bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.
v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).
v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.
v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.
v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dc ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnx2_init_board, missing free temp_stats_blk on error path when
some operations do failed. Just add the 'kfree' operation.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we have two processes to do:
P1#: ifconfig eth0 down; which will call bnx2_close, then will
, and set Null to stats_blk
P2#: ifconfig eth0; which will call bnx2_get_stats64, it will
use stats_blk.
In one case:
--P1#-- --P2#--
stats_blk(no null)
bnx2_free_mem
->bp->stats_blk = NULL
GET_64BIT_NET_STATS
then it will cause 'NULL Pointer' Problem.
it is as well with 'ethtool -S ethx'.
Allocate the statistics block at probe time so that this problem is
impossible
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.
If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)
https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking twice for ec->tx_coalesce_usecs_high, remove the
duplicate test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild-all@01.org
Fixes: 2f9130709d ("net: bcmgenet: Implement TX coalescing control knobs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c48f350ff5 "bnx2x: Add MFW dump support" added the
bnx2x_update_mfw_dump() function that reads the current time and stores
it in a 32-bit field that gets passed into a buffer in a fixed format.
This is potentially broken when the epoch overflows in 2038, and
otherwise overflows in 2106. As we're trying to avoid uses of
struct timeval for this reason, I noticed the addition of this
function, and tried to rewrite it in a way that is more explicit
about the overflow and that will keep working once we deprecate
struct timeval.
I assume that it is not possible to change the ABI any more, otherwise
we should try to use a 64-bit field for the seconds right away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:
drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'
Add the missing argument.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf4 ("tg3: Add hwmon support for temperature")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: stable@vger.kernel.org [v3.6+]
Signed-off-by: David S. Miller <davem@davemloft.net>
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for 3 new PCI device combinations -
1077:16a1, 1077:16a4 and 1077:16ad.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom buses may have more than 1 Ethernet device. This is used e.g.
to have few interfaces connected to different switch ports. So far we
saw chipsets with only 2 devices (e.g. BCM4706) but recent ones have
up to 3 (e.g. Netgear R8000 uses 3rd interface for most of switch
traffic, lower interfaces are for some kind of offloading).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the dma flags of multiq ring buffer int the interface stop
process. This patch fixes that the genet is not running while the
interface is re-enabled.
$ ifup eth0 - running after booting
$ ifdown eth0
$ ifup eth0 - not running and occur tx_timeout
The bcmgenet_dma_disable() in bcmgenet_open() do clean ring16 dma flag
only. If the genet has multiq, the dma register is not cleaned. and
bcmgenet_init_dma() is not done correctly. in case
GENET_V2(tx_queues=4), tdma_ctrl has 0x1e after running
bcmgenet_dma_disable().
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_timeout() executes in atomic context, yet we will invoke
napi_disable() which does sleep. Looking back at the changes, disabling
TX napi and re-enabling it is completely useless, since we reclaim all
TX buffers and re-enable interrupts, and wake up the TX queues.
Fixes: 13ea657806 ("net: bcmgenet: improve TX timeout")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34fa14cc0 ("bnx2x: Add vxlan RSS support") has introduced an
endianity issue when passing the vxlan UDP port to the HW.
Reported-by: <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW submission added some vxlan offload capabilities to our device.
This patch adds the ability to connect to the vxlan NDOs and configure
the UDP port associated with it in the HW.
The device would now be capable of performing RSS according to the
inner headers of the vxlan packets.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.
For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.
Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.
This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 230d00eb4b ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has introduced
an incorrect logic for checking whether pvid should be configured for
a vf, causing the hypervisor driver to send unneeded ramrods for all of
the vfs each time a pvid has changed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd ("bnx2x: add vlan filtering offload") has broken
compilation when CONFIG_BNX2X_SRIOV is not set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver always uses vlan-promisc mode, i.e., it receives both
tagged and untagged traffic and lets the network stack drop packets
tagged with unrequested vlan tags.
This patch implements vlan-filtering offload in the driver -
Unless explicitly configured to promisc mode, only untagged packets or
packets tagged with requested vlans would reach the Rx flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change
detection") added a fixed PHY link_update callback for MoCA PHYs when
registered using platform_data exclusively, this change is also
applicable to systems using Device Tree as their primary configuration
interface.
In order for this to work, move the link_update assignment into
bcmgenet_moca_phy_setup() where we know for sure that we are running on
a MoCA GENET instance, and do not override phydev->link since this is:
- properly taken care of by the PHY library by getting the link UP/DOWN
interrupts
- this now runs everytime we call bcmgenet_open(), so we need to
preserve whatever we detected before we went administratively DOWN and
then UP
- we need to make sure that MoCA PHYs start with a link DOWN during
probe in order to force a link transition to occur
To avoid a forward declaration, move bcmgenet_fixed_phy_link_update()
above its caller.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of multiplying the number of checks for IS_ERR(priv->clk),
simply NULLify the 'struct clk' pointer which is something the Linux
common clock framework perfectly deals with and does early return for
each and every single clk_* API functions.
Having every single function check for !IS_ERR(priv->clk) is both
redundant and error prone, as it turns out, we were doing it for the
main GENET clock: priv->clk, but not for the Wake-on-LAN or EEE clock,
so let's just be consistent here.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.
This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new copper phy.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.
This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
