This fixes TRANSPARENT_HUGEPAGE=y with PARAVIRT=y and HIGHMEM64=n.
The #ifdef that this patch removes was erratically introduced to fix a
build error for noPAE (where pmd.pmd doesn't exist). So then the kernel
built but it failed at runtime because set_pmd_at was a noop. This will
correct it by enabling set_pmd_at for noPAE mode too.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: werner <w.landgraf@ru.ru>
Reported-by: Minchan Kim <minchan.kim@gmail.com>
Tested-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix build of sh7750 base boards
sh: update INTC to clear IRQ sense valid flag
sh: Fix sh build failure when CONFIG_SFC=m
sh: fix MSIOF0 SPI on ecovec: it conflicts with VOU
sh: support XZ-compressed kernel.
sh: Fix up breakage from asm-generic/pgtable.h changes.
The EP93xx C and D GPIO ports are multiplexed with the Keypad Interface
peripheral. At power-up they default into non-GPIO mode with the Key
Matrix controller enabled so these ports are unusable for GPIO. Note
that the Keypad Interface peripheral is only available in the EP9307,
EP9312, and EP9315 processor variants.
The keypad support will clear the DeviceConfig bits appropriately to
enable the Keypad Interface when the driver is loaded. And, when the
driver is unloaded it will set the bits to return the ports to GPIO mode.
To make these ports available for GPIO after power-up on all EP93xx
processor variants, set the KEYS and GONK bits in the DeviceConfig
register.
Similarly, the E, G, and H ports are multiplexed with the IDE Interface
peripheral. At power-up these also default into non-GPIO mode. Note
that the IDE peripheral is only available in the EP9312 and EP9315
processor variants.
Since an IDE driver is not even available in mainline, set the EONIDE,
GONIDE, and HONIDE bits in the DeviceConfig register so that these
ports will be available for GPIO use after power-up.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changing the virt_to_phys() argument to "const volatile void *" avoids
compiler warnings in some situations where this function is used.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the twd timer reload value is reprogrammed each time we
enter periodic mode. This ensures that the reload value is always
reset correctly.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the option text to those which appear on the front of the
appropriate board user guides. This gives consistent board naming, and
makes it obvious which option is for which platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As no one seems to really know which configuration options tie up with
which boards, I thought I'd do some investigation and try to work it
out. After discussion with some folk in linaro, I think I have this
nailed.
The names are updated to use the name on the front of the appropriate
board user guide for the various baseboards, which I've taken to be
the official name for each board.
I haven't significantly updated the descriptions for the tiles as that
is even less clear - as far as I can see on ARMs website, there is no
Cortex-A9 tile for Realview EB - only ARM11MPCore, ARM1156T2F-S,
ARM1176TZF-S and Cortex-R4F. So exactly what this 'Multicore Cortex-A9
Tile' is...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two section mismatch warnings in the platform SMP bringup code for
Realview and Versatile Express:
WARNING: arch/arm/mach-realview/built-in.o(.text+0x8ac): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
WARNING: arch/arm/mach-vexpress/built-in.o(.text+0x7b4): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: DMA: clear interrupt status correctly
OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration
arm: omap3: cm-t3517: minor comment fix
arm: omap3: cm-t3517: rtc fix
omap1: Fix sched_clock implementation when both MPU timer and 32K timer are used
omap1: Fix booting for 15xx and 730 with omap1_defconfig
omap1: Fix sched_clock for the MPU timer
OMAP: PRCM: remove duplicated headers
OMAP4: clockdomain: bypass unimplemented wake-up dependency functions on OMAP4
OMAP: counter_32k: init clocksource as part of machine timer init
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix time function double declaration with glibc
perf tools: Fix build by checking if extra warnings are supported
perf tools: Fix build when using gcc 3.4.6
perf tools: Add missing header, fixes build
perf tools: Fix 64 bit integer format strings
perf test: Fix build on older glibcs
perf: perf_event_exit_task_context: s/rcu_dereference/rcu_dereference_raw/
perf test: Use cpu_map->[cpu] when setting affinity
perf symbols: Fix annotation of thumb code
perf: Annotate cpuctx->ctx.mutex to avoid a lockdep splat
powerpc, perf: Fix frequency calculation for overflowing counters (FSL version)
perf: Fix perf_event_init_task()/perf_event_free_task() interaction
perf: Fix find_get_context() vs perf_event_exit_task() race
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix jump label with RO/NX module protection crash
x86, hotplug: Fix powersavings with offlined cores on AMD
x86, mcheck, therm_throt.c: Export symbol platform_thermal_notify to allow coretemp to handler intr
x86: Use asm-generic/cacheflush.h
x86: Update CPU cache attributes table descriptors
If we use jump table in module init, there are marked
as removed in __jump_table section after init is done.
But we already applied ro permissions on the module, so
we can't modify a read only section (crash in
remove_jump_label_module_init).
Make the __jump_table section rw.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Siarhei Liakh <sliakh.lkml@gmail.com>
Cc: Xuxian Jiang <jiang@cs.ncsu.edu>
Cc: James Morris <jmorris@namei.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Cc: Kees Cook <kees.cook@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4D3C3F20.7030203@free.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
`debug=mem' on Amiga has been broken for a while.
early_param() processing is done very/too early, i.e. before
amiga_identify() / amiga_chip_init(), causing amiga_savekmsg_setup() not
to find any Chip RAM.
As we don't plan to free this memory anyway, just steal it from the initial
Chip RAM memory block instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It's a way too generic name for a global #define and conflicts with a variable
with the same name, causing build errors like:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c: In function ‘_si_clkctl_cc’:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected identifier or ‘(’ before ‘volatile’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected ‘)’ before ‘(’ token
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1421: error: incompatible types in assignment
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1422: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1423: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1424: error: invalid operands to binary |
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: incompatible type for argument 4 of ‘bcmsdh_reg_write’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1428: error: invalid operands to binary &
| make[8]: *** [drivers/staging/brcm80211/brcmfmac/../util/siutils.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Some versions of gcc replace calls to strstr() with single-character
"needle" string parameters by calls to strchr() behind our back.
If strchr() is defined as an inline function, this causes linking errors
like
ERROR: "strchr" [drivers/target/target_core_mod.ko] undefined!
As m68k is the only architecture that has an inline strchr() and this
inline version is not an optimized asm version, uninline strchr() and use
the standard out-of-line C version in lib/string.c instead.
This also decreases the defconfig/allmodconfig kernel image sizes by a few
hundred bytes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
ea53069231 made a CPU use monitor/mwait
when offline. This is not the optimal choice for AMD wrt to powersavings
and we'd prefer our cores to halt (i.e. enter C1) instead. For this, the
same selection whether to use monitor/mwait has to be used as when we
select the idle routine for the machine.
With this patch, offlining cores 1-5 on a X6 machine allows core0 to
boost again.
[ hpa: putting this in urgent since it is a (power) regression fix ]
Reported-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org # 37.x
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.hl>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1295534572-10730-1-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
After changing the p2m mapping to a tree by
commit 58e05027b5
xen: convert p2m to a 3 level tree
and trying to boot a DomU with 615MB of memory, the following crash was
observed in the dump:
kernel direct mapping tables up to 26f00000 @ 1ec4000-1fff000
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c0107397>] xen_set_pte+0x27/0x60
*pdpt = 0000000000000000 *pde = 0000000000000000
Adding further debug statements showed that when trying to set up
pfn=0x26700 the returned mapping was invalid.
pfn=0x266ff calling set_pte(0xc1fe77f8, 0x6b3003)
pfn=0x26700 calling set_pte(0xc1fe7800, 0x3)
Although the last_pfn obtained from the startup info is 0x26700, which
should in turn not be hit, the additional 8MB which are added as extra
memory normally seem to be ok. This lead to looking into the initial
p2m tree construction, which uses the smaller value and assuming that
there is other code handling the extra memory.
When the p2m tree is set up, the leaves are directly pointed to the
array which the domain builder set up. But if the mapping is not on a
boundary that fits into one p2m page, this will result in the last leaf
being only partially valid. And as the invalid entries are not
initialized in that case, things go badly wrong.
I am trying to fix that by checking whether the current leaf is a
complete map and if not, allocate a completely new page and copy only
the valid pointers there. This may not be the most efficient or elegant
solution, but at least it seems to allow me booting DomUs with memory
assignments all over the range.
BugLink: http://bugs.launchpad.net/bugs/686692
[v2: Redid a bit of commit wording and fixed a compile warning]
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In therm_throt.c, commit
9e76a97efd patch doesn't export
the symbol platform_thermal_notify.
Other drivers (e.g. drivers/hwmon/coretemp.c) can not find the
symbol platform_thermal_notify when defining threshould
interrupt handler.
Please apply this patch to allow threshold interrupt handler in
coretemp.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: R Durgadoss <durgadoss.r@intel.com>
Cc: khali@linux-fr.org <khali@linux-fr.org>
Cc: lm-sensors@lm-sensors.org <lm-sensors@lm-sensors.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
LKML-Reference: <20110121041239.GB26954@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The implementation of the cache flushing interfaces on the x86
is identical with the default implementation in asm-generic.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: arnd@arndb.de
LKML-Reference: <1295523136-4277-2-git-send-email-akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Dike <jdike@addtoit.com>
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Use the generic irq Kconfig. Select GENERIC_HARDIRQS_NO_DEPRECATED as
we have converted all irq_chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
