This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All instances of this device are now coming from device tree-
enabled platforms probing without using platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.
Fixes: f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs)
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As this driver is using pinconf_generic_dt_node_to_map_pin() it
needs to depend on OF so as not to cause build problems on
archs that do not support OF.
Cc: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Probe function had commas instead of semi-colons on some of the lines.
This patch just fixes those lines. No functional chagnes done in this
patch.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Also assign the gpio_chip.dev pointer to be used for error
messages.
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
busses like i2c, spi and so on can parse the virq of their subnode automatically by
irq_of_parse_and_map(). for example, i2c will do that in of_i2c_register_devices().
people can put hwirq number attached to a gpio controller in dts, and drivers can
directly request the parsed virq.
for example, for an i2c client as below,
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
interrupt-parent = <&gpio>;
interrupts = <3 0>;
reg = <0x5c>;
};
in i2c client probe(), it will request_irq(client->irq, ...) without
calling gpio_direction_input().
so here when we set irq type, we also put the pin to input direction.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
in sirfsoc gpio probe(), we create 5 irq_domains for 5 gpio banks. but
in irq_create_of_mapping() of irqchip core level, irq_find_host() can
only return the 1st irq_domain attached the pinctrl dt device node as
we can see from the codes:
unsigned int irq_create_of_mapping(struct device_node *controller,
const u32 *intspec, unsigned int intsize)
{
struct irq_domain *domain;
...
domain = controller ? irq_find_host(controller) : irq_default_domain;
}
struct irq_domain *irq_find_host(struct device_node *node)
{
struct irq_domain *h, *found = NULL;
int rc;
/* We might want to match the legacy controller last since
* it might potentially be set to match all interrupts in
* the absence of a device node. This isn't a problem so far
* yet though...
*/
mutex_lock(&irq_domain_mutex);
list_for_each_entry(h, &irq_domain_list, link) {
if (h->ops->match)
rc = h->ops->match(h, node);
else
rc = (h->of_node != NULL) && (h->of_node == node);
if (rc) {
found = h;
break;
}
}
mutex_unlock(&irq_domain_mutex);
return found;
}
for sirfsoc, the 1st irq_domain attached to the device_node(controller) only
can do linear for the 1st 32 gpios. so for devices who use gpio hwirq above
32 and put the information in dt like:
tangoc-ts@5c{
compatible = "pixcir,tangoc-ts";
+ interrupt-parent = <&gpio>;
+ interrupts = <34 0>;
};
we will fail to get the virq for these devices as hwirq will be bigger than
domain->revmap_data.linear.size in:
unsigned int irq_linear_revmap(struct irq_domain *domain,
irq_hw_number_t hwirq)
{
/* Check revmap bounds; complain if exceeded */
if (WARN_ON(hwirq >= domain->revmap_data.linear.size))
return 0;
return domain->revmap_data.linear.revmap[hwirq];
}
this patch drops redundant irq_domain and keep only one to fix the problem.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 4e7e8017a8 (pinctrl: pinctrl-single:
enhance to configure multiple pins of different modules) improved
support for pinctrl-single,bits option, but also caused a regression
in parsing badly configured mask data.
If the masks in DT data are not quite right,
pcs_parse_bits_in_pinctrl_entry() can end up in an infinite loop,
trashing memory at the same time.
Add a check to verify that each loop actually removes bits from the
'mask', so that the loop can eventually end.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pcs_enable() uses vals->mask instead of pcs->fmask when bits_per_mux is
enabled. However, pcs_disable() always uses pcs->fmask.
Fix pcs_disable() to use vals->mask with bits_per_mux.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If pins are used for function output like pwm, clk32k,
power good etc then set it as output mode default.
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP0 has multiple functions, and has RX and TX frame sync signals,
for some scenarios like audio PCM, we don't need both of them.
so here we add two possibilities for USP0 only holding one of TX
and RX frame sync.
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Barry Song <Barry.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sdmmc5 has only 3 pins CMD, CLK, DATA which are connected with CSR
TriG RF multi-GNSS. The hardware connection is like:
DATA -- GPS_SGN
CLK -- GPS_RF_CLK
CMD -- GPS_MAG
here we drop redundant pins in sdmmc5 group.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit af614b2301 adds lost USP-based UART pin groups for prima2,
but missed usp1_uart_nostreamctrl group for atlas6, this patch fixes it.
this makes USP(Universal Serial Ports) port1 can work as uart without
stream ctrl.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the clock output pin functions on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds VIN[0-2] pinmux support to r8a7791 SoC.
VIN1 B mirror is also added along with the primary
configuration since it's the only one that provides
access to all 24 data bits on VIN1.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This groups USB PWEN and OVC pins together on R8A7791 SoC,
the same way it's done on R8A7790, since both are needed
for a USB device.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arrays are never modified, declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The arrays are never modified, make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The enum_ids and var_field_width fields of struct pinmux_data_reg and
pinmux_cfg_reg are initialized using compound literals. Cast them to
const to store them in .rodata.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set g->out_bit bit for gpio output high, clear g->out_bit bit for gpio output
low.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the clk_prepare and clk_enable calls by a single
clk_prepare_enable call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clk_unprepare shall be called before clk_disable.
Fix the issue by replacing the clk_unprepare and clk_disable calls by a
single clk_disable_unprepare call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the more specific form 8974 for the compatible to reduce the
risk of future mishaps.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make the bitmaps part of the msm_pinctrl allocation instead of
separately allocating them.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIOLIB and OF as dependencies for PINCTRL_MSM8X74, to fix
build errors from i386-randconfig.
Also add help text and make the entries tristate, while touching
these entries.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[Rebased on top of pin control development branch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to get the pin configuration by using debugfs. On my system:
# cat /sys/kernel/debug/pinctrl/pinctrl.3/pinconf-pins
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra124 pinmux, and required
parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CC: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There's more than one window, name the field windows.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes catching duplicate entries easier. Merge the two IRQ9 entries
found after sorting.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The external IRQ15 input multiplexed on GPIO 0 is missing. Add it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0 is a valid GPIO value, use -1 to terminate the gpios array in IRQ
lists.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some indices take positive values only, make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ops->pin_config_get() is only used in one specific path that will only be taken
for generic pinconf drivers (ops->is_generic == true) when dumping the pinconf
by using debugfs.
By removing the check in pinconf_check_ops(), let's stop pressuring people to
write a pin_config_get() function that will never be used and so will probably
never be tested.
Removing the check in pinconf_pins_show() allows driver to not implement
pin_config_get() but still get a dump of the pinconf in debugfs by implementing
pin_config_dbg_show().
Finally, not implementing pin_config_get() now results in returning -ENOTSUPP
instead of -EINVAL. While this doesn't have any real impact for now, this feels
more right.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When passing a not initialized config parameter, at91_pinconf_get() would return
a bogus value. Fix that by initializing it to zero before using it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are VIN2 and VIN3 channels available on the R8A7790 SoC.
VIN2 supports 4/8/16/18/24-bit data, while VIN3 supports 8-bit.
Add both here, covering all possible data pin configurations.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Both VIN0 and VIN1 channels support identical input interfaces.
Add missing VIN1 pins here and organize them in the same pin
groups as VIN0.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This reorganizes and renames VIN0 data pin groups to cover
all possible configurations. There's total of eight data
pin groups, one per each configuration. Most of the groups
share the same pin/mux array. Only the 18-bit configuration
needs a separate pin/mux array since in combines interleaved
data pins.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This groups VIN0 HSYNC and VSYNC pins together
since one cannot be used without another.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This drops superfluous "signal" word from the pin group names
and renames data_enable group to clkenb as in the h/w manual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The macro is defined identically in four different locations. Share it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commit 7cbb0e55e2 ("sh-pfc: Don't duplicate argument to PINMUX_GPIO
macro") erronesouly modified the PINMUX_GPIO macro in a way that
resulted in all pins being named "name". Fix the macro to name the pins
correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had a compilation failure on x86_64 due to missing OF support
as this was an implicit dependency. Add an explicit dependency
on OF and OF_IRQ on the SoC driver.
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v2->v3:
- Total failure with older approaches: what we need to do is
have the *SoC subdriver* depend on OF and OF_IRQ. This is
because the placeholder bool PINCTRL_MSM cannot cascade its
dependencies when a subdriver selects it, Kconfig is smart
but not that smart.
ChangeLog v1->v2:
- OK so "depends on OF" did not work here let's try to simply
select OF and OF_IRQ for this then? It's one of those
"warning: (PINCTRL_MSM8X74) selects PINCTRL_MSM which has
unmet direct dependencies (PINCTRL && OF)" that I simply
cannot find my way out of :-/
This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial definition of parameters for pinctrl-msm for the msm8x74
platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the two members of struct gpio_chip that were
defined as unsigned foo:1 to bool, because that is indeed what
they are. Switch all users in the gpio and pinctrl subsystems
to assign these values with true/false instead of 0/1. The
users outside these subsystems will survive since true/false
is 1/0, atleast we set some kind of more strict typing example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When computing the pin configuration register offset the bias setup code
erroneously compares the pin number range with the loop index instead of
the pin number. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When computing the pin configuration register offset the bias setup code
erroneously compares the pin number range with the loop index instead of
the pin number. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default gpiolib debug output shows pin labels.
We want baytrail custom debug output to have the same functionality.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the new ACPI ID (INT33FC) for the BayTrail GPIO
banks as seen on a BayTrail M System-On-Chip platform. This
ACPI ID is used by the BayTrail GPIO (pinctrl) driver to
manage the Low Power Subsystem (LPSS).
Signed-off-by: Paul Drews <paul.drews@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After the patches deleting the last board registering this
pin controller as a platform device has been deleted,
proceed to remove the non-DT boot patch and depend on
OF being available and the device to be coming up by
a DT node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This decomissions the platform data header (which is no longer
in use after the systems using this driver were switched to
a pure device-tree config path) and merges the result into
the driver file or local driver header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut and paste from the imx35 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx25.h.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support gpio devicetree subnodes to allow a more detailed DT hardware
description.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IMX/MXC selects USE_OF at architecture level, so the OF dependency
at individual SoC pinctrl driver level can just be dropped.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we now grab IRQs also without first reserving the GPIO
line, let's print the mapped IRQ unconditionally in the
debugfs file as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the sync_1 group to sync as the device has a single sync pin
group for the DU, move the cde_disp mux array right after the
corresponding pins array, and split the clk_in pins in three separate
groups as the pins can be used independently.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to unlock here before returning -EINVAL.
Fixes: 6ca5274d1d ('pinctrl: rockchip: add rk3188 specifics')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I sent a patch to fix some bitwise AND tests but I guess I missed some.
Sorry about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a copy and paste bug so we test "info->reg_base" instead of
"info->reg_pull".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On OMAPs the IO ring must be rearmed each time the pad wakeup
configuration is changed. So call pcs_soc->rearm() from
pcs_irq_set().
As pinctrl-single is now an interrupt controller in some cases,
we should follow the standards and keep the interrupts enabled
constantly, and not just for wake-up events. The tracking of
runtime vs wake-up interrupts can be handled separately for
the automated runtime PM solution when we have it in the
future.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: removed wrong comment, updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
- Blackfin ADI pin control driver, we move yet another
architecture under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control
driver. New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things,
this enabled simplified device tree bindings by referring
entire groups of pins on some pin controller to act as
back-end for a certain GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged
through this tree, so the ARC has full support for pins
and GPIOs after this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin
controller instances. The i.MX1 and i.MX27 is an entirely
new family (silicon) of controllers whereas i.MX50 is
a variant of the previous supported controller.
- Then the usual slew of fixes, cleanups and incremental
updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=z9SM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
Add code to support the specific pin arrangements of the Freescale IMX50 SoC.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The #define for the maximum number of GPIO blocks was retrieved
into pinctrl-at91.c by implicit inclusion of <mach/gpio.h>
from <linux/gpio.h> creating a dependency on machine-local
<mach/gpio.h>. Break the depenency by copying this single
define into the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes a test whether the 'desc' variable is NULL.
This possibility has already been eliminated by the
below test earlier in the loop:
if (desc == NULL) {
dev_warn(pctldev->dev,
"could not get pin desc for pin %d\n",
pins[i]);
continue;
}
Found with Coverity: CID #1090078
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit: "pinctrl: imx: Use struct type for pins" relaced
pin->input_reg by pin->input_val wrongly, fix it at this commit.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx27 pincontrol driver using the imx1 core driver. The DT bindings are
similar to other imx pincontrol drivers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core driver for register formats of imx1/imx21/imx27 processors.
The pins of those processors are grouped into ports. Each port has 32
pins. The pins mux configuration is controlled by registers with 1 or 2
bit per pin, depending on the specific control register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add PFC support for the r8a7791 SoC V2 including pin groups for
on-chip devices such as MSIOF, SCIF, USB, MMC, SDHI, DU.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Kunihito Higashiyama <kunihito.higashiyama.ur@renesas.com>
Signed-off-by: Yoshikazu Fujikawa <yoshikazu.fujikawa.ue@renesas.com>
Signed-off-by: Nobuyuki HIRAI <nobuyuki.hirai.xe@renesas.com>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, minor fixes]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add CAN data and clock pin groups to R8A7778 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix the error handling in tb10x_pinctrl_probe():
- devm_ioremap_resource() return ERR_PTR() and never return NULL
- remove the dev_err call to avoid redundant error message
- pinctrl_register() returns NULL not ERR_PTR()
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Looks like we need a little bit of arch specific handling
with the generic IRQ. Fix the issue with an ifdef the
same way as other drivers do.
ARM needs things set to IRQF_VALID, which also then sets
noprobe. Others seem to use just irq_set_noprobe().
Otherwise we can get:
drivers/pinctrl/pinctrl-single.c: In function 'pcs_irqdomain_map':
drivers/pinctrl/pinctrl-single.c:1750:2: error: implicit declaration of function 'set_irq_flags' [-Werror=implicit-function-declaration]
drivers/pinctrl/pinctrl-single.c:1750:21: error: 'IRQF_VALID' undeclared (first use in this function)
drivers/pinctrl/pinctrl-single.c:1750:34: error: 'IRQF_PROBE' undeclared (first use in this function)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpio interrupt controller on Rockchip socs can do edge triggers only
for single edges but not both. Nevertheless a lot of gpio users rely on
the availability of both-edge triggered interrupts - i.e. gpio-keys.
Therefore implement a solution similar to pinctrl-coh901 re-setting the
triggering edge depending on the gpio value in the interrupt demuxer.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Besides the pull registers sitting in a separate place, the rk3188 also
has the peculiarity that the pull registers of the first bank are split
and the first half is sitting in the register space of the pmu.
Therefore this adds a special bank-type for the first bank, to handle
the two register sources.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The check limiting bias options to supported ones is already
done thru rockchip_pinconf_pull_valid. Therefore this check is
redundant and can be removed.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are Rockchip SoCs, namely the rk3188, that combine a set of
regular banks with banks that need special handling for some settings.
Therefore add the possibility for the driver to handle more than one
bank type.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Further investigation of the different Rockchip SoCs showed that
the differences especially in the pull settings are quite deep.
As further patches will show, the register layout for the pulls of
the rk3188 is quite strange. Also it is to assume, that later
Rockchip SoCs may introduce even more quirks in this regard, making
it hard to support all of those using the current generic pull_*
variables.
Therefore move the driver to hold the type of controller in an enum
and do the handling according to it in the necessary places. Also
instead of calculating the register in the get and set pull functions
move it to a type-specific callback.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a typo which left twsi config3 option enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux driver of the Abilis Systems TB10x platform based on ARC700 CPUs.
Used to control the pinmux and is a prerequisite for the GPIO driver.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the infrastructure required to register non-linear gpio
ranges through gpiolib and the standard GPIO device tree bindings.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For omaps, we still have dependencies to the legacy code
for handling the PRM (Power Reset Management) interrupts,
and also for reconfiguring the io wake-up chain after
changes.
Let's pass the PRM interrupt and the rearm functions via
auxdata. Then when at some point we have a proper PRM
driver, we can get the interrupt via device tree and
set up the rearm function as exported function in the
PRM driver.
By using auxdata we can remove a dependency to the
wake-up events for converting omap3 to be device
tree only.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pin control registers can have interrupts for example
for device wake-up. These interrupts can be treated as a
chained interrupt controller as suggested earlier by
Linus Walleij <linus.walleij@linaro.org>.
This patch adds support for interrupts in a way that
should be pretty generic, and works for the omaps that
support wake-up interrupts. On omaps, there's an
interrupt enable and interrupt status bit for each pin.
The two pinctrl domains on omaps share a single interrupt
from the PRM chained interrupt handler. Support for
other similar hardware should be easy to add.
Note that this patch does not attempt to handle the
wake-up interrupts automatically unlike the earlier
patches. This patch allows the device drivers to do
a request_irq() on the wake-up pins as needed. I'll
try to do also a separate generic patch for handling
the wake-up events automatically.
Also note that as this patch makes the pinctrl-single
an irq controller, the current bindings need some
extra trickery to use interrupts from two different
interrupt controllers for the same driver. So it
might be worth waiting a little on the patches
enabling the wake-up interrupts from drivers as there
should be a generic way to handle it coming. And also
there's been discussion of interrupts-extended binding
for using interrupts from multiple interrupt controllers.
In any case, this patch should be ready to go allowing
handling the wake-up interrupts in a generic way, or
separately from the device drivers.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: linux-kernel@vger.kernel.org
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AS3722 is a compact system PMU suitable for mobile phones, tablets etc.
Add a driver to support accessing the GPIO, pinmux and pin configuration
of 8 GPIO pins found on the ams AS3722 through pin control driver and
gpiolib.
The driver will register itself as the pincontrol driver and gpio driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's replace is_pinconf with flags and add struct pcs_soc_data
so we can support SoC specific features like pin wake-up events.
Done in collaboration with Roger Quadros <rogerq@ti.com>.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO output value should be set after the GPIO interrupt is disabled.
Use BIT macro as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
[Edited commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also avoid use NULL pointer in error message.
v2-changes:
- use port pinter only after checking
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Palmas devices do not support the default bias configuration
and hence removing this option from valid pin config parameters.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dn and dp of USB1 can share with UART1(UART1 can route rx,tx to dn and dp pins of USB1).
here we add this pinmux capability.
USB1/UART1 mode selection has dedicated control register in RSC module, here we attach
the register offset of private data of related pin groups.
Signed-off-by: Rong Wang <Rong.Wang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
USP(Universal Serial Ports) can be UART as commit 5df831117b,
this patch defines the USP-based UART function pin groups for prima2.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent movement of all configurations of pin in the single call of
pin_config_set(), it is aborting configuration if BIAS_PULL_PIN_DEFAULT
is selected as return of configuration.
The original idea was to just avoid any update on register for pull up/down
configuration if this option is selected.
Fixing this by just bypassing any register update for BIAS_PULL_PIN_DEFAULT
and continuing the remaining configuration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Palmas pinmux and pin configuration support the single pin level
configuration in place of pin group.
Hence it is only require to pin_config_{set|get} and do not require
pin_config_group_{set|get}. As core framework already check for
require APIs availability, it is not require to implement as dummy
for non-require ops and so removing it.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Values of pins in table s5pv210 bank are incorrect. This patch correct values.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code hold port->lock spinlock and then try to grab the lock again
in adi_gpio_set_value(). Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace at91_mux_get_deglitch with at91_mux_pio3_get_deglitch when using
sam9x5 (pio3) IP.
at91_mux_get_deglitch only test the activation of the "Input Filter" which
may be overloaded by the activation of the "Input Filter Slow Clock" to use
the input filter as a debounce filter instead of a deglitch filter.
Fix at91_mux_pio3_get_debounce to test the activation of the Input Filter
before testing the activation of the debounce filter (Input Filter Slow
Clock depends on Input Filter).
Fix at91_mux_pio3_set_debounce function to avoid disabling the deglitch
filter ("Input Filter") when debounce filter is disabled.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are four I2C interfaces on r8a7790, each of them can be connected to
one of the two respective I2C controllers, e.g. interface #0 can be
configured to work with I2C0 or with IIC0. Additionally some of those
interfaces can also use one of several pin sets. Interface #3 is special,
because it can be used in automatic mode for DVFS. It only has one set
of pins available and those pins cannot be used for anything else, they
also lack the GPIO function.
This patch uses the sh-pfc ability to configure pins, not associated with
GPIOs and adds support for I2C3 to the r8a7790 PFC set up.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Adds pinmux for i2c bus 1 and 2. (Pins for 0 and 3 are not multiplexed.)
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
sizeof() is already size_t so there is no need to cast here. Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:
drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ADI GPIO2 controller was introduced since the BF548 and BF60x
processors. It differs a lot from the old one on BF5xx processors. So,
create a pinctrl driver under the pinctrl framework.
- Define gpio ports and pin interrupt controllers as individual platform
devices.
- Register a pinctrl driver for the whole GPIO ports and pin interrupt
devices.
- Probe pint devices before port devices. Put device instances into
the global gpio and pint lists.
- Define peripheral, irq and gpio reservation bit masks for each gpio
port as runtime resources.
- Save and restore gpio port and pint status MMRs in syscore PM functions.
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Get range by pinctrl_find_gpio_range_from_pin(), find gpio_port object
by container_of() and find adi_pinctrl by pin control device name.
- Handle peripheral and gpio requests in pinctrl operation functions.
- Demux gpio IRQs via the irq_domain created by each GPIO port.
v2-changes:
- Remove unlinke() directive.
v3-changes:
- Rename struct adi_pmx to adi_pinctrl.
- Fix the comments of struct gpio_pint.
- Remove unused pin_base in struct gpio_port.
- Change pint_assign into bool type.
- Add comments about the relationship between pint device and port device
to the driver header.
- Use BIT macro to shift bit.
- Remove all bitmap reservation help functions. Inline reservation functions
into the actual code.
- Remove gpio and offset mutual reference help functions.
- Remove all help functions to find gpio_port and adi_pinctrl structs. Get
range by pinctrl_find_gpio_range_from_pin(), find gpio_port object by
container_of() and find adi_pinctrl by pin control device name.
- Pass bool type usage variable to port_setup help function.
- Separate long bit operations into several lines and add comments.
- Use debugfs to output all GPIO request information.
- Avoid to set drvdata to NULL
- Add explanation to function adi_gpio_init_int()
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Remove the reference to pin control device from the gpio_port struct.
Remove the reference list to gpio device from the adi_pinctrl struct.
Replace the global adi_pinctrl list with adi_gpio_port_list. Walk through
the gpio list to do power suspend and resume operations.
- Remove the global GPIO base from struct adi_pinctrl, define pin base in
the platform data for each GPIO port device.
- Initialize adi_pinctrl_setup in arch_initcall().
- print the status of triggers, whether it is in GPIO mode, if it is
flagged to be used as IRQ, etc in adi_pin_dbg_show().
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.
v4-changes:
- remove useless system_state checking.
- replace dev_err with dev_warn in both irq and gpio pin cases.
- comment on relationship between irq type and invert operation.
- It is not necessary to check the reservation mode of the requested
pin in IRQ chip operation. Remove the reservation map.
- Use existing gpio/pinctrl subsystem debugfs files. Remove pinctrl-adi2
driver specific debugfs output.
- Add linkport group and function information for bf60x.
- Separate uart and ctsrts pins into 2 groups.
- Separate APAPI and alternative ATAPI pins into 2 groups.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver cannot be built as a module, so having a MODULE_ALIAS() isn't
useful.
While at it, fix a small typo in the file header comment and make the
module description string consistent with those for earlier Tegra SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
The valid offset range should be 0 ... chip->ngpio - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I forgot to drop the lock for the return inside the loop
protected by the spinlock in the pin config routine when
merging in -rc7 in commit 6ad30ce046
Reported-by: Sherman Yin <syin@broadcom.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It does not make sense to show ti prefix in pinconf_generic_dt_subnode_to_map()
dev_err messages.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSGqS5AAoJEHm+PkMAQRiGFxEH/3VrqF6WAkcviNiW/0DCdO8k
v6Wi7Sp5LxVkwzmOCHCV1tTHwLRlH3cB9YmJlGQ0kHCREaAuEQAB0xJXIW7dnyYj
Qq7KoRZEMe3wizmjEsj8qsrhfMLzHjBw67hBz2znwW/4P7YdgzwD7KRiEat+yRC9
ON3nNL2zIqpfk92RXvVrSVl4KMEM+WNbOfiffgBiEP24Ja1MJMFH1d4i6hNOaB0x
9Pb3Lw8let92x+8Ao5jnjKdKMgVsoZWbN/TgQR8zZOHM38AGGiDgk18vMz+L+hpS
jqfjckxj1m30jGq0qZ9ZbMZx3IGif4KccVr30MqNHJpwi6Q24qXvT3YfA3HkstM=
=nAab
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc7' into devel
Merged in this to avoid conflicts with the big locking fixes
from upstream.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Conflicts:
drivers/pinctrl/pinctrl-sunxi.c
Implement .request() and .free() callbacks on the GPIO chips to
inform pinctrl when a GPIO is requested or freed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In PIO_PUSR and PIO_PPDSR register if a given bit is set 1 this means the
pullup/down for this pin (pin is represented as a bit position) is
disabled.
Cc: stable <stable@vger.kernel.org> # 3.8+
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch implements pinctrl support and adds device tree bindings
for s5pv210.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include "linux/export.h" to avoid following warnings during compilation:
/***
pinctrl/pinctrl-utils.c:53:1: warning: data definition has no type or storage class [enabled by default]
pinctrl/pinctrl-utils.c:53:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
pinctrl/pinctrl-utils.c:53:1: warning: parameter names (without types) in function declaration [enabled by default]
pinctrl/pinctrl-utils.c:70:1: warning: data definition has no type or storage class [enabled by default]
pinctrl/pinctrl-utils.c:70:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
pinctrl/pinctrl-utils.c:70:1: warning: parameter names (without types) in function declaration [enabled by default]
pinctrl/pinctrl-utils.c:98:1: warning: data definition has no type or storage class [enabled by default]
pinctrl/pinctrl-utils.c:98:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
pinctrl/pinctrl-utils.c:98:1: warning: parameter names (without types) in function declaration [enabled by default]
pinctrl/pinctrl-utils.c:122:1: warning: data definition has no type or storage class [enabled by default]
pinctrl/pinctrl-utils.c:122:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
pinctrl/pinctrl-utils.c:122:1: warning: parameter names (without types) in function declaration [enabled by default]
pinctrl/pinctrl-utils.c:135:1: warning: data definition has no type or storage class [enabled by default]
pinctrl/pinctrl-utils.c:135:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
pinctrl/pinctrl-utils.c:135:1: warning: parameter names (without types) in function declaration [enabled by default]
**/
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If "irq == NUM_EINT" then it writes one space beyond the end of the
eint_data->domains[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We wanted to test "*map" here instead of "map".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The intent here was to test if the bit was set or not but there is a
logical vs bitwise AND typo so it is true if any bits are set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The resource mapped by of_iomap() isn't unmapped in error path. This
patch fix the resource leakage by using devm_ioremap_resource() instead
of of_iomap().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When setting pin configuration in the pinctrl framework, pin_config_set() or
pin_config_group_set() is called in a loop to set one configuration at a time
for the specified pin or group.
This patch 1) removes the loop and 2) changes the API to pass the whole pin
config array to the driver. It is now up to the driver to loop through the
configs. This allows the driver to potentially combine configs and reduce the
number of writes to pin config registers.
All c files changed have been build-tested to verify the change compiles and
that the corresponding .o is successfully generated.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the new devm_ioremap_resource() we can greatly simplify resource handling.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If (b->pin_base + b->nr_pins - 1) < pin is true, pin >= b->pin_base is always
true because b->nr_pins is never less than 0.
Thus this patch simplify the equation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a DT only driver and rockchip_pinctrl_dt_match is always compiled in.
Thus remove of_match_ptr macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix below build error if !PINMUX.
CC drivers/pinctrl/pinctrl-palmas.o
drivers/pinctrl/pinctrl-palmas.c:741:21: error: variable 'palmas_pinmux_ops' has initializer but incomplete type
drivers/pinctrl/pinctrl-palmas.c:742:2: error: unknown field 'get_functions_count' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:742:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:742:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:743:2: error: unknown field 'get_function_name' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:743:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:743:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:744:2: error: unknown field 'get_function_groups' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:744:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:744:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:745:2: error: unknown field 'enable' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:745:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:745:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
make[2]: *** [drivers/pinctrl/pinctrl-palmas.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This one is missed in commit 42fed7ba "pinctrl: move subsystem mutex to
pinctrl_dev struct".
I think this fixes the race between pin_free() and pin_request() calls.
It protects accessing the members of pctldev->desc.
(e.g. update desc->mux_usecount, desc->gpio_owner, desc->mux_owner, etc)
Current code grabs pctldev->mutex before calling pinmux_free_gpio(),
but did not grab the mutex while calling pinmux_request_gpio().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This became broken with converting the pinmux arrays into struct
types. While at it replace the preprocessor magic with a simple
dev_dbg.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just return once a match found makes the code simpler and shorter.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pin control utility functions provides the function for creating
map lists.
In place of implementing APIs locally in Tegra pin control driver
for creating map lists, use the utility functions. This reduces
the code size and avoid duplication.
Changes from V1:
- Rebased change on top of V1.
- Use pinctrl_utils_dt_free_map
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support to pass the config type like GROUP or PIN when using
the utils or generic pin configuration APIs. This will make the
APIs more generic.
Added additional inline APIs such that it can be use directly as
callback for the pinctrl_ops.
Changes from V1:
- Remove separate implementation for pins and group for
pinctrl_utils_dt_free_map and improve this function
to support both i.e. PINS and GROUPs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Calling pinctrl_register() means that the driver is fully initialized
and might accept pinmux/pinconf requests, so pin groups must be parsed
before.
This patch fixes this problem by moving device tree parsing before call
to pinctrl_register(). In addition, this fixes support for hogs on
pin controllers handled by pinctrl-samsung driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device family is called Palmas so there should be a 's' on the end of
the name.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The symbol SPEAr310_pinctrl_of_match does not exist at all. Fix it.
We didn't hit the compile error because this driver can only be built-in now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner A20 is pin-compatible with the older A10, so the two pin
set are quite similar. However, since the A20 has new features, we can't
just use the A10 pin set as is, and we need to define our own for the
A20.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner A31 SoC uses the same IP than the one found in the
A10/A13, with only different pins. Add the pins and the associated
functions found in the A31.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pin functions in the array were not indented like the other
functions in this array. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The implementation in pinctrl_register_one_pin() ensures pindesc->name is always
not NULL before insert the pindesc to radix tree.
If the desc return from pin_desc_get is not NULL, desc->name is always not NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hold pctldev->mutex mutex_lock when traverse the list.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This one is missed in commit 44d5f7bb "pinctrl: sink pinctrldev_list_mutex".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the old codes defined uart0_nostreamctrl_pins, but missed pingroup
and padmux definition for it. this patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The i.MX pinctrl driver uses 5 different arrays for storing the
informations for pins. This requires five allocations. Instead,
use a struct type which is more cache friendly, readable and
requires less allocations. One array of integers is still needed
since the pinctrl framework forces us to maintain it.
This also adds checks whether the allocations are succesful which
were missing.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When parsing a function fails this is no reason to make the whole
driver fail. Just continue with the next function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The i.MX pinctrl driver completely bails out when it detects an error
in the pinctrl nodes. This usually means that whatever error a
devicetree has the user is left blind because even the console cannot
be initialized without working pinmux.
Instead of bailing out completely, just continue probing. This makes
the pinctrl driver work, only the erroneous groups will fail later
during pin request time.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of crashing the kernel print an error message when
the fsl,pins property is missing.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When printing error messages about errors in the devicetree also print
the offending node to give the use a hint what might be wrong.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq flags variable gets a warning like this after
commit bf4dae5ce1
"pinctrl: nomadik: delete ancient pin control API":
In file included from include/linux/seqlock.h:29:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from
drivers/pinctrl/pinctrl-nomadik.c:14:
drivers/pinctrl/pinctrl-nomadik.c: In function 'nmk_pmx_enable':
include/linux/spinlock.h:348:122: warning:
'flags' may be used uninitialized in this function
[-Wmaybe-uninitialized]
raw_spin_unlock_irqrestore(&lock->rlock, flags);
^
drivers/pinctrl/pinctrl-nomadik.c:1515:16: note:
'flags' was declared here
unsigned long flags;
The function is question was never changed but it appears
the semantic checker could previously determine that the code
path that would use the flags was going to either use it or
not, but now it can't for some reason. Just fix it up.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We found out how to set the gphy led pinmuxing.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pps pin definition is missing in the current code.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Name the DU clock input 1 consistently with clock inputs 0 and 2.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Print out the affected group name on activation of pin mux
settings, and warn if you cannot free a pin that should have
been part of a certain setting.
ChangeLog v1->v2:
- Also print the pin name in the error messages.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TI Palmas series Power Management IC have multiple pins which can be
configured for different functionality. This pins can be configured
for different function. Also their properties like pull up/down,
open drain enable/disable are configurable.
Add support for pincontrol driver Palmas series device like TPS65913,
TPS80036. The driver supports to be register from DT only.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Add ack by Lee.
- Correct the binding docs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic APIs to map the DT node and its sub node in pinconf generic
driver. These APIs can be used from driver to parse the DT node who
uses the pinconf generic APIs for defining their nodes.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Rebased the pinctrl binding doc on top of Stephen's cleanup.
- Rename properties "pinctrl-pins" and "pinctrl-function" to
"pins" and "function".
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of pincontrol driver needs the utility function to create map
list. The utility function needed for adding mux, configs etc.
In place of duplicating this in each driver, add the common utility
function in common file and use from device specific driver. This will
reduce the duplicating of code across drivers.
Changes from V1:
- Add this files in this patch and add common utility APIs to here.
Changes from V2:
- Nothing in code.
- Added Reviewed by Stephen.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One peripheral may share part of its pins with the 2nd
peripheral and the other pins with the 3rd. If it requests all pins
when part of them has already be requested and owned by the 2nd
peripheral, this request fails and pinmux_disable_setting() is called.
The pinmux_disable_setting() frees all pins of the first peripheral
without checking if the pin is owned by itself or the 2nd, which
results in the malfunction of the 2nd peripheral driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin control subsystem was created to do away with custom pin
control APIs such as this one. It was kept for backward-compatibility
but is completely unused in the current kernel, so let's delete
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warning:
drivers/pinctrl/pinconf.c:521:20: error: incompatible types in comparison expression (different type sizes)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current implementation handle both edge and level interrupts with the
'handle_simple_irq' handler.
Level interrupts are active as long as the pin stays at the configured
level (low or high). In this case we have to use 'handle_level_irq' which
mask the interrupt until the handle has treated it.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The select input for some pin may not be implemented using the regular
select input register but the general purpose register. A real example
is that imx6q designers found the select input for USB OTG ID pin is
missing at the very late stage, and can not add a new select input
register but have to use a general purpose register bit to implement it.
The patch adds a workaround for such select input quirk by interpreting
the input_val cell of pin function ID in a different way, so that all
the info that needed for setting up select input bits in general purpose
register could be decoded from there.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
*map should be tested for NULL instead of map as kmalloc pointer
is assigned to it. This also fixes a potential null pointer dereference
bug later in the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
So, I notice that we get a couple of warnings from the pinctrl code:
drivers/pinctrl/pinconf.c: In function 'pinconf_dbg_config_print':
drivers/pinctrl/pinconf.c:433:36: warning: 'configs' may be used uninitialized in this function
drivers/pinctrl/pinconf.c: In function 'pinconf_dbg_config_write':
drivers/pinctrl/pinconf.c:511:36: warning: 'configs' may be used uninitialized in this function
While the compiler might not be able to work out that "configs" is
safe, the code doesn't lend itself very well to identifying that
fact when reading it either. This can be trivially solved by a slight
restructuring of the code - which also reduces the LOC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The correct header to include for clock handling is clk.h .
clk-provider.h should not be used in simple clock consumers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current code use no locking at all, which is obviously not that
great and can lead to concurrency issues, especially with the newer SMP
SoCs from Allwinner.
Add some locking where it's needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The current gpio_set function is ignoring the previous value set in the
GPIO value register, which leads in erasing the values already set for
the other GPIOs in the same bank when setting the value of a given GPIO.
Add the usual read/mask/write pattern to fix this brown paper bag bug.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The current irq_set_type code doesn't read the current register value
before writing to it, leading to the older programmed values being
overwritten and everything but the latest value being reset.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Navigating through the source code is hard enough without having to
manually search for groups and functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Update the pinmux configuration tables to support the TCLK1 pin.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SCIFA2 RXD_B and HRX0_C pins have their pinmux configuration data
swapped, fix it.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The pins have been removed from the datasheet, remove them here as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The pins have been removed from the datasheet, remove them here as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The pins have been removed from the datasheet, remove them here as well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The RTS/CTS pins have been renamed in the datasheet, rename them here as
well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The I2C pins have been renamed in the datasheet, rename them here as
well.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add all I2C pin groups to R8A7779 PFC driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The macros expand to irq_pin() calls and where most probably introduced
from a copy&paste of the sh7372 PFC data. Replace them with irq_pin().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
The mach/irqs.h header is included only to get the evt2irq macro
definition. The macro is defined in linux/sh_intc.h, include it directly
instead of the mach-specific header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
The SoC-specific mach/<soc>.h headers are included needlesly. Don't
include them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Pins with selectable functions but without a GPIO port can't be named
PORT_# or GP_#_#. Add a SH_PFC_PIN_NAMED macro to declare such pins in
the pinmux pins array, naming them with the PIN_ prefix followed by the
pin physical position.
In order to make sure not to register those pins as GPIOs, add a
SH_PFC_PIN_CFG_NO_GPIO pin flag to denote pins without a GPIO port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Remove the manually specified ranges from PFC SoC data and compute the
ranges automatically. This prevents ranges from being out-of-sync with
pins definitions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The field contains the number of pins with an associated GPIO port. This
is currently equal to the total number of pins but will be modified when
adding support for pins without a GPIO port. Rename the field
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The pin number is usually equal to the GPIO number but can differ when
GPIO numbering is sparse.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The PORT_1 macro invokes a macro passed as a parameter. Pass the pin
number down to that macro at the bottom of the call stack. This will be
used to compute the pin ranges automatically.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Pass down the port number down to the PORT_1 macro. The port number will
be used to compute the pin ranges automatically.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The PINMUX_GPIO macro takes a port name and a data mark, respectively of
the form GPIO_name and name_DATA. Modify the macro to take the name as a
single argument and derive the port name and data mark from it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Unlike all other PFC SoC data, the shx3 data prefix all static symbols
with shx3_. Remove the prefix to be consistent with the other source
files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SoC has a bank-style PFC. Replace the custom-defined macros with
common macros from sh-pfc.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Move the pin definition macros to a common header file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Move macros defined in several SoC data files to a common location and
document them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The gpio_get_data_reg() and gpio_setup_data_reg() functions both take an
argument named gpio. The argument contains a GPIO offset for the first
function and a pin index for the second one. Rename them to offset and
idx respectively to match the rest of the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The typedef only conceals the real variable type without bringing any
additional value (see Documentation/CodingStyle, section 5.b). Moreover,
it polutes the pinmux namespace. Replace it with the integer type it
used to hide.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The GPIO driver uses an array of sh_pfc_gpio_pin structures to store
per-GPIO pin data. The array size is miscomputed at allocation time by
using the number of the last pin instead of the number of pins. When the
pin space contains holes this leads to memory overallocation. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The macro isn't used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Two integer field structures are needlesly defined as const. Remove the
const keyword.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The SH_PFC_MARK_INVALID macro and the PINMUX_FLAG_TYPE, GPIO_CFG_REQ and
GPIO_CFG_FREE enum entries are used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Most of the PORT_DATA_* macros are not used, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The ranges are not used anymore, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
The PFC SHX3 SoC data contains a input_pu range used to configure
pull-up resistors using the legacy non-pinconf API. That API has been
removed from the driver, the range is thus not used anymore. Remove it.
If required, configuring pull-up resistors for the SHX3 can be
implemented using the pinconf API, as done for the SH-Mobile, R-Mobile
and R-Car platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The PFC SH7786 SoC data contains a input_pu range used to configure
pull-up resistors using the legacy non-pinconf API. That API has been
removed from the driver, the range is thus not used anymore. Remove it.
If required, configuring pull-up resistors for the SH7786 can be
implemented using the pinconf API, as done for the SH-Mobile, R-Mobile
and R-Car platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
