Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Mitigations for Spectre v2 on some Freescale (NXP) CPUs.
- A large series adding support for pass-through of Nvidia V100 GPUs
to guests on Power9.
- Another large series to enable hardware assistance for TLB table
walk on MPC8xx CPUs.
- Some preparatory changes to our DMA code, to make way for further
cleanups from Christoph.
- Several fixes for our Transactional Memory handling discovered by
fuzzing the signal return path.
- Support for generating our system call table(s) from a text file
like other architectures.
- A fix to our page fault handler so that instead of generating a
WARN_ON_ONCE, user accesses of kernel addresses instead print a
ratelimited and appropriately scary warning.
- A cosmetic change to make our unhandled page fault messages more
similar to other arches and also more compact and informative.
- Freescale updates from Scott:
"Highlights include elimination of legacy clock bindings use from
dts files, an 83xx watchdog handler, fixes to old dts interrupt
errors, and some minor cleanup."
And many clean-ups, reworks and minor fixes etc.
Thanks to: Alexandre Belloni, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Arnd Bergmann, Benjamin Herrenschmidt, Breno Leitao,
Christian Lamparter, Christophe Leroy, Christoph Hellwig, Daniel
Axtens, Darren Stevens, David Gibson, Diana Craciun, Dmitry V. Levin,
Firoz Khan, Geert Uytterhoeven, Greg Kurz, Gustavo Romero, Hari
Bathini, Joel Stanley, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Michal Suchánek, Naveen
N. Rao, Nick Desaulniers, Oliver O'Halloran, Paul Mackerras, Ram Pai,
Ravi Bangoria, Rob Herring, Russell Currey, Sabyasachi Gupta, Sam
Bobroff, Satheesh Rajendran, Scott Wood, Segher Boessenkool, Stephen
Rothwell, Tang Yuantian, Thiago Jung Bauermann, Yangtao Li, Yuantian
Tang, Yue Haibing"
* tag 'powerpc-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (201 commits)
Revert "powerpc/fsl_pci: simplify fsl_pci_dma_set_mask"
powerpc/zImage: Also check for stdout-path
powerpc: Fix HMIs on big-endian with CONFIG_RELOCATABLE=y
macintosh: Use of_node_name_{eq, prefix} for node name comparisons
ide: Use of_node_name_eq for node name comparisons
powerpc: Use of_node_name_eq for node name comparisons
powerpc/pseries/pmem: Convert to %pOFn instead of device_node.name
powerpc/mm: Remove very old comment in hash-4k.h
powerpc/pseries: Fix node leak in update_lmb_associativity_index()
powerpc/configs/85xx: Enable CONFIG_DEBUG_KERNEL
powerpc/dts/fsl: Fix dtc-flagged interrupt errors
clk: qoriq: add more compatibles strings
powerpc/fsl: Use new clockgen binding
powerpc/83xx: handle machine check caused by watchdog timer
powerpc/fsl-rio: fix spelling mistake "reserverd" -> "reserved"
powerpc/fsl_pci: simplify fsl_pci_dma_set_mask
arch/powerpc/fsl_rmu: Use dma_zalloc_coherent
vfio_pci: Add NVIDIA GV100GL [Tesla V100 SXM2] subdriver
vfio_pci: Allow regions to add own capabilities
vfio_pci: Allow mapping extra regions
...
Pull timer updates from Thomas Gleixner:
"The timer department delivers the following christmas presents:
Core code:
- Use proper seqcount initializer to make lockdep happy
- SPDX annotations and cleanup of license boilerplates
- Use DEFINE_SHOW_ATTRIBUTE() instead of open coding it
- Minor cleanups
Driver code:
- Add the sched_clock for the arc timer (Alexey Brodkin)
- Change the file timer names for riscv, rockchip, tegra20, sun4i and
meson6 (Daniel Lezcano)
- Add the DT bindings for r8a7796, r8a77470 and r8a774a1 (Biju Das)
- Remove the early platform driver registration for timer-ti-dm
(Bartosz Golaszewski)
- Provide the sched_clock for the riscv timer (Anup Patel)
- Add support for ARM64 for the imx-gpt and convert the imx-tpm to
the timer-of API (Anson Huang)
- Remove useless irq protection for the imx-gpt (Clément Péron)
- Remove a duplicate function name for the vt8500 (Dan Carpenter)
- Remove obsolete inclusion of <asm/smp_twd.h> for the tegra20 (Geert
Uytterhoeven)
- Demote the prcmu and the custom sched_clock for the dbx500 and the
ux500 (Linus Walleij)
- Add a new timer clock for the RDA8810PL (Manivannan Sadhasivam)
- Rename the macro to stick to the register name and add the delay
timer (Martin Blumenstingl)
- Switch the bcm2835 to the SPDX identifier (Stefan Wahren)
- Fix the interrupt register access on the fttmr010 (Tao Ren)
- Add missing of_node_put in the initialization path on the
integrator-ap (Yangtao Li)"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
dt-bindings: timer: Document RDA8810PL SoC timer
clocksource/drivers/rda: Add clock driver for RDA8810PL SoC
clocksource/drivers/meson6: Change name meson6_timer timer-meson6
clocksource/drivers/sun4i: Change name sun4i_timer to timer-sun4i
clocksource/drivers/tegra20: Change name tegra20_timer to timer-tegra20
clocksource/drivers/rockchip: Change name rockchip_timer to timer-rockchip
clocksource/drivers/riscv: Change name riscv_timer to timer-riscv
clocksource/drivers/riscv_timer: Provide the sched_clock
clocksource/drivers/timer-imx-tpm: Specify clock name for timer-of
clocksource/drivers/fttmr010: Fix invalid interrupt register access
clocksource/drivers/integrator-ap: Add missing of_node_put()
clocksource/drivers/bcm2835: Switch to SPDX identifier
dt-bindings: timer: renesas, cmt: Document r8a774a1 CMT support
clocksource/drivers/timer-imx-tpm: Convert the driver to timer-of
clocksource/drivers/arc_timer: Utilize generic sched_clock
dt-bindings: timer: renesas, cmt: Document r8a77470 CMT support
dt-bindings: timer: renesas, cmt: Document r8a7796 CMT support
clocksource/drivers/imx-gpt: Remove unnecessary irq protection
clocksource/drivers/imx-gpt: Add support for ARM64
clocksource/drivers/meson6_timer: Implement the ARM delay timer
...
Pull irq updates from Thomas Gleixner:
"The interrupt department provides:
Core updates:
- Better spreading to NUMA nodes in the affinity management
- Support for more than one set of interrupts to spread out to allow
separate queues for separate functionality of a single device.
- Decouple the non queue interrupts from being managed. Those are
usually general interrupts for error handling etc. and those should
never be shut down. This also a preparation to utilize the
spreading mechanism for initial spreading of non-managed interrupts
later.
- Make the single CPU target selection in the matrix allocator more
balanced so interrupts won't accumulate on single CPUs in certain
situations.
- A large spell checking patch so we don't end up fixing single typos
over and over.
Driver updates:
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for the 8MQ, F1C100s platform drivers
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation on msm8996
which sports a botched register set.
- A platform-msi fix to prevent memory leakage
- Various cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
genirq/affinity: Add is_managed to struct irq_affinity_desc
genirq/core: Introduce struct irq_affinity_desc
genirq/affinity: Remove excess indentation
irqchip/stm32: protect configuration registers with hwspinlock
dt-bindings: interrupt-controller: stm32: Document hwlock properties
irqchip: Add driver for imx-irqsteer controller
dt-bindings/irq: Add binding for Freescale IRQSTEER multiplexer
irqchip: Add driver for Cirrus Logic Madera codecs
genirq: Fix various typos in comments
irqchip/irq-imx-gpcv2: Add IRQCHIP_DECLARE for i.MX8MQ compatible
irqchip/irq-rda-intc: Fix return value check in rda8810_intc_init()
irqchip/irq-imx-gpcv2: Silence "fall through" warning
irqchip/gic-v3: Add quirk for msm8996 broken registers
irqchip/gic: Add support to device tree based quirks
dt-bindings/gic-v3: Add msm8996 compatible string
irqchip/sun4i: Add support for Allwinner ARMv5 F1C100s
irqchip/sun4i: Move IC specific register offsets to struct
irqchip/sun4i: Add a struct to hold global variables
dt-bindings: interrupt-controller: Add suniv interrupt-controller
irqchip: Add RDA8810PL interrupt driver
...
Pull clk updates from Stephen Boyd:
"This round is dominated by NXP's i.MX clk drivers. We gained support
for two or three i.MX SoCs in here and that mostly means a lot of
driver code and data.
Beyond that platform, there are some new Mediatek, Amlogic, and
Qualcomm clk drivers added in here, and then we get to the long tail
of driver updates and non-critical fixes all around, including code
for vendors such as Renesas, Rockchip, Nvidia, and Allwinner. Overall,
the driver updates look normal.
Apart from the usual driver updates we have an update to make
registering OF based clk providers a little simpler when they're
devices created as a child of a device backed by a node in DT. Drivers
don't have to jump through hoops to unregister the provider upon
driver removal anymore because the API does the right thing and uses
the parent device DT node.
Summary:
Core:
- Make devm_of_clk_add_hw_provider() use parent dt node if necessary
- Various SPDX taggings
- Mark clk_ops const when possible
New Drivers:
- NXP i.MX7ULP SoC clock support
- NXP i.MX8QXP SoC clock support
- NXP i.MX8MQ SoC clock support
- NXP QorIQ T1023 SoC support
- Qualcomm SDM845 audio subsystem clks
- Qualcomm SDM845 GPU clck controllers
- Qualcomm QCS404 RPM clk support
- Mediatek MT7629 SoC clk controllers
- Allwinner F1c100s SoC clocks
- Allwinner H6 display engine clocks
- Amlogic GX video clocks
- Support for Amlogic meson8b CPU frequency scaling
- Amlogic Meson8b CPU post-divider clocks
Updates:
- Proper suspend/resume on VersaClock5
- Shrink code some with DEFINE_SHOW_ATTRIBUTE()
- Register fixes for Rockchip rk3188 and rk3328
- One new critical clock for Rockchip rk3188 and a fixed clock id
(double used number)
- New clock id for Rockchip rk3328
- Amlogic Meson8/Meson8b video clock support
- Amlogic got a clk-input helper and used it for the axg-audio clock
driver
- Sigma Delta modulation for the Allwinner A33 audio clocks
- Support for CPEX (timer) clocks on various Renesas R-Car Gen3 and
RZ/G2 SoCs
- Support for SDHI HS400 clocks on early revisions of Renesas R-Car
H3 and M3-W
- Support for SDHI and USB clocks on Renesas RZ/A2
- Support for RPC (SPI Multi I/O Bus Controller) clocks on Renesas
R-Car V3M
- Qualcomm MSM8998 GCC driver improvements (resets, drop unused clks,
etc)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (172 commits)
clk: imx: imx7ulp: add arm hsrun mode clocks support
dt-bindings: clock: imx7ulp: add HSRUN mode related clocks
clk: Use of_node_name_eq for node name comparisons
clk: vc5: Add suspend/resume support
clk: qcom: Drop unused 8998 clock
clk: qcom: Leave mmss noc on for 8998
clk: tegra: Return the exact clock rate from clk_round_rate
clk: tegra30: Use Tegra CPU powergate helper function
soc/tegra: pmc: Drop SMP dependency from CPU APIs
clk: tegra: Fix maximum audio sync clock for Tegra124/210
clk: tegra: get rid of duplicate defines
clk: imx: add imx8qxp lpcg driver
clk: imx: add lpcg clock support
clk: imx: add imx8qxp clk driver
clk: imx: Make the i.MX8MQ CCM clock driver CLK_IMX8MQ dependant
clk: imx: add scu clock common part
clk: imx: add configuration option for mmio clks
dt-bindings: clock: add imx8qxp lpcg clock binding
dt-bindings: clock: imx8qxp: add SCU clock IDs
clk: qcom: Add missing msm8998 resets
...
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
Pull regulator updates from Mark Brown:
"This has been a very busy release for the core, some fixes, one large
new feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a
prior attempt by Maciej Purski, allowing us to handle situations
where the voltages on two regulators can't be too far apart from
each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project
to remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502"
* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
regulator: tps65910: fix a missing check of return value
regulator: mcp16502: Select REGMAP_I2C to fix build error
regulator: convert to DEFINE_SHOW_ATTRIBUTE
regulator: mcp16502: Fix missing n_voltages setting
regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
regulator: mcp16502: code cleanup
regulator: act8945a-regulator: make symbol act8945a_pm static
drivers/regulator: fix a missing check of return value
regulator: act8945a-regulator: fix 'defined but not used' compiler warning
regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
regulator: mcp16502: add support for suspend
mfd: axp20x: use explicit bit defines
mfd: axp20x: Clean up included headers
regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
regulator: axp20x: add software based soft_start for AXP209 LDO3
dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
regulator: axp20x: add support for set_ramp_delay for AXP209
mfd: axp20x: name voltage ramping define properly
regulator: mcp16502: add regulator driver for MCP16502
...
Pull pwm updates from Thierry Reding:
"Not a lot going on this cycle.
There's some more cleanup going on and new driver support that was not
quite ready in time for v4.21-rc1, but here are a few fixes and
improvements that are good to go.
The Kona PWM driver can now be built on the Cygnus architecture and
the i.MX driver gained support for hardware readback. Some small fixes
are provided for the clks711x and lpc18xx-sct drivers.
Finally, to round things off some drivers are switched to SPDX license
identifiers"
* tag 'pwm/for-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
dt-bindings: pwm: rcar: Add r8a774c0 support
pwm: imx: Add ipg clock operation
pwm: clps711x: Switch to SPDX identifier
pwm: clps711x: Fix period calculation
pwm: bcm2835: Switch to SPDX identifier
pwm: Enable Kona PWM to be built for the Cygnus architecture
pwm: Drop legacy wrapper for changing polarity
pwm: imx: Implement get_state() function for hardware readout
pwm: imx: Use bitops and bitfield macros to define register values
pwm: imx: Sort include files
pwm: lpc18xx-sct: Don't reconfigure PWM in .request and .free
Pull power management updates from Rafael Wysocki:
"These add sysadmin documentation for cpuidle, extend the cpuidle
subsystem somewhat, improve the handling of performance states in the
generic power domains (genpd) and operating performance points (OPP)
frameworks, add a new cpufreq driver for Qualcomm SoCs, update some
other cpufreq drivers, switch over the runtime PM framework to using
high-res timers for device autosuspend, fix a problem with
suspend-to-idle on ACPI-based platforms, add system-wide suspend and
resume handling to the devfreq framework, do some janitorial cleanups
all over and update some utilities.
Specifics:
- Add sysadmin documentation for cpuidle (Rafael Wysocki).
- Make it possible to specify a cpuidle governor from kernel command
line, add new cpuidle state sysfs attributes for governor
evaluation, and improve the "polling" idle state handling (Rafael
Wysocki).
- Fix the handling of the "required-opps" DT property in the
operating performance points (OPP) framework, improve the
integration of it with the generic power domains (genpd) framework,
improve the handling of performance states in them and clean up the
idle states vs performance states separation in genpd (Viresh
Kumar, Ulf Hansson).
- Add a cpufreq driver called "qcom-hw" for Qualcomm SoCs using a
hardware engine to control CPU frequency transitions along with DT
bindings for it (Taniya Das).
- Fix an intel_pstate driver issue related to CPU offline and update
the documentation of it (Srinivas Pandruvada).
- Clean up the imx6q cpufreq driver (Anson Huang).
- Add SPDX license IDs to cpufreq schedutil governor files (Daniel
Lezcano).
- Switch over the runtime PM framework to using high-res timers for
device autosuspend to allow the control of it to be more precise
(Vincent Guittot).
- Disable non-wakeup ACPI GPEs during suspend-to-idle so that they
don't prevent the system from reaching the target low-power state
and simplify the suspend-to-idle handling on ACPI platforms without
full Low-Power S0 Idle (LPS0) support (Rafael Wysocki).
- Add system-wide suspend and resume support to the devfreq framework
(Lukasz Luba).
- Clean up the SmartReflex adaptive voltage scaling (AVS) driver and
add an SPDX license ID to it (Nishanth Menon, Uwe Kleine-König,
Thomas Meyer).
- Get rid of code duplication by using the DEFINE_SHOW_ATTRIBUTE
macro in some places, fix some DT node refcount leaks, and do some
other janitorial cleanups (Yangtao Li).
- Update the cpupower, intel_pstate_tracer and turbosat utilities
(Abhishek Goel, Doug Smythies, Len Brown)"
* tag 'pm-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (54 commits)
PM / Domains: remove define_genpd_open_function() and define_genpd_debugfs_fops()
PM-runtime: Switch autosuspend over to using hrtimers
cpufreq: qcom-hw: Add support for QCOM cpufreq HW driver
dt-bindings: cpufreq: Introduce QCOM cpufreq firmware bindings
ACPI: PM: Loop in full LPS0 mode only
ACPI: EC / PM: Disable non-wakeup GPEs for suspend-to-idle
tools/power/x86/intel_pstate_tracer: Fix non root execution for post processing a trace file
tools/power turbostat: consolidate duplicate model numbers
tools/power turbostat: fix goldmont C-state limit decoding
PM / Domains: Propagate performance state updates
PM / Domains: Factorize dev_pm_genpd_set_performance_state()
PM / Domains: Save OPP table pointer in genpd
OPP: Don't return 0 on error from of_get_required_opp_performance_state()
OPP: Add dev_pm_opp_xlate_performance_state() helper
OPP: Improve _find_table_of_opp_np()
PM / Domains: Make genpd performance states orthogonal to the idlestates
PM / sleep: convert to DEFINE_SHOW_ATTRIBUTE
cpuidle: Add 'above' and 'below' idle state metrics
PM / AVS: SmartReflex: Switch to SPDX Licence ID
PM / AVS: SmartReflex: NULL check before some freeing functions is not needed
...
Pull EDAC updates from Borislav Petkov:
- Support for ZynqMP DDR controller support to synopsys_edac along with
a driver cleanup and generalization for the addition of support for
the new IP. (Manish Narani)
- Removal of the /sys/bus/edac devices hierarchy. This enabled us to
get rid of the silly memory controllers maximum number notion. (Tony
Luck and Borislav Petkov)
- skx_edac improvements and fixes. (Qiuxu Zhuo and Tony Luck)
- The usual garden variety of small cleanups and fixes.
* tag 'edac_for_4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (25 commits)
EDAC, fsl_ddr: Add LS1021A to the list of supported hardware
EDAC, i5000: Remove set but not used local variables
MAINTAINERS, EDAC: Drop bouncing email
EDAC, i82975x: Fix spelling mistake "reserverd" -> "reserved"
EDAC, fsl: Move error injection under CONFIG_EDAC_DEBUG
EDAC, skx: Let EDAC core show the decoded result for debugfs
EDAC, skx: Move debugfs node under EDAC's hierarchy
EDAC, skx: Prepend hex formatting with '0x'
EDAC, skx: Fix function calling order in skx_exit()
EDAC: Drop per-memory controller buses
EDAC: Don't add devices under /sys/bus/edac
EDAC: Fix indentation issues in several EDAC drivers
EDAC, skx: Fix randconfig builds in a better way
EDAC, i82975x: Remove set but not used variable dtype
EDAC, qcom_edac: Remove irq_handled local variable
EDAC, synopsys: Add Error Injection support for ZynqMP DDR controller
EDAC, synopsys: Add ECC support for ZynqMP DDR controller
EDAC, synopsys: Add macro defines for ZynqMP DDRC
dt: bindings: Document ZynqMP DDRC in Synopsys documentation
EDAC, synopsys: Add error handling for the of_device_get_match_data() result
...
Pull sound updates from Takashi Iwai:
"There are no intensive changes in both ALSA and ASoC core parts while
rather most of changes are a bunch of driver fixes and updates. A
large diff pattern appears in ASoC TI part which now merges both OMAP
and DaVinci stuff, but the rest spreads allover the places.
Note that this pull request includes also some updates for LED trigger
and platform drivers for mute LEDs, appearing in the diffstat as well.
Some highlights:
ASoC:
- Preparatory work for merging the audio-graph and audio-graph-scu
cards
- A merge of TI OMAP and DaVinci directories, as both product lines
get merged together. Also including a few architecture changes as
well.
- Major cleanups of the Maxim MAX9867 driver
- Small fixes for tablets & co with Intel BYT/CHT chips
- Lots of rsnd updates as usual
- Support for Asahi Kaesi AKM4118, AMD ACP3x, Intel platforms with
RT5660, Meson AXG S/PDIF inputs, several Qualcomm IPs and Xilinx
I2S controllers
HD-audio:
- Introduce audio-mute LED trigger for replacing the former hackish
dynamic binding
- Huawei WMI hotkey and mute LED support
- Refactoring of PM code and display power controls
- Headset button support in the generic jack code
- A few updates for Tegra
- Fixups for HP EliteBook and ASUS UX391UA
- Lots of updates for Intel ASoC HD-audio, including the improved DSP
detection and the fallback binding from ASoC SST to legacy HD-audio
controller drivers
Others:
- Updates for FireWire TASCAM and Fireface devices, some other fixes
- A few potential Spectre v1 fixes that are all trivial"
* tag 'sound-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: HD-Audio: SKL+: force HDaudio legacy or SKL+ driver selection
ALSA: HD-Audio: SKL+: abort probe if DSP is present and Skylake driver selected
ALSA: HDA: export process_unsol_events()
ALSA: hda/realtek: Enable audio jacks of ASUS UX391UA with ALC294
ALSA: bebob: fix model-id of unit for Apogee Ensemble
ALSA: emu10k1: Fix potential Spectre v1 vulnerabilities
ALSA: rme9652: Fix potential Spectre v1 vulnerability
ASoC: ti: Kconfig: Remove the deprecated options
ARM: davinci_all_defconfig: Update the audio options
ARM: omap1_defconfig: Do not select ASoC by default
ARM: omap2plus_defconfig: Update the audio options
ARM: davinci: dm365-evm: Update for the new ASoC Kcofnig options
ARM: OMAP2: Update for new MCBSP Kconfig option
ARM: OMAP1: Makefile: Update for new MCBSP Kconfig option
MAINTAINERS: Add entry for sound/soc/ti and update the OMAP audio support
ASoC: ti: Merge davinci and omap directories
ALSA: hda: add mute LED support for HP EliteBook 840 G4
ALSA: fireface: code refactoring to handle model-specific registers
ALSA: fireface: add support for packet streaming on Fireface 800
ALSA: fireface: allocate isochronous resources in mode-specific implementation
...
Pull media updates from Mauro Carvalho Chehab:
"First set of media patches contains:
- Three new platform drivers: aspeed-video seco-sed and sun5i-csi;
- One new sensor driver: imx214;
- Support for Xbox DVD Movie Playback kit remote controller;
- Removal of the legacy friio driver. The functionalities were ported
to another driver, already merged;
- New staging driver: Rockchip VPU;
- Added license text or SPDX tags to all media documentation files;
- Usual set of cleanup, fixes and enhancements"
* tag 'media/v4.20-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (263 commits)
media: cx23885: only reset DMA on problematic CPUs
media: ddbridge: Move asm includes after linux ones
media: drxk_hard: check if parameter is not NULL
media: docs: fix some GPL licensing ambiguity at the text
media: platform: Add Aspeed Video Engine driver
media: dt-bindings: media: Add Aspeed Video Engine binding documentation
media: vimc: fix start stream when link is disabled
media: v4l2-device: Link subdevices to their parent devices if available
media: siano: Use kmemdup instead of duplicating its function
media: rockchip vpu: remove some unused vars
media: cedrus: don't initialize pointers with zero
media: cetrus: return an error if alloc fails
media: cedrus: Add device-tree compatible and variant for A64 support
media: cedrus: Add device-tree compatible and variant for H5 support
media: dt-bindings: media: cedrus: Add compatibles for the A64 and H5
media: video-i2c: check if chip struct has set_power function
media: video-i2c: support runtime PM
media: staging: media: imx: Use of_node_name_eq for node name comparisons
media: v4l2-subdev: document controls need _FL_HAS_DEVNODE
media: vivid: Improve timestamping
...
Pull mtd updates from Boris Brezillon:
"SPI NOR Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra,
vf610):
* Stop to pass mtd_info objects to internal functions
* Reorganize code to avoid forward declarations
* Drop useless test in nand_legacy_set_defaults()
* Move nand_exec_op() to internal.h
* Add nand_[de]select_target() helpers
* Pass the CS line to be selected in struct nand_operation
* Make ->select_chip() optional when ->exec_op() is implemented
* Deprecate the ->select_chip() hook
* Move the ->exec_op() method to nand_controller_ops
* Move ->setup_data_interface() to nand_controller_ops
* Deprecate the dummy_controller field
* Fix JEDEC detection
* Provide a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flag 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fix the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Drop .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Remove denali_reset_banks()
* Remove ->dev_ready() hook
* Include <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Add an SPDX tag to replace the license text
* Make conversion from chip to fsmc consistent
* Fix unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Prevent timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Convert to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Add an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Remove the depreacated mt29f_spinand driver from staging.
- Add support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
JFFS2 changes:
- Fix a lockdep issue
MTD changes:
- Rework the physmap driver to merge gpio-addr-flash and physmap_of
in it
- Add a new compatible for RedBoot partitions
- Make sub-partitions RW if the parent partition was RO because of a
mis-alignment
- Add pinctrl support to the
- Addition of /* fall-through */ comments where appropriate
- Various minor fixes and cleanups
Other changes:
- Update my email address"
* tag 'mtd/for-4.21' of git://git.infradead.org/linux-mtd: (108 commits)
mtd: rawnand: sunxi: Write pageprog related opcodes to WCMD_SET
MAINTAINERS: Update my email address
mtd: rawnand: marvell: prevent timeouts on a loaded machine
mtd: rawnand: omap2: Pass the parent of pdev to dma_request_chan()
mtd: rawnand: Fix JEDEC detection
mtd: spi-nor: Add support for is25lp016d
mtd: spi-nor: parse SFDP 4-byte Address Instruction Table
mtd: spi-nor: Add 4B_OPCODES flag to is25lp256
mtd: spi-nor: Add an SPDX tag to spi-nor.{c,h}
mtd: spi-nor: Make the enable argument passed to set_byte() a bool
mtd: spi-nor: Stop passing flash_info around
mtd: spi-nor: Avoid forward declaration of internal functions
mtd: spi-nor: Drop inline on all internal helpers
mtd: spi-nor: Add a post BFPT fixup for MX25L25635E
mtd: spi-nor: Add a post BFPT parsing fixup hook
mtd: spi-nor: Add the SNOR_F_4B_OPCODES flag
mtd: spi-nor: cast to u64 to avoid uint overflows
mtd: spi-nor: Add support for IS25LP032/064
mtd: spi-nor: add entry for mt35xu512aba flash
mtd: spi-nor: add macros related to MICRON flash
...
Pull initial i3c support from Boris Brezillon:
"Add initial support for I3C along with two I3C master controller
drivers"
* tag 'i3c/for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: cdns: fix I2C transfers in Cadence I3C master driver
ic3: off by one in mode_show()
i3c: fix an error code in i3c_master_add_i3c_dev_locked()
i3c: master: dw: fix mask operation by using the correct operator
MAINTAINERS: Add myself as the dw-i3c-master module maintainer
dt-binding: i3c: Document Synopsys DesignWare I3C
i3c: master: Add driver for Synopsys DesignWare IP
i3c: master: Remove set but not used variable 'old_i3c_scl_lim'
dt-bindings: i3c: Document Cadence I3C master bindings
i3c: master: Add driver for Cadence IP
MAINTAINERS: Add myself as the I3C subsystem maintainer
dt-bindings: i3c: Document core bindings
i3c: Add sysfs ABI spec
docs: driver-api: Add I3C documentation
i3c: Add core I3C infrastructure
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove fine-tune property in device tree, modify
the corresponding description in dt-binding.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM4330 is a 802.11 a/b/g/n WiFi + Bluetooth 4.0 chip from Broadcom.
It is found in the Ampak AP6330 WiFi+BT module. The partiular one I have
identifies as BCM4330B1 for Bluetooth and BCM4330/4 for WiFi.
It is unclear if the AP6330 module uses this revision of the BCM4330, or
if there are multiple revisions. The module does not have revision
markings. This patch elects to use just BCM4330 for the compatible
string.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM20702A1 is a Bluetooth 4.0 chip from Broadcom. It is found in the
Ampak AP6210 WiFi+BT module, identified from the read verbose config info
command response. However the Bluetooth firmware provided by vendors uses
the name BCM20710. This patch elects to use the chip ID returned by the
chip for the compatible string.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
This patch adds properties for the two so we can describe the power
supply relationships.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers can take up to two external clocks:
an external frequency reference, substituting the main crystal, and a
LPO clock at 32.768 kHz substituting the internal LPO clock.
In particular, the external LPO clock must be used when the controller
does not have NVRAM connected, and the main reference frequency is not
the default 20 MHz. This is described in detail in the datasheet.
The original "extclk" clock name is ambiguous as to which of these it
refers to, and some designs might even require both.
This patch deprecates the existing name, and adds "txco" and "lpo".
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
Pull irqchip updates from Marc Zyngier:
- A bunch of new irqchip drivers (RDA8810PL, Madera, imx-irqsteer)
- Updates for new (and old) platforms (i.MX8MQ, F1C100s)
- A number of SPDX cleanups
- A workaround for a very broken GICv3 implementation
- A platform-msi fix
- Various cleanups
This adds the DT binding for the Freescale IRQSTEER interrupt
multiplexer found in the i.MX8 familiy SoCs.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Linux 4.20-rc7
* tag 'v4.20-rc7': (403 commits)
Linux 4.20-rc7
scripts/spdxcheck.py: always open files in binary mode
checkstack.pl: fix for aarch64
userfaultfd: check VM_MAYWRITE was set after verifying the uffd is registered
fs/iomap.c: get/put the page in iomap_page_create/release()
hugetlbfs: call VM_BUG_ON_PAGE earlier in free_huge_page()
memblock: annotate memblock_is_reserved() with __init_memblock
psi: fix reference to kernel commandline enable
arch/sh/include/asm/io.h: provide prototypes for PCI I/O mapping in asm/io.h
mm/sparse: add common helper to mark all memblocks present
mm: introduce common STRUCT_PAGE_MAX_SHIFT define
alpha: fix hang caused by the bootmem removal
XArray: Fix xa_alloc when id exceeds max
drm/vmwgfx: Protect from excessive execbuf kernel memory allocations v3
MAINTAINERS: Daniel for drm co-maintainer
drm/amdgpu: drop fclk/gfxclk ratio setting
IB/core: Fix oops in netdev_next_upper_dev_rcu()
dm thin: bump target version
drm/vmwgfx: remove redundant return ret statement
drm/i915: Flush GPU relocs harder for gen3
...
* clk-renesas:
clk: renesas: rcar-gen3: Add HS400 quirk for SD clock
clk: renesas: rcar-gen3: Add documentation for SD clocks
clk: renesas: rcar-gen3: Set state when registering SD clocks
clk: renesas: r8a77995: Simplify PLL3 multiplier/divider
clk: renesas: r8a77995: Add missing CPEX clock
clk: renesas: r8a77995: Remove non-existent SSP clocks
clk: renesas: r8a77995: Remove non-existent VIN5-7 module clocks
clk: renesas: r8a77995: Correct parent clock of DU
clk: renesas: r8a77990: Correct parent clock of DU
clk: renesas: r8a77970: Add CPEX clock
clk: renesas: r8a77965: Add CPEX clock
clk: renesas: r8a7796: Add CPEX clock
clk: renesas: r8a7795: Add CPEX clock
clk: renesas: r8a774a1: Add CPEX clock
dt-bindings: clock: r8a7796: Remove CSIREF clock
dt-bindings: clock: r8a7795: Remove CSIREF clock
clk: renesas: Mark rza2_cpg_clk_register static
clk: renesas: r7s9210: Add USB clocks
clk: renesas: r8a77970: Add RPC clocks
clk: renesas: r7s9210: Add SDHI clocks
* clk-allwinner:
clk: sunxi-ng: a64: Allow parent change for VE clock
clk: sunxi-ng: a33: Set CLK_SET_RATE_PARENT for all audio module clocks
clk: sunxi-ng: a33: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: h3: Allow parent change for ve clock
clk: sunxi-ng: add support for suniv F1C100s SoC
dt-bindings: clock: Add Allwinner suniv F1C100s CCU
clk: sunxi-ng: h3/h5: Fix CSI_MCLK parent
clk: sunxi-ng: r40: Force LOSC parent to RTC LOSC output
clk: sunxi-ng: sun50i: a64: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: a64: Fix gate bit of DSI DPHY
clk: sunxi-ng: Enable DE2_CCU for SUN8I and SUN50I
clk: sunxi-ng: Add support for H6 DE3 clocks
dt-bindings: clock: sun8i-de2: Add H6 DE3 clock description
clk: sunxi-ng: h6: Set video PLLs limits
clk: sunxi-ng: Use u64 for calculation of NM rate
clk: sunxi-ng: Adjust MP clock parent rate when allowed
clk: sunxi-ng: sun50i: h6: Fix MMC clock mux width
clk: sunxi-ng: enable so-said LDOs for A64 SoC's pll-mipi clock
* clk-tegra:
clk: tegra: Return the exact clock rate from clk_round_rate
clk: tegra30: Use Tegra CPU powergate helper function
soc/tegra: pmc: Drop SMP dependency from CPU APIs
clk: tegra: Fix maximum audio sync clock for Tegra124/210
clk: tegra: get rid of duplicate defines
clk: tegra20: Check whether direct PLLM sourcing is turned off for EMC
clk: tegra20: Turn EMC clock gate into divider
* clk-meson: (25 commits)
clk: meson: axg-audio: use the clk input helper function
clk: meson: add clk-input helper function
clk: meson: Mark some things static
clk: meson: meson8b: add the read-only video clock trees
clk: meson: meson8b: add the fractional divider for vid_pll_dco
clk: meson: meson8b: fix the offset of vid_pll_dco's N value
clk: meson: Fix GXL HDMI PLL fractional bits width
clk: meson: meson8b: add the CPU clock post divider clocks
clk: meson: meson8b: rename cpu_div2/cpu_div3 to cpu_in_div2/cpu_in_div3
clk: meson: clk-regmap: add read-only gate ops
clk: meson: meson8b: allow changing the CPU clock tree
clk: meson: meson8b: run from the XTAL when changing the CPU frequency
clk: meson: meson8b: add support for more M/N values in sys_pll
clk: meson: meson8b: mark the CPU clock as CLK_IS_CRITICAL
clk: meson: meson8b: do not use cpu_div3 for cpu_scale_out_sel
clk: meson: clk-pll: check if the clock is already enabled
clk: meson: meson8b: fix the width of the cpu_scale_div clock
clk: meson: meson8b: fix incorrect divider mapping in cpu_scale_table
clk: meson: meson8b: use the HHI syscon if available
dt-bindings: clock: meson8b: use the registers from the HHI syscon
...
* clk-rockchip:
clk: rockchip: add clock-id to gate of ACODEC for rk3328
clk: rockchip: add clock ID of ACODEC for rk3328
clk: rockchip: fix ID of 8ch clock of I2S1 for rk3328
clk: rockchip: fix I2S1 clock gate register for rk3328
clk: rockchip: make rk3188 hclk_vio_bus critical
clk: rockchip: fix rk3188 sclk_mac_lbtest parameter ordering
clk: rockchip: fix rk3188 sclk_smc gate data
clk: rockchip: fix typo in rk3188 spdif_frac parent
- NXP QorIQ T1023 SoC support
- Introduce a 'protected-clocks' binding for firmware protected clks
- Shrink code some with DEFINE_SHOW_ATTRIBUTE()
* clk-qoriq-t1023:
clk: qoriq: add more chips support
* clk-protected-binding:
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
* clk-define-show-macro:
clk: tegra: Change to use DEFINE_SHOW_ATTRIBUTE macro
clk: nomadik: Change to use DEFINE_SHOW_ATTRIBUTE macro
* clk-static:
clk: stm32mp1: drop pointless static qualifier in stm32_register_hw_clk()
This patch adds board specific bindings required for dais, In particular
for compressed dais and dai direction.
Board specific setup involves setting up some of dais as compressed dais
and also specify direction of any dai. Some of the dais might only
support capture/playback depending on the board level wiring.
These two new dt properties will allow such flexibilty at board level dts.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
