Insert PCI root bus resources for the FRV-based MB93090 development kit
motherboard. This is required because the CPU's window onto the PCI bus
address space is considerably smaller than the CPU's full address space
and non-PCI devices lie outside of the PCI window that we might want to
access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks PCI_NUM_RESOURCES (11), not 6, resources
- skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
- skips ROM resources unless IORESOURCE_ROM_ENABLE is set
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function was obviously never being used since early 2.5 days as any
device that it would try to remove would never really be removed from
the system due to the PCI device list being held in the driver core, not
the general list of PCI devices.
As we have not had a single report of a problem here in 4 years, I think
it's safe to remove now.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enable the MB93090 motherboard's MB86943 PCI arbiter correctly by assigning to
the register rather than comparing against it. This is required to support
bus mastering.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So I think the right solution is to simply make pci_enable_device just
flip enable bits and move the rest of the work someplace else.
However a thorough cleanup is a little extreme for this point in the
release cycle, so I think a quick hack that makes the code not stomp the
irq when msi irq's are enabled should be the first fix. Then we can
later make the code not change the irqs at all.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix some FRV arch compile errors, including:
(*) Marking nr_kernel_pages as __meminitdata so that references to it end up
being properly calculated rather than being assumed to be in the small
data section (and thus calculated wrt the GP register). Not doing this
causes the linker to emit errors as the offset is too big to fit into the
load instruction.
(*) Move pm_power_off into an unconditionally compiled .c file as it's now
unconditionally accessed.
(*) Declare frv_change_cmode() in a header file rather than in a .c file, and
declare it asmlinkage.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
