Now that mac80211 creates templates for PS Poll and Nullfunc frames, use
them instead of creating our own.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a timeout bug in
/drivers/net/wireless/wl12xx/wl1271_spi.c
In the current code you cannot tell why you exited
the "poll for data ready" do-while loop if exiting
was done after the last possible loop.
Then timeout==0 regardless of (val & OCP_READY_MASK) or
!(val & OCP_READY_MASK), leading to possible false timeout...
Simple correction could be decreasing timeout after checking
for !(val & OCP_READY_MASK), not before
(Manually converted from email to an actual patch by me. -- JWL)
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.
Add checking for the vif.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In reference source, events are acknowledged separately - fix the driver to
do the same.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure correct values to be used with the smart-reflex configuration of the
firmware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the data path configuration, one of the parameters is the channel. We
have been setting it to wl->channel, which is not correct in this case. This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase. Hardcoded the channel to 1,
according to the reference driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the new reference driver, some of the firmware configuration values have
been changed. This patch changes them in the wl1271 driver accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values. For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided. It always contains the gpio
power setting (0 = off, 1 = on). To change the power setting, just write 0
or 1 to the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmwares require the dco itrim parameters to be set during
initialization. This patch implements the new ACX function and calls it.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init. We should use WL1271_DEFAULT_BASIC_RATE_SET instead. The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail. This patch adds the call and now PS seems to
work.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that. This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we're using a the idle information coming from mac80211 to decide when to
disconnect. If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command. So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we need to change the channel before association, we have to send a join
command with a valid BSSID. With this patch we use 0baddeadbeef as the
BSSID. There are ongoing discussions with TI to get this done in a cleaner
way.
When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were some changes in the values we have to use for these settings. This
patches updates them.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the general parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the radio parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before transmission when aligning the buffer to 4-byte bounday, tx_hdr
needs to be updated. Otherwise debug logs print false data.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that necessary commands for WMM are implemented, implement queue handling
for WMM. But WMM is not enabled yet, only one queue is used.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Needed for WMM.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Based on a patch for wl1271 by Luis R. Rodriguez.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wakeup time calculation was too complicated, simplify it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original TI driver uses 100 ms timeout ELP wakeup timeout, better
to use the same. Otherwise problems with wakeup might get unnoticed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all return values were checked and one exit from function didn't put
firmware sleep after the error.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This debug message was missing and caused incomplete log messages.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes when debugging the state is good info.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
