Implement the ->restore() PM operation and set the link to off, which will
force a full reset and restore. This ensures that Host Performance Booster
is reset after suspend-to-disk.
The Host Performance Booster feature caches logical-to-physical mapping
information in the host memory. After suspend-to-disk, such information is
not valid, so a full reset and restore is needed.
A full reset and restore is done if the SPM level is 5 or 6, but not for
other SPM levels, so this change fixes those cases.
A full reset and restore also restores base address registers, so that code
is removed.
Link: https://lore.kernel.org/r/20211018151004.284200-2-adrian.hunter@intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sgl is freed in the target stack in target_release_cmd_kref() before
calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that
causes a panic if sgl is not yet DMA unmapped:
NIP dma_direct_unmap_sg+0xdc/0x180
LR dma_direct_unmap_sg+0xc8/0x180
Call Trace:
ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable)
dma_unmap_sg_attrs+0x54/0xf0
qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx]
qlt_free_cmd+0x124/0x1d0 [qla2xxx]
tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx]
target_put_sess_cmd+0x198/0x370 [target_core_mod]
transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod]
tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx]
The sgl may be left unmapped in error cases of response sending. For
instance, qlt_rdy_to_xfer() maps sgl and exits when session is being
deleted keeping the sgl mapped.
This patch removes use-after-free of the sgl and ensures that the sgl is
unmapped for any command that was not sent to firmware.
Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 8c0eb596ba ("[SCSI] qla2xxx: Fix a memory leak in an error path of
qla2x00_process_els()"), intended to change:
bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN
to:
bsg_job->request->msgcode != FC_BSG_RPT_ELS
but changed it to:
bsg_job->request->msgcode == FC_BSG_RPT_ELS
instead.
Change the == to a != to avoid leaking the fcport structure or freeing
unallocated memory.
Link: https://lore.kernel.org/r/20211012191834.90306-2-jgu@purestorage.com
Fixes: 8c0eb596ba ("[SCSI] qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Joy Gu <jgu@purestorage.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit 9e67600ed6 ("scsi: iscsi: Fix race condition between login and
sync thread") we meant to add a check where before we call ->set_param() we
make sure the iscsi_cls_connection is bound. The problem is that between
versions 4 and 5 of the patch the deletion of the unchecked set_param()
call was dropped so we ended up with 2 calls. As a result we can still hit
a crash where we access the unbound connection on the first call.
This patch removes that first call.
Fixes: 9e67600ed6 ("scsi: iscsi: Fix race condition between login and sync thread")
Link: https://lore.kernel.org/r/20211010161904.60471-1-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Li Feng <fengli@smartx.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit d39df15851 ("scsi: iscsi: Have abort handler get ref to conn")
added iscsi_get_conn()/iscsi_put_conn() calls during abort handling but
then also changed the handling of the case where we detect an already
completed task where we now end up doing a goto to the common put/cleanup
code. This results in a iscsi_task use after free, because the common
cleanup code will do a put on the iscsi_task.
This reverts the goto and moves the iscsi_get_conn() to after we've checked
if the iscsi_task is valid.
Link: https://lore.kernel.org/r/20211004210608.9962-1-michael.christie@oracle.com
Fixes: d39df15851 ("scsi: iscsi: Have abort handler get ref to conn")
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an FC-GS I/O is aborted by lpfc, the driver requires a node pointer
for a dereference operation. In the abort I/O routine, the driver miscasts
a context pointer to the wrong data type and overwrites a single byte
outside of the allocated space. This miscast is done in the abort I/O
function handler because the handler works on both FC-GS and FC-LS
commands. However, the code neglected to get the correct job location for
the node.
Fix this by acquiring the necessary node pointer from the correct job
structure depending on the I/O type.
Link: https://lore.kernel.org/r/20211004231210.35524-1-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS driver uses blk_mq_tagset_busy_iter() when identifying task
management requests to complete, however blk_mq_tagset_busy_iter() doesn't
work.
blk_mq_tagset_busy_iter() only iterates requests dispatched by the block
layer. That appears as if it might have started since commit 37f4a24c24
("blk-mq: centralise related handling into blk_mq_get_driver_tag") which
removed 'data->hctx->tags->rqs[rq->tag] = rq' from blk_mq_rq_ctx_init()
which gets called:
blk_get_request
blk_mq_alloc_request
__blk_mq_alloc_request
blk_mq_rq_ctx_init
Since UFS task management requests are not dispatched by the block layer,
hctx->tags->rqs[rq->tag] remains NULL, and since blk_mq_tagset_busy_iter()
relies on finding requests using hctx->tags->rqs[rq->tag], UFS task
management requests are never found by blk_mq_tagset_busy_iter().
By using blk_mq_tagset_busy_iter(), the UFS driver was relying on internal
details of the block layer, which was fragile and subsequently got
broken. Fix by removing the use of blk_mq_tagset_busy_iter() and having the
driver keep track of task management requests.
Link: https://lore.kernel.org/r/20210922091059.4040-1-adrian.hunter@intel.com
Fixes: 1235fc569e ("scsi: ufs: core: Fix task management request completion timeout")
Fixes: 69a6c269c0 ("scsi: ufs: Use blk_{get,put}_request() to allocate and free TMFs")
Cc: stable@vger.kernel.org
Tested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 756fb6a895 ("scsi: acornscsi: Remove tagged queuing vestiges")
mistakenly introduced a reference to function scsi_cmd_to_tag(). This
function does not exist as it was removed from an earlier series version
when I upstreamed the named commit - originally authored By Hannes - but
this reference still remained.
Fix by replacing the reference to scsi_cmd_to_tag() with
scsi_cmd_to_rq(scsi_scmd)->tag, which scsi_cmd_to_tag() was a wrapper for.
Link: https://lore.kernel.org/r/1633002717-79765-1-git-send-email-john.garry@huawei.com
Fixes: 756fb6a895 ("scsi: acornscsi: Remove tagged queuing vestiges")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update TCP silly-window-syndrome timeout, for the cases where
initiator's small TCP window size prevents FW from transmitting
packets on the connection. Timeout causes FW to retransmit
window probes if needed, preventing I/O stall if initiator ignores
first window probe.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nikolay Assa <nassa@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing qed/qede/qedr/qedi/qedf code uses chip-specific naming in
structures, functions, variables and defines in FW HSI (Hardware
Software Interface).
The new FW version introduced a generic naming convention in HSI
in-which the same code will be used across different versions
for simpler maintainability. It also eases in providing support for
new features.
With this patch every "_e4" or "e4_" prefix or suffix is not needed
anymore and it will be removed.
Reviewed-by: Manish Rangankar <mrangankar@marvell.com>
Reviewed-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Omkar Kulkarni <okulkarni@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both cxgb4 and csiostor drivers run on their own independent Physical
Function. But when cxgb4 and csiostor are both being loaded in parallel via
modprobe, there is a race when firmware upgrade is attempted by both the
drivers.
When the cxgb4 driver initiates the firmware upgrade, it halts the firmware
and the chip until upgrade is complete. When the csiostor driver is coming
up in parallel, the firmware mailbox communication fails with timeouts and
the csiostor driver probe fails.
Add a module soft dependency on cxgb4 driver to ensure loading csiostor
triggers cxgb4 to load first when available to avoid the firmware upgrade
race.
Link: https://lore.kernel.org/r/1632759248-15382-1-git-send-email-rahul.lakkireddy@chelsio.com
Fixes: a3667aaed5 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
devlink is a software interface that doesn't depend on any hardware
capabilities. The failure in SW means memory issues, wrong parameters,
programmer error e.t.c.
Like any other such interface in the kernel, the returned status of
devlink APIs should be checked and propagated further and not ignored.
Fixes: 755f982bb1 ("qed/qede: make devlink survive recovery")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting SCSI logging level with error=3, we saw some errors from enclosues:
[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13
Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).
Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Reviewed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I fixed a stringop-overread warning earlier this year, now a second copy of
the original code was added and the warning came back:
drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_cmf_info_show':
drivers/scsi/lpfc/lpfc_attr.c:289:25: error: 'strnlen' specified bound 4095 exceeds source size 24 [-Werror=stringop-overread]
289 | strnlen(LPFC_INFO_MORE_STR, PAGE_SIZE - 1),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it the same way as the other copy.
Link: https://lore.kernel.org/r/20210920095628.1191676-1-arnd@kernel.org
Fixes: ada48ba70f ("scsi: lpfc: Fix gcc -Wstringop-overread warning")
Fixes: 74a7baa2a3 ("scsi: lpfc: Add cmf_info sysfs entry")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The acornscsi driver has a config option to enable tagged queuing, but this
option gets disabled in the driver itself with the comment 'needs to be
debugged'. As this is a _really_ old driver I doubt anyone will be wanting
to invest time here, so remove the tagged queue vestiges and make our lives
easier.
[jpg: Use scsi_cmd_to_rq()]
Link: https://lore.kernel.org/r/1631696835-136198-3-git-send-email-john.garry@huawei.com
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit a113eaaf86.
There are a couple of issues with the commit:
1. It causes deadlocks.
2. It causes the shost->eh_cmd_q list of failed requests not to be
processed, ever.
So revert it.
1. Deadlocks
The SCSI error handler runs with requests blocked beginning when
scsi_schedule_eh() sets SHOST_RECOVERY state, continuing through
scsi_error_handler() callback ->eh_strategy_handler() until
scsi_restart_operations() is called. By setting eh_strategy_handler to
ufshcd_err_handler, the patch changed the UFS error handler to run with
requests blocked, including PM requests, for the entire run of the error
handler.
That conflicts with UFS error handler existing synchronization with UFS
device PM operations. The UFS error handler synchronizes with runtime PM
by doing pm_runtime_get_sync() prior to blocking requests itself. It
synchronizes with system PM by use of hba->host_sem, again before blocking
requests itself. However, if requests are already blocked, then PM
operations will block. So:
the UFS error handler blocks waiting on PM
+ PM blocks waiting on SCSI PM requests to process or fail
+ PM requests are blocked waiting on error handling to finish
= deadlock
This happens both for runtime PM and system PM.
Prior to the patch, these deadlocks could not happen even if SCSI error
handling was running, because the presence of requests in shost->eh_cmd_q
would mean the queues could not be suspended, which would mean that, should
the UFS error handler run at the same time, it would not need to wait for
PM or vice versa.
Please note these scenarios are not just theoretical, they were found
during testing on a Samsung Galaxy Book S.
2. ->eh_strategy_handler() must process shost->eh_cmd_q list of failed
requests, as all other eh_strategy_handler's do except UFS error handler.
Refer for example: scsi_unjam_host(), ata_scsi_error() and
sas_scsi_recover_host().
Link: https://lore.kernel.org/r/20210917144349.14058-1-adrian.hunter@intel.com
Fixes: a113eaaf86 ("scsi: ufs: Synchronize SCSI and UFS error handling")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sd_spinup_disk() is a little bit noisy after commit 848ade90ba ("scsi:
sd: Do not exit sd_spinup_disk() quietly"):
scsi 0:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] Media removed, stopped polling
sd 0:0:0:0: [sda] Media removed, stopped polling
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: [sda] Media removed, stopped polling
There's not really a benefit in printing the same message multiple
times. Therefore print it only if media_present was previously set.
Link: https://lore.kernel.org/r/a2d0a249-6035-9697-626a-e14ec50ef6ee@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch checker reported the following error:
drivers/base/power/sysfs.c:833 dpm_sysfs_remove()
warn: sleeping in atomic context
With a calling sequence of:
efct_lio_npiv_drop_nport() <- disables preempt
-> fc_vport_terminate()
-> device_del()
-> dpm_sysfs_remove()
Issue is efct_lio_npiv_drop_nport() is making the fc_vport_terminate() call
while holding a lock w/ ipl raised.
It is unnecessary to hold the lock over this call, shift where the lock is
taken.
Link: https://lore.kernel.org/r/20210907165225.10821-1-jsmart2021@gmail.com
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Co-developed-by: Ram Vegesna <ram.vegesna@broadcom.com>
Signed-off-by: Ram Vegesna <ram.vegesna@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reporting zones on a SCSI device sometimes fail with the following error:
[76248.516390] ata16.00: invalid transfer count 131328
[76248.523618] sd 15:0:0:0: [sda] REPORT ZONES start lba 536870912 failed
The error (from drivers/ata/libata-scsi.c:ata_scsi_zbc_in_xlat()) indicates
that buffer size is not aligned to SECTOR_SIZE.
This happens when the __vmalloc() failed. Consider we are reporting 4096
zones, then we will have "bufsize = roundup((4096 + 1) * 64,
SECTOR_SIZE)" = (513 * 512) = 262656. Then, __vmalloc() failure halves
the bufsize to 131328, which is no longer aligned to SECTOR_SIZE.
Use rounddown() to ensure the size is always aligned to SECTOR_SIZE and fix
the comment as well.
Link: https://lore.kernel.org/r/20210906140642.2267569-1-naohiro.aota@wdc.com
Fixes: 23a50861ad ("scsi: sd_zbc: Cleanup sd_zbc_alloc_report_buffer()")
Cc: stable@vger.kernel.org # 5.5+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
