A second set of feature flag bits was added, and the hardware RSC engine
flags were moved there. However, the code itself didn't make the move
completely to use the new bitmap.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our ndo_poll_controller callback is broken for anything but non-multiqueue
setups. This fixes that issue.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading hw_csum_rx_error counts. This patch adds a
test around this counter increase for this condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to device_init_wakeup should not be necessary in drivers that use
device_set_wakeup_enable since pci_pm_init will set the can_wakeup flag
for the device when initialized.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain types of control packets (LLDP, LACP, etc.) are not supposed to have a
priority tag or vlan tag inserted. Ixgbe driver is currently priority
tagging everything (if packet is not on a VLAN interface).
This patch modifies DCB mode, so that packets marked with skb priority
TC_PRIO_CONTROL are not priority tagged. It also transmits these packets on
the highest priority traffic class.
Programs (like dcbd) can set the skb priority using a socket option. Or, a tc
filter can be configured to set the priority value. Using the value
TC_PRIO_CONTROL (7) has the benefit that it is already defined in the kernel,
and the bonding LACP code already sets the skb->priority field to this value.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, FCoE offload feature is turned on when the kernel config has
CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn
FCoE offload on when there is FCoE traffic passing and turn it off when
it's just LAN traffic. Since FCoE depends on a lossless network provided
by DCB, this allows us to have FCoE turned on/off when user turns on DCB
using dcbtool.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the version number marching along as updates come in.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for a new copper device for 82598, device id 0x150b.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link comes up, the driver detects which flow control settings are
active. This is done using bitwise operations directly from the hardware
registers, and assumes the proper boolean assignment. Make this an
explicit boolean value before assignment to the bool.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().
I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module. So we
only check if that is the case.
This problem also shows up on Copper devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.
- mdio45_probe call was always failing due to mdio.prtad not being
set. The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0. This will allow us to set the phy_id
and phy.type correctly now.
- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.
- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses three WARN_ON statements from DMA-API debug code
ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.
found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.
in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single
and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a wide range of log messages for the same sort of SFP
failure. This patch makes them all more similar and less
confusing along with converting them to dev_err.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Include offloaded FCoE data into total rx/tx statistics for 82599 so they
are properly reflected by ethtool or ifconfig.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 has a FW running that helps manage the internal SFI PHY. There are
also a number of pre-production samples of these SFI-based devices in the
field. This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified. The driver will continue loading
though, with no functional degradation.
Also remove an old function prototype from ixgbe_82599.c that isn't being
used.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables Flow Director's ATR functionality to the main base
driver for 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a second feature flag variable to use for future feature
expansion. Add HW RSC to this new feature flags variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine. This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v_idx value was being used as both a bitmask and an index. This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags. This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ethtool internal test engine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 KX4 device defaults to legacy power management, or APME. This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build warning due to an unused label.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in. This patch corrects that by:
ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.
ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.
ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected. Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.
Other functions were updated to allow correct logging.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver tries to re-register the DCA requester after reset and
this is not correct. This change makes it so all we are doing is resetting
the DCA registers after reset and not re-adding the requester.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is purely a cleanup patch. This collapses some of the code required
when we configure our Tx and Rx feature sets, and makes the code more
readable and maintainable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marching along, let's bump the version number to indicate things actually
have happened to the driver.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the generic XAUI device support for 82599 controllers.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The performance of hardware RSC is greatly reduced if the total for max rsc
descriptors multiplied by the buffer size is greater than 65535. To
prevent this we need to adjust the max rsc descriptors appropriately.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports using either link flow control or priority flow control when
in DCB mode. The dcbnl interface already supports sending down
configurations through rtnetlink that can enable LFC when DCB is enabled,
so the driver should take advantage of this.
82598 does not support using LFC when DCB is enabled, so explicitly disable
it when we're in DCB mode. This means we always run in PFC mode when DCB
is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable jumbo frame when FCoE feature is enabled in 82599. Use 3K
as the receive queue buffer size for receive queues used by FCoE
to address for max Fiber Channel frame size as 2148 bytes (with
max 2112 bytes of payload).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ring feature for FCoE to make use of the FCoE redirection
table in 82599. The FCoE redirection table is a receive side
scaling feature for Fiber Channel over Ethernet feature in 82599,
enabling distributing FCoE packets to different receive queues
based on the exchange id.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the Storage Address entrypoint from the net device.
It will read the SAN MAC addresses from the EEPROM of the 82599 hardware,
and make them available to the FCoE stack through the net device.
Also, add/del the SAN MAC address to the netdev dev_addr_list via the
kernel api dev_addr_add()/dev_addr_del() when there is a valid SAN MAC
supported by the HW.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds FCoE related statistics to 82599, including number Rx-ed and Tx-ed
FCoE packets, number of Rx-ed and Tx-ed FCoE packets in dwords, number of bad
Fiber Channel CRCs detected in FCoE packets, and number of FCoE packets dropped
on the Rx side.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the FCoE Rx side offload feature in ixgbe_main.c
to 82599 using the Rx offload infrastructure code added in the previous
patch. The large receive offload by Direct Data Placement (DDP) for
FCoE is achieved by implementing the ndo_fcoe_ddp_setup and ndo_fcoe_ddp_done
in net_device_ops via netdev. It is up to the ULD, i.e., fcoe and libfc
to query and setup large receive offload accordingly through the corresponding
netdev upon creating fcoe instances.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the FCoE Tx side offload features in ixgbe_main.c
to 82599 using the Tx offload infrastructure code added in the previous
patch. This is achieved by the calling the FCoE Sequence Offload (FSO)
function ixgbe_fso() on the transmit path of ixgbe.
This patch also includes an EEPROM check to make sure the NIC we're loading
on is an offload-enabled SKU.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we don't get any sign-extend issues when we shift a 1
into bit 31.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We weren't logging the 82598AT fan failure if it occurred before (ixgbe_open)
as we hadn't sent up to catch the interrupt that event caused.
This patch checks for this failure in:
ixgbe_probe - So we can log the failure asap. We check right after we
set up the adapter->flags, which is when we know that we have a fan.
ixgbe_up_complete - To catch failures that may have happened between probe
and when we set up the interrupt that would normally detect the fan failure.
To enable all of this we need to initialize the adapter flag with
IXGBE_FLAG_FAN_FAIL_CAPABLE when the NIC contained a fan.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables L2 header split when packet split is enabled for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current configuration is not setting queue 0 correctly for DCB
configurations. As a result unconfigured queues are being used to setup
the SRRCTL register rx buffer len sizes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the documentation for 82599 in order to support hardware RSC the
header size must be set. This is only currently done for packet split
mode. This patch sets the header buffer length for all modes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traditionally Intel based NIC drivers request I/O port even though it
doesn't need that really.
Intel PCIE 10Gb driver (ixgbe) also requests I/O port but it doesn't
need it either.
This is a little inconvenient situation because sometimes we have to
handle those cards on the slots where any I/O space is not attached.
So we made pach which makes ixgbe driver legacy I/O port free.
Signed-off-by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the "PCI Error Recovery" document, if after a recovery,
the bus is disabled, the error_detected function should return
PCI_ERS_RESULT_DISCONNECT. Actually ixgbe error_detected function is
always returning PCI_ERS_RESULT_NEED_RESET, even if the bus is in failure.
This patch just check if the bus is disabled and then returns
PCI_ERS_RESULT_DISCONNET.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently ixgbe_receive_skb is passing the vector index to
skb_record_rx_queue instead of the queue index. This patch changes that so
that the ring index is passed instead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the q_vectors are being allocated statically inside of the
adapter struct. This increases the overall size of the adapter struct when
we can easily allocate the vectors dynamically. This patch changes that
behavior so that the q_vectors are allocated dynamically and the napi
structures are automatically allocated inside of the q_vectors as needed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were calling pci_enable_wake() twice in a row for both D3_hot
and D3_cold. This replaces those calls with a call to pci_wake_from_d3()
to avoid issues with PCI PM vs ordering constraints.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayyappan at VMware noticed that we're missing this check from ixgbe which
is in our other drivers. The difference with this implementation from our
other drivers is that this checks all the tx queues rather than just tx[0].
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the interrupt management to correctly handle greater
than 16 queue vectors.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables hardware receive side coalescing for 82599 hardware.
82599 can merge multiple frames from the same TCP/IP flow into a single
structure that can span one ore more descriptors. The accumulated data is
arranged similar to how jumbo frames are arranged with the exception that
other packets can be interlaced inbetween. To overcome this issue a next
pointer is included in the written back descriptor which indicates the next
descriptor in the writeback sequence.
This feature sets the NETIF_F_LRO flag and clearing it via the ethtool set
flags operation will also disable hardware RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by: Vlad Yasevich <vladislav.yasevich@hp.com>
This is the code to enable ixgbe for hardware offload support
of CRC32c on both transmit and receive of SCTP traffic.
only 82599 supports this offload, not 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of these drivers do a check to verify ip_summed is set to
CHECKSUM_UNNECESSARY prior to passing the packet to GRO. GRO itself
already does such a check so it is redundant and can be removed as this
will likely cause out of order issues when receiving a packet that didn't
pass checksum validation.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code writes the PME enabled bit in PCI config space which is
wrong. This was needed for pre-release hardware, and was not removed from
the driver. Also, we need to clear the WUS (wake up status) after we
resume. Otherwise we can't wake for the same event again since it's still
asserted in the hardware. Plus, the multicast lists were being written
improperly, causing multicast WoL to fail.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Andrew Lutomirski <amluto@gmail.com>
All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice
This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.
This apparently confused *some* versions of networkmanager.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: Andrew Lutomirski <amluto@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The traffic classes in hardware are not symmetrical for Rx and Tx. Rx
is every 16 descriptor queues, Tx is not. It runs 32-32-16-16-8-8-8 when
running with 8 traffic classes, and runs 64-32-16 when running with 4
traffic classes. This patch fixes the mapping.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent ixgbe from putting the adapter into D3 during shutdown except when
we're going to power off the system, since doing that may generally cause
problems with kexec to happen (such problems were observed for igb and
forcedeth). For this purpose seperate ixgbe_shutdown() from ixgbe_suspend()
and use the appropriate PCI PM callbacks in both of them.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the update of real_num_tx_queues from
ixgbe_acquire_msix_vectors() to ixgbe_set_num_queues(), to ensure it
be always in sync with num_tx_queues.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do the num_tx_queues based masking on calculating tx queue
index.
1) num_tx_queues is not always power-of-2, because it also depends on
the online cpu numbers. So the masking could be a performance bug
on a 6 cpu system.
2) queue_mapping will be limited by real_num_tx_queues=num_tx_queues
in the generic netdev function set_cur_queue_map(). So the bound
limiting here is not necessary.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC warns:
drivers/net/ixgbe/ixgbe_main.c: In function 'ixgbe_sfp_config_module_task':
drivers/net/ixgbe/ixgbe_main.c:3920: warning: suggest parantheses around
operand of '!' or change '&' to '&&' or '!' to '~'
Which I think is right. Bracket to remove ambiguity.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all physical connection types are being correctly identified. This
fixes that issue, and cleans up the logic to make it more maintainable.
Also clean up the code for device capabilities from the EEPROM to support
multiple SKUs of the same hardware.
Bump the version to reflect all the updates since the 82599 merge.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY operations are determined, the PHY must be identified. This
identification causes bus access, and should be contained within its own
routines. This also helps the 82599 PHY init paths for both SFP+ and
KX/KX4 devices to be easier to maintain.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were basicly ignoring ethtool users request for FC autoneg
and replying to queries with a "best guess". This patch
enables the driver to store if we want to enable/disable
autoneg FC and do the correct behavior.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is made active we were not handling the error
scenarios properly to clean up rx & tx resources which might result in
a driver panic.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves an issue with map single being used to map a buffer and
then unmap page being used to unmap it. In addition it handles any error
conditions that may be detected using skb_dma_map.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI-X allocation broke after the 82599 merge on systems with more than 8
CPU cores. 82598 drops back into MSI mode, which isn't sufficient to run
full, efficient 10G line rate.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past flow control wasn't enabled by default under the
incorrect assumption that this opened up us to a denial of
service attack. However since any switch that forwarded flow
control would be extremely msiconfigured and/or buggy, this
concern no longer out weighs the preformance gains from
having FC enabled.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe driver had issues when DEBUG was defined because the hw_dbg macro
was incomplete. This patch completes the code based off of the code that
already existed in the igb module.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ixgbe to use net_device_ops properly.
Rather than changing the select_queue function pointer
just check the flag.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog will schedule an interrupt to help make sure queues are
cleaned in the case when an interrupt is missed, most likely due to very
high load. On 82599, there are extra interrupt registers to account for
the larger number of MSI-X vectors (64 total for 82599 vs. 18 total for
82598). These must be taken into account when performing this operation in
the watchdog.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup a bit of whitespace, add some function header comments, and fix a
few comments around the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx DMA unit should be disabled when bringing the device down. Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel. In those cases, we'd rather
fail gracefully instead of a panic. Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the following pieces of the Rx initialization path:
- Enable the ECC memory fault interrupt in OTHER causes.
- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled. We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.
- Fix the RSS initialization path to not stomp on DCB accidentally. When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status. The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.
Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt models using EITR have changed in 82599. The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't. This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 mistakenly enabled drop on Rx queues in the packet buffer. The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly. In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the hardware-specific code in place, add all supported device id's,
along with base driver changes to enable 82599 devices. The devices
being enabled are:
8086:10f7: 82599EB 10 Gigabit KX4 Network Connection
8086:10fb: 82599EB 10 Gigabit Network Connection
The device 8086:10fb is a fully-pluggable SFP+ NIC.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it was pointed out on the list that ixgbe was failing when using 64kB pages
and large 16kB MTU.
since with a 64kB PAGE_SIZE MAX_SKB_FRAGS = 3, the way the driver was
configuring page usage was assuming 2kB is half a page, and was only
ever dmaing that much data to a half page.
(16kB - header size) / 2048 = 7 or 8 pages, which would far exceed 3
adjust the driver to account for these large pages, the hardware can
support DMA to up to 16kB for each descriptor.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure happens when an interrupt occurs and the driver is reading
EICR. This read will cause a clear-by-read which leads to two TLP
being inserted in the PCIe retry buffer leading to an overflow of the
buffer and corruption of TLPs.
The solution is different depending where the reading of EICR takes place.
For ixgbe_msix_lsc() since we are in MSIX mode and know OCD is enabled a
clear-by-write is done instead of the normal clear-by-read.
For ixgbe_intr() 0xffffffff is written to EIMC before the read, masking the
interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the unused PAGE_USE_COUNT() macro. Also removing the unused
pages variable at ixgbe_configure_rx() function.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that our set_num_queues() routines for each feature are re-entrant, and
can be called at any point, they shouldn't zero out the feature's indices
or mask bits. Subsequent calls into those routines for those features can
result in zero Rx and Tx queues being assigned, causing a panic later in
driver reinitialization.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx Head writeback is causing multi-microsecond stalls on PCIe chipsets, due
to partial cacheline writebacks. Removing this feature removes these
issues.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow control handling is overly complicated and difficult to maintain.
This patch cleans up the flow control handling and makes it much more
explicit. It also adds 1G flow control autonegotiation, for 1G copper
links, 1G KX links, and 1G fiber links.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ixgbe does not display the EEPROM version in ethtool -i, where
other drivers do. The EEPROM version is located at offset 0x29. This
patch adds support to display it.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has some flaws in it when performing autonegotiation,
especially on KX/KX4 links. This patch updates the code to better handle
the autonegotiation states on link setup. The patch also removes a redundant
link configuration call on driver load, and moves link configuration to
the ->open() path.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code to determine the number of queues the device will want
on driver initialization is ugly and difficult to maintain. It also
doesn't allow for easy expansion for future features or future hardware.
This patch refactors these routines, and make them easier to deal with.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New year, new copyright date ranges. Also bump the driver version
number to reflect many of the recent changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our current MSI-X allocation mechanism does not support new hardware
at all. It also isn't getting the actual number of supported MSI-X vectors
from the device.
This patch allows the number of MSI-X vectors to be specific to a device,
plus it gets the number of MSI-X vectors available from PCIe configuration
space.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID for BX devices using the 82598 MAC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And support for the KX/KX4 mezzanine card. Device id 0x10B6.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load times for NICs that use i2c to communicate with the phy were taking
~4.5 sec per port. This fix first checks to see if the link is already
up before calling get_link_capabilities, since if it is we don't need
query the phy for link state.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ixgbe invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
As GRO uses the napi structure to track the held packets, I've
modified the code paths involved to pass that along.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register VLAN ID 0 so that frames with VLAN ID 0 are received and get
their tag stripped when ixgbe is not in DCB mode. VLAN ID 0 means
that the frame is 'priority tagged' only - it is not a VLAN, but the
priority value is the tag in valid. The functions
ixgbe_vlan_rx_register() and ixgbe_vlan_rx_kill_vid() were moved up a
couple functions to correct compiling issues with this change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Eric W Multanen <eric.w.multanen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The is an issue where setting Relaxed Ordering (RO) bit
(in a PCI-E write transaction) on 82598 causing the chipset
to drop DCA hints. This patch forces RO not to be set for
descriptors as well as payload. This will only be in effect
while DCA is enabled and no performance difference was
noticed in testing.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows DCB mode to change the number of queues, and presumably
the number of NAPI instances, safely.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was initially reported by Joerg Roedel <joerg.roedel@amd.com>
It appears that ixgbe has had a long standing bug where it was unmapping a different size than it had mapped.
ixgbe 0000:02:00.0: PCI-DMA: device driver frees DMA memory with different sizes than it mapped.
ixgbe 0000:02:00.0: PCI-DMA: device driver frees DMA memory with different size [device address=0x0000000003fed812] [map size=258 bytes] [unmap size=256 bytes]
Pid: 6178, comm: rmmod Not tainted 2.6.28-rc5 #4 Call Trace:
[<ffffffff8022a2ae>] iommu_queue_inv_iommu_pages+0x5e/0x70
[<ffffffff80225956>] check_unmap+0x1c6/0x240 [<ffffffff80225ff5>] debug_unmap_single+0xb5/0x110 [<ffffffffa0213997>] ixgbe_clean_rx_ring+0x147/0x220 [<ffffffffa0214d7d>] ixgbe_down+0x2fd/0x3d0 [ixgbe] [<ffffffffa02150b3>] ixgbe_close+0x13/0xc0 [ixgbe] [<ffffffff80431326>] dev_close+0x56/0xa0 [<ffffffff804313b3>] rollback_registered+0x43/0x220 [<ffffffff804315a5>] unregister_netdevice+0x15/0x60 [<ffffffff80431601>] unregister_netdev+0x11/0x20 [<ffffffffa021aef8>] ixgbe_remove+0x48/0x16e [ixgbe] [<ffffffff80386ffc>] pci_device_remove+0x2c/0x60 [<ffffffff803ef929>] __device_release_driver+0x99/0x100
[<ffffffff803efa48>] driver_detach+0xb8/0xc0 [<ffffffff803eea6e>] bus_remove_driver+0x8e/0xd0 [<ffffffff80387374>] pci_unregister_driver+0x34/0x90 [<ffffffff8026c6c7>] sys_delete_module+0x1c7/0x2a0 [<ffffffff802a9ce9>] do_munmap+0x349/0x390 [<ffffffff80374481>] __up_write+0x21/0x150 [<ffffffff8020c30b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the PCIe Advanced Error Reporting callbacks in
ixgbe. The 82598 hardware supports AER, so we enable it.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems the ixgbe's code was copied from e1000.
The comment talks about something not exist.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option. In addition, added useful help text for the
Kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1). These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.
Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.
Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Data Center Bridging (DCB) features in the ixgbe
driver and adds an rtnetlink interface for configuring DCB to the
kernel. The DCB feature support included are Priority Grouping (PG) -
which allows bandwidth guarantees to be allocated to groups to traffic
based on the 802.1q priority, and Priority Based Flow Control (PFC) -
which introduces a new MAC control PAUSE frame which works at
granularity of the 802.1p priority instead of the link (IEEE 802.3x).
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off() is sufficient to stop Tx into the driver. Stopping the Tx
queues is redundant and unnecessary. By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot select INTEL_IOATDMA in Kconfig as soon as MYRI10GE or IXGBE
is enabled since the former is not available on all architectures.
Just use a Kconfig bool {IXGBE,MYRI10GE}_DCA set to =y when DCA
support can actually be built.
[myri10ge portion written and signed-off-by] Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch cleans up some whitespace items, reorders a couple of functions, and removes some outdated comments.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch corrects support for NAPI so that queues are correctly added and
removed during suspend/resume in the event that the number of MSI-X vectors
changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe_xmit_frame can be refactored to use fewer locals and better
utilize common kernel macros.
also fixed minor buglet with internal to driver vlan flag variable being
passed incorrectly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
some functions were un-necessarily using local variables.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is partial preparation for a future patch which will extend
ixgbe_set_num_queues
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
clean up the hardware shutdown sequence to prevent hardware
from continuing to send when resetting or unloading.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.
This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
in some configurations there can be more than one rx queue per vector
in msi-x mode. Add functionality to be able to clean this without
changing the performance path single-rx-queue cleanup.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
changing ring sizes in ethtool needs to be robust. If an allocation fails the
driver must continue operation, with the previous settings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
most of the time we only need 1500 bytes for a packet which means
we don't need a whole 4k page for each packet. Share the allocation
by using a reference count to the page and giving half to two
receive descriptors. This can enable us to use packet split mode
all the time due to the performance increase of allocating half
the pages.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe was incorrectly setting the throttle rate setting for all tx
queues and the driver has been refreshed to better handle a dynamic
interrupt mode as well as multiple queues.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Upon review a buglet was found where link change was not causing
an immediate link change event as it should.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change makes it so only one srrctl register is programmed per VMDq id, and if VMDq is not enabled it is one register per RSS queue. Currently this function is working correctly for the multiqueue RSS and single queue cases, but if any advances features such as VMDq or DCB would have been enabled this function would have caused issues as it was not correct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change TSO offloads to use a different context than VLAN insertion
and Tx checksumming. Hardware has separate registers internally for
storing these so use them.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hardware was configured incorrectly which led all hints to be
sent to queue[0]'s DCA configuration.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DCA related fixes
=================
- ixgbe was not compiling and using DCA correctly if dca was a module
- DCA interface changed with new kernel
- ixgbe was not correctly configured to indicate DCA hints to the
correct CPU.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
as mentioned by Herbert, our hardware supports IP offloads, not full
checksum offloads for any protocol in existence (even though the
hardware just provides generic csum support over any range of bytes)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This locks the seed down so loading/unloading the driver will present
predictable hashing from RSS. Also move the rx_buf_len out of the adapter
struct, and into the Rx ring struct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable Tx Head Writeback in the hardware. This helps performance by
removing adapter writebacks to descriptors on transmit completion.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the adapter cannot tell what the remote end's flow control capability
is through auto-neg, we must turn off flow control by default.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cleanup all the different references to the Tx ring and Rx ring structures
and make them common across the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement HAVE_SET_RX_MODE in the driver for MC and UC lists.
Signed-off-by: Christopher Leech <christopher.leech@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
the driver was misinterpreting rx_csum return value in the descriptor
so occassionally we would indicate an rx_csum error in our stats
when there was none. This would have no effect on traffic because
we would just hand the packet to the stack anyway without the offload
flag set, but would increase CPU for those packets that needed a recompute.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit dropped the setting of the default interrupt throttle rate.
commit 021230d40a
Author: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Date: Mon Mar 3 15:03:45 2008 -0800
ixgbe: Introduce MSI-X queue vector code
The following patch adds it back. Without this the default value of 0
causes the performance of this card to be awful. Restoring these to the
default values yields much better performance.
This regression has been around since 2.6.25.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: stable@kernel.org [2.6.25 and later]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VLAN filtering is broken, due to reading the incorrect register for
the VLAN filtering settings. Fixed by reading/writing the correct
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a simple device ID add for adapters that support
CX4 (copper infiniband style cable) connectors for 10GbE.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling
netif_tx_start_all_queues() before calling netif_tx_wake_all_queues().
This causes an issue during loading of the driver.
In addition, updated e1000e to use the updated tx mutliqueue api.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for a feature bit for something that
can be tested by simply checking the TX queue count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed in this thread:
http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEh is not recovering in a resonable amount of time on PPC during
ixgbe_down().
Signed-off-by: Paul Larson <pl@us.ibm.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for in-kernel LRO with the ability to enable/disable via ethtool
based on comments from Ben Hutchings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using the new interface for propagating device feature flags into VLAN
devices, turn on TSO and CSUM offload on VLAN devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To enable EEH support for pci-express network adapters, pcie/msi state
needs to be saved and restored for that adapter.
Tested this EEH patch with Intel 10G pci-express ixgbe adapter.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Under CONFIG_DCA the compilation is broken since the commit
bd0362dde0 (ixgbe: Add optional
DCA infrastructure).
IXGBE_SUCCESS is not defined anywhere, replace it with 0.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
82598 cards and up support DCA, which enables the chipset to warm
up the caches for upcoming payload data. This code makes the
driver plug into the CONFIG_DCA infrastructure that was merged
earlier.
Signed-off-by: Jeb Cramer <cramerj@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
82598 can produce a formidable interrupt rate, and is largely
unusable without some form of moderation. The default behaviour
before this patch is to limit irq's to a reasonable number.
However, just like our other drivers we can reduce latency
for small packet-type traffic considerably by allowing the
irq rate to go up dynamically.
This patch introduces a simple irq moderation algorithm based
on traffic analysis. The driver will use more CPU to service
small packets quicker but will perform the same on bulk traffic
as the old code.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that the irq vector code is in place, we can add the conditional
multiqueue TX code in the driver. This requires the optional
CONFIG_NETDEVICES_MULTIQUEUE=y and will not be enabled without
it.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This code abstracts the per-queue MSI-X interrupt vector into
a queue vector layer. This abstraction is needed since there can
be many more queues than available MSI-X vectors in a machine.
The MSI-X irq vectors are remapped to a shared queue vector which
can point to several (both RX and TX) hardware queues. The NAPI
algorithm then cleans the appropriate ring/queues on interrupt
or poll.
The remapping is a delicate and complex calculation to make sure
that we're not unbalancing the irq load, and spreads the irqs
as much as possible, and may combine RX and TX flows onto the
same queue vector.
This effectively enables receive flow hashing across vectors
and helps irq load balance across CPUs.
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Waskiewicz Jr, Peter P <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
