When waiting for high frequency requests, the finite amount of time
required to set up the irq and wait upon it limits the response rate. By
busywaiting on the request completion for a short while we can service
the high frequency waits as quick as possible. However, if it is a slow
request, we want to sleep as quickly as possible. The tradeoff between
waiting and sleeping is roughly the time it takes to sleep on a request,
on the order of a microsecond. Based on measurements of synchronous
workloads from across big core and little atom, I have set the limit for
busywaiting as 10 microseconds. In most of the synchronous cases, we can
reduce the limit down to as little as 2 miscroseconds, but that leaves
quite a few test cases regressing by factors of 3 and more.
The code currently uses the jiffie clock, but that is far too coarse (on
the order of 10 milliseconds) and results in poor interactivity as the
CPU ends up being hogged by slow requests. To get microsecond resolution
we need to use a high resolution timer. The cheapest of which is polling
local_clock(), but that is only valid on the same CPU. If we switch CPUs
because the task was preempted, we can also use that as an indicator that
the system is too busy to waste cycles on spinning and we should sleep
instead.
__i915_spin_request was introduced in
commit 2def4ad99b [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe,
so we can use native register sizes on smaller architectures. Mention
the approximate microseconds units for elapsed time and add some extra
comments describing the reason for busywaiting.
v3: Raise the limit to 10us
v4: Now 5us.
Reported-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.org/lkml/2015/11/12/621
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit ca5b721e23)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The busywait in __i915_spin_request() does not respect pending signals
and so may consume the entire timeslice for the task instead of
returning to userspace to handle the signal.
In the worst case this could cause a delay in signal processing of 20ms,
which would be a noticeable jitter in cursor tracking. If a higher
resolution signal was being used, for example to provide fairness of a
server timeslices between clients, we could expect to detect some
unfairness between clients (i.e. some windows not updating as fast as
others). This issue was noticed when inspecting a report of poor
interactivity resulting from excessively high __i915_spin_request usage.
Fixes regression from
commit 2def4ad99b [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Try to assess the impact of the bug
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc; "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-2-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 91b0c352ac)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If we fail to reconstruct the BIOS fb (e.g., because the FB is too
large), we'll be left with plane state that indicates the primary plane
is visible yet has a NULL fb. This mismatch causes problems later on
(e.g., for the watermark code). Since we've failed to reconstruct the
BIOS FB, the best solution is to just disable the primary plane and
pretend the BIOS never had it enabled.
v2: Add intel_pre_disable_primary() call (Maarten)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449171462-30763-2-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit 200757f5d7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As we mark the preallocated objects as bound, we should also flag them
correctly as being map-and-fenceable (if appropriate!) so that later
users do not get confused and try and rebind the pinned vma in order to
get a map-and-fenceable binding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1448029000-10616-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit d0710abbcd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The cursor code tries to treat base==0 to mean disabled. That fails
when the cursor bo gets bound at ggtt offset 0, and the user is left
looking at an invisible cursor.
We lose the disabled->disabled optimization, but that seems like
something better handled at a slightly higher level.
Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450091808-32607-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 663f3122d0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When disable_noatomic is called plane_mask is not correct yet, and
plane_state->visible = true is left as true after disabling the primary
plane.
Other planes are already disabled as part of crtc sanitization, only the
primary is left active. But the plane_mask is not updated here. It gets
updated during fb takeover in modeset_gem_init, or set to the new value
on resume.
This means that to disable the primary plane 1 << drm_plane_index(primary)
needs to be used.
Afterwards because the crtc is no longer active it's forbidden to keep
plane_state->visible set, or a WARN_ON in
intel_plane_atomic_calc_changes triggers. There are other code points
that rely on accurate plane_state->visible too, so make sure the bool is
cleared.
The other planes are already disabled in intel_sanitize_crtc, so they
don't have to be handled here.
Cc: stable@vger.kernel.org #v4.3, v4.2?
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92655
Tested-by: Tomas Mezzadra <tmezzadra@gmail.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/5652DB88.9070208@linux.intel.com
(cherry picked from commit 54a4196188)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There is conflicting info between E0 and F0 steppings
for this workarounds. Trust more authoritative source and
be conservative and extend also for F0.
This prevents numerous (>50) gpu hangs with SKL GT4e
during piglit run.
References: HSD: gen9lp/2134184
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449505785-20812-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 6686ece19f)
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit e9f24d5fb7
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Mon Oct 5 13:26:36 2015 +0100
drm/i915: Clean up associated VMAs on context destruction
Added a warning based on an incorrect assumption that all VMAs
in a VM will be on the inactive list at the point last reference
to a context and VM is dropped.
This is not true because i915_gem_object_retire__read will not
put VMA on the inactive list until all activities on the object
in question (in all VMs) have been retired.
As a consequence, whether or not a context/VM will be destroyed
with its VMAs still on the active list, can depend on completely
unrelated activities using the same object from a different
context or engine.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92638
Testcase: igt/gem_request_retire/retire-vma-not-inactive
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448025816-25584-1-git-send-email-tvrtko.ursulin@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 408952d43b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are platforms that don't need the full GMBUS power domain (BXT)
while others do (PCH, VLV/CHV). For optimizing this we would need to add
a new power domain, but it's not clear how much we would benefit given
the short time we hold the reference. So for now let's keep things
simple.
This fixes a regression introduced in
commit 237ed86c69
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Tue Sep 15 09:44:20 2015 +0530
drm/i915: Check live status before reading edid
v2:
- fix commit message, PCH won't take any redundant power resource after
this change (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[fix commit message in v2 (Imre)]
[Cherry-picked from drm-intel-next-queued 29bb94bb (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-6-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MISSING_CASE() would have been useful to track down a recent problem in
intel_display_port_aux_power_domain(), so add it there and a few related
helpers. This was also suggested by Ville in his review of the latest
DMC/DC changes, we forgot to address that.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued b9fec167 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-5-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Due to the current sharing of the DDI encoder between DP and HDMI
connectors we can run the DP detection after the HDMI detection has
already set the shared encoder's type. For now solve this keeping the
current behavior and running the detection in this case too. For a proper
solution Ville suggested to split the encoder into an HDMI and DP one, that
can be done as a follow-up.
This issue triggers the WARN in intel_display_port_aux_power_domain() and
was introduced in:
commit 25f78f58e5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Nov 16 15:01:04 2015 +0100
drm/i915: Clean up AUX power domain handling
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 651174a4 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-4-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued f0ab43e6 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-3-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 25f78f58 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-2-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We have relied upon the sole caller (wait_ioctl) validating the timeout
argument. However, when waiting for multiple requests I forgot to ensure
that the timeout was still positive on the later requests. This is more
simply done inside __i915_wait_request.
Fixes regression introduced in
commit b47161858b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 27 13:41:17 2015 +0100
drm/i915: Implement inter-engine read-read optimisations
The impact of the regression is 1 jiffie for each extra active ring for
a wait_ioctl with a timeout -- I don't think anyone has noticed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448544702-5594-1-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently a DDI port may register the DP hotplug handler even though
it's used with HDMI, and the DP HPD handler overrides the encoder
type forcibly to DP. This caused the inconsistency on a machine
connected with a HDMI monitor; upon a hotplug event, the DDI port is
suddenly switched to be handled as a DP although the same monitor is
kept connected, and this leads to the erroneous blank output.
This patch papers over the bug by excluding the previous HDMI encoder
type from this override. This should be fixed more fundamentally,
e.g. by moving the encoder type reset from the HPD or by having
individual encoder objects for HDMI and DP. But since the bug has
been present for a long time (3.17), it's better to have a
quick-n-dirty fix for now, and keep working on a cleaner fix.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=955190
Fixes: 0e32b39cee ('drm/i915: add DP 1.2 MST support (v0.7)')
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447931396-19147-1-git-send-email-tiwai@suse.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The commit [cfb23ed622: drm/i915: Allow fuzzy matching in
pipe_config_compare, v2] relaxed the way to compare the pipe
configurations, but one new comparison sneaked in there: it added the
strict has_drrs value check. This causes a regression on many
machines, typically HP laptops with a docking port, where the kernel
spews warnings and eventually fails to set the mode properly like:
[drm:intel_pipe_config_compare [i915]] *ERROR* mismatch in has_drrs (expected 1, found 0)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 79 at drivers/gpu/drm/i915/intel_display.c:12700 intel_modeset_check_state+0x5aa/0x870 [i915]()
pipe state doesn't match!
....
This patch just removes the check again for fixing the regression.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=104041
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92456
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=956397
Fixes: cfb23ed622 ('drm/i915: Allow fuzzy matching in pipe_config_compare, v2')
Cc: <stable@vger.kernel.org> # v4.3+
Reported-and-tested-by: Max Lin <mlin@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448461607-16868-1-git-send-email-tiwai@suse.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We have varied reports of swizzling corruption on gen4 desktop, and
confirmation that one at least is triggered by uneven memory banks
(L-shaped memory). The implication is that the swizzling varies between
the paired channels and the remainder of memory on the single channel. As
the object then has unpredictable swizzling (it will vary depending on
exact page allocation and may even change during the object's lifetime as
the pages are replaced), we have to report to userspace that the swizzling
is unknown.
However, some existing userspace is buggy when it meets an unknown
swizzling configuration and so we need to tell another white lie and
mark the swizzling as NONE but report it as UNKNOWN through the extended
get-tiling-ioctl. See
commit 5eb3e5a5e1
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Jun 28 09:19:26 2015 +0100
drm/i915: Declare the swizzling unknown for L-shaped configurations
for the previous example where we found that telling the truth to
userspace just ends up in a world of hurt.
Also since we don't truly know what the swizzling is on the pages, we
need to keep them pinned to prevent swapping as the reports also
suggest that some gen4 devices have previously undetected bit17
swizzling.
v2: Combine unknown + quirk patches to prevent userspace ever seeing
unknown swizzling through the normal get-tiling-ioctl. Also use the same
path for the existing uneven bank detection for mobile gen4.
Reported-by: Matti Hämäläinen <ccr@tnsp.org>
Tested-by: Matti Hämäläinen <ccr@tnsp.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matti Hämäläinen <ccr@tnsp.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1447927085-31726-1-git-send-email-chris@chris-wilson.co.uk
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts
commit 6764e9f872
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Thu Aug 27 15:44:06 2015 +0200
drm/i915: skip modeset if compatible for everyone.
Bring back the i915.fastboot module parameter, disabled by default, due
to backlight regression on Chromebook Pixel 2015.
Apparently the firmware of the Chromebook in question enables the panel
but disables backlight to avoid a brief garbage scanout upon loading the
kernel/module. With fastboot, we leave the backlight untouched, in this
case disabled. The user would have to do a modeset (i.e. not just crank
up the brightness) to enable the backlight.
There is no clean fix readily available, so get back to the drawing
board by reverting.
[N.B. The reference below is for when the thread was included on public
lists, and some of the context had already been dropped by then.]
Reported-and-tested-by: Olof Johansson <olof@lixom.net>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: http://marc.info/?i=CAKMK7uES7xk05ki92oeX6gmvZWAh9f2vL7yz=6T+fGK9J3X7cQ@mail.gmail.com
Fixes: 6764e9f872 ("drm/i915: skip modeset if compatible for everyone.")
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447921590-3785-1-git-send-email-jani.nikula@intel.com
When diagnosing a unrelated bug for someone on irc, it would seem the hardware can
be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.
Right now this is not handled well in i915, and it calculates the crtc needs to
be reprogrammed on the first modeset without SSC, but the SPLL itself was kept
active. Fix this by exposing SPLL as a shared pll that will not be returned
by intel_get_shared_dpll; you have to know it exists to use it.
Changes since v1:
- Create a separate dpll_hw_state.spll for spll, and use
separate pll functions for spll.
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Gabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With gen < 9 we have had always 50Mhz units as our hw
ratio. With gen >= 9 the hw ratio changed to 16.667Mhz (50/3).
The result was that our gpu frequency tracing started to output
values 3 times larger than expected due to hardcoded scaling
value. Fix this by using Use intel_gpu_freq() when generating Mhz
value from ratio for 'intel_gpu_freq_change' trace event.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92591
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447776866-29384-1-git-send-email-mika.kuoppala@intel.com
We try to convert the old way of of specifying fb tiling (obj->tiling)
into the new fb modifiers. We store the result in the passed in mode_cmd
structure. But that structure comes directly from the addfb2 ioctl, and
gets copied back out to userspace, which means we're clobbering the
modifiers that the user provided (all 0 since the DRM_MODE_FB_MODIFIERS
flag wasn't even set by the user). Hence if the user reuses the struct
for another addfb2, the ioctl will be rejected since it's now asking for
some modifiers w/o the flag set.
Fix the problem by making a copy of the user provided structure. We can
play any games we want with the copy.
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
...
Subtest basic-X-tiled: SUCCESS (0.001s)
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
Stack trace:
#0 [__igt_fail_assert+0x101]
#1 [pitch_tests+0x619]
#2 [__real_main426+0x2f]
#3 [main+0x23]
#4 [__libc_start_main+0xf0]
#5 [_start+0x29]
#6 [<unknown>+0x29]
Subtest framebuffer-vs-set-tiling failed.
**** DEBUG ****
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
**** END ****
Subtest framebuffer-vs-set-tiling: FAIL (0.003s)
...
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
Subtest framebuffer-vs-set-tiling: SUCCESS (0.000s)
Cc: stable@vger.kernel.org # v4.1+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 2a80eada32 ("drm/i915: Add fb format modifier support")
Testcase: igt/kms_addfb_basic/clobbered-modifier
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447261890-3960-1-git-send-email-ville.syrjala@linux.intel.com
After Damien's D3 fix I started to get runtime suspend residency for the
first time and that revealed a breakage on the set_caching IOCTL path
that accesses the HW but doesn't take an RPM ref. Fix this up.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1446665132-22491-1-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we set and later readback a frequency value through
sysfs interface, igt/pm_rpm assumes that we get same value back
if it matches hw granularity.
On bxt we have found out that this is not always the case.
Currently frequency - hw ratio - frequency conversions round down,
with few exceptions on platforms that have more specific conversions.
On bxt the supported range can be for example from 100Mhz to 650Mhz.
Midpoint is then calculated by test to be 375 which pm_rps uses to find a
closest hw supported frequency. That is 366 (ratio 22),
which it then writes back. But as the rounding down kicks in,
driver actually sets 350 instead of 366, as 366 is 2/3 below 22 * 50/3.
Fix this by rounding to closest instead of rounding down in
freq-ratio-freq conversions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92768
Testcase: igt/pm_rps/basic-api
Tested-by: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447435781-23416-1-git-send-email-mika.kuoppala@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Let's set crtc_y to 0 instead of setting src_y twice.
Multiple assignments in one statement is a good way to hide bugs.
Please don't do that.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: be5651f2d5 ("drm/i915: Update missing properties in find_initial_plane_obj")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447434973-12369-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Pull drm updates from Dave Airlie:
"I Was Almost Tempted To Capitalise Every Word, but then I decided I
couldn't read it myself!
I've also got one pull request for the sti driver outstanding. It
relied on a commit in Greg's tree and I didn't find out in time, that
commit is in your tree now so I might send that along once this is
merged.
I also had the accidental misfortune to have access to a Skylake on my
desk for a few days, and I've had to encourage Intel to try harder,
which seems to be happening now.
Here is the main drm-next pull request for 4.4.
Highlights:
New driver:
vc4 driver for the Rasberry Pi VPU.
(From Eric Anholt at Broadcom.)
Core:
Atomic fbdev support
Atomic helpers for runtime pm
dp/aux i2c STATUS_UPDATE handling
struct_mutex usage cleanups.
Generic of probing support.
Documentation:
Kerneldoc for VGA switcheroo code.
Rename to gpu instead of drm to reflect scope.
i915:
Skylake GuC firmware fixes
HPD A support
VBT backlight fallbacks
Fastboot by default for some systems
FBC work
BXT/SKL workarounds
Skylake deeper sleep state fixes
amdgpu:
Enable GPU scheduler by default
New atombios opcodes
GPUVM debugging options
Stoney support.
Fencing cleanups.
radeon:
More efficient CS checking
nouveau:
gk20a instance memory handling improvements.
Improved PGOB detection and GK107 support
Kepler GDDR5 PLL statbility improvement
G8x/GT2xx reclock improvements
new userspace API compatiblity fixes.
virtio-gpu:
Add 3D support - qemu 2.5 has it merged for it's gtk backend.
msm:
Initial msm88896 (snapdragon 8200)
exynos:
HDMI cleanups
Enable mixer driver byt default
Add DECON-TV support
vmwgfx:
Move to using memremap + fixes.
rcar-du:
Add support for R8A7793/4 DU
armada:
Remove support for non-component mode
Improved plane handling
Power savings while in DPMS off.
tda998x:
Remove unused slave encoder support
Use more HDMI helpers
Fix EDID read handling
dwhdmi:
Interlace video mode support for ipu-v3/dw_hdmi
Hotplug state fixes
Audio driver integration
imx:
More color formats support.
tegra:
Minor fixes/improvements"
[ Merge fixup: remove unused variable 'dev' that had all uses removed in
commit 4e270f0880: "drm/gem: Drop struct_mutex requirement from
drm_gem_mmap_obj" ]
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits)
drm/vmwgfx: Relax irq locking somewhat
drm/vmwgfx: Properly flush cursor updates and page-flips
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT
drm/amdgpu: group together common fence implementation
drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE
drm/amdgpu: remove now unused fence functions
drm/amdgpu: fix fence fallback check
drm/amdgpu: fix stoping the scheduler timeout
drm/amdgpu: cleanup on error in amdgpu_cs_ioctl()
drm/i915: Fix locking around GuC firmware load
drm/amdgpu: update Fiji's Golden setting
drm/amdgpu: update Fiji's rev id
drm/amdgpu: extract common code in vi_common_early_init
drm/amd/scheduler: don't oops on failure to load
drm/amdgpu: don't oops on failure to load (v2)
drm/amdgpu: don't VT switch on suspend
...
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
Here's a handful of i915 fixes for drm-next/v4.4. Imre's commit alone
should address the remaining warnings galore you experienced on
Skylake. Almost all of the rest are also fixes against user or QA
reported bugs, with references.
* tag 'drm-intel-next-fixes-2015-11-06' of git://anongit.freedesktop.org/drm-intel:
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
drm/i915: add quirk to enable backlight on Dell Chromebook 11 (2015)
drm/i915/skl: Prevent unclaimed register writes on skylake.
drm/i915: disable CPU PWM also on LPT/SPT backlight disable
drm/i915: Fix maxfifo watermark calc on vlv cursor planes
drm/i915: add hotplug activation period to hotplug update mask
There are many places which use mapping_gfp_mask to restrict a more
generic gfp mask which would be used for allocations which are not
directly related to the page cache but they are performed in the same
context.
Let's introduce a helper function which makes the restriction explicit and
easier to track. This patch doesn't introduce any functional changes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT was used to signal that the caller was in atomic context and
could not sleep. Now it is possible to distinguish between true atomic
context and callers that are not willing to sleep. The latter should
clear __GFP_DIRECT_RECLAIM so kswapd will still wake. As clearing
__GFP_WAIT behaves differently, there is a risk that people will clear the
wrong flags. This patch renames __GFP_WAIT to __GFP_RECLAIM to clearly
indicate what it does -- setting it allows all reclaim activity, clearing
them prevents it.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The display power well support on this platform is in a somewhat broken
state atm, so disable it by default.
This in effect will get rid of incorrect assert WARNs about the CSR/DMC
firmware not being loaded during power well toggling. It also removes a
problem during driver loading where a register is accessed while its
backing power well is down, resulting in another WARN. Until we come up
with the root cause of the second problem and the proper fix for both
issues, keep all display side power wells on.
Also clarify a bit the option description.
Reported-by: Dave Airlie <airlied@redhat.com>
Reference: http://mid.gmane.org/CAPM=9tyjBQjSBTKa49cRr6SYkpNW7Pq-fUFznZZ8Y1snvvk7mA@mail.gmail.com
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446757451-2777-1-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We have a timed release of a forcewake when using
I915_READ/WRITE macros. wait_for() macro will go to quite
long sleep if the first read doesn't satisfy the condition for
successful exit. With these two interacting, it is possible that
we lose the forcewake during the wait_for() and the subsequent read
will reaquire forcewake.
Further experiments with skl shows that when we lose forcewake,
we lose the reset request we submitted. So reset request register
is not power context saved.
Grab forcewakes for all engines before starting the reset/request
dance so that all requests stay valid for the duration of reset
requisition across all the engines.
v2: Add comment on power well sleeps. Wrap the reset handling
under forcewake instead of just reset requests (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92774
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomi Sarvela <tomix.p.sarvela@intel.com> (v1, v2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446721898-1450-1-git-send-email-mika.kuoppala@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While pinning a fb object to the display plane, only install a fence
if the object is using a normal view. This corresponds with the
behavior found in i915_gem_object_do_pin() where the fencability
criteria is determined only for objects with normal views.
v2:
Look at the object's map_and_fenceable flag to determine whether to
install a fence or not (Chris).
v3:
Pin and unpin a fence only if the current view type is normal.
v4:
Extend the "view type is normal" check for pin_fence as well.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446170078-20792-1-git-send-email-vivek.kasireddy@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I'm getting unclaimed register writes when checking the WM registers
after the crtc is disabled. So I would imagine those are guarded by
the crtc power well. Fix this by not reading out wm state when the
power well is off.
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bunch of -fixes for 4.4. Well not just, I've left the mmio/register work
from Ville in here since it's low-risk but lots of churn all over.
* tag 'drm-intel-next-fixes-2015-10-22' of git://anongit.freedesktop.org/drm-intel: (23 commits)
drm/i915: Use round to closest when computing the CEA 1.001 pixel clocks
drm/i915: Kill the leftover RMW from ivb_sprite_disable()
drm/i915: restore ggtt double-bind avoidance
drm/i915/skl: Enable pipe gamma for sprite planes.
drm/i915/skl+: Enable pipe CSC on cursor planes. (v2)
MAINTAINERS: add link to the Intel Graphics for Linux web site
drm/i915: Move skl/bxt gt specific workarounds to ring init
drm/i915: Drop i915_gem_obj_is_pinned() from set-cache-level
drm/i915: revert a few more watermark commits
drm/i915: Remove dev_priv argument from NEEDS_FORCE_WAKE
drm/i915: Clean up LVDS register handling
drm/i915: Throw out some useless variables
drm/i915: Parametrize and fix SWF registers
drm/i915: s/PIPE_FRMCOUNT_GM45/PIPE_FRMCOUNT_G4X/ etc.
drm/i915: Turn GEN5_ASSERT_IIR_IS_ZERO() into a function
drm/i915: Fix a few bad hex numbers in register defines
drm/i915: Protect register macro arguments
drm/i915: Include gpio_mmio_base in GMBUS reg defines
drm/i915: Parametrize HSW video DIP data registers
drm/i915: Eliminate weird parameter inversion from BXT PPS registers
...
Although we don't support or enable CPU PWM with LPT/SPT based systems,
it may have been enabled prior to loading the driver. Disable the CPU
PWM on LPT/SPT backlight disable to avoid warnings on LCPLL disable.
The issue has been present on BDW since BDW enabling, but was recently
introduced on HSW with
commit 437b15b801
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 4 16:55:13 2015 +0300
drm/i915: use pch backlight override on hsw too
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reference: http://mid.gmane.org/87y4frhwsn.fsf@yhuang-dev.intel.com
Reported-by: kernel test robot <ying.huang@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446033429-8006-1-git-send-email-jani.nikula@intel.com
A typo resulted in the watermarks for cursor planes not being calculated
correctly. Fixed the typo.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWLbbGAAoJECTWi3JdVIfQH7oH/1VdN2ozP9A03p24aC5qso1F
VWOBnG4pkw1G6J5qK2lemMDeJdRdTfreICUAa9Tw9kOSfTIb6F3X8kCw8tbwlw0I
4phgmyo23P53OfLZFMkQi/RCfwItnE0sszqhvoumUg0ryjYxg2JT+gTMgwvVo7Pq
hf6m6a3we5pxLIIYP4wlQgOKwUJe4B4nC37ExySf24Dlo/DzmWDtfQbGvmyluFzb
MB1qzEvAc/KC3LZFkIFmhfg2/caNRhcQrzkUCYrLR3t+oz9P1zCpYTII7VDdMg7L
SM2VoL+ynEAdBqa38Ozwxvd/mpHwinlAeiikuwz1PyxVOqZvZqqiWzD8eUJkhZk=
=/F/Q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
- A new driver for the Atmel Class D speaker drivers
commit 0706f17c30
Author: Egbert Eich <eich@suse.de>
Date: Wed Sep 23 16:15:27 2015 +0200
drm/i915: Avoid race of intel_crt_detect_hotplug() with HPD interrupt, v2
added a check with WARN to ensure only bits within the mask are
enabled. Turns out that doesn't hold for G4X, which spits out:
[ 2.641439] ------------[ cut here ]------------
[ 2.641444] WARNING: CPU: 0 PID: 1 at drivers/gpu/drm/i915/i915_irq.c:182 i915_hotplug_interrupt_update_locked+0x45/0x83()
[ 2.641446] WARN_ON(bits & ~mask)
etc.
Add CRT_HOTPLUG_ACTIVATION_PERIOD_64 to the mask to fix the warning.
Reported-and-tested-by: Oleksij Rempel <linux@rempel-privat.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=104991
Fixes: 0706f17c30 ("drm/i915: Avoid race of intel_crt_detect_hotplug() with HPD interrupt, v2")
Cc: Egbert Eich <eich@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1445437363-3030-1-git-send-email-jani.nikula@intel.com
More drm-misc for 4.4.
- fb refcount fix in atomic fbdev
- various locking reworks to reduce drm_global_mutex and dev->struct_mutex
- rename docbook to gpu.tmpl and include vga_switcheroo stuff, plus more
vga_switcheroo (Lukas Wunner)
- viewport check fixes for atomic drivers from Ville
- DRM_DEBUG_VBL from Ville
- non-contentious header fixes from Mikko Rapeli
- small things all over
* tag 'topic/drm-misc-2015-10-19' of git://anongit.freedesktop.org/drm-intel: (31 commits)
drm/fb-helper: Fix fb refcounting in pan_display_atomic
drm/fb-helper: Set plane rotation directly
drm: fix mutex leak in drm_dp_get_mst_branch_device
drm: Check plane src coordinates correctly during page flip for atomic drivers
drm: Check crtc viewport correctly with rotated primary plane on atomic drivers
drm: Refactor plane src coordinate checks
drm: Swap w/h when converting the mode to src coordidates for a rotated primary plane
drm: Don't leak fb when plane crtc coodinates are bad
ALSA: hda - Spell vga_switcheroo consistently
drm/gem: Use kref_get_unless_zero for the weak mmap references
drm/vgem: Drop vgem_drm_gem_mmap
drm: Fix return value of drm_framebuffer_init()
drm/gem: Use container_of in drm_gem_object_free
drm/gem: Check locking in drm_gem_object_unreference
drm/gem: Drop struct_mutex requirement from drm_gem_mmap_obj
drm/i810_drm.h: include drm/drm.h
r128_drm.h: include drm/drm.h
savage_drm.h: include <drm/drm.h>
gpu/doc: Convert to markdown harder
gpu/doc: Add vga_switcheroo documentation
...
- dmc fixes from Animesh (not yet all) for deeper sleep states
- piles of prep patches from Ville to make mmio functions type-safe
- more fbc work from Paulo all over
- w/a shuffling from Arun Siluvery
- first part of atomic watermark updates from Matt and Ville (later parts had to
be dropped again unfortunately)
- lots of patches to prepare bxt dsi support ( Shashank Sharma)
- userptr fixes from Chris
- audio rate interface between i915/snd_hda plus kerneldoc (Libin Yang)
- shrinker improvements and fixes (Chris Wilson)
- lots and lots of small patches all over
* tag 'drm-intel-next-2015-10-10' of git://anongit.freedesktop.org/drm-intel: (134 commits)
drm/i915: Update DRIVER_DATE to 20151010
drm/i915: Partial revert of atomic watermark series
drm/i915: Early exit from semaphore_waits_for for execlist mode.
drm/i915: Remove wrong warning from i915_gem_context_clean
drm/i915: Determine the stolen memory base address on gen2
drm/i915: fix FBC buffer size checks
drm/i915: fix CFB size calculation
drm/i915: remove pre-atomic check from SKL update_primary_plane
drm/i915: don't allocate fbcon from stolen memory if it's too big
Revert "drm/i915: Call encoder hotplug for init and resume cases"
Revert "drm/i915: Add hot_plug hook for hdmi encoder"
drm/i915: use error path
drm/i915/irq: Fix misspelled word register in kernel-doc
drm/i915/irq: Fix kernel-doc warnings
drm/i915: Hook up ring workaround writes at context creation time on Gen6-7.
drm/i915: Don't warn if the workaround list is empty.
drm/i915: Resurrect golden context on gen6/7
drm/i915/chv: remove pre-production hardware workarounds
drm/i915/snb: remove pre-production hardware workaround
drm/i915/bxt: Set time interval unit to 0.833us
...
drm_edid.c now computes the alternate CEA clocks using
DIV_ROUND_CLOSEST(), so follow suit in the N/CTS setup to make sure we
pick the right setting for the mode.
Unfortunately we can't actually use DIV_ROUND_CLOSEST() here due to the
({}) construct used, so just stick in raw numbers instead.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Libin Yang <libin.yang@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just one special case (since i915 lost its ums code, yay):
- radeon: Has slots for the old ums ioctls which don't have
DRM_UNLOCKED, but all filled with drm_invalid_op. So ok to drop it
everywhere.
Every other kms driver just has DRM_UNLOCKED for all their ioctls, as
they should.
v2: admgpu happened, include that one too. And i915 lost its UMS
support which means we can change all the i915 ioctls too.
v3: Rebased on top of new vmwgfx DX interface extensions.
v4: Rebase on top of render-node support in exynos.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With kms all the data getparam looks at is actually invariant, and
certainly not protected by the global kms mutex. With ums all the
setup code is already racy as hell, so this won't make things any
worse.
I've done this change so that all ioctl still used by kms drivers
are marked as DRM_UNLOCKED, besides that we obviously don't need
it any more in kms mode.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
