probed, we want to disable USB 3.0 Link Power
Management (LPM), in case the driver needs hub-initiated LPM disabled.
After the probe finishes, we want to attempt to re-enable LPM, order to
balance the LPM ref count.
When a probe fails (such as when libusual doesn't want to bind to a USB
3.0 mass storage device), make sure to balance the LPM ref counts by
re-enabling LPM.
This patch should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Pul ACPI & Power Management updates from Len Brown:
- acpidump utility added
- intel_idle driver now supports IVB Xeon
- turbostat utility can now count SMIs
- ACPI can now bind to USB3 hubs
- misc fixes
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
ACPI: Add new sysfs interface to export device description
ACPI: Harden acpi_table_parse_entries() against BIOS bug
tools/power/turbostat: add option to count SMIs, re-name some options
tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
intel_idle: enable IVB Xeon support
tools/power turbostat: add [-m MSR#] option
tools/power turbostat: make -M output pretty
tools/power turbostat: print more turbo-limit information
tools/power turbostat: delete unused line
tools/power turbostat: run on IVB Xeon
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
ACPI: run _OSC after ACPI_FULL_INITIALIZATION
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
tools/power/acpi/acpidump: version 20071116
tools/power/acpi/acpidump: version 20070714
tools/power/acpi/acpidump: version 20060606
tools/power/acpi/acpidump: version 20051111
xo15-ebook: convert to module_acpi_driver()
...
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ca9c9d0c92.
Rafael wants more time to work on the user api to handle port power
issues, so let's just revert the sysfs changes for now.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_get_physical_device_location()'s 2nd argument has been changed
in ACPI implementaion, so need a follow-on change in
usb_acpi_check_pld().
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As discussed at the kernel summit this year, CONFIG_EXPERIMENTAL means
nothing, so let's get rid of it.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Neil Zhang <zhangwm@marvell.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
retval is 0, and carefully assigned - and tested as non zero.
This is not useful. While we are at it remove some other bogus initialisation
in the function
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not needed, and commented out, so just remove it.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff823c79a5 ("usb: move children
to struct usb_port") forgot to consider the hub_disconnect sequence,
which releases ports before quiescing the hub, which will lead to a
use-after-free, since hub_quiesce() will try to disconnect ports'
children, which are already deallocated. Simple modprobe dummy_hcd &&
rmmod dummy_hcd will illustrate the problem.
This patch moves deallocation of hub's ports after hub_quiesce() call
in hub_disconnect().
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated and in hardirq context the interrupt is disabled.
so in usb/host code:
Removing the usage of flag IRQF_DISABLED;
Removing the calling local_irq save/restore actions in irq
handler usb_hcd_irq();
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds two sysfs files for each usb hub port to allow userspace
to control the port power policy.
For an upcoming Intel xHCI roothub, this will translate into ACPI calls
to completely power off or power on the port. As a reminder, when these
ports are completely powered off, the USB host and device will see a
physical disconnect. All future USB device connections will be lost,
and the device will not be able to signal a remote wakeup.
The control sysfs file can be written to with two options:
"on" - port power must be on.
"off" - port must be off.
The state sysfs file reports usb port's power state:
"on" - powered on
"off" - powered off
"error" - can't get power state
For now, let userspace dictate the port power off policy. Future
patches may add an in-kernel policy.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern pointed out that a USB port could potentially get powered off
when the attached USB device is in the middle of enumerating, due to
race conditions:
http://marc.info/?l=linux-usb&m=134130616707548&w=2
If that happens, we need to ensure the enumeration fails. If a call to
usb_get_descriptor() fails for a reason other than a Stall, return an
error. That should handle the case where the port is powered off.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upcoming Intel systems will have an ACPI method to control whether a USB
port can be completely powered off. The implication of powering off a
USB port is that the device and host sees a physical disconnect, and
subsequent port connections and remote wakeups will be lost.
Add a new function, usb_acpi_power_manageable(), that can be used to
find whether the usb port has ACPI power resources that can be used to
power on and off the port on these machines. Also add a new function
called usb_acpi_set_power_state() that controls the port power via these
ACPI methods.
When the USB core calls into the xHCI hub driver to power off a port,
check whether the port can be completely powered off via this new ACPI
mechanism. If so, call into these new ACPI methods. Also use the ACPI
methods when the USB core asks to power on a port.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event. Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.
According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible"). Here's a matrix of the
possible combinations:
Visible Connectible
Name Example
-------------------------------------------------------------------------
Yes No Unknown (Invalid state.)
Yes Yes Hot-plug USB ports on the outside of a laptop.
A user could freely connect and disconnect
USB devices.
No Yes Hard-wired A USB modem hard-wired to a port on the
inside of a laptop.
No No Not used The port is internal to the system and
will remain empty.
Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED. When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ACPI DSDT table, only usb root hub and usb ports are ACPI device
nodes. Originally, we bound the usb port's ACPI node to the usb device
attached to the port. However, we want to access those ACPI port
methods when the port is empty, and there's no usb_device associated
with that port.
Now that the usb port is a real device, we can bind the port's ACPI node
to struct usb_port instead.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_device structure contains an array of usb_device "children".
This array is only valid if the usb_device is a hub, so it makes no
sense to store it there. Instead, store the usb_device child
in its parent usb_port structure.
Since usb_port is an internal USB core structure, add a new function to
get the USB device child, usb_hub_find_child(). Add a new macro,
usb_hub_get_each_child(), to iterate over all the children attached to a
particular USB hub.
Remove the printing the USB children array pointer from the usb-ip
driver, since it's really not necessary.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns each USB port on a hub into a new struct device. This
new device has the USB hub interface device as its parent. The port
devices are stored in a new structure (usb_port), and an array of
usb_ports are dynamically allocated once we know how many ports the USB
hub has.
Move the port_owner variable out of usb_hub and into this new structure.
A new file will be created in the hub interface sysfs directory, so
add documentation.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel's version number is used as decimal in the bcdDevice field of
the RH descriptor. For kernel version v3.12 we would see 3.0c in lsusb.
I am not sure how important it is to stick with bcd values since this is
this way since we started git history and nobody complained (however back
then we reported only 2.6).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apps which deal with devices which also have a kernel driver, need to do
the following:
1) Check which driver is attached, so as to not detach the wrong driver
(ie detaching usbfs while another instance of the app is using the device)
2) Detach the kernel driver
3) Claim the interface
Where moving from one step to the next for both 1-2 and 2-3 consists of
a (small) race window. So currently such apps are racy and people just live
with it.
This patch adds a new ioctl which makes it possible for apps to do this
in a race free manner. For flexibility apps can choose to:
1) Specify the driver to disconnect
2) Specify to disconnect any driver except for the one named by the app
3) Disconnect any driver
Note that if there is no driver attached, the ioctl will just act like the
regular claim-interface ioctl, this is by design, as returning an error for
this condition would open a new bag of race-conditions.
Changes in v2:
-Fix indentation of if blocks where the condition spans multiple lines
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device. The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the attribute avoid_reset_quirk is work for all devices including
those devices that can't morph, convert USB_QUIRK_RESET_MORPHS to
USB_QUIRK_RESET.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For following the way the rest of the usb core does, this patch is to change
the place of setting release callback.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In USB, the word "config" already has aseparate meaning. So it will
cause confusion if use "config" as variable's name for other purposes.
This patch is to convert the "config" to "val"
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Most Logitech UVC webcams (both early models that don't advertise UVC
compatibility and newer UVC-advertised devices) require the RESET_RESUME
quirk. Instead of listing each and every model, match the devices based
on the UVC interface information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a whole class of devices (possibly from a specific vendor, or
across multiple vendors) require a quirk, explictly listing all devices
in the class make the quirks table unnecessarily large. Fix this by
allowing matching devices based on interface information.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Phy may need to change settings when port connect change.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four bug fix patches for Link PM (LPM), which are marked for
3.5-stable. There's also three patches that turn on Latency Tolerance
Messaging (LTM) for xHCI host controllers and USB 3.0 devices that support
this low power feature.
Please queue for 3.6.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJP/WCWAAoJEBMGWMLi1Gc5AjEQAIYHfWi3rhkoTpyhTyYhmzqM
/ZhAaeJXDe5VE1isfWK0mnzBz/X05MgpIxCck9CKMkcKZySJNkQFmK7iz6puGPVh
GnMQ3QkDo+9JSa7TKEX77ZG+bMkEHcAO2XbZjQs2IDfTuz+BJmQ8gFdjQGfAt/l3
KOU3k83Ci1gdtNgxqifQPBuo3o2l0L5Hn2E7XqFWQ8WUYYu1LWd2bZa/5dznq0hD
4n+ylcK0gDPa9pl7vRsLT79misdLTsJoBfjvooOE2Ms/5QXeFWRppsYRFOla8V4K
P2MjiXOCtZHN7GuxdLW776s5dZZyGZnbYNtTOSu0cOjheTC25KpmCm5XW/h5xMt3
saM6mhkSq5ZweDaLXvqV5O+WTQ2ePnubBpqR7/tVWkeUxJoK06ENKZ10dhsqfZw9
Wqcs4ze667Y3wjbBmAaF4b1bmEbhsJR/iAO2z3TLrfiAfYW3S5/4xCUCYujAXuff
n1gD75pnJJK1g4hfwFKDDNxWJtXIVqOaLMvD1x5AcGCnCG43mteruFfcS9q66LfI
uckf/PnQFAuqEx/J3dIava+yzZhNr0TMQp6aPtSCQUKgBukNf+/RRyB/pDGmYbC1
XBwqIYtv7yQ4w0DVPKd4edPP8zB8E5XMlAY/a1xvxcIa/tFBBDbVh8efXKeKrJEL
+smfSepLPwPzETe8YMNR
=G1bL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2012-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
USB: Link PM fixes and Latency Tolerance Messaging
Hi Greg,
Here's four bug fix patches for Link PM (LPM), which are marked for
3.5-stable. There's also three patches that turn on Latency Tolerance
Messaging (LTM) for xHCI host controllers and USB 3.0 devices that support
this low power feature.
Please queue for 3.6.
Sarah Sharp
Send the USB device's serial, product, and manufacturer strings to the
/dev/random driver to help seed its pools.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
USB 3.0 devices can optionally support Latency Tolerance Messaging
(LTM). Add a new sysfs file in the device directory to show whether a
device is LTM capable. This file will be present for both USB 2.0 and
USB 3.0 devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 devices may optionally support a new feature called Latency
Tolerance Messaging. If both the xHCI host controller and the device
support LTM, it should be turned on in order to give the system hardware
a better clue about the latency tolerance values of its PCI devices.
Once a Set Feature request to enable LTM is received, the USB 3.0 device
will begin to send LTM updates as its buffers fill or empty, and it can
tolerate more or less latency.
The USB 3.0 spec, section C.4.2 says that LTM should be disabled just
before the device is placed into suspend. Then the device will send an
updated LTM notification, so that the system doesn't think it should
remain in an active state in order to satisfy the latency requirements
of the suspended device.
The Set and Clear Feature LTM enable command can only be sent to a
configured device. The device will respond with an error if that
command is sent while it is in the Default or Addressed state. Make
sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(),
and don't send those commands when the device is unconfigured.
LTM should be enabled once a new configuration is installed in
usb_set_configuration(). If we end up sending duplicate Set Feature LTM
Enable commands on a switch from one installed configuration to another
configuration, that should be harmless.
Make sure that LTM is disabled before the device is unconfigured in
usb_disable_device(). If no drivers are bound to the device, it doesn't
make sense to allow the device to control the latency tolerance of the
xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a user runs `echo 0 > bConfigurationValue` for a USB 3.0 device,
usb_disable_device() is called. This function disables all drivers,
deallocates interfaces, and sets the device configuration value to 0
(unconfigured).
With the new scheme to ensure that unconfigured devices have LPM
disabled, usb_disable_device() must call usb_unlocked_disable_lpm() once
it unconfigures the device.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The USB 3.0 Set/Clear Feature U1/U2 Enable cannot be sent to a device in
the Default or Addressed state. It can only be sent to a configured
device. Change the USB core to initialize the LPM disable count to 1
(disabled), which reflects this limitation.
Change usb_set_configuration() to ensure that if the device is
unconfigured on entry, usb_lpm_disable() is not called. This avoids
sending the Clear Feature U1/U2 when the device is in the Addressed
state. When usb_set_configuration() exits with a successfully installed
configuration, usb_lpm_enable() will be called.
Once the new configuration is installed, make sure
usb_set_configuration() only calls usb_enable_lpm() if the device moved
to the Configured state. If we have unconfigured the device by sending
it a Set Configuration for config 0, don't enable LPM.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The USB 3.0 specification says that sending a Set Feature or Clear
Feature for U1/U2 Enable is not a valid request when the device is in
the Default or Addressed state. It is only valid when the device is in
the Configured state.
The original LPM patch attempted to disable LPM after the device had
been reset by hub_port_init(), before it had the configuration
reinstalled. The TI hub I tested with did not fail the Clear Feature
U1/U2 Enable request that khubd sent while it was in the addressed
state, which is why I didn't catch it.
Move the LPM disable before the device reset, so that we can send the
Clear Feature U1/U2 Enable successfully, and balance the LPM disable
count.
Also delete any calls to usb_enable_lpm() on error paths that lead to
re-enumeration. The calls will fail because the device isn't
configured, and it's not useful to balance the LPM disable count because
the usb_device is about to be destroyed before re-enumeration.
Fix the early exit path ("done" label) to call usb_enable_lpm() to
balance the LPM disable count.
Note that calling usb_reset_and_verify_device() with an unconfigured
device may fail on the first call to usb_disable_lpm(). That's because
the LPM disable count is initialized to 0 (LPM enabled), and
usb_disable_lpm() will attempt to send a Clear Feature U1/U2 request to
a device in the Addressed state. The next patch will fix that.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
We don't support sg for isoc transfers, enforce this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to convert port_owners type from void * to struct dev_state *
in order to make code more readable.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using urb->transfer_buffer we need to allocate physical contiguous buffers
for the entire transfer, which is pretty much guaranteed to fail with large
transfers.
Currently userspace works around this by breaking large transfers into multiple
urbs. For large bulk transfers this leads to all kind of complications.
This patch makes it possible for userspace to reliable submit large bulk
transfers to scatter-gather capable host controllers in one go, by using a
scatterlist to break the transfer up in managable chunks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.
This patch besides adding the new ioctl also adds flags for the following
existing capabilities:
USBDEVFS_CAP_ZERO_PACKET, available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION, available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3
Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.
Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.
The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iso data buffers may have holes in them if some packets were short, so for
iso urbs we should always copy the entire buffer, just like the regular
processcompl does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The host controller port status register supports CAS (Cold Attach
Status) bit. This bit could be set when USB3.0 device is connected
when system is in Sx state. When the system wakes to S0 this port
status with CAS bit is reported and this port can't be used by any
device.
When CAS bit is set the port should be reset by warm reset. This
was not supported by xhci driver.
The issue was found when pendrive was connected to suspended
platform. The link state of "Compliance Mode" was reported together
with CAS bit. This link state was also not supported by xhci and
core/hub.c.
The CAS bit is defined only for xhci root hub port and it is
not supported on regular hubs. The link status is used to force
warm reset on port. Make the USB core issue a warm reset when port
is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver
to report 'compliance mode' when the CAS is set. This force warm reset
on the root hub port.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 10d674a82e "USB: When
hot reset for USB3 fails, try warm reset."
Signed-off-by: Stanislaw Ledwon <staszek.ledwon@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
This lets us catch the USB fixes that went into 3.5-rc3 into this branch,
as we want them here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TEAC's UD-H01 (and probably other devices) have a gap in the interface
number allocation of their descriptors:
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 220
bNumInterfaces 3
[...]
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
[...]
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 2
bInterfaceCount 2
bFunctionClass 1 Audio
bFunctionSubClass 0
bFunctionProtocol 32
iFunction 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
[...]
Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.
The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.
In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.
Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: bEN <ml_all@circa.be>
Reported-by: Ivan Perrone <ivanperrone@hotmail.com>
Tested-by: ivan perrone <ivanperrone@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oodF
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xhci: Bug fixes for 3.5
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
We check "u1_params" instead of checking "u2_params".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Ensure that intfdata always is NULL if no driver is bound:
1) drvdata is for a driver to store a pointer to driver specific data
2) If no driver is bound, there is no driver specific data associated with
the device
3) Thus logically drvdata should be NULL if no driver is bound.
We already set intfdata to NULL when a driver is unbound, to ensure that
intfdata will be NULL even if the drivers disconnect method does not properly
clear it. This ensures that intfdata will also be NULL after a failed probe,
even if the driver's probe method left a (likely dangling) pointer in there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some composite USB devices provide multiple interfaces
with different functions, all using "vendor-specific"
for class/subclass/protocol. Another OS use interface
numbers to match the driver and interface. It seems
these devices are designed with that in mind - using
static interface numbers for the different functions.
This adds support for matching against the
bInterfaceNumber, allowing such devices to be supported
without having to resort to testing against interface
number whitelists and/or blacklists in the probe.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This class was not named properly years ago, and it turns out that tools
like udev can't properly see the devices in this class after booting due
to the fact that there is a bus with the same name in the system.
Changing this to "usbmisc" fixes this problem, and it solves the problem
for the future when we want to unify classes and busses.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
When CONFIG_PM=n, make sure that the usb_[unlocked_][en/dis]able_lpm
declarations are visible in include/linux/usb.h, and exported from
drivers/usb/core/hub.c.
Before this patch, if CONFIG_USB_SUSPEND was turned off, it would cause
build errors:
drivers/usb/core/hub.c: In function 'usb_disable_lpm':
drivers/usb/core/hub.c:3394:2: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/hub.c: At top level:
drivers/usb/core/hub.c:3424:6: warning: conflicting types for 'usb_enable_lpm' [enabled by default]
drivers/usb/core/hub.c:3394:2: note: previous implicit declaration of 'usb_enable_lpm' was here
drivers/usb/core/driver.c: In function 'usb_probe_interface':
drivers/usb/core/driver.c:339:2: error: implicit declaration of function 'usb_unlocked_disable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/driver.c:364:3: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c: In function 'usb_set_interface':
drivers/usb/core/message.c:1314:2: error: implicit declaration of function 'usb_disable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c:1323:3: error: implicit declaration of function 'usb_enable_lpm' [-Werror=implicit-function-declaration]
drivers/usb/core/message.c:1368:2: error: implicit declaration of function 'usb_unlocked_enable_lpm' [-Werror=implicit-function-declaration]
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Chen Peter-B29397 <B29397@freescale.com>
There exist races in devio.c, below is one case,
and there are similar races in destroy_async()
and proc_unlinkurb(). Remove these races.
cancel_bulk_urbs() async_completed()
------------------- -----------------------
spin_unlock(&ps->lock);
list_move_tail(&as->asynclist,
&ps->async_completed);
wake_up(&ps->wait);
Lead to free_async() be triggered,
then urb and 'as' will be freed.
usb_unlink_urb(as->urb);
===> refer to the freed 'as'
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oncaphillis <oncaphillis@snafu.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several places where the USB core needs to disable USB 3.0
Link PM:
- usb_bind_interface
- usb_unbind_interface
- usb_driver_claim_interface
- usb_port_suspend/usb_port_resume
- usb_reset_and_verify_device
- usb_set_interface
- usb_reset_configuration
- usb_set_configuration
Use the new LPM disable/enable functions to temporarily disable LPM
around these critical sections.
We need to protect the critical section around binding and unbinding USB
interface drivers. USB drivers may want to disable hub-initiated USB
3.0 LPM, which will change the value of the U1/U2 timeouts that the xHCI
driver will install. We need to disable LPM completely until the driver
is bound to the interface, and the driver has a chance to enable
whatever alternate interface setting it needs in its probe routine.
Then re-enable USB3 LPM, and recalculate the U1/U2 timeout values.
We also need to disable LPM in usb_driver_claim_interface,
because drivers like usbfs can bind to an interface through that
function. Note, there is no way currently for userspace drivers to
disable hub-initiated USB 3.0 LPM. Revisit this later.
When a driver is unbound, the U1/U2 timeouts may change because we are
unbinding the last driver that needed hub-initiated USB 3.0 LPM to be
disabled.
USB LPM must be disabled when a USB device is going to be suspended.
The USB 3.0 spec does not define a state transition from U1 or U2 into
U3, so we need to bring the device into U0 by disabling LPM before we
can place it into U3. Therefore, call usb_unlocked_disable_lpm() in
usb_port_suspend(), and call usb_unlocked_enable_lpm() in
usb_port_resume(). If the port suspend fails, make sure to re-enable
LPM by calling usb_unlocked_enable_lpm(), since usb_port_resume() will
not be called on a failed port suspend.
USB 3.0 devices lose their USB 3.0 LPM settings (including whether USB
device-initiated LPM is enabled) across device suspend. Therefore,
disable LPM before the device will be reset in
usb_reset_and_verify_device(), and re-enable LPM after the reset is
complete and the configuration/alt settings are re-installed.
The calculated U1/U2 timeout values are heavily dependent on what USB
device endpoints are currently enabled. When any of the enabled
endpoints on the device might change, due to a new configuration, or new
alternate interface setting, we need to first disable USB 3.0 LPM, add
or delete endpoints from the xHCI schedule, install the new interfaces
and alt settings, and then re-enable LPM. Do this in usb_set_interface,
usb_reset_configuration, and usb_set_configuration.
Basically, there is a call to disable and then enable LPM in all
functions that lock the bandwidth_mutex. One exception is
usb_disable_device, because the device is disconnecting or otherwise
going away, and we should not care about whether USB 3.0 LPM is enabled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There are various functions within the USB core that will need to
disable USB 3.0 link power states. For example, when a USB device
driver is being bound to an interface, we need to disable USB 3.0 LPM
until we know if the driver will allow hub-initiated LPM transitions.
Another example is when the USB core is switching alternate interface
settings. The USB 3.0 timeout values are dependent on what endpoints
are enabled, so we want to ensure that LPM is disabled until the new alt
setting is fully installed.
Multiple functions need to disable LPM, and those functions can even be
nested. For example, usb_bind_interface() could disable LPM, and then
call into the driver probe function, which may attempt to switch to a
different alt setting. Therefore, we need to keep a count of the number
of functions that require LPM to be disabled at any point in time.
Introduce two new USB core API calls, usb_disable_lpm() and
usb_enable_lpm(). These functions increment and decrement a new
variable in the usb_device, lpm_disable_count. If usb_disable_lpm()
fails, it will call usb_enable_lpm() in order to balance the
lpm_disable_count.
These two new functions must be called with the bandwidth_mutex locked.
If the bandwidth_mutex is not already held by the caller, it should
instead call usb_unlocked_disable_lpm() and usb_enable_lpm(), which take
the bandwidth_mutex before calling usb_disable_lpm() and
usb_enable_lpm(), respectively.
Introduce a new variable (timeout) in the usb3_lpm_params structure to
keep track of the currently enabled U1/U2 timeout values. When
usb_disable_lpm() is called, and the USB device has the U1 or U2
timeouts set to a non-zero value (meaning either device-initiated or
hub-initiated LPM is enabled), attempt to disable LPM, regardless of the
state of the lpm_disable_count. We want to ensure that all callers can
be guaranteed that LPM is disabled if usb_disable_lpm() returns zero.
Otherwise the following scenario could occur:
1. Driver A is being bound to interface 1. usb_probe_interface()
disables LPM. Driver A doesn't care if hub-initiated LPM is enabled, so
even though usb_disable_lpm() fails, the probe of the driver continues,
and the bandwidth mutex is dropped.
2. Meanwhile, Driver B is being bound to interface 2.
usb_probe_interface() grabs the bandwidth mutex and calls
usb_disable_lpm(). That call should attempt to disable LPM, even
though the lpm_disable_count is set to 1 by Driver A.
For usb_enable_lpm(), we attempt to enable LPM only when the
lpm_disable_count is zero. If some step in enabling LPM fails, it will
only have a minimal impact on power consumption, and all USB device
drivers should still work properly. Therefore don't bother to return
any error codes.
Don't enable device-initiated LPM if the device is unconfigured. The
USB device will only accept the U1/U2_ENABLE control transfers in the
configured state. Do enable hub-initiated LPM in that case, since
devices are allowed to accept the LGO_Ux link commands in any state.
Don't enable or disable LPM if the device is marked as not being LPM
capable. This can happen if:
- the USB device doesn't have a SS BOS descriptor,
- the device's parent hub has a zeroed bHeaderDecodeLatency value, or
- the xHCI host doesn't support LPM.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There are several different exit latencies associated with coming out of
the U1 or U2 lower power link state.
Device Exit Latency (DEL) is the maximum time it takes for the USB
device to bring its upstream link into U0. That can be found in the
SuperSpeed Extended Capabilities BOS descriptor for the device. The
time it takes for a particular link in the tree to exit to U0 is the
maximum of either the parent hub's U1/U2 DEL, or the child's U1/U2 DEL.
Hubs introduce a further delay that effects how long it takes a child
device to transition to U0. When a USB 3.0 hub receives a header
packet, it takes some time to decode that header and figure out which
downstream port the packet was destined for. If the port is not in U0,
this hub header decode latency will cause an additional delay for
bringing the child device to U0. This Hub Header Decode Latency is
found in the USB 3.0 hub descriptor.
We can use DEL and the header decode latency, along with additional
latencies imposed by each additional hub tier, to figure out the exit
latencies for both host-initiated and device-initiated exit to U0.
The Max Exit Latency (MEL) is the worst-case time it will take for a
host-initiated exit to U0, based on whether U1 or U2 link states are
enabled. The ping or packet must traverse the path to the device, and
each hub along the way incurs the hub header decode latency in order to
figure out which device the transfer was bound for. We say worst-case,
because some hubs may not be in the lowest link state that is enabled.
See the examples in section C.2.2.1.
Note that "HSD" is a "host specific delay" that the power appendix
architect has not been able to tell me how to calculate. There's no way
to get HSD from the xHCI registers either, so I'm simply ignoring it.
The Path Exit Latency (PEL) is the worst-case time it will take for a
device-initiate exit to U0 to place all the links from the device to the
host into U0.
The System Exit Latency (SEL) is another device-initiated exit latency.
SEL is useful for USB 3.0 devices that need to send data to the host at
specific intervals. The device may send an NRDY to indicate it isn't
ready to send data, then put its link into a lower power state. If it
needs to have that data transmitted at a specific time, it can use SEL
to back calculate when it will need to bring the link back into U0 to
meet its deadlines.
SEL is the worst-case time from the device-initiated exit to U0, to when
the device will receive a packet from the host controller. It includes
PEL, the time it takes for an ERDY to get to the host, a host-specific
delay for the host to process that ERDY, and the time it takes for the
packet to traverse the path to the device. See Figure C-2 in the USB
3.0 bus specification.
Note: I have not been able to get good answers about what the
host-specific delay to process the ERDY should be. The Intel HW
developers say it will be specific to the platform the xHCI host is
integrated into, and they say it's negligible. Ignore this too.
Separate from these four exit latencies are the U1/U2 timeout values we
program into the parent hubs. These timeouts tell the hub to attempt to
place the device into a lower power link state after the link has been
idle for that amount of time.
Create two arrays (one for U1 and one for U2) to store mel, pel, sel,
and the timeout values. Store the exit latency values in nanosecond
units, since that's the smallest units used (DEL is in us, but the Hub
Header Decode Latency is in ns).
If a USB 3.0 device doesn't have a SuperSpeed Extended Capabilities BOS
descriptor, it's highly unlikely it will be able to handle LPM requests
properly. So it's best to disable LPM for devices that don't have this
descriptor, and any children beneath it, if it's a USB 3.0 hub. Warn
users when that happens, since it means they have a non-compliant USB
3.0 device or hub.
This patch assumes a simplified design where links deep in the tree will
not have U1 or U2 enabled unless all their parent links have the
corresponding LPM state enabled. Eventually, we might want to allow a
different policy, and we can revisit this patch when that happens.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Refactor the code that sets the usb_device flag to indicate the device
support link power management (lpm_capable). The current code sets
lpm_capable unconditionally if the USB devices have a USB 2.0 Extended
Capabilities Descriptor. USB 3.0 devices can also have that descriptor,
but the xHCI driver code that uses lpm_capable will not run the USB 2.0
LPM test for devices under the USB 3.0 roothub. Therefore, it's fine
only set lpm_capable for high speed devices in this refactoring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The BOS descriptor is normally fetched and stored in the usb_device->bos
during enumeration. USB 3.0 roothubs don't undergo enumeration, but we
need them to have a BOS descriptor, since each xHCI host has a different
U1 and U2 exit latency. Make sure to fetch the BOS descriptor for USB
3.0 roothubs. It will be freed when the roothub usb_device is released.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
USB2 LPM is disabled when device begin to suspend and enabled after device
is resumed. That's because USB spec does not define the transition from
U1/U2 state to U3 state.
If usb_port_suspend() fails, usb_port_resume() is never called, and USB2 LPM
is disabled in this situation. Enable USB2 LPM if port suspend fails.
This patch should be backported to kernels as old as 3.2, that contain
the commit 65580b4321 "xHCI: set USB2
hardware LPM".
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Commit da0af6e ("usb: Bind devices to ACPI devices when possible") really
tries to force-bind devices even when impossible, unlike what it says in
the subject.
CONFIG_ACPI is not an indication that ACPI tables are actually present, nor
is an indication that any USB relevant information is present in them. There
is no reason to fail the creation of a USB bus if it can't bind it to
ACPI device during initialization.
On systems with CONFIG_ACPI set but without ACPI tables it would cause a
boot panic.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1554) fixes a lockdep false-positive report. The
problem arises because lockdep is unable to deal with the
tree-structured locks created by the device core and sysfs.
This particular problem involves a sysfs attribute method that
unregisters itself, not from the device it was called for, but from a
descendant device. Lockdep doesn't understand the distinction and
reports a possible deadlock, even though the operation is safe.
This is the sort of thing that would normally be handled by using a
nested lock annotation; unfortunately it's not feasible to do that
here. There's no sensible way to tell sysfs when attribute removal
occurs in the context of a parent attribute method.
As a workaround, the patch adds a new flag to struct attribute
telling sysfs not to inform lockdep when it acquires a readlock on a
sysfs_dirent instance for the attribute. The readlock is still
acquired, but lockdep doesn't know about it and hence does not
complain about impossible deadlock scenarios.
Also added are macros for static initialization of attribute
structures with the ignore_lockdep flag set. The three offending
attributes in the USB subsystem are converted to use the new macros.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Tejun Heo <tj@kernel.org>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the usb-serial support for dynamic IDs in sync with the usb
support. This enables readout of dynamic device IDs for
usb-serial drivers. Common code is exported from the usb core
system and reused by the usb-serial bus driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables the current list of dynamic IDs to be read out through
either new_id or remove_id.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f397d7c4c5.
This series isn't quite ready for 3.5 just yet, so revert it and give
the author more time to get it correct.
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bebc56d58d.
The call here is fragile and not well thought out, so revert it, it's
not fully baked yet and I don't want this to go into 3.5.
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no default value is specified, then 'n' is used so the default value
used here is not needed. Furthermore, we should never change default
values depending on EXPERT mode. EXPERT mode should only make options
visible, not change them.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move child's pointer to the struct usb_hub_port since the child device
is directly associated with the port. Provide usb_get_hub_child_device()
to get child's pointer.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add struct usb_hub_port pointer port_data in the struct usb_hub and allocate
struct usb_hub_port perspectively for each ports to store private data.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI offers two methods that allow us to infer whether or not a USB port
is removable. The _PLD method gives us information on whether the port is
"user visible" or not. If that's not present then we can fall back to the
_UPC method which tells us whether or not a port is connectable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Built-in USB devices will typically have a representation in the system
ACPI tables. Add support for binding the two together so the USB code can
make use of the associated methods.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It took me surprisingly long to find the location where the Linux
Foundation vendor id (0x1d6b) is set for the root hubs. A minor update
to three comments makes those locations (trivially) greppable.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some HCDs usb_unlink_urb() can directly call the
completion handler. That limits the spinlocks that can
be taken in the handler to locks not held while calling
usb_unlink_urb()
To prevent a race with resubmission, this patch exposes
usbcore's infrastructure for blocking submission, uses it
and so drops the lock without causing a race in usbhid.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.
Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit
fccf4e8620 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Seagate Goflex USB3.0 device is attached to VIA xHCI
host, sometimes the device will downgrade mode to high speed.
By the USB analyzer, I found the device finished the link
training process and worked at superspeed mode. But the device
descriptor got from the device shows the device works at 2.1.
It is very strange and seems like the device controller of
Seagate Goflex has a little confusion.
The first 8 bytes of device descriptor should be:
12 01 00 03 00 00 00 09
But the first 8 bytes of wrong device descriptor are:
12 01 10 02 00 00 00 40
The wrong device descriptor caused the initialization of mass
storage failed. After a while, the device would be recognized
as a high speed device and works fine.
This patch will warm reset the device to fix the issue after
finding the bcdUSB field of device descriptor isn't 0x0300
but the speed mode of device is superspeed.
This patch should be backported to kernels as old as 3.2, or ones that
contain the commit 75d7cf72ab "usbcore:
refine warm reset logic".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Acked-by: Andiry Xu <Andiry.Xu@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch (as1533) fixes a race between root-hub suspend and remote
wakeup. If a wakeup event occurs while a root hub is suspending, it
might not cause the suspend to fail. Although the host controller
drivers check for pending wakeup events at the start of their
bus_suspend routines, they generally do not check for wakeup events
while the routines are running.
In addition, if a wakeup event occurs any time after khubd is frozen
and before the root hub is fully suspended, it might not cause a
system sleep transition to fail. For example, the host controller
drivers do not fail root-hub suspends when a connect-change event is
pending.
To fix both these issues, this patch causes hcd_bus_suspend() to query
the controller driver's hub_status_data method after a root hub is
suspended, if the root hub is enabled for wakeup. Any pending status
changes will count as wakeup events, causing the root hub to be
resumed and the overall suspend to fail with -EBUSY.
A significant point is that not all events are reflected immediately
in the status bits. Both EHCI and UHCI controllers notify the CPU
when remote wakeup begins on a port, but the port's suspend-change
status bit doesn't get set until after the port has completed the
transition out of the suspend state, some 25 milliseconds later.
Consequently, the patch will interpret any nonzero return value from
hub_status_data as indicating a pending event, even if none of the
status bits are set in the data buffer. Follow-up patches make the
necessary changes to ehci-hcd and uhci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Chen Peter-B29397 <B29397@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1532) fixes a mistake in the USB suspend code. When the
system is going to sleep, we should ignore errors in powering down USB
devices, because they don't really matter. The devices will go to low
power anyway when the entire USB bus gets suspended (except for
SuperSpeed devices; maybe they will need special treatment later).
However we should not ignore errors in suspending root hubs,
especially if the error indicates that the suspend raced with a wakeup
request. Doing so might leave the bus powered on while the system was
supposed to be asleep, or it might cause the suspend of the root hub's
parent controller device to fail, or it might cause a wakeup request
to be ignored.
The patch fixes the problem by ignoring errors only when the device in
question is not a root hub.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chen Peter <B29397@freescale.com>
CC: <stable@vger.kernel.org>
Tested-by: Chen Peter <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed to catch the resume bug that was bothering lots of us from
testing some XHCI bug fixes in the suspend/resume path.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1534c) updates the documentation for usb_unlink_urb and
related functions. It explains that the caller must prevent the URB
being unlinked from getting deallocated while the unlink is taking
place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1517b) fixes an error in the USB scatter-gather library.
The library code uses urb->dev to determine whether or nor an URB is
currently active; the completion handler sets urb->dev to NULL.
However the core unlinking routines need to use urb->dev. Since
unlinking always racing with completion, the completion handler must
not clear urb->dev -- it can lead to invalid memory accesses when a
transfer has to be cancelled.
This patch fixes the problem by getting rid of the lines that clear
urb->dev after urb has been submitted. As a result we may end up
trying to unlink an URB that failed in submission or that has already
completed, so an extra check is added after each unlink to avoid
printing an error message when this happens. The checks are updated
in both sg_complete() and sg_cancel(), and the second is updated to
match the first (currently it prints out unnecessary warning messages
if a device is unplugged while a transfer is in progress).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Illia Zaitsev <I.Zaitsev@adbglobal.com>
CC: Ming Lei <tom.leiming@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
Non-hub device has no child, and even a real USB hub has ports far
less than USB_MAXCHILDREN, so there is no need using a fix array for
child devices, just allocate it dynamically according real port
number.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel doc entry for usb_unlink_urb() contains the phrase "This
request is always asynchronous.". The "always" leads to the assumption
that the ->complete() callback is not called from within
usb_unlink_urb(). This is not true. The HCD is allowed to call the
->complete() from within ->urb_dequeue() if it is appropriate for the
hardware.
This patch updates the kernel doc so usb-device driver authors make sure
to drop all locks (and make sure it is okay to drop them) which are
acquired by the complete callback before calling usb_unlink_urb().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shows up on ia64 builds (and possibly elsewhere) for configs that
don't set PM_RUNTIME or PM_SLEEP as follows:
drivers/usb/core/hcd-pci.c:383:12: warning: 'suspend_common' defined but not used
drivers/usb/core/hcd-pci.c:438:12: warning: 'resume_common' defined but not used
As per above, the functions are only used if RUNTIME/SLEEP are set,
so make the two functions conditional on these Kconfig values.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pull in the xhci changes and the other fixes and device id
updates that were done in Linus's tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Now that USB 3.0 hub remote wakeup on port status changes is enabled,
and USB 3.0 device remote wakeup is handled in the USB core properly,
let's turn on auto-suspend for all USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch takes care of the race condition between the Function Wake
Device Notification and the auto-suspend timeout for this situation:
Roothub
| (U3)
hub A
| (U3)
hub B
| (U3)
device C
When device C signals a resume, the xHCI driver will set the wakeup_bits
for the roothub port that hub A is attached to. However, since USB 3.0
hubs do not set a link state change bit on device-initiated resume, hub
A will not indicate a port event when polled. Without this patch, khubd
will notice the wakeup-bits are set for the roothub port, it will resume
hub A, and then it will poll the events bits for hub A and notice that
nothing has changed. Then it will be suspended after 2 seconds.
Change hub_activate() to look at the port link state for each USB 3.0
hub port, and set hub->change_bits if the link state is U0, indicating
the device has finished resume. Change the resume function called by
hub_events(), hub_handle_remote_wakeup(), to check the link status
for resume instead of just the port's wakeup_bits.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved). Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.
When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain. The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.
However, the parent hubs in the resumed path will not set their link
state change bit. Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller. Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.
First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes. Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).
Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed. When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.
We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver. This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.
Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.
This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached). The other cases will be covered
in a second patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor the code to check for a remote wakeup on a port into its own
function. Keep the behavior the same, and set connect_change in
hub_events if the device disconnected on resume. Cleanup references to
hdev->children[i-1] to use a common variable.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
USB 3.0 hubs have a different remote wakeup policy than USB 2.0 hubs.
USB 2.0 hubs, once they have remote wakeup enabled, will always send
remote wakes when anything changes on a port.
However, USB 3.0 hubs have a per-port remote wake up policy that is off
by default. The Set Feature remote wake mask can be changed for any
port, enabling remote wakeup for a connect, disconnect, or overcurrent
event, much like EHCI and xHCI host controller "wake on" port status
bits. The bits are cleared to zero on the initial hub power on, or
after the hub has been reset.
Without this patch, when a USB 3.0 hub gets suspended, it will not send
a remote wakeup on device connect or disconnect. This would show up to
the user as "dead ports" unless they ran lsusb -v (since newer versions
of lsusb use the sysfs files, rather than sending control transfers).
Change the hub driver's suspend method to enable remote wake up for
disconnect, connect, and overcurrent for all ports on the hub. Modify
the xHCI driver's roothub code to handle that request, and set the "wake
on" bits in the port status registers accordingly.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The USB 3.0 bus specification introduces a new type of power management
called function suspend. The idea is to be able to suspend different
functions (i.e. a scanner or an SD card reader on a USB printer)
independently. A device can be in U0, but have one or more functions
suspended. Thus, signaling a function resume with the standard device
remote wake signaling was not possible.
Instead, a device will (without prompt from the host) send a "device
notification" for the function remote wake. A new Set Feature Function
Remote Wake was developed to turn remote wake up on and off for each
function.
USB 3.0 devices can still go into device suspend (U3), and signal a
remote wakeup to bring the link back into U1. However, they now use the
function remote wake device notification to allow the host to know which
function woke the device from U3.
The spec is a bit ambiguous about whether a function is allowed to
signal a remote wakeup if the function has been enabled for remote
wakeup, but not placed in function suspend before the device is placed
into U3.
Section 9.2.5.1 says "Suspending a device with more than one function
effectively suspends all the functions within the device." I interpret
that to mean that putting a device in U3 suspends all functions, and
thus if the host has previously enabled remote wake for those functions,
it should be able to signal a remote wake up on port status changes.
However, hub vendors may have a different interpretation, and it can't
hurt to put the function into suspend before putting the device into U3.
I cannot get an answer out of the USB 3.0 spec architects about this
ambiguity, so I'm erring on the safe side and always suspending the
first function before placing the device in U3. Note, this code should
be fixed if we ever find any USB 3.0 devices that have more than one
function.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When the USB 3.0 hub support went in, I disabled selective suspend for
all external USB 3.0 hubs because they used a different mechanism to
enable remote wakeup. In fact, other USB 3.0 devices that could signal
remote wakeup would have been prevented from going into suspend because
they would have stalled the SetFeature Device Remote Wakeup request.
This patch adds support for the USB 3.0 way of enabling remote wake up
(with a SetFeature Function Suspend request), and enables selective
suspend for all hubs during hub_probe. It assumes that all USB 3.0 have
only one "function" as defined by the interface association descriptor,
which is true of all the USB 3.0 devices I've seen so far. FIXME if
that turns out to change later.
After a device signals a remote wakeup, it is supposed to send a Device
Notification packet to the host controller, signaling which function
sent the remote wakeup. The host can then put any other functions back
into function suspend. Since we don't have support for function suspend
(and no devices currently support it), we'll just assume the hub
function will resume the device properly when it received the port
status change notification, and simply ignore any device notification
events from the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Hubs have a flag to indicate whether a given port carries removable devices
or not. This is not strictly accurate in that some built-in devices
will be flagged as removable, but followup patches will make use of platform
data to make this more reliable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace may want to make policy decisions based on whether or not a
given USB device is removable. Add a per-device member and support
for exposing it in sysfs. Information sources to populate it will be
added later.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
People have complained that debugging code shouldn't alter the flow of
control; it should restrict itself to printing out warnings and error
messages. Bowing to popular opinion, this patch (as1518) changes the
debugging checks in usb_submit_urb() to follow this guideline.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Keith Packard <keithp@keithp.com>
CC: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1514) cleans up some places where new_id and remove_id
sysfs attributes are created and deleted. Handling both attributes in
a single routine rather than a pair of routines makes the code
smaller. It also prevents certain kinds of errors, like one we
currently have in the USB subsystem: The removeid attribute is often
created even when newid isn't (because the driver's no_dynamid_id flag
is set).
In the case of the PCMCIA subsystem, the newid attribute is created
but never explicitly deleted. The patch adds a deletion routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of the removal of get_driver()/put_driver(), this patch
(as1511) changes all the places that add dynamic IDs for drivers.
Since these additions are done by writing to the drivers' sysfs
attribute files, and the attributes are removed when the drivers are
unregistered, there is no reason to take an extra reference to the
drivers.
The one exception is the pci-stub driver, which calls pci_add_dynid()
as part of its registration. But again, there's no reason to take an
extra reference here, because the driver can't be unloaded while it is
being registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This eliminates the last instance of a function's behavior
controlled by a parameter as Linus hates such things.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do the cleanup to avoid behaviorial parameters Linus
requested.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
both callers of device_get_devnode() are only interested in lower 16bits
and nobody tries to return anything wider than 16bit anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If a driver does not support the suspend/resume callbacks
it will be forcibly disconnected. There is no reason to check
for support of the callbacks after that.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Guillemot Webcam Hercules Dualpix Exchange camera
has been reported with a second ID.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is in succession of previous patch
commit c842114792
xHCI: Adding #define values used for hub descriptor
Hub descriptors characteristics #defines values are added in
hub_configure() in place of magic numbers as asked by Alan Stern.
And the indentation for switch and case is changed to be same.
Some #defines values are added in ch11.h for defining hub class
protocols and used in hub.c and hcd.c in which magic values were
used for hub class protocols.
Signed-off-by: Aman Deep <amandeep3986@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new field num_mapped_sgs to struct urb so that we have a place to
store the number of mapped entries and can also retain the original
value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma()
would overwrite this with the number of mapped entries, which would
break dma_unmap_sg() because it requires the original number of entries.
This fixes warnings like the following when using USB storage devices:
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695()
ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1]
Modules linked in: ohci_hcd ehci_hcd
Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319
Call Trace:
<IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98
[<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43
[<ffffffff811fa5ae>] check_unmap+0x4e4/0x695
[<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50
[<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117
[<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188
[<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22
[<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0
[<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd]
[<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd]
[<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd]
...
---[ end trace f29ac88a5a48c580 ]---
Mapped at:
[<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139
[<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478
[<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa
[<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de
[<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pulls in the latest USB bugfixes and helps a few of the drivers
merge nicer in the future due to changes in both branches.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 16-MB global limit on memory used by usbfs isn't suitable for all
people. It's a reasonable default, but there are applications
(especially for SuperSpeed devices) that need a lot more.
This patch (as1498) creates a writable module parameter for usbcore to
control the global limit. The default is still 16 MB, but users can
change it at runtime, even after usbcore has been loaded. As a
special case, setting the value to 0 is treated the same as the hard
limit of 2047 MB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For a long time people have complained about the limitations imposed
by usbfs. URBs coming from userspace are not allowed to have transfer
buffers larger than a more-or-less arbitrary maximum.
While it is generally a good idea to avoid large transfer buffers
(because the data has to be bounced to/from a contiguous kernel-space
buffer), it's not the kernel's job to enforce such limits. Programs
should be allowed to submit URBs as large as they like; if there isn't
sufficient contiguous memory available then the submission will fail
with a simple ENOMEM error.
On the other hand, we would like to prevent programs from submitting a
lot of small URBs and using up all the DMA-able kernel memory. To
that end, this patch (as1497) replaces the old limits on individual
transfer buffers with a single global limit on the total amount of
memory in use by usbfs. The global limit is set to 16 MB as a nice
compromise value: not too big, but large enough to hold about 300 ms
of data for high-speed transfers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1496) unifies the error-return pathways of several
functions in the usbfs driver. This is not a very important change by
itself; it merely prepares the way for the next patch in this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move usb_translate_errors from usb core to linux/usb.h as it is meant to
be accessed from drivers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When adding the ID of a composite device dynamically to a driver, all
hitherto unbound interfaces are bound to this driver regardless of their
class, which may not be intended.
The patch adds the option to tell the targeted interface class to a driver
via the "new_id" attribute, in addition to the device ID.
Also, it appends the ABI documentation accordingly.
Example:
$ echo "1234 2a2a ff" >/sys/bus/usb-serial/drivers/option1/new_id
will bind only vendor-specific interfaces to the 3G driver.
Signed-off-by: Josua Dietze <digidietze@draisberghof.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The HCD_FLAG_SAW_IRQ flag was introduced in order to catch IRQ routing
errors: If an URB was unlinked and the host controller hadn't gotten
any IRQs, it seemed likely that the IRQs were directed to the wrong
vector.
This warning hasn't come up in many years, as far as I know; interrupt
routing now seems to be well under control. Therefore there's no
reason to keep the flag around any more. This patch (as1495) finally
removes it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch contains additional affected webcam models, on top of the
patches commited to linux-next 2394d67e44
and 5b253d88cc
Signed-off-by: sordna <sordna@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We've had another report of the "chipmunk" sound on a Logitech C600 webcam.
This patch resolves the issue.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of ra.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
usb, xhci: Clear warm reset change event during init
xhci: Set slot and ep0 flags for address command.
usb, xhci: fix lockdep warning on endpoint timeout
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. A companion
patch changes the PM core's behavior, but we also need to change the
USB core. In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I noticed on my Panther Point system that I wasn't getting hotplug events
for my usb3.0 disk on a usb3 port. I tracked it down to the fact that the
system had the warm reset change bit still set. This seemed to block future
events from being received, including a hotplug event.
Clearing this bit during initialization allowed the hotplug event to be
received and the disk to be recognized correctly.
This patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
To add USB 3.0 link power management (LPM), we need to know what the U1
and U2 exit latencies are for the xHCI host controller. External USB 3.0
hubs report these values through the SuperSpeed Capabilities descriptor in
the BOS descriptor. Make the USB 3.0 roothub for the xHCI host behave
like an external hub and return the BOS descriptors.
The U1 and U2 exit latencies will vary across each host controller, so we
need to dynamically fill those values in by reading the exit latencies out
of the xHC registers. Make the roothub code in the USB core handle
hub_control() returning the length of the data copied.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* pm-runtime:
PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
PM / Runtime: Replace dev_dbg() with trace_rpm_*()
PM / Runtime: Introduce trace points for tracing rpm_* functions
PM / Runtime: Don't run callbacks under lock for power.irq_safe set
USB: Add wakeup info to debugging messages
PM / Runtime: pm_runtime_idle() can be called in atomic context
PM / Runtime: Add macro to test for runtime PM events
PM / Runtime: Add might_sleep() to runtime PM functions
My webcam is a Logitech C300 and I get "chipmunk"ed squeaky sound.
The following trivial patch fixes it.
Signed-off-by: Jon Levell <linuxusb@coralbark.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add to the dev_state and alloc_async structures the user namespace
corresponding to the uid and euid. Pass these to kill_pid_info_as_uid(),
which can then implement a proper, user-namespace-aware uid check.
Changelog:
Sep 20: Per Oleg's suggestion: Instead of caching and passing user namespace,
uid, and euid each separately, pass a struct cred.
Sep 26: Address Alan Stern's comments: don't define a struct cred at
usbdev_open(), and take and put a cred at async_completed() to
ensure it lasts for the duration of kill_pid_info_as_cred().
Signed-off-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"length" is type size_t so the cast to unsigned int truncates the
upper bytes. This isn't an issue in real life (I've checked the
callers) but it's a bit messy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1487) improves the usbcore debugging output for port
suspend and bus suspend, by stating whether or not remote wakeup is
enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In the usb printer class specific request get_device_id the value of
wIndex is (interface << 8 | altsetting) instead of just interface.
This enables the detection of some printers with libusb.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthias Dellweg <2500@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed. Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1486) implements the kernel's new wakeup policy for USB
host controllers. Since they don't generate wakeup requests on their
but merely forward requests from their root hubs toward the CPU, they
should be enabled for wakeup by default.
Also, to be compliant with both the old and new policies, root hubs
should not be enabled for remote wakeup by default. Userspace must
enable it explicitly if it is desired.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds sysfs support to xHCI usb2 hardware LPM, so developer can
enable and disable usb2 hardware LPM manually for test purpose.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check device's LPM capability by examining the bmAttibutes field of the
USB2.0 Extension Descriptor.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit gets BOS(Binary Device Object Store) descriptor set for Super
Speed devices and High Speed devices which support BOS descriptor.
BOS descriptor is used to report additional USB device-level capabilities
that are not reported via the Device descriptor. By getting BOS descriptor
set, driver can check device's device-level capability such as LPM
capability.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a hot reset (standard USB port reset) fails on a USB 3.0 port, the
host controller transitions to the "Error" state. It reports the port
link state as "Inactive", sets the link state change flag, and (if the
device disconnects) also reports the disconnect and connect change status.
It's also supposed to transition the link state to "RxDetect", but the NEC
µPD720200 xHCI host does not.
Unfortunately, Harald found that the combination of the NEC µPD720200 and
a LogiLink USB 3.0 to SATA adapter triggered this issue. The USB core
would reset the device, the port would go into this error state, and the
device would never be enumerated. This combination works under Windows,
but not under Linux.
When a hot reset fails on a USB 3.0 port, and the link state is reported
as Inactive, fall back to a warm port reset instead. Harald confirms that
with a warm port reset (along with all the change bits being correctly
cleared), the USB 3.0 device will successfully enumerate.
Harald also had to add two other patches ("xhci: Set change bit when warm
reset change is set." and "usbcore: refine warm reset logic") to make this
setup work. Since the warm reset refinement patch is not destined for the
stable kernels (it's too big), this patch should not be backported either.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=41752
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Harald Brennich <harald.brennich@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current waiting time for warm(BH) reset in hub_port_warm_reset() is too short
for xHC host to complete the warm reset and report a BH reset change.
This patch increases the waiting time for warm reset and merges the function
into hub_port_reset(), so it can handle both cold reset and warm reset, and
factor out hub_port_finish_reset() to make the code looks cleaner.
This fixes the issue that driver fails to clear BH reset change and port is
"dead".
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new runtime PM code has shown that many webcams suffer
from a race condition that may crash them upon resume.
Runtime PM is especially prone to show the problem because
it retains power to the cameras at all times. However
system suspension may also crash the devices and retain
power to the devices.
The only way to solve this problem without races is in
usbcore with the RESET_RESUME quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In a few places in the kernel, the code prints
a human-readable USB device speed (eg. "high speed").
This involves a switch statement sometimes wrapped
around in ({ ... }) block leading to code repetition.
To mitigate this issue, this commit introduces
usb_speed_string() function, which returns
a human-readable name of provided speed.
It also changes a few places switch was used to use
this new function. This changes a bit the way the
speed is printed in few instances at the same time
standardising it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call. Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller. The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented. Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: James Wylder <james.wylder@motorola.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In drivers/usb/core/hub.c::usb_disconnect(), 'udev' will never be
NULL, so remove the test and printing of debug message.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event. Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
usb_ifnum_to_if() can return NULL if the USB device does not have a
configuration installed (usb_device->actconfig == NULL), or if we can't
find the interface number in the installed configuration. Return an
error instead of crashing.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
wMaxPacketSize is __le16 and should be accessed as such. Also fix the
wBytesPerInterval assignment while here.
v2: also fix the wBytesPerInterval assigment, noticed by Matt Evans
This patch should be backported to the 3.0 kernel.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Matt Evans <matt@ozlabs.org>
Cc: stable@kernel.org
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
Commit e534c5b831 (USB: fix regression
occurring during device removal) didn't go far enough. It failed to
take into account that when a driver claims multiple interfaces, it may
release them all at the same time. As a result, some interfaces can
get released before they are unregistered, and we deadlock trying to
acquire the bandwidth_mutex that we already own.
This patch (asl478) handles this case by setting the "unregistering"
flag on all the interfaces before removing any of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
