Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A purely cosmetic change. Report which physical layer is present, instead
of PHY unknown. 82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.
This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.
This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCA is undefined then the adapter struct becomes unnecessary. To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24. It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().
Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.
This prevents driver from getting right mac addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.
Problem Description:
As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.
Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).
Problem Solution:
The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g . 10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel). The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv643xx_eth_open() is called to up an interface, port_start()
will first re-program the unicast address filter, and then
re-initialise the PORT_CONFIG register, but that will disable unicast
promiscuous mode if it was enabled by the unicast address filter setup.
This isn't a problem on ifconfig up, as ->set_rx_mode() will be called
shortly afterwards which will program the filters again, but it does
trigger when changing the MTU, which calls mv643xx_eth_stop() and then
mv643xx_eth_open() by hand to repopulate the receive rings with skbuffs
of the new size.
Swap the initialisation of the PORT_START register and the call to
the unicast filter setup function to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original patch was submitted last year but wasn't discussed or applied
because of missing maintainer's CCs. I only fixed some formatting errors,
but as I saw tulip is very badly formatted and needs further work.
Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We
should allow receiving frames of up to 1518 bytes in length, instead of
1514.
Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived
at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.
Tested on D-Link DFE-570TX quad-fastethernet card.
Signed-off-by: Tomasz Lemiech <szpajder@staszic.waw.pl>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the circular locking problem by changing the locking strategy
concerning the logging of firmware handles.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC variant in the 405EX and 405EXr chips needs the "440EP" type clock
control workaround to avoid lockups of the Rx side during reset.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Dave Jones <davej@redhat.com>
The dma-debug changes caught that this driver uses the
wrong DMA mapping length when skb_padto() does something.
With suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the mac address when a macvlan device is up will leave the
device on the wrong hash chain making it impossible to receive
packets.
There is no checking of the mac address set on the macvlan. Allowing
a misconfiguration to grab packets from the the underlying device or
another macvlan.
To resolve these problems I update the hash table of macvlans when the
mac address of a macvlan changes, and when updating the hash table
I verify that the new mac address is usable.
The result is well defined and predictable if not perfect handling of
mac vlan mac addresses.
To keep the code clear I have created a set of hash table maintenance
in macvlan so I am not open coding the hash function and the logic
needed to update the hash table all over the place.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in a network namespace whose only link to
the outside world is a macvlan device, not being
able to create another macvlan is a real pain.
So modify macvlan creation to allow automatically forward
a creation of a macvlan on a macvlan to become a creation
of a macvlan on the underlying network device.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch from Juha Leppanen suppresses a false warning if the eeprom
load succeeds on the very last attempt.
Juha> In function smsc911x_open smsc911x_reg_read+udelay can be run 50
Juha> times with timeout reaching -1, and the following if statetement
Juha> does not catch the timeout and no warning is issued. Also if the
Juha> 50th smsc911x_reg_read is GOOD, loop is exited with timeout as 0
Juha> and bogus warning issued. Replace testing order and --timeout
Juha> instead of timeout-- and now max 50 smsc911x_reg_read's are done,
Juha> with max 49 udelays.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch from Juha Leppanen suppresses a false warning if a fast
forward operation succeeds on the very last attempt.
Juha> If smsc911x_reg_read loop is executed 500 times, timeout reaches 0
Juha> and the 500th smsc911x_reg_read result in val is ignored. If
Juha> testing order is changed, then val is checked first. The 500th
Juha> reg_read might be GOOD, why ignore it!
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1577ecef76
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Feb 4 16:42:12 2009 -0800
netdev: Merge UCC and gianfar MDIO bus drivers
left out the deletion of gianfar_mii.c.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar patch as for 8139cp posted yesterday, so the same comment:
So far there was not a chance to set a mac address on running 8139too device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far there was not a chance to set a mac address on running 8139cp device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently ignores the local or remote link faults
raised at the mac layer. This patch fixes it.
Our mac however only advertizes link events, so wait for the
phy to stabilize the link, then enable mac link events interrupts.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the heurstics workaround unlocking a hung mac:
- reduce Tx mac toggling by enabling Tx drain before resetting the mac
- Take Tx (lack of) activity in account only
- Update the monitoring counter range to 64 bits
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under RX pressure, The HW might generate a high load of interrupts
to signal mac fifo or free lists overflow.
Disable the interrupts, and poll the relevant status bits
to maintain stats.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate TX and RX reclaim handlers
Don't disable interrupts in RX reclaim handler.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Elmininate a cache miss when accessing the CPL header within
the first aggregated buffer.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update skb truesize correctly for the 2nd buffer from a Jumbo frame
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release page chunk reference in case we fail to map it.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ring free lists door bell less frequently,
specifically every quarter of the active FL
size.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*netif_rx_* functions is obsolete and removed in newer kernels so
we need to use corresponding *napi_* functions instead.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE
FPGA. Heavily based on Dave sources, I've just adopted it to current
kernel version and done some code cleanup.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix printk format warnings:
drivers/net/wimax/i2400m/netdev.c:523: warning: format '%zu' expects type 'size_t', but argument 7 has type 'unsigned int'
drivers/net/wimax/i2400m/netdev.c:548: warning: format '%zu' expects type 'size_t', but argument 7 has type 'unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same operation is performed when the Ethernet driver initializes
the port.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch clears the irqstatus register with the exact same events it
has read from it. Since the read-write operation is not atomic, a new
irqstatus bit could have been set in between these operations and would
then be cleared accidentally.
Secondly, we now don't need any spin lock protection when
scheduling/completing napi poll as the isr will not execute anymore (as
we turn off all interrupts now).
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the throughput mode poll settings to reduce the
number of interrupts. This is only used by older hardware that need a
timer irq in throughput mode.
Secondly, this patch increases the default rx ring from 128 to 512. This
drastically improves bandwidth utilization for small packets sizes i.e
512 bytes.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the logic to moderate the interrupts by changing the
mode between throughput and poll. If there has been a large amount of
time without any burst of network load, the code will transition to pure
throughput mode (where each tx/rx/other will cause an interrupt). If
bursts of network load occurs, it will transition to poll based mode to
help reduce cpu utilization (it will not interrupt on each packet) while
maintaining the optimum network bandwidth utilization.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is only a subset of changes so that it is easier to see the
modifications. This patch removes the isr 'for' loop and shifts all the
logic to account for new tab spacing.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new optimization mode called Dynamic has been added. This will be mode
where interrupt moderation logic will dynamically switch between pure
throughput mode and poll based (called 'cpu') mode.
Also, for newer chipsets, the timer irq is not needed for throughput
mode. Secondly, since we are modifying the irqmask to change between
modes, msix is not supported.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi poll routine has been modified to handle all interrupt events
and process them accordingly. Therefore, the ISR will now only schedule
the napi poll and disable all interrupts instead of just disabling rx
interrupt.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two tx_done routines to handle tx completion processing. Both
these functions now take in a limit value and return the amount of tx
completions. This will be used by a future patch to determine the total
amount of work done.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary overhead code. Firstly, there is no nead
to mask off unwanted interrupts as we will be checking against the
irqmask field anyways. Secondly, there has been no value in last few
years from detecting error or unknown interrupts.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will save the irq events in the driver's context so that the
napi routine knows which interrupts have occurred. Subsequent changes
will be moving all interrupt processing into the napi poll routine.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes support for msix running in conjunction with napi.
There has been reported issues regarding the behaviour of irqmask and
generation of interrupts by the HW when in MSIX mode. When running napi,
the driver is constantly turning off/on the irqmask. For the time being,
I am going to disable it until I can root cause the issue.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing napi enable/disable calls.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the stats feature would not encompass all older
versions. This would result in only retreiving a subset of all available
stats in HW.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocols that use packet_type can be __read_mostly section for better
locality. Elminate any unnecessary initializations of NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove huge board config structure from each instance, read
only necessary fields from flash.
Replace board_type with port_type (1G/10G), there's another
board_type field describing card type (SFP/XFP/CX4).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_RCV_CTX was set to 1, there's only rx context per
PCI function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rearrange open and close into hardware attach(), detach() and
nic up() and down(). this will be used for suspend/resume
subsequently.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unused rx fragment handling code.
o imporove check for status descriptor ownership.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a bug, which occasionally caused failure in PRAM initialization after
the cold boot.
Also incremented version number to 1.45.27.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a proper cast to the argument of PAGE_ALIGN macro so that the output
won't depend on its original type. Without this cast aligned value will be
truncated to the size of the argument type.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sge_buff_size may not be more than 0xffff.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Tested-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in an earlier net-next patch.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The completion interrupt disable routine is only called from the ISR, so
there is no need for irqsave/restore.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of extraneous ql_cycle_adapter. It's only called from the one
place.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a number of race conditions in the driver.
Up until now, "entry" pointer was initialized before acquiring the right lock.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes compilation, if the PCI core is disabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs ath9k/phy#/wiphy can be used to show the current list of
virtual wiphys and to add/remove virtual wiphys. Eventually, this
interface could be replaced with a cfg80211/nl80211 command that is
passed through mac80211.
For example:
# cat /debug/ath9k/phy0/wiphy
primary: phy0
# echo add > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
secondary: phy1
# echo del=phy1 > /debug/ath9k/phy0/wiphy
# cat /debug/ath9k/phy0/wiphy
primary: phy0
In addition, following commands can be used to test pausing and
unpausing of the virtual wiphys:
pause=phy1
unpause=phy1
select=phy1
(select pauses and unpauses wiphys automatically based on channel)
schedule=500
(set wiphy scheduling interval in msec; 0 = disable; default value: 500)
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a very simple scheduler that goes through the wiphys and
schedules one at a time every N milliseconds (current default value:
500 ms). This is enough for initial testing, but there are number of
areas where a more complex scheduler can improve operations greatly.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow mac80211-controlled channel changes on an active wiphy and
especially during a scan. We need this as long as the scan is
controlled by mac80211. Moving this control into the driver could
allow some optimizations on scanning while using multiple virtual
interfaces, but for now, try to work as well as possible with the
current scan mechanism.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like channel change may fail in some cases and end up leaving
the hardware in state where it cannot transmit any frames. Add a
workaround to recover from this state if we detect that wiphy
selection is failing due to wiphys not leaving PAUSING state.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should not be requesting us to transmit frames on paused
wiphys since we stop the TX queues. Just in case, add debug code to
make sure we catch if this were to happen.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, allow channel changes immediately and just force the other
virtual wiphys to paused state. This is needed to allow
mac80211-controlled scan to control channel changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify the AP that we may be sleeping longer to allow the AP power
save code to buffer larger number of frames for us when using virtual
wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always going through initialization/deinitialization steps,
do this only for the first/last wiphy to not break the other wiphys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_wiphy_select() can be used to select a virtual wiphy to be
activated. Other virtual wiphys will be paused and once that is done,
the operational channel is changed and the wiphys that are on the
selected channel will be unpaused.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow virtual wiphys to be paused/unpaused to allow off-channel
operations. Pause will stop all TX queues for the wiphy and move the
STA into power save mode if in managed mode. Unpause wakes up the TX
queues and notifies the AP that the STA woke up if in managed mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow RX filter to pass through all broadcast/multicast frames (i.e.,
no BSSID filtering) if virtual interfaces are used. Software filtering
will be used in this case to drop broadcast/multicast frames for
foreign BSSIDs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new struct ath_softc::sec_wiphy array is used to store information
about virtual wiphys and select which wiphy is used in calls to
mac80211. Each virtual wiphy will be assigned a different MAC address
based on the virtual wiphy index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the initial step in allowing ath9k to register multiple
virtual radios (wiphys). The goal of virtual radios is to allow the
same radio to be shared for multiple virtual interfaces that may
operate on different channels. The mac80211 virtual interface support
is designed only for single channel operation and as such, it is not
suitable for this type of use. Anyway, it can be used on top of the
virtual radio concept, if desired (e.g., use two virtual radios to
handle two channels and then add multiple mac80211 virtual interfaces
on top of each virtual radio).
The new struct ath_wiphy is now registered as the driver data
structure for wiphy. This structure has a pointer to the shared (among
virtual wiphys of the same physical radio) struct ath_softc data. The
primary wiphy maintains the allocated memory for ath_softc. Secondary
(virtual) wiphys will only allocate the new ath_wiphy structure.
Registration of secondary wiphys is added in a separate patch.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded BSSID mask (mask for own addresses),
iterate through all active interfaces and determine the minimal mask
that covers all local addresses.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the internal sc_vaps array and index values by using vif
pointer from mac80211. Allow multiple VIPs to be registered. Though,
number of beaconing VIFs is still limited by ATH_BCBUF (currently
1). Multiple virtual STAs support is not yet complete, but at least
the data structures should now be able to handle this.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By exporting the register base, and word size to userspace
through debugfs it will be easier to create scripts which
parse the register information. This makes debugging and
register dumps information easier.
This will break my previous scripts which dumped and parsed
all information, but since this is only for debugging purposes
this change should not be a problem.
Dumpfiles created with the old version can be easily manually
edited to make them compatible with this new approach, which
means there will be no problems comparing dumps from the
different versions either.
Also be more consistent with using tabs to seperate different
fields.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use ath_keyset() wrapper for
ath9k_hw_set_keycache_entry() calls. In addition, improve the comments
describing the key setting operations.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current bitmask is invalid, because the tx dma size is a 3 bit wide
value.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't store the beacon timestamp internally, nor
do we do any TIM handling in ath9k.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TSF has to be reset only once, upon bringing
the interface up in AP mode. For any beacon reconfigure calls
after that, resetting the TSF results in incorrect beacon generation.
The only exception is a change in the beacon interval,
which is indicated to the driver by mac80211 through
IEEE80211_CONF_CHANGE_BEACON_INTERVAL, handle this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the code easier to understand.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use SC_OP_NO_RESET, it is not configurable at all.
Remove all code that deals with this flag and make beacon
stuck processing simple.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove useless comments, fix indentation.
Also, remove all occurrences of ASSERT(vif) which are not needed.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only use case for this right now is ANI calibration,
but more might come up in the future.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old code doesn't work correctly e.g. on newer chipsets like AR5418+AR2122 and AR5416+AR2133.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the RX handler to pass more status flags to mac80211.
It also changes part of the drop policy, if bad frames were requested. (Note that
currently mac80211 will throw a WARN_ON in that case. But nothing bad will happen).
This also removes some obsolete unused timestamping code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So that a new created IBSS network
doesn't break on the first scan.
It seems to Sujith and me that this
stupid code unnecessary, too.
So remove it...
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore network sleep mode in isr if power save is enabled.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This callback can be used to handle dynamic 20/40,
and changes in the operating channel's HT parameters.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used anywhere in ath9k and is just making the code more
confusing.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are number of small details about the keycache operations that
are very easy to miss (and forget), so better include detailed
comments in ath9k_hw_set_keycache_entry() to avoid having to figure
out this every time when having to touch this area.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce stack memory footprint of iwlwifi.
(From >1000 bytes for each *_table_read
on i386 down to 32)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Software antenna tuning is broken because of an function
ordering problem during rt2x00link_tuner().
rt2x00link_precalculate_signal()
rt2x00leds_led_quality()
rt2x00lib_antenna_diversity()
rt2x00link_precalculate_signal() will reset the quality TX/RX counters,
however rt2x00lib_antenna_diversity() requires the RX counter to
see what RSSI value must be used for a particular antenna.
We can't change the ordering since rt2x00lib_antenna_diversity() might
reset other statistics which are needed by the function called earlier.
Move the reset of the quality TX/RX counters into a seperate function
and move the call to after rt2x00lib_antenna_diversity().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_activate_qos instead of iwl3945_activate_qos.
Patch does two things
1) Patch adds iwl_activate_qos in core library.
2) 3945 makes use of iwl_activate_qos.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch does following,
1) mac80211's shared data is now initialized in iwl3945_setup_mac.
2) Set the rfkill to right state after initialization
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for iwlagn:
- Have to free eeprom of version check fails - otherwise we end up with
memory leak.
- Include removal of workqueue (created in _setup_deferred_work) in error
handling.
for iwl3945:
- Fix a few places to jump to correct error handling.
- Reorganize error handling to match with code flow.
- Include iwl_free_channel_map as part of error handling.
- Include releasing eeprom as part of error handling.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
unify the set key flow with iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS, TSF maintains local clock counters at each station. Network
Synchronization follows a completely distributed scheme where beacon frames
are generated. Each station maintain its own TSF timestamp, extracted from
beacon timestamps they recieved. Following patch synchronize this beacon timestamp
with uCode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure we print out a warning when the index is out of bounds,
i.e. even on hw_rix == AR5K_MAX_RATES.
Also change to WARN and print text with the reported hw_rix.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect Michael MIC key (RX, should have been TX) was set for the
group key in AP mode. This resulted in all broadcast frames triggering
Michael MIC errors and eventual TKIP countermeasures. The change here
sets the correct Michael MIC key based on whether the local end is the
authenticator (well, AP for now).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Applying kernel janitors todos (reduce stack
footprint where possible) to airo wireless driver.
(Before 1124 bytes on i386, now 876)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin can reach -1 after the loop, so 0 is still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements get_tsf() of ieee80211_ops in the zd1211rw driver.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nohwcrypt=1 module parameter can now be used to disable hardware
crypto in ath9k. While the hardware acceleration handles most cases,
it may be useful to be able to force mac80211 software implementation
to be used for some tests, e.g., with virtual interface combinations
that may not yet be supported in the key cache configuration. In
addition, this allows management frame protection to be tested with
older hardware revisions.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both the agn and 3945 drivers has some problems with dealing with
errors in their probe functions. Ensure that a goto will undo only
things that was done before the goto was called.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt73usb.c . IDs 'stolen' from the
windows inf file(10/21/2008, 1.03.02.0000) plus some
from the Ralink linux driver(2009_0206_RT73_Linux_STA_Drv1.1.0.2.tar.bz2)
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt2500usb.c . IDs 'stolen' from the
windows inf file(02/12/2009, 2.01.01.0015).
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, tmspci tokenring driver crashes on device initialization
because it requests its irq before initializing corresponding data
structures. Fix this by moving request_irq call to a safer place.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error count a per-NIC variable.
Reset this the count after an hour if it has not reached the critical value.
Set the critical value back to 5.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flushing queues we disable normal interrupt and event handling and
poll event queue 0 looking for flush completions. Unfortunately the
flush event polling loop fails to move past any other type of event.
This problem has not been observed in production hardware but appears to
be a possibility.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_del_adapter() leaves dangling pointers in the structure. If we
retry the NIC probe and pass the structure to i2c_add_adapter() again
it will lead to an oops unless we clear it first.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MAC switching fails, stop the port properly.
If PHY reinitialisation fails, clear the port_initialized flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6833c043f9 introduced the phy
auto-powerdown capability. While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices. However, the 5906 phy departs from the
usual design. This commit was interfering with the 5906's ability to
negotiate link against some switches. This patch corrects the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (--worklimit >= 0); worklimit reaches -1 after the loop. In
3c589_cs.c this caused a warning not to be printed.
In 3c574_cs.c contrastingly, el3_rx() treats worklimit differently:
static int el3_rx(struct net_device *dev, int worklimit)
{
while (--worklimit >= 0) { ... }
return worklimit;
}
el3_rx() is only called by function el3_interrupt(): twice:
static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
int work_budget = max_interrupt_work;
while(...) {
if (...)
work_budget = el3_rx(dev, work_budget);
if (...)
work_budget = el3_rx(dev, work_budget);
if (--work_budget < 0) {
...
break;
}
}
}
The error path can occur 2 too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vendor/product IDs for new no name dm9601 compatible usb ethernet
adaptors.
Reported-by: Eric Lauriault <eric@linux.ca>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limitation to only 1500 byte mtu's limits the utility of the veth
device for testing routing. So implement implement a configurable
MTU.
For consistency I drop packets on the receive side when they are
larger than the MTU. I count those drops. And I allow
a little padding for vlan headers.
I also test the mtu when a new device is created with netlink
because that path currently bypasses the current mtu setting
code.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o set port mode after resetting device.
o prefer cut-through firmware (doesn't require on-card memory).
o load flashed firmware if newer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support larger dma mask if firmware indicates capability
to handle larger addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to get and set port parameters.
Currently it is used to set maximum TX/RX frame sizes. This process is
also capable of setting:
1) Pause type: Standard or Priority based.
2) Loop back mode.
3) Enable Jumbo frame mode (included here...)
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has more firmware support for link management, setting
TX and RX maximum frame sizes.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be used for setting things like maximum
frame size, setting WOL, and ACKing changes requested by the FCOE
function.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a
lot of different regions in the chip - to keep the code as clean as possible,
the ranges were put in an H file. Some areas cannot be read if the driver is
running - so by default, the driver will not access those areas - but any
programmer facing a problem will be able to easily manipulate the driver to
extract full dump. The full dump can also be used with kernel dump modules in
case of kernel panic.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the FP index to relevant debug prints and simply beautify some others
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 8726 module detection option is disabled, module should be transmitting
regardless of invalid read from EEPROM
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microcode download requires write of another register and read from
"Limiting/LRM mode" register before setting
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unload, the FW assumes that no packets will be sent after the driver sends
the FW stop command. To ensure that, the driver must always call
netif_tx_disable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using DMA engine (DMAE) to initialize large consecutive memories in the chip
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the napi_poll budget only when updating it. Also add a comment to explain
the rmb
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx interrupt is very short and there is no need to limit it to a budget
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rmb to read status block indices on load
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment explains, this smb_mb is needed only if the queue is stopped
(which is unlikely) so the barrier can be moved to that location
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Ben Hutchings <bhutchings@solarflare.com>, these are the
capabilities offsets and not the ID itself
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Ben Hutchings <bhutchings@solarflare.com>, these smb_mb are not
needed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch enables SMC911x support to work on the OMAP LDP
board. Although the SMC911x driver will eventually be obsoleted, the
smsc911x patches are rather invasive for the -rc kernels.
Rather than risk destablising smsc911x, this simpler patch is preferred
to allow the network interface to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion to avoid using pci_alloc_consistent() broke the firmware
load process, as well as added an order-4 kmalloc and doubled the memory
usage of the firmware image. Go back to loading a page at a time.
Also, since the user can now give us utter garbage for firmware, do a
cursory validation so we don't try to load just anything.
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in reference to the issue shown in kerneloops (search e1000 unmap)
The e1000 transmit code was calling pci_unmap_page on dma handles that it
might have called pci_map_single on.
Same bug as e1000e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in reference to https://bugzilla.redhat.com/show_bug.cgi?id=484494
Also addresses issue show in kerneloops
The e1000e transmit code was calling pci_unmap_page on dma handles that it
might have called pci_map_single on.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb_orphan call from igb driver as it can cause multiple issues due
to the fact that it is calling the desctructor and removing the skb from
the socket prior to transmission.
The call was added to improve performance but did so by allowing the skb to
be removed from the socket which gave the socket more window space to
transmit. The performance gain is not worth the extra problems that this
kind of workaround can introduce as this could lead to a potential DoS if a
UDP stream decided to monopolize the transmit path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinitialise LEDs after overriding them for identification.
Rename set_fault_led method to set_id_led since we always use it for
NIC identification and not faults.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new PHY supporting SFP+ modules, used in the SFN4112F
reference design. It is similar to the QT2022C2 and shares much of
its support code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuffle bits of the OUI into the conventional written order.
Replace PHY id component macros with functions.
Zero-pad PHY id components in log messages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SFN4111T initialisation, check whether the PHY boot status
indicates a bad firmware checksum. If so, prepare to reflash rather
than continuing with normal initialisation.
Remove redundant PHY boot status check from tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 27dd2caca4 changed
mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and
to combine their values into an unsigned 32-bit mask. This made the
following test for a negative (failure) value useless. Fix it to
check whether either read failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the device to give the driver RX data with reorder information.
When that is done, the device will indicate the driver if a packet has
to be held in a (sorted) queue. It will also tell the driver when held
packets have to be released to the OS.
This is done to improve the WiMAX-protocol level retransmission
support when missing frames are detected.
The code docs provide details about the implementation.
In general, this just hooks into the RX path in rx.c; if a packet with
the reorder bit in the RX header is detected, the reorder information
in the header is extracted and one of the four main reorder operations
are executed. In one case (queue) no packet will be delivered to the
networking stack, just queued, whereas in the others (reset, update_ws
and queue_update_ws), queued packet might be delivered depending on
the window start for the specific queue.
The modifications to files other than rx.c are:
- control.c: during device initialization, enable reordering support
if the rx_reorder_disabled module parameter is not enabled
- driver.c: expose a rx_reorder_disable module parameter and call
i2400m_rx_setup/release() to initialize/shutdown RX reorder
support.
- i2400m.h: introduce members in 'struct i2400m' needed for
implementing reorder support.
- linux/i2400m.h: introduce TLVs, commands and constant definitions
related to RX reorder
Last but not least, the rx reorder code includes an small circular log
where the last N reorder operations are recorded to be displayed in
case of inconsistency. Otherwise diagnosing issues would be almost
impossible.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Edited by Inaky to fix conflicts due to changes in netdev.c
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer i2400m firmwares (>= v1.4) extend the data RX protocol so that
each packet has a 16 byte header. This header is mainly used to
implement host reordeing (which is addressed in later commits).
However, this header also allows us to overwrite it (once data has
been extracted) with an Ethernet header and deliver to the networking
stack without having to reallocate the skb (as it happened in fw <=
v1.3) to make room for it.
- control.c: indicate the device [dev_initialize()] that the driver
wants to use the extended data RX protocol. Also involves adding the
definition of the needed data types in include/linux/wimax/i2400m.h.
- rx.c: handle the new payload type for the extended RX data
protocol. Prepares the skb for delivery to
netdev.c:i2400m_net_erx().
- netdev.c: Introduce i2400m_net_erx() that adds the fake ethernet
address to a prepared skb and delivers it to the networking
stack.
- cleanup: in most instances in rx.c, the variable 'single' was
renamed to 'single_last' for it better conveys its meaning.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For power saving reasons, WiMAX links can be put in idle mode while
connected after a certain time of the link not being used for tx or
rx. In this mode, the device pages the base-station regularly and when
data is ready to be transmitted, the link is revived.
This patch allows the user to control the time the device has to be
idle before it decides to go to idle mode from a sysfs
interace.
It also updates the initialization code to acknowledge the module
variable 'idle_mode_disabled' when the firmware is a newer version
(upcoming 1.4 vs 2.6.29's v1.3).
The method for setting the idle mode timeout in the older firmwares is
much more limited and can be only done at initialization time. Thus,
the sysfs file will return -ENOSYS on older ones.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming modifications will need to test for the running firmware
version before activating a feature or not. This is helpful to
implement backward compatibility with older firmware versions.
Modify i2400m_firmware_check() to encode in i2400m->fw_version the
major and minor version numbers of the firmware interface.
As well, move the call to be done as the very first operation once we
have communication with the device during probe() [in
__i2400m_dev_start()]. This is needed so any operation that is
executed afterwards can determine which fw version it is talking to.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware interface version 8.x.x has long been deprecated and is no
longer supported (nor available, as it is a preproduction firmware),
so it can be safely dropped.
Add support for firmware interface v9.2.x (current is 9.1.x). Firmware
version 9.2.x is backwards compatible with 9.1.x; new features are
enabled if switches are pressed to turn them on. Forthcoming commits
to the driver will start pressing those switches when the firmware
interface supports it.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support backwards compatibility with older firmwares when
a driver is updated by a new kernel release, the i2400m bus drivers
can declare a list of firmware files they can work with (in general
these will be each a different version). The firmware loader will try
them in sequence until one loads.
Thus, if a user doesn't have the latest and greatest firmware that a
newly installed kernel would require, the driver would fall back to
the firmware from a previous release.
To support this, the i2400m->bus_fw_name is changed to be a NULL
terminated array firmware file names (and renamed to bus_fw_names) and
we add a new entry (i2400m->fw_name) that points to the name of the
firmware being currently used. All code that needs to print the
firmware file name uses i2400m->fw_name instead of the old
i2400m->bus_fw_name.
The code in i2400m_dev_bootstrap() that loads the firmware is changed
with an iterator over the firmware file name list that tries to load
each form user space, using the first one that succeeds in
request_firmware() (and thus stopping the iteration).
The USB and SDIO bus drivers are updated to take advantage of this and
reflect which firmwares they support.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Guo-Fu Tseng <cooldavid@cooldavid.org>
Advance version number after previous changes.
Sorry for not come along with previous patch series.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate. cdc_ether is an example of
such a driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.
So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up. This patch adds the device id to cdc_ether.c as a workaround.
Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c. See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
All JMC250 chips have no problem with higher bits support.
Adding it back.
Found-by: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear all modified GHC register flags.
Fixed-by: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should sync ring descriptor to pci device after modifying it.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies messages to display correct hardware version.
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.
I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.
Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'pap' is never used in ixgbe_dcb_hw_config_82599()
and 'eec' in ixgbe_acquire_eeptom() is only used when
status == 0 but GCC has some trouble seeing that.
Signed-off-by: David S. Miller <davem@davemloft.net>
request_firmware() gives vmalloc'd memory, which is not suitable
for pci_map_single() and friends.
Use a kmalloc()'d copy of the firmware for this DMA operation.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the hardware-specific code in place, add all supported device id's,
along with base driver changes to enable 82599 devices. The devices
being enabled are:
8086:10f7: 82599EB 10 Gigabit KX4 Network Connection
8086:10fb: 82599EB 10 Gigabit Network Connection
The device 8086:10fb is a fully-pluggable SFP+ NIC.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the DCB (Data Center Bridging) support for 82599 hardware.
This is similar to how the 82598 DCB code works.
This patch also removes the BCN (Backwards Congestion Notification) netlink
configuration code from the driver. BCN was a pre-standard congestion
notification framework, and was not what the IEEE body decided upon for
standard congestion management. QCN (802.1Qau), Quantized Congestion
Notification is the accepted standard, which is not supported by 82599,
hence we remove the support altogether.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the hardware initialization code specific to 82599. This
is similar to the 82598 hardware initialization code. It also includes all
changes to the existing hardware init code to support 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell reported that bus_id from struct device will be removed, use
dev_name() instead.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An error path in ath9k_add_interface() did not unlock the sc->mutex and
could leave the driver in quite unresponsive state.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keeping this one simple.
Changing a few "foo * bar" to "foo *bar"
Removes 22 checkpatch.pl errors, with no introduced warnings.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-add the iwl_poll_direct_bit return value assignment dropped in
"iwl3945: add apm ops".
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize is_valid_rtc_data_addr function pointer for iwl3945 to
prevent a NULL pointer dereference in iwl_dump_nic_error_log.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"warning: large integer implicitly truncated to unsigned type"
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11g is in 2 ghz band, not 5 ghz.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do this by indicating the end of the appropriate regions of memory.
Note that MAX_PDA_SIZE should only apply to the PDA block read from
flash/EEPROM, and has been erronously applied to the pdr elements.
Remove the macro, and use the actual PDA size passed down by the caller.
We also fix up some of the types used, marking as much as possible
const, and using void* for the end pointers.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the Agere firmware headers for validity before attempting to
download it.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's easier to have the TODO list in wiki, so add a link to the list.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Additional attempts to fix Oops on disconnect, that appear to be successful.
However, some may be extraneous.
The cancel_delayed_work call is probably the most necessary. The
device_unplugged check may not be necessary. del_timer_sync may not
be necessary either, but the Oops I was receiving was related to
timers. Hence the addition.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup dma on stack issues:
- no DMA on stack
- cleanup unclear endianness issue
Corrected version of Oliver Neukum's original patch for at76_usb.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
flush_workqueue needs to be called instead of the generic one and the
associated functions need to be modified to prevent re-adding
themselves to the workqueue.
The rx_tasklet is also killed in the small (?) chance it is scheduled.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are roaming we allow to follow beacon hints.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts code to use the new b43_radio_maskset() API.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression dev, addr, mask, set;
@@
-b43_radio_write16(dev, addr, (b43_radio_read16(dev, addr) & mask) | set);
+b43_radio_maskset(dev, addr, mask, set);
// </smpl>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts code to use the new b43_radio_mask() API.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression dev, addr, mask;
@@
-b43_radio_write16(dev, addr, b43_radio_read16(dev, addr) & mask);
+b43_radio_mask(dev, addr, mask);
// </smpl>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts code to use the new b43_radio_set() API.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression dev, addr, set;
@@
-b43_radio_write16(dev, addr, b43_radio_read16(dev, addr) | set);
+b43_radio_set(dev, addr, set);
// </smpl>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts code to use the new b43_phy_maskset() API.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression dev, addr, mask, set;
@@
-b43_phy_write(dev, addr, (b43_phy_read(dev, addr) & mask) | set);
+b43_phy_maskset(dev, addr, mask, set);
// </smpl>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts code to use the new b43_phy_mask() API.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression dev, addr, mask;
@@
-b43_phy_write(dev, addr, b43_phy_read(dev, addr) & mask);
+b43_phy_mask(dev, addr, mask);
// </smpl>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts code to use the new b43_phy_set() API.
The semantic patch that makes this change is as follows:
// <smpl>
@@
expression dev, addr, set;
@@
-b43_phy_write(dev, addr, b43_phy_read(dev, addr) | set);
+b43_phy_set(dev, addr, set);
// </smpl>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas SDIO interface scheduled the packet worker, resulting in
unwanted latency for every data packet or command sent to the firmware.
Fix a bug on the SDIO probe error path too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the new sw scan callbacks in b43.
They are currently used to turn CFP update in the microcode off while scanning.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the PCI slow clock workaround, if we're running a PCI core rev <= 10.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not turn off the crystal, if the boardflags tell us so.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes initialization of some radio related hostflags.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a compiletime assertion for a recently introduced
assumption on the slot counts.
The tx header cache handling code assumes that the TX slot count
can be divided evenly by the number of TX slots per frame.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short calibration interval is different for AP
mode, fix this. Also, the timer should be rearmed in
the calibration routine during scanning.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_release_region() has to be called after the device
has been disabled. Also remove a stray __init attribute.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using wrong chainmasks would have an adverse impact on performance.
This patch fixes chainmask retrieval for non-PCIE cards.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OLC_FOR_AR9280_20_LATER is defined in multiple places,
move it to a common location.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reset automatically the TSF on re-enabling beaconing after scanning
in IBSS mode causes several problems. For example a new created IBSS
network can't age before an other node has joined, because scans are
done automatically in that case. And several other strange bugs more...
The TSF reset is done manually in the higher level mac80211 code in
the cases were it's needed, so we don't need to do it here.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the old days we used one slot per frame. But when we changed that to 2,
we didn't raise the overall slot count. Which resulted in an effective
division of two to the number of slots.
Double the number of TX slots, so we have an effective hardware queue
of 128 frames per QoS queue.
Also optimize the TX header cache handling. We don't need a cached TX header
for slots that will never carry an actual header.
So we reduce the memory consumption of the cache by 50%.
So as a net result we end up with more or less the same memory usage before
and after this patch (except a few tiny meta structures), but have twice
the number of TX slots available.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes hidden bugs in the size handling of the DMA buffers.
This sets the RX buffer size to the theoretical max packet size and
fixes passing of the size values to the device (must not subtract the header offset).
These bugs are hidden and don't actually trigger due to the magic +100
offset for the buffer size.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the DMA stop sanity check up a few lines, so it's actually
theoretically possible to trigger. (But it still shouldn't trigger, of course).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Passing beacons received from other BSS to s/w in non-scanning
state is unnecessary in STA mode. This patch filters them out in
h/w.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because iwlwifi
driver calls DMA mapping with PCI_DMA_TODEVICE which is read only in mapping
PTE. But iwlwifi device actually writes to the mapped page to update its contents.
This issue is not exposed in swiotlb. But VT-d hardware can capture this fault and
stop the fault transaction.
The iwl TX command contains a scratch field that is updated by uCode to
indicate retry counts. For 5000 series the patch is required also for
regular frames, but this patch does not differenciate.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies use of SW rfkill between 3945 and agn driver.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes duplicate code from iwl3945 and uses
iwl_rx_reply_error and spectrum notifications from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes duplicate rx handlers(pm_sleep and pm_debug) from 3945 and
uses handlers from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_mac_hw_scan callback instead of
iwl3945_mac_hw_scan callback.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch makes use of iwl_rx_scan handler for 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
at76_debug should be an unsigned int as it used as a bit field. In
fact, modprobe fails when trying to set at76_debug's high bit.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the latest mac80211 stack, the driver needs to be updated for
cfg80211 scanning. I based the changes off of modifications for
at76_usb found here:
http://johannes.sipsolutions.net/patches/old/all/2008-09-19-13:35/020-cfg80211-scan.patch
The trick was that max_signal also needs to be set to avoid a divide
by zero Oops. I just guessed and used the value 100 for now.
kvalo: handpicked the change from two different patches
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a driver for usb devices based on at76c50x chipset. This is
a mac80211 port of the original at76_usb driver.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Default to MAX_UCODE_BEACON_INTERVAL if the output of
iwl_adjust_beacon_interval would otherwise be zero. This prevents a
division by zero on my iwl5300-equipped Lenovo T400 with kernels that
include "mac80211: use cfg80211s BSS infrastructure".
This patch is a bit of a hack -- I'm not sure why iwl_setup_rxon_timing
is giving iwl_adjust_beacon_interval a zero input (which is the only way
it would output zero). I would be happy to have a better fix. But for
now, this makes my box boot...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch expands the parenthesis in the txctl reg write
of the LO calibration to enforce precedence rules.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanned BSS entries are timestamped with jiffies, which doesn't
increment across suspend and hibernate. On resume, every BSS in the
scan list looks like it was scanned within the last 10 seconds,
irregardless of how long the machine was actually asleep. Age scan
results on resume with the time spent during sleep so userspace has a
clue how old they really are.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs don't start BA negotiation with the client before it is done
with the key handshake in WPA/RSN. With those APs, key handshake times
out if EAPOL frames are sent after addba request. So defer the BA negotiation
until we are done with tx/rx of all EAPOL frames.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The word_base is in bytes instead of word index number,
this means that when using it, it should be transformed into
a word index first.
Otherwise RF register reading will fail through debugfs since
we would start reading 4 words starting with word 4 (which is the last
valid word for RF).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting up the CAB queue requires only the beacon interval,
remove the function ath_get_beaconconfig() which is redundant.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set channel change time to 5ms, this will improve scan results.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX and calibration have different timeout requirements.
This patch fixes it by changing the HW wait routine
to accept a timeout value.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
