Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the UCC_GETH_UPSMR_xxx definitions to qe.h. The ucc_geth driver will
eventually use these instead of the UPSMR_ macros it currently defines.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The general pci resume code can only restore part of the
configuration registers. We need to reconfigure those
registers in the FIXUP_RESUME.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add kprobe_insn_mutex for protecting kprobe_insn_pages hlist, and remove
kprobe_mutex from architecture dependent code.
This allows us to call arch_remove_kprobe() (and free_insn_slot) while
holding kprobe_mutex.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show node to memory section relationship with symlinks in sysfs
Add /sys/devices/system/node/nodeX/memoryY symlinks for all
the memory sections located on nodeX. For example:
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
indicates that memory section 135 resides on node1.
Also revises documentation to cover this change as well as updating
Documentation/ABI/testing/sysfs-devices-memory to include descriptions
of memory hotremove files 'phys_device', 'phys_index', and 'state'
that were previously not described there.
In addition to it always being a good policy to provide users with
the maximum possible amount of physical location information for
resources that can be hot-added and/or hot-removed, the following
are some (but likely not all) of the user benefits provided by
this change.
Immediate:
- Provides information needed to determine the specific node
on which a defective DIMM is located. This will reduce system
downtime when the node or defective DIMM is swapped out.
- Prevents unintended onlining of a memory section that was
previously offlined due to a defective DIMM. This could happen
during node hot-add when the user or node hot-add assist script
onlines _all_ offlined sections due to user or script inability
to identify the specific memory sections located on the hot-added
node. The consequences of reintroducing the defective memory
could be ugly.
- Provides information needed to vary the amount and distribution
of memory on specific nodes for testing or debugging purposes.
Future:
- Will provide information needed to identify the memory
sections that need to be offlined prior to physical removal
of a specific node.
Symlink creation during boot was tested on 2-node x86_64, 2-node
ppc64, and 2-node ia64 systems. Symlink creation during physical
memory hot-add tested on a 2-node x86_64 system.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The KernelPageSize entry in /proc/pid/smaps is the pagesize used by the
kernel to back a VMA. This matches the size used by the MMU in the
majority of cases. However, one counter-example occurs on PPC64 kernels
whereby a kernel using 64K as a base pagesize may still use 4K pages for
the MMU on older processor. To distinguish, this patch reports
MMUPageSize as the pagesize used by the MMU in /proc/pid/smaps.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: "KOSAKI Motohiro" <kosaki.motohiro@jp.fujitsu.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misspelling of "firmware" in powerpc Makefile
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
... and don't bother in callers. Don't bother with zeroing i_blocks,
while we are at it - it's already been zeroed.
i_mode is not worth the effort; it has no common default value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (140 commits)
KVM: MMU: handle large host sptes on invlpg/resync
KVM: Add locking to virtual i8259 interrupt controller
KVM: MMU: Don't treat a global pte as such if cr4.pge is cleared
MAINTAINERS: Maintainership changes for kvm/ia64
KVM: ia64: Fix kvm_arch_vcpu_ioctl_[gs]et_regs()
KVM: x86: Rework user space NMI injection as KVM_CAP_USER_NMI
KVM: VMX: Fix pending NMI-vs.-IRQ race for user space irqchip
KVM: fix handling of ACK from shared guest IRQ
KVM: MMU: check for present pdptr shadow page in walk_shadow
KVM: Consolidate userspace memory capability reporting into common code
KVM: Advertise the bug in memory region destruction as fixed
KVM: use cpumask_var_t for cpus_hardware_enabled
KVM: use modern cpumask primitives, no cpumask_t on stack
KVM: Extract core of kvm_flush_remote_tlbs/kvm_reload_remote_mmus
KVM: set owner of cpu and vm file operations
anon_inodes: use fops->owner for module refcount
x86: KVM guest: kvm_get_tsc_khz: return khz, not lpj
KVM: MMU: prepopulate the shadow on invlpg
KVM: MMU: skip global pgtables on sync due to cr3 switch
KVM: MMU: collapse remote TLB flushes on root sync
...
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
struct dentry is one of the most critical structures in the kernel. So it's
sad to see it going neglected.
With CONFIG_PROFILING turned on (which is probably the common case at least
for distros and kernel developers), sizeof(struct dcache) == 208 here
(64-bit). This gives 19 objects per slab.
I packed d_mounted into a hole, and took another 4 bytes off the inline
name length to take the padding out from the end of the structure. This
shinks it to 200 bytes. I could have gone the other way and increased the
length to 40, but I'm aiming for a magic number, read on...
I then got rid of the d_cookie pointer. This shrinks it to 192 bytes. Rant:
why was this ever a good idea? The cookie system should increase its hash
size or use a tree or something if lookups are a problem. Also the "fast
dcookie lookups" in oprofile should be moved into the dcookie code -- how
can oprofile possibly care about the dcookie_mutex? It gets dropped after
get_dcookie() returns so it can't be providing any sort of protection.
At 192 bytes, 21 objects fit into a 4K page, saving about 3MB on my system
with ~140 000 entries allocated. 192 is also a multiple of 64, so we get
nice cacheline alignment on 64 and 32 byte line systems -- any given dentry
will now require 3 cachelines to touch all fields wheras previously it
would require 4.
I know the inline name size was chosen quite carefully, however with the
reduction in cacheline footprint, it should actually be just about as fast
to do a name lookup for a 36 character name as it was before the patch (and
faster for other sizes). The memory footprint savings for names which are
<= 32 or > 36 bytes long should more than make up for the memory cost for
33-36 byte names.
Performance is a feature...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only significant changes were to kvmppc_exit_timing_write() and
kvmppc_exit_timing_show(), both of which were dramatically simplified.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Existing KVM statistics are either just counters (kvm_stat) reported for
KVM generally or trace based aproaches like kvm_trace.
For KVM on powerpc we had the need to track the timings of the different exit
types. While this could be achieved parsing data created with a kvm_trace
extension this adds too much overhead (at least on embedded PowerPC) slowing
down the workloads we wanted to measure.
Therefore this patch adds a in-kernel exit timing statistic to the powerpc kvm
code. These statistic is available per vm&vcpu under the kvm debugfs directory.
As this statistic is low, but still some overhead it can be enabled via a
.config entry and should be off by default.
Since this patch touched all powerpc kvm_stat code anyway this code is now
merged and simplified together with the exit timing statistic code (still
working with exit timing disabled in .config).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Store shadow TLB entries in memory, but only use it on host context switch
(instead of every guest entry). This improves performance for most workloads on
440 by reducing the guest TLB miss rate.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Formerly, we used to maintain a per-vcpu shadow TLB and on every entry to the
guest would load this array into the hardware TLB. This consumed 1280 bytes of
memory (64 entries of 16 bytes plus a struct page pointer each), and also
required some assembly to loop over the array on every entry.
Instead of saving a copy in memory, we can just store shadow mappings directly
into the hardware TLB, accepting that the host kernel will clobber these as
part of the normal 440 TLB round robin. When we do that we need less than half
the memory, and we have decreased the exit handling time for all guest exits,
at the cost of increased number of TLB misses because the host overwrites some
guest entries.
These savings will be increased on processors with larger TLBs or which
implement intelligent flush instructions like tlbivax (which will avoid the
need to walk arrays in software).
In addition to that and to the code simplification, we have a greater chance of
leaving other host userspace mappings in the TLB, instead of forcing all
subsequent tasks to re-fault all their mappings.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM currently ignores the host's round robin TLB eviction selection, instead
maintaining its own TLB state and its own round robin index. However, by
participating in the normal 44x TLB selection, we can drop the alternate TLB
processing in KVM. This results in a significant performance improvement,
since that processing currently must be done on *every* guest exit.
Accordingly, KVM needs to be able to access and increment tlb_44x_index.
(KVM on 440 cannot be a module, so there is no need to export this symbol.)
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM on 440 has always been able to handle large guest mappings with 4K host
pages -- we must, since the guest kernel uses 256MB mappings.
This patch makes KVM work when the host has large pages too (tested with 64K).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We used to defer invalidating userspace TLB entries until jumping out of the
kernel. This was causing MMU weirdness most easily triggered by using a pipe in
the guest, e.g. "dmesg | tail". I believe the problem was that after the guest
kernel changed the PID (part of context switch), the old process's mappings
were still present, and so copy_to_user() on the "return to new process" path
ended up using stale mappings.
Testing with large pages (64K) exposed the problem, probably because with 4K
pages, pressure on the TLB faulted all process A's mappings out before the
guest kernel could insert any for process B.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Bare metal Linux on 440 can "overmap" RAM in the kernel linear map, so that it
can use large (256MB) mappings even if memory isn't a multiple of 256MB. To
prevent the hardware prefetcher from loading from an invalid physical address
through that mapping, it's marked Guarded.
However, KVM must ensure that all guest mappings are backed by real physical
RAM (since a deliberate access through a guarded mapping could still cause a
machine check). Accordingly, we don't need to make our mappings guarded, so
let's allow prefetching as the designers intended.
Curiously this patch didn't affect performance at all on the quick test I
tried, but it's clearly the right thing to do anyways and may improve other
workloads.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Make sure that CONFIG_KVM cannot be selected without processor support
(currently, 440 is the only processor implementation available).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
set ESR[PTR] when emulating a guest trap. This allows Linux guests to
properly handle WARN_ON() (i.e. detect that it's a non-fatal trap).
Also remove debugging printk in trap emulation.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In kvmppc_deliver_interrupt is just one case left in the switch and it is a
rare one (less than 8%) when looking at the exit numbers. Therefore we can
at least drop the switch/case and if an if. I inserted an unlikely too, but
that's open for discussion.
In kvmppc_can_deliver_interrupt all frequent cases are in the default case.
I know compilers are smart but we can make it easier for them. By writing
down all options and removing the default case combined with the fact that
ithe values are constants 0..15 should allow the compiler to write an easy
jump table.
Modifying kvmppc_can_deliver_interrupt pointed me to the fact that gcc seems
to be unable to reduce priority_exception[x] to a build time constant.
Therefore I changed the usage of the translation arrays in the interrupt
delivery path completely. It is now using priority without translation to irq
on the full irq delivery path.
To be able to do that ivpr regs are stored by their priority now.
Additionally the decision made in kvmppc_can_deliver_interrupt is already
sufficient to get the value of interrupt_msr_mask[x]. Therefore we can replace
the 16x4byte array used here with a single 4byte variable (might still be one
miss, but the chance to find this in cache should be better than the right
entry of the whole array).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we use a unsigned long here anyway we can use the optimized __ffs.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we use an unnecessary if&switch to detect some cases.
To be honest we don't need the ligh_exits counter anyway, because we can
calculate it out of others. Sum_exits can also be calculated, so we can
remove that too.
MMIO, DCR and INTR can be counted on other places without these
additional control structures (The INTR case was never hit anyway).
The handling of BOOKE_INTERRUPT_EXTERNAL/BOOKE_INTERRUPT_DECREMENTER is
similar, but we can avoid the additional if when copying 3 lines of code.
I thought about a goto there to prevent duplicate lines, but rewriting three
lines should be better style than a goto cross switch/case statements (its
also not enough code to justify a new inline function).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When changing some msr bits e.g. problem state we need to take special
care of that. We call the function in our mtmsr emulation (not needed for
wrtee[i]), but we don't call kvmppc_set_msr if we change msr via set_regs
ioctl.
It's a corner case we never hit so far, but I assume it should be
kvmppc_set_msr in our arch set regs function (I found it because it is also
a corner case when using pv support which would miss the update otherwise).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
However, some of these fields could be split into separate per-core structures
in the future.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch doesn't yet move all 44x-specific data into the new structure, but
is the first step down that path. In the future we may also want to create a
struct kvm_vcpu_booke.
Based on patch from Liu Yu <yu.liu@freescale.com>.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cores provide 3 emulation hooks, implemented for example in the new
4xx_emulate.c:
kvmppc_core_emulate_op
kvmppc_core_emulate_mtspr
kvmppc_core_emulate_mfspr
Strictly speaking the last two aren't necessary, but provide for more
informative error reporting ("unknown SPR").
Long term I'd like to have instruction decoding autogenerated from tables of
opcodes, and that way we could aggregate universal, Book E, and core-specific
instructions more easily and without redundant switch statements.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This is used in a couple places in KVM, but isn't KVM-specific.
However, this patch doesn't modify other in-kernel emulation code:
- xmon uses a direct copy of ppc_opc.c from binutils
- emulate_instruction() doesn't need it because it can use a series
of mask tests.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This introduces a set of core-provided hooks. For 440, some of these are
implemented by booke.c, with the rest in (the new) 44x.c.
Note that these hooks are link-time, not run-time. Since it is not possible to
build a single kernel for both e500 and 440 (for example), using function
pointers would only add overhead.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The division was somewhat artificial and cumbersome, and had no functional
benefit anyways: we can only guests built for the real host processor.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will ease ports to other cores.
Also remove unused "struct kvm_tlb" while we're at it.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will make it easier to provide implementations for other cores.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The cpu time spent by the idle process actually doing something is
currently accounted as idle time. This is plain wrong, the architectures
that support VIRT_CPU_ACCOUNTING=y can do better: distinguish between the
time spent doing nothing and the time spent by idle doing work. The first
is accounted with account_idle_time and the second with account_system_time.
The architectures that use the account_xxx_time interface directly and not
the account_xxx_ticks interface now need to do the check for the idle
process in their arch code. In particular to improve the system vs true
idle time accounting the arch code needs to measure the true idle time
instead of just testing for the idle process.
To improve the tick based accounting as well we would need an architecture
primitive that can tell us if the pt_regs of the interrupted context
points to the magic instruction that halts the cpu.
In addition idle time is no more added to the stime of the idle process.
This field now contains the system time of the idle process as it should
be. On systems without VIRT_CPU_ACCOUNTING this will always be zero as
every tick that occurs while idle is running will be accounted as idle
time.
This patch contains the necessary common code changes to be able to
distinguish idle system time and true idle time. The architectures with
support for VIRT_CPU_ACCOUNTING need some changes to exploit this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The utimescaled / stimescaled fields in the task structure and the
global cpustat should be set on all architectures. On s390 the calls
to account_user_time_scaled and account_system_time_scaled never have
been added. In addition system time that is accounted as guest time
to the user time of a process is accounted to the scaled system time
instead of the scaled user time.
To fix the bugs and to prevent future forgetfulness this patch merges
account_system_time_scaled into account_system_time and
account_user_time_scaled into account_user_time.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Michael Neuling <mikey@neuling.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
stacktrace: provide save_stack_trace_tsk() weak alias
rcu: provide RCU options on non-preempt architectures too
printk: fix discarding message when recursion_bug
futex: clean up futex_(un)lock_pi fault handling
"Tree RCU": scalable classic RCU implementation
futex: rename field in futex_q to clarify single waiter semantics
x86/swiotlb: add default swiotlb_arch_range_needs_mapping
x86/swiotlb: add default phys<->bus conversion
x86: unify pci iommu setup and allow swiotlb to compile for 32 bit
x86: add swiotlb allocation functions
swiotlb: consolidate swiotlb info message printing
swiotlb: support bouncing of HighMem pages
swiotlb: factor out copy to/from device
swiotlb: add arch hook to force mapping
swiotlb: allow architectures to override phys<->bus<->phys conversions
swiotlb: add comment where we handle the overflow of a dma mask on 32 bit
rcu: fix rcutorture behavior during reboot
resources: skip sanity check of busy resources
swiotlb: move some definitions to header
swiotlb: allow architectures to override swiotlb pool allocation
...
Fix up trivial conflicts in
arch/x86/kernel/Makefile
arch/x86/mm/init_32.c
include/linux/hardirq.h
as per Ingo's suggestions.
Boards should know when QE_USB is used, so that they can configure USB
clocks and pins.
Another option would be to add 'select QE_USB' into USB_GADGET_FSL_QE,
but selects are evil since they don't support dependencies.
While at it, also remove 'host' from the symbol description, since the
QE_USB code is used to support the gadget driver as well.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a call to local_irq_restore in the normal exit case, so it would
seem that there should be one on an error return as well.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
expression E,E1,E2;
@@
local_irq_save(l);
... when != local_irq_restore(l)
when != spin_unlock_irqrestore(E,l)
when any
when strict
(
if (...) { ... when != local_irq_restore(l)
when != spin_unlock_irqrestore(E1,l)
+ local_irq_restore(l);
return ...;
}
|
if (...)
+ {local_irq_restore(l);
return ...;
+ }
|
spin_unlock_irqrestore(E2,l);
|
local_irq_restore(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The newest revision of uboot reworks the memory map for this
board to look more like the 85xx boards. Also, some regions
which were far larger than the actual hardware have been scaled
back to match the board, and the imaginary second flash bank has
been removed. Rapidio and PCI are mutually exclusive in the hardware,
and they now are occupying the same space in the address map.
The Rapidio node is commented out of the .dts since PCI is the
common use case.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some 83xx boards were not ready for the optional QUICC Engine support.
This patch fixes following build errors:
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb308): undefined reference to `par_io_data_set'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb334): undefined reference to `par_io_data_set'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb408): undefined reference to `qe_ic_get_high_irq'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb478): undefined reference to `qe_ic_get_low_irq'
arch/powerpc/platforms/built-in.o: In function `mpc832x_spi_init':
mpc832x_rdb.c:(.init.text+0x574c): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x5768): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x5784): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x57a0): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x57bc): undefined reference to `par_io_config_pin'
arch/powerpc/platforms/built-in.o:mpc832x_rdb.c:(.init.text+0x57d8): more undefined references to `par_io_config_pin' follow
arch/powerpc/platforms/built-in.o: In function `mpc836x_rdk_init_IRQ':
mpc836x_rdk.c:(.init.text+0x5e84): undefined reference to `qe_ic_init'
arch/powerpc/platforms/built-in.o: In function `mpc836x_rdk_setup_arch':
mpc836x_rdk.c:(.init.text+0x5f10): undefined reference to `qe_reset'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some 83xx boards were not ready for the optional QUICC Engine support.
This patch fixes following build errors:
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb308): undefined reference to `par_io_data_set'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb334): undefined reference to `par_io_data_set'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb408): undefined reference to `qe_ic_get_high_irq'
arch/powerpc/platforms/built-in.o: In function `flush_disable_caches':
(.text+0xb478): undefined reference to `qe_ic_get_low_irq'
arch/powerpc/platforms/built-in.o: In function `mpc832x_spi_init':
mpc832x_rdb.c:(.init.text+0x574c): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x5768): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x5784): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x57a0): undefined reference to `par_io_config_pin'
mpc832x_rdb.c:(.init.text+0x57bc): undefined reference to `par_io_config_pin'
arch/powerpc/platforms/built-in.o:mpc832x_rdb.c:(.init.text+0x57d8): more undefined references to `par_io_config_pin' follow
arch/powerpc/platforms/built-in.o: In function `mpc836x_rdk_init_IRQ':
mpc836x_rdk.c:(.init.text+0x5e84): undefined reference to `qe_ic_init'
arch/powerpc/platforms/built-in.o: In function `mpc836x_rdk_setup_arch':
mpc836x_rdk.c:(.init.text+0x5f10): undefined reference to `qe_reset'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes following sparse warnings:
CHECK fsl_pci.c
fsl_pci.c:32:13: warning: symbol 'setup_pci_atmu' was not declared. Should it be static?
fsl_pci.c:89:13: warning: symbol 'setup_pci_cmd' was not declared. Should it be static?
fsl_pci.c:133:12: warning: symbol 'fsl_pcie_check_link' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add the usb node to support USB host on the MPC8360E-RDK
boards.
Currently U-Boot doesn't fill the clock-frequency property for
timer nodes, so for now we have to fill it manually.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver supports very simple GPIO controllers, that is, when a
controller provides just a 'data' register. Such controllers may be
found in various BCSRs (Board's FPGAs used to control board's
switches, LEDs, chip-selects, Ethernet/USB PHY power, etc).
So far we support only 1-byte GPIO banks. Support for other widths may
be implemented when/if needed.
p.s.
To avoid "made up" compatible entries (like compatible = "simple-gpio"),
boards must call simple_gpiochip_init() to pass the compatible string.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this API we're able to set a QE pin to the GPIO mode or a dedicated
peripheral function.
The API relies on the fact that QE gpio controllers are registered. If
they aren't, the API won't work (gracefully though).
There is one caveat though: if anybody occupied the node->data before us,
or overwrote it, then bad things will happen. Luckily this is all in the
platform code that we fully control, so this should never happen.
I could implement more checks (for example we could create a list of
successfully registered QE controllers, and compare the node->data in the
qe_pin_request()), but this is unneeded if nobody is going to do silly
things behind our back.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes following sparse warnings:
CHECK 83xx/usb.c
83xx/usb.c:205:5: warning: symbol 'mpc837x_usb_cfg' was not declared. Should it be static?
CHECK 83xx/mpc831x_rdb.c
83xx/mpc831x_rdb.c:45:13: warning: symbol 'mpc831x_rdb_init_IRQ' was not declared. Should it be static?
CHECK 83xx/mpc832x_rdb.c
83xx/mpc832x_rdb.c:133:13: warning: symbol 'mpc832x_rdb_init_IRQ' was not declared. Should it be static?
CHECK 83xx/mpc832x_mds.c
83xx/mpc832x_mds.c:68:12: warning: Using plain integer as NULL pointer
83xx/mpc832x_mds.c:72:13: warning: incorrect type in assignment (different address spaces)
83xx/mpc832x_mds.c:72:13: expected unsigned char [usertype] *static [toplevel] bcsr_regs
83xx/mpc832x_mds.c:72:13: got void [noderef] <asn:2>*
83xx/mpc832x_mds.c:99:11: warning: incorrect type in argument 1 (different address spaces)
83xx/mpc832x_mds.c:99:11: expected void volatile [noderef] <asn:2>*addr
83xx/mpc832x_mds.c:99:11: got unsigned char [usertype] *static [toplevel] bcsr_regs
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to not bother with ugly #ifdefs in the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
This adds support for 16k and 64k page sizes on PowerPC 44x processors.
The PGDIR table is much smaller than a page when using 16k or 64k
pages (512 and 32 bytes respectively) so we allocate the PGDIR with
kzalloc() instead of __get_free_pages().
One PTE table covers rather a large memory area when using 16k or 64k
pages (32MB or 512MB respectively), so we can easily put FIXMAP and
PKMAP in the area covered by one PTE table.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vladimir Panfilov <pvr@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Ensure that total memory size is page-aligned, because otherwise
mark_bootmem() gets upset.
This error case was triggered by using 64 KiB pages in the kernel
while arch/powerpc/boot/4xx.c arbitrarily reduced the amount of memory
by 4096 (to work around a chip bug that affects the last 256 bytes of
physical memory).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (241 commits)
sched, trace: update trace_sched_wakeup()
tracing/ftrace: don't trace on early stage of a secondary cpu boot, v3
Revert "x86: disable X86_PTRACE_BTS"
ring-buffer: prevent false positive warning
ring-buffer: fix dangling commit race
ftrace: enable format arguments checking
x86, bts: memory accounting
x86, bts: add fork and exit handling
ftrace: introduce tracing_reset_online_cpus() helper
tracing: fix warnings in kernel/trace/trace_sched_switch.c
tracing: fix warning in kernel/trace/trace.c
tracing/ring-buffer: remove unused ring_buffer size
trace: fix task state printout
ftrace: add not to regex on filtering functions
trace: better use of stack_trace_enabled for boot up code
trace: add a way to enable or disable the stack tracer
x86: entry_64 - introduce FTRACE_ frame macro v2
tracing/ftrace: add the printk-msg-only option
tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()
x86, bts: correctly report invalid bts records
...
Fixed up trivial conflict in scripts/recordmcount.pl due to SH bits
being already partly merged by the SH merge.
Impact: New APIs
The old node_to_cpumask/node_to_pcibus returned a cpumask_t: these
return a pointer to a struct cpumask. Part of removing cpumasks from
the stack.
(Also replaces powerpc internal uses of node_to_cpumask).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch_setup_additional_pages currently gets two arguments, the binary
format descripton and an indication if the process uses an executable
stack or not. The second argument is not used by anybody, it could
be removed without replacement.
What actually does make sense is to pass an indication if the process
uses the elf interpreter or not. The glibc code will not use anything
from the vdso if the process does not use the dynamic linker, so for
statically linked binaries the architecture backend can choose not
to map the vdso.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Wire up the trampoline code for ppc32 to relay exceptions from the
vectors at address 0 to vectors at address 32MB, and modify Kconfig
to enable Kdump support for all classic powerpcs.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the ability for a classic ppc kernel to be loaded at an address
of 32MB. This done by fixing a few places that assume we are loaded
at address 0, and by changing several uses of KERNELBASE to use
PAGE_OFFSET, instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While for debugging it is good to catch bogus users of ioremap, though
for kdump support it is more convenient to use __ioremap for
copy_oldmem_page() (exactly as we do for PPC64 currently).
Note that copy_oldmem_page() calls __ioremap with flags set to '0',
so it should be safe with the regard to the caches.
The other option is to use kmap_atomic_pfn()[1], but it will not work
for kernels compiled without HIGHMEM.
That is, on a board with 256MB RAM and crashkernel=64M@32M case, the
!HIGHMEM capturing kernel maps 0-96M range, which does not include all
the memory needed to capture the dump. And, obviously, accessing
anything upper than 96M will cause faults.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2007-November/046747.html
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refactor the setting of kdump OF properties, moving the common code
from machine_kexec_64.c to machine_kexec.c where it can be used on
both ppc64 and ppc32. This will be needed for kdump to work on ppc32
platforms.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces the dummy crash_setup_regs function with full-fledged
crash_setup_regs implementation. On PPC32 we simply use the new
ppc_save_regs function to dump the registers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Today the arch/powerpc/xmon/setjmp.S file contains only the
xmon_save_regs function. We want to use it for kdump purposes, so
let's move the file into arch/powerpc/kernel/ and give the function a
more generic name (ppc_save_regs).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the need for each platform to specify default kexec and
crash kernel ops, thus effectively adds a working kexec support for
most 6xx/7xx/7xxx-based boards.
Platforms that can't cope with default ops will explode in some weird
way (a hang or reboot is most likely), which means that the board's
kexec support should be fixed or blacklisted via dummy _prepare
callback returning -ENOSYS.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refactor the setting of kexec OF properties, moving the common code
from machine_kexec_64.c to machine_kexec.c where it can be used on
both ppc64 and ppc32. This is needed for kexec to work on ppc32
platforms.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, pseries_cpu_die() calls msleep() while polling RTAS for
the status of the dying cpu.
However, if the cpu that is going down also happens to be the one
doing the tick then we're hosed as the tick_do_timer_cpu 'baton' is
only passed later on in tick_shutdown() when _cpu_down() does the
CPU_DEAD notification. Therefore jiffies won't be updated anymore.
This replaces that msleep() with a cpu_relax() to make sure we're not
going to schedule at that point.
With this patch my test box survives a 100k iterations hotplug stress
test on _all_ cpus, whereas without it, it quickly dies after ~50
iterations.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 2a4aca1144 ("powerpc/mm: Split
low level tlb invalidate for nohash processors") changed a call to
_tlbia to _tlbil_all but didn't include the header that defines
_tlbil_all, leading to a build failure on 440 if KVM is enabled.
This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the QPACE (Chromodynamics Parallel Computing on the
Cell Broadband Engine) platform doesn't use a iommu, doesn't
have PCI devices and a MPIC much lesser setup and
configurations are needed. So far all devices are detected
as OF device. A notifier function is used to set the dma_ops
for the of_platform bus. Further this patch splits the
PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are
shared with the QPACE platform and the rest.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CBE_THERM and OPROFILE_CELL both cannot be built without
SPU_FS disabled, so make the dependency explicit.
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add RTS/CTS-support for the PSC of the MPC5200B. Tested with a Phytec
MPC5200B-IO.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds MDMA/UDMA support using BestComm for DMA on the MPC5200
platform. Based heavily on previous work by Freescale (Bernard Kuhn,
John Rigby) and Domen Puncer.
With this patch, a SanDisk Extreme IV CF card gets read speeds of
approximately 26.70 MB/sec.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When ATA DMA is enabled, bestcomm prefetching does not work. This
patch adds a function to disable bestcomm prefetch when the ATA
Bestcomm task is initialized.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1) ata.h has dst_pa in the wrong place (needs to match what the BestComm
task microcode in bcom_ata_task.c expects); fix it.
2) The BestComm ATA task priority was changed to maximum in bestcomm_priv.h;
this fixes a deadlock issue experienced with heavy DMA occurring on
both the ATA and Ethernet BestComm tasks, e.g. when downloading a large
file over a LAN to disk.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The buffer descriptors for the ATA BestComm task are larger than the
current definition for bcom_bd. This causes problems because the
various bcom_... functions dereference the buffer descriptor pointer
by using the array operator which doesn't work when the buffer
descriptors are a different size.
This patch adds the bcom_get_bd() function which uses the value in
bcom_task.bd_size to calculate the offset into the BD table. This
patch also changes the definition of bcom_bd to specify a data size
of 0 instead of 1 so that it will never work if anyone attempts to
dereference the bd list as an array (as opposed to something that
might work even though it is wrong).
Finally, this patch moves the definition of bcom_bd up in the file
to eliminate a forward declaration.
Based on patch originally written by Tim Yamin.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The MPC5200 internal interrupt controller setup function needs to set
the default interrupt controller when it is called. Without this
irq_create_of_mapping() cannot be called without first determining
the pointer to the irq controller (ie. call with controller = NULL).
Reported-by: Steven Cavanagh <scavanagh@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds documentation to the mpc5200 interrupt controller
driver and cleans up some minor coding conventions. It also moves the
contents of mpc52xx_pic.h into the driver proper (except for a small
common bit that is moved to the common mpc52xx.h) because the
information encoded there is not required by any other part of kernel
code. Finally for code readability sake, the L2_OFFSET shift value
is removed because the code using it resolves to a noop.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rework to MMU code dropped a much missed 'blr' instruction.
Brown-Paper-Bag-Worn-By: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The correct #address-cells was still used for the actual translation,
so the impact is only a possibility of choosing the wrong range entry
or failing to find any match. Most common cases were not affected.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add const qualifier to device_node argument for
dcr_resource_{start,len} as of_get_property also const-qualifies this
argument.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After discussing with chip designers, it appears that it's not
necessary to set G everywhere on 440 cores. The various core
errata related to prefetch should be sorted out by firmware by
disabling icache prefetching in CCR0. We add the workaround to
the kernel however just in case oooold firmwares don't do it.
This is valid for -all- 4xx core variants. Later ones hard wire
the absence of prefetch but it doesn't harm to clear the bits
in CCR0 (they should already be cleared anyway).
We still leave G=1 on the linear mapping for now, we need to
stop over-mapping RAM to be able to remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, we never set _PAGE_COHERENT in the PTEs, we just OR it in
in the hash code based on some CPU feature bit. We also manipulate
_PAGE_NO_CACHE and _PAGE_GUARDED by hand in all sorts of places.
This changes the logic so that instead, the PTE now contains
_PAGE_COHERENT for all normal RAM pages thay have I = 0 on platforms
that need it. The hash code clears it if the feature bit is not set.
It also adds some clean accessors to setup various valid combinations
of access flags and change various bits of code to use them instead.
This should help having the PTE actually containing the bit
combinations that we really want.
I also removed _PAGE_GUARDED from _PAGE_BASE on 44x and instead
set it explicitely from the TLB miss. I will ultimately remove it
completely as it appears that it might not be needed after all
but in the meantime, having it in the TLB miss makes things a
lot easier.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the MMU context code used for CPUs with no hash table
(except 603) dynamically allocate the various maps used to track
the state of contexts.
Only the main free map and CPU 0 stale map are allocated at boot
time. Other CPU maps are allocated when those CPUs are brought up
and freed if they are unplugged.
This also moves the initialization of the MMU context management
slightly later during the boot process, which should be fine as
it's really only needed when userland if first started anyways.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The handlers for Critical, Machine Check or Debug interrupts
will save and restore MMUCR nowadays, thus we only need to
disable normal interrupts when invalidating TLB entries.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the various forms of low level TLB invalidations are all
implemented in misc_32.S for 32-bit processors, in a fairly scary
mess of #ifdef's and with interesting duplication such as a whole
bunch of code for FSL _tlbie and _tlbia which are no longer used.
This moves things around such that _tlbie is now defined in
hash_low_32.S and is only used by the 32-bit hash code, and all
nohash CPUs use the various _tlbil_* forms that are now moved to
a new file, tlb_nohash_low.S.
I moved all the definitions for that stuff out of
include/asm/tlbflush.h as they are really internal mm stuff, into
mm/mmu_decl.h
The code should have no functional changes. I kept some variants
inline for trivial forms on things like 40x and 8xx.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This commit moves the whole no-hash TLB handling out of line into a
new tlb_nohash.c file, and implements some basic SMP support using
IPIs and/or broadcast tlbivax instructions.
Note that I'm using local invalidations for D->I cache coherency.
At worst, if another processor is trying to execute the same and
has the old entry in its TLB, it will just take a fault and re-do
the TLB flush locally (it won't re-do the cache flush in any case).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We're soon running out of CPU features and I need to add some new
ones for various MMU related bits, so this patch separates the MMU
features from the CPU features. I moved over the 32-bit MMU related
ones, added base features for MMU type families, but didn't move
over any 64-bit only feature yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reworks the context management code used by 4xx,8xx and
freescale BookE. It adds support for SMP by implementing a
concept of stale context map to lazily flush the TLB on
processors where a context may have been invalidated. This
also contains the ground work for generalizing such lazy TLB
flushing by just picking up a new PID and marking the old one
stale. This will be implemented later.
This is a first implementation that uses a global spinlock.
Ideally, we should try to get at least the fast path (context ID
already assigned) lockless or limited to a per context lock,
but for now this will do.
I tried to keep the UP case reasonably simple to avoid adding
too much overhead to 8xx which does a lot of context stealing
since it effectively has only 16 PIDs available.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits the mmu_context handling between 32-bit hash based
processors, 64-bit hash based processors and everybody else. This is
preliminary work for adding SMP support for BookE processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds supports to the "extended" DCR addressing via the indirect
mfdcrx/mtdcrx instructions supported by some 4xx cores (440H6 and
later).
I enabled the feature for now only on AMCC 460 chips.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When running Active Memory Sharing, pages can get marked as
"loaned" with the hypervisor by the CMM driver. This state gets
cleared by the system firmware when rebooting the partition.
When using kexec to boot a new kernel, this state never gets
cleared and the hypervisor and CMM driver can get out of sync
with respect to the number of pages currently marked "loaned".
Fix this by adding a reboot notifier to the CMM driver to deflate
the balloon and mark all pages as active.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When running Active Memory Sharing, the Collaborative Memory Manager
(CMM) may mark some pages as "loaned" with the hypervisor.
Periodically, the CMM will query the hypervisor for a loan request,
which is a single signed value. When kexec'ing into a kdump kernel,
the CMM driver in the kdump kernel is not aware of the pages the
previous kernel had marked as "loaned", so the hypervisor and the CMM
driver are out of sync. This results in the CMM driver getting a
negative loan request, which can then get treated as a large unsigned
value and can cause kdump to hang due to the CMM driver inflating too
large. Since there really is no clean way for the CMM driver in the
kdump kernel to clean this up, simply disable CMM in the kdump kernel.
This fixes hangs we were seeing doing kdump with AMS.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Otherwise you get lot of errors like these:
drivers/block/viodasd.c:72: error: dereferencing pointer to incomplete type
drivers/block/viodasd.c: In function 'viodasd_open':
drivers/block/viodasd.c:135: error: dereferencing pointer to incomplete type
drivers/block/viodasd.c: In function 'viodasd_release':
drivers/block/viodasd.c:184: error: dereferencing pointer to incomplete type
drivers/block/viodasd.c: In function 'viodasd_getgeo':
drivers/block/viodasd.c:209: error: dereferencing pointer to incomplete type
drivers/block/viodasd.c:214: error: implicit declaration of function 'get_capacity'
drivers/block/viodasd.c: At top level:
drivers/block/viodasd.c:222: error: variable 'viodasd_fops' has initializer but incomplete type
drivers/block/viodasd.c:223: error: unknown field 'owner' specified in initializer
Discovered by a randconfig build.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ibm_configure_kernel_dump is passed as the token to rtas_call() is
never initialised. This sets it to something sane.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Manish Ahuja <mahujam@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
print_dump_header() will be called at least once with a NULL pointer in
a normal boot sequence. If DEBUG is defined then we will dereference
the pointer and crash. Add a quick fix to exit early in the NULL pointer
case.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Manish Ahuja <mahujam@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename PowerPC's struct vm_region so that I can introduce my own
global version for NOMMU. It's feasible that the PowerPC version may
wish to use my global one instead.
The NOMMU vm_region struct defines areas of the physical memory map
that are under mmap. This may include chunks of RAM or regions of
memory mapped devices, such as flash. It is also used to retain
copies of file content so that shareable private memory mappings of
files can be made. As such, it may be compatible with what is
described in the banner comment for PowerPC's vm_region struct.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using the common code means that more complete cache information will
provided in sysfs on platforms that don't use the l2-cache property
convention.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The smp code uses cache information to populate cpu_core_map; change
it to use common code for cache lookup.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have more than one piece of code that looks up cache nodes manually
using the "l2-cache" property. Add a common helper routine which does
this and handles ePAPR's "next-level-cache" property as well as
powermac.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a long-standing performance bug in classic RCU that
results in massive internal-to-RCU lock contention on systems with
more than a few hundred CPUs. Although this patch creates a separate
flavor of RCU for ease of review and patch maintenance, it is intended
to replace classic RCU.
This patch still handles stress better than does mainline, so I am still
calling it ready for inclusion. This patch is against the -tip tree.
Nevertheless, experience on an actual 1000+ CPU machine would still be
most welcome.
Most of the changes noted below were found while creating an rcutiny
(which should permit ejecting the current rcuclassic) and while doing
detailed line-by-line documentation.
Updates from v9 (http://lkml.org/lkml/2008/12/2/334):
o Fixes from remainder of line-by-line code walkthrough,
including comment spelling, initialization, undesirable
narrowing due to type conversion, removing redundant memory
barriers, removing redundant local-variable initialization,
and removing redundant local variables.
I do not believe that any of these fixes address the CPU-hotplug
issues that Andi Kleen was seeing, but please do give it a whirl
in case the machine is smarter than I am.
A writeup from the walkthrough may be found at the following
URL, in case you are suffering from terminal insomnia or
masochism:
http://www.kernel.org/pub/linux/kernel/people/paulmck/tmp/rcutree-walkthrough.2008.12.16a.pdf
o Made rcutree tracing use seq_file, as suggested some time
ago by Lai Jiangshan.
o Added a .csv variant of the rcudata debugfs trace file, to allow
people having thousands of CPUs to drop the data into
a spreadsheet. Tested with oocalc and gnumeric. Updated
documentation to suit.
Updates from v8 (http://lkml.org/lkml/2008/11/15/139):
o Fix a theoretical race between grace-period initialization and
force_quiescent_state() that could occur if more than three
jiffies were required to carry out the grace-period
initialization. Which it might, if you had enough CPUs.
o Apply Ingo's printk-standardization patch.
o Substitute local variables for repeated accesses to global
variables.
o Fix comment misspellings and redundant (but harmless) increments
of ->n_rcu_pending (this latter after having explicitly added it).
o Apply checkpatch fixes.
Updates from v7 (http://lkml.org/lkml/2008/10/10/291):
o Fixed a number of problems noted by Gautham Shenoy, including
the cpu-stall-detection bug that he was having difficulty
convincing me was real. ;-)
o Changed cpu-stall detection to wait for ten seconds rather than
three in order to reduce false positive, as suggested by Ingo
Molnar.
o Produced a design document (http://lwn.net/Articles/305782/).
The act of writing this document uncovered a number of both
theoretical and "here and now" bugs as noted below.
o Fix dynticks_nesting accounting confusion, simplify WARN_ON()
condition, fix kerneldoc comments, and add memory barriers
in dynticks interface functions.
o Add more data to tracing.
o Remove unused "rcu_barrier" field from rcu_data structure.
o Count calls to rcu_pending() from scheduling-clock interrupt
to use as a surrogate timebase should jiffies stop counting.
o Fix a theoretical race between force_quiescent_state() and
grace-period initialization. Yes, initialization does have to
go on for some jiffies for this race to occur, but given enough
CPUs...
Updates from v6 (http://lkml.org/lkml/2008/9/23/448):
o Fix a number of checkpatch.pl complaints.
o Apply review comments from Ingo Molnar and Lai Jiangshan
on the stall-detection code.
o Fix several bugs in !CONFIG_SMP builds.
o Fix a misspelled config-parameter name so that RCU now announces
at boot time if stall detection is configured.
o Run tests on numerous combinations of configurations parameters,
which after the fixes above, now build and run correctly.
Updates from v5 (http://lkml.org/lkml/2008/9/15/92, bad subject line):
o Fix a compiler error in the !CONFIG_FANOUT_EXACT case (blew a
changeset some time ago, and finally got around to retesting
this option).
o Fix some tracing bugs in rcupreempt that caused incorrect
totals to be printed.
o I now test with a more brutal random-selection online/offline
script (attached). Probably more brutal than it needs to be
on the people reading it as well, but so it goes.
o A number of optimizations and usability improvements:
o Make rcu_pending() ignore the grace-period timeout when
there is no grace period in progress.
o Make force_quiescent_state() avoid going for a global
lock in the case where there is no grace period in
progress.
o Rearrange struct fields to improve struct layout.
o Make call_rcu() initiate a grace period if RCU was
idle, rather than waiting for the next scheduling
clock interrupt.
o Invoke rcu_irq_enter() and rcu_irq_exit() only when
idle, as suggested by Andi Kleen. I still don't
completely trust this change, and might back it out.
o Make CONFIG_RCU_TRACE be the single config variable
manipulated for all forms of RCU, instead of the prior
confusion.
o Document tracing files and formats for both rcupreempt
and rcutree.
Updates from v4 for those missing v5 given its bad subject line:
o Separated dynticks interface so that NMIs and irqs call separate
functions, greatly simplifying it. In particular, this code
no longer requires a proof of correctness. ;-)
o Separated dynticks state out into its own per-CPU structure,
avoiding the duplicated accounting.
o The case where a dynticks-idle CPU runs an irq handler that
invokes call_rcu() is now correctly handled, forcing that CPU
out of dynticks-idle mode.
o Review comments have been applied (thank you all!!!).
For but one example, fixed the dynticks-ordering issue that
Manfred pointed out, saving me much debugging. ;-)
o Adjusted rcuclassic and rcupreempt to handle dynticks changes.
Attached is an updated patch to Classic RCU that applies a hierarchy,
greatly reducing the contention on the top-level lock for large machines.
This passes 10-hour concurrent rcutorture and online-offline testing on
128-CPU ppc64 without dynticks enabled, and exposes some timekeeping
bugs in presence of dynticks (exciting working on a system where
"sleep 1" hangs until interrupted...), which were fixed in the
2.6.27 kernel. It is getting more reliable than mainline by some
measures, so the next version will be against -tip for inclusion.
See also Manfred Spraul's recent patches (or his earlier work from
2004 at http://marc.info/?l=linux-kernel&m=108546384711797&w=2).
We will converge onto a common patch in the fullness of time, but are
currently exploring different regions of the design space. That said,
I have already gratefully stolen quite a few of Manfred's ideas.
This patch provides CONFIG_RCU_FANOUT, which controls the bushiness
of the RCU hierarchy. Defaults to 32 on 32-bit machines and 64 on
64-bit machines. If CONFIG_NR_CPUS is less than CONFIG_RCU_FANOUT,
there is no hierarchy. By default, the RCU initialization code will
adjust CONFIG_RCU_FANOUT to balance the hierarchy, so strongly NUMA
architectures may choose to set CONFIG_RCU_FANOUT_EXACT to disable
this balancing, allowing the hierarchy to be exactly aligned to the
underlying hardware. Up to two levels of hierarchy are permitted
(in addition to the root node), allowing up to 16,384 CPUs on 32-bit
systems and up to 262,144 CPUs on 64-bit systems. I just know that I
am going to regret saying this, but this seems more than sufficient
for the foreseeable future. (Some architectures might wish to set
CONFIG_RCU_FANOUT=4, which would limit such architectures to 64 CPUs.
If this becomes a real problem, additional levels can be added, but I
doubt that it will make a significant difference on real hardware.)
In the common case, a given CPU will manipulate its private rcu_data
structure and the rcu_node structure that it shares with its immediate
neighbors. This can reduce both lock and memory contention by multiple
orders of magnitude, which should eliminate the need for the strange
manipulations that are reported to be required when running Linux on
very large systems.
Some shortcomings:
o More bugs will probably surface as a result of an ongoing
line-by-line code inspection.
Patches will be provided as required.
o There are probably hangs, rcutorture failures, &c. Seems
quite stable on a 128-CPU machine, but that is kind of small
compared to 4096 CPUs. However, seems to do better than
mainline.
Patches will be provided as required.
o The memory footprint of this version is several KB larger
than rcuclassic.
A separate UP-only rcutiny patch will be provided, which will
reduce the memory footprint significantly, even compared
to the old rcuclassic. One such patch passes light testing,
and has a memory footprint smaller even than rcuclassic.
Initial reaction from various embedded guys was "it is not
worth it", so am putting it aside.
Credits:
o Manfred Spraul for ideas, review comments, and bugs spotted,
as well as some good friendly competition. ;-)
o Josh Triplett, Ingo Molnar, Peter Zijlstra, Mathieu Desnoyers,
Lai Jiangshan, Andi Kleen, Andy Whitcroft, and Andrew Morton
for reviews and comments.
o Thomas Gleixner for much-needed help with some timer issues
(see patches below).
o Jon M. Tollefson, Tim Pepper, Andrew Theurer, Jose R. Santos,
Andy Whitcroft, Darrick Wong, Nishanth Aravamudan, Anton
Blanchard, Dave Kleikamp, and Nathan Lynch for keeping machines
alive despite my heavy abuse^Wtesting.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is an error in rh_alloc_fixed() of the Remote Heap code:
If there is at least one free block blk won't be NULL at the end of the
search loop, so -ENOMEM won't be returned and the else branch of
"if (bs == s || be == e)" will be taken, corrupting the management
structures.
Signed-off-by: Guillaume Knispel <gknispel@proformatique.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function flush_HPTE() is used in only one place, the implementation
of DEBUG_PAGEALLOC on ppc32.
It's actually a dup of flush_tlb_page() though it's -slightly- more
efficient on hash based processors. We remove it and replace it by
a direct call to the hash flush code on those processors and to
flush_tlb_page() for everybody else.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This renames the files to clarify the fact that they are used by
the hash based family of CPUs (the 603 being an exception in that
family but is still handled by that code).
This paves the way for the new tlb_nohash.c coming via a subsequent
commit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a local_flush_tlb_mm() call as a pre-requisite for some
SMP work for BookE processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of not defining it at all, this defines the macro as
being empty, thus avoiding ifdef's in call sites when CONFIG_BUG
is not set.
Also removes an extra whitespace in the existing definition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The block layer dropped the virtual merge feature
(b8b3e16cfe). BIO_VMERGE_BOUNDARY
definition is meaningless now (For POWER, BIO_VMERGE_BOUNDARY has been
meaningless for a long time since POWER disables the virtual merge
feature).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently there are a number of platforms that open code access to
the ppc_pci_flags global variable. However, that variable is not
present if CONFIG_PCI is not set, which can lead to a build break.
This introduces a number of accessor functions that are defined
to be empty in the case of CONFIG_PCI being disabled. The
various platform files in the kernel are updated to use these.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since "Factor out cpu joining/unjoining the GIQ"
(b4963255ad) the WARN_ON in
xics_set_cpu_giq() is being triggered during boot on JS20 because the
GIQ indicator is not available on that platform. While the warning is
harmless and the system runs normally, it's nicer to check for the
existence of the indicator before trying to manipulate it.
Implement rtas_indicator_present(), which searches the
/rtas/rtas-indicators property for the given indicator token, and use
this function in xics_set_cpu_giq().
Also use a WARN statement in xics_set_cpu_giq to get better
information on failure.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The hard_smp_processor_id functions are the appropriate interfaces for
managing physical CPU ids.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_hw_index isn't used on 64-bit, so move it from smp.c to
setup_32.c.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The `have_of' variable is a relic from the arch/ppc time, it isn't
useful nowadays.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change #define stubs of dma_sync ops to be empty static inlines
to avoid build warning.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 059e4938f8 ("powerpc/ps3: Add a sub-match
id to ps3_system_bus") forgot to update the module alias support:
- Add the sub-match ids to the module aliases, so udev can distinguish
between different types of sub-devices.
- Rename PS3_MODULE_ALIAS_GRAPHICS to PS3_MODULE_ALIAS_GPU_FB, as ps3fb
binds to the "FB" sub-device.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the debug message in dma_sb_region_create() from
pr_info() to DBG() to quiet the dmesg output.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a minor comment typo in pgtable-ppc64.h.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_put is needed before discarding a value received from
of_find_node_by_name, eg in error handling code or when the device
node is no longer used.
The semantic match that catches the bug is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression struct device_node *n;
position p1, p2;
statement S1,S2;
expression E,E1;
expression *ptr != NULL;
@@
(
if (!(n@p1 = of_find_node_by_name(...))) S1
|
n@p1 = of_find_node_by_name(...)
)
<... when != of_node_put(n)
when != if (...) { <+... of_node_put(n) ...+> }
when != true !n || ...
when != n = E
when != E = n
if (!n || ...) S2
...>
(
return \(0\|<+...n...+>\|ptr\);
|
return@p2 ...;
|
n = E1
|
E1 = n
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s of_find_node_by_name %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit d015fe995 'powerpc/cell/axon-msi: Retry on missing interrupt'
has turned a rare failure to kexec on QS22 into a reproducible
error, which we have now analysed.
The problem is that after a kexec, the MSIC hardware still points
into the middle of the old ring buffer. We set up the ring buffer
during reboot, but not the offset into it. On older kernels, this
would cause a storm of thousands of spurious interrupts after a
kexec, which would most of the time get dropped silently.
With the new code, we time out on each interrupt, waiting for
it to become valid. If more interrupts come in that we time
out on, this goes on indefinitely, which eventually leads to
a hard crash.
The solution in this commit is to read the current offset from
the MSIC when reinitializing it. This now works correctly, as
expected.
Reported-by: Dirk Herrendoerfer <d.herrendoerfer@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
careful_allocation() was calling into the bootmem allocator for
nodes which had not been fully initialized and caused a previous
bug: http://patchwork.ozlabs.org/patch/10528/ So, I merged a
few broken out loops in do_init_bootmem() to fix it. That changed
the code ordering.
I think this bug is triggered by having reserved areas for a node
which are spanned by another node's contents. In the
mark_reserved_regions_for_nid() code, we attempt to reserve the
area for a node before we have allocated the NODE_DATA() for that
nid. We do this since I reordered that loop. I suck.
This is causing crashes at bootup on some systems, as reported
by Jon Tollefson.
This may only present on some systems that have 16GB pages
reserved. But, it can probably happen on any system that is
trying to reserve large swaths of memory that happen to span other
nodes' contents.
This commit ensures that we do not touch bootmem for any node which
has not been initialized, and also removes a compile warning about
an unused variable.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It looks like most of the hugetlb code is doing the correct thing if
hugepages are not supported, but the mmap code is not. If we get into
the mmap code when hugepages are not supported, such as in an LPAR
which is running Active Memory Sharing, we can oops the kernel. This
fixes the oops being seen in this path.
oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=1024 NUMA pSeries
Modules linked in: nfs(N) lockd(N) nfs_acl(N) sunrpc(N) ipv6(N) fuse(N) loop(N)
dm_mod(N) sg(N) ibmveth(N) sd_mod(N) crc_t10dif(N) ibmvscsic(N)
scsi_transport_srp(N) scsi_tgt(N) scsi_mod(N)
Supported: No
NIP: c000000000038d60 LR: c00000000003945c CTR: c0000000000393f0
REGS: c000000077e7b830 TRAP: 0300 Tainted: G
(2.6.27.5-bz50170-2-ppc64)
MSR: 8000000000009032 <EE,ME,IR,DR> CR: 44000448 XER: 20000001
DAR: c000002000af90a8, DSISR: 0000000040000000
TASK = c00000007c1b8600[4019] 'hugemmap01' THREAD: c000000077e78000 CPU: 6
GPR00: 0000001fffffffe0 c000000077e7bab0 c0000000009a4e78 0000000000000000
GPR04: 0000000000010000 0000000000000001 00000000ffffffff 0000000000000001
GPR08: 0000000000000000 c000000000af90c8 0000000000000001 0000000000000000
GPR12: 000000000000003f c000000000a73880 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000010000
GPR20: 0000000000000000 0000000000000003 0000000000010000 0000000000000001
GPR24: 0000000000000003 0000000000000000 0000000000000001 ffffffffffffffb5
GPR28: c000000077ca2e80 0000000000000000 c00000000092af78 0000000000010000
NIP [c000000000038d60] .slice_get_unmapped_area+0x6c/0x4e0
LR [c00000000003945c] .hugetlb_get_unmapped_area+0x6c/0x80
Call Trace:
[c000000077e7bbc0] [c00000000003945c] .hugetlb_get_unmapped_area+0x6c/0x80
[c000000077e7bc30] [c000000000107e30] .get_unmapped_area+0x64/0xd8
[c000000077e7bcb0] [c00000000010b140] .do_mmap_pgoff+0x140/0x420
[c000000077e7bd80] [c00000000000bf5c] .sys_mmap+0xc4/0x140
[c000000077e7be30] [c0000000000086b4] syscall_exit+0x0/0x40
Instruction dump:
fac1ffb0 fae1ffb8 fb01ffc0 fb21ffc8 fb41ffd0 fb61ffd8 fb81ffe0 fbc1fff0
fbe1fff8 f821fef1 f8c10158 f8e10160 <7d49002e> f9010168 e92d01b0 eb4902b0
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the localbus reg & range properties to respect that the top
level #address-cells and #size-cells = 2. The original commit
(c64ef80b51) did not do that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We were missing the CPU_FTR_NOEXECUTE bit in our cputable for all
these processors. The result is that update_mmu_cache() would flush
the cache for all pages mapped to userspace which is totally
unnecessary on those processors since we already handle flushing
on execute in the page fault path.
This should provide a nice speed up ;-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
An example calling sequence which we did see:
copy_user_highpage -> kmap_atomic -> flush_tlb_page -> _tlbil_va
We got interrupted after setting up the MAS registers before the
tlbwe and the interrupt handler that caused the interrupt also did
a kmap_atomic (ide code) and thus on returning from the interrupt
the MAS registers no longer contained the proper values.
Since we dont save/restore MAS registers for normal interrupts we
need to disable interrupts in _tlbil_va to ensure atomicity.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: change calling convention of existing cpumask APIs
Most cpumask functions started with cpus_: these have been replaced by
cpumask_ ones which take struct cpumask pointers as expected.
These four functions don't have good replacement names; fortunately
they're rarely used, so we just change them over.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: paulus@samba.org
Cc: mingo@redhat.com
Cc: tony.luck@intel.com
Cc: ralf@linux-mips.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: cl@linux-foundation.org
Cc: srostedt@redhat.com
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
With this patch the L2 cache is enabled on Canyonlands to increase the
overall performance. There is a known cache coherency issue with the L2
cache, but this is related to the high bandwidth (HB) PLB segment where
the memory address is 0x8.xxxx.xxxx (low bandwidth PLB segment is mapped
to 0x0.xxxx.xxxx). Since this HB address is currently unused it is safe
to enable the L2 cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The cuboot-acadia.c wrapper can cause assembler errors on some
toolchains due to the lack of the proper BOOTCFLAGS. This adds
the proper flags for the file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 440x5 core in the Virtex5 uses the 440A type machine check
(ie, they have MCSRR0/MCSRR1). They thus need to call the
appropriate fixup function to hook the right variant of the
exception.
Without this, all machine checks become fatal due to loss
of context when entering the exception handler.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is needed so that Vitesse 7385 5-port switch could work on
MPC8349E-mITX boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This removes CONFIG_PCI_LEGACY (which is not needed) and consequently
several compiler warnings.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
KVM host support was recently enabled in ppc44x_defconfig, but since then the
config option was renamed. Update ppc44x_defconfig to match.
Also, KVM guests aren't very interesting without networking, so enable
CONFIG_TUN and CONFIG_BRIDGE.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
This patch creates the dts files for each core and splits the devices
between the two cores for MPC8572DS.
core0 has memory, L2, i2c, dma1, global-util, eth0, eth1, crypto, pci0, pci1.
core1 has L2, dma2, eth2, eth3, pci2, msi.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The flag MPIC_WANTS_RESET shouldn't be set if we are doing cooperative
asymmetric MP. The second linux shouldn't reset the pic or the first
one gets very confused.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add NOR and NAND flash partitions for mpc8572ds board
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic support for the GPIO available on the SBC610 VPX Single Board Computer
from GE Fanuc (PowerPC MPC8641D).
This patch adds basic support for the GPIO in the devices I/O FPGA, the GPIO
functionality is exposed through the AFIX pins on the backplane, unless used
by an AFIX card.
This code currently does not support switching between totem-pole and
open-drain outputs (when used as outputs, GPIOs default to totem-pole).
The interrupt capabilites of the GPIO lines is also not currently supported.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch we can compile the qe_lib/usb.c without the UCC
support (that is, without UCC_GETH and/or SERIAL_QE).
Fixes following link error (CONFIG_SMP should be =y to trigger this):
arch/powerpc/sysdev/built-in.o: In function `qe_usb_clock_set':
(.text+0x3cae): undefined reference to `cmxgcr_lock'
make: *** [.tmp_vmlinux1] Error 1
While at it, also add missing spinlock.h includes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding use of newly added Epson RTX-8581 real-time clock driver to GE
Fanuc SBC610's dts file and adding driver to default config.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/mpc85xx_mds.c: In function 'board_fixups':
arch/powerpc/platforms/85xx/mpc85xx_mds.c:244: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
arch/powerpc/platforms/85xx/mpc85xx_mds.c:250: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added 85xx specifc smp_ops structure. We use ePAPR style boot release
and the MPIC for IPIs at this point.
Additionally added routines for secondary cpu entry and initializtion.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The initial TLB mapping for the kernel boot didn't set the memory coherent
attribute, MAS2[M], in SMP mode.
If this code supported booting a secondary processor, which it doesn't yet,
but if it did, then when a secondary processor boots, it would probably signal
the primary processor by setting a variable called something like
__secondary_hold_acknowledge. However, due to the lack of the M bit, the
primary processor would not snoop the transaction (even if a transaction were
broadcast). If primary CPU's L1 D-cache had a copy, it would not be flushed
and the CPU would never see the ack. Which would have resulted in the primary
CPU spinning for a long time, perhaps a full second before it gives up, while
it would have waited for the ack from the secondary CPU that it wouldn't have
been able to see because of the stale cache.
The value of MAS2 for the boot page TLB1 entry is a compile time constant,
so there is no need to calculate it in powerpc assembly language.
Also, from the MPC8572 manual section 6.12.5.3, "Bits that represent
offsets within a page are ignored and should be cleared." Existing code
didn't clear them, this code does.
The same when the page of KERNELBASE is found; we don't need to use asm to
mask the lower 12 bits off.
In the code that computes the address to rfi from, don't hard code the
offset to 24 bytes, but have the assembler figure that out for us.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch add the handlers of SPE/EFP exceptions.
The code is used to emulate float point arithmetic,
when MSR(SPE) is enabled and receive EFP data interrupt or EFP round interrupt.
This patch has no conflict with or dependence on FP math-emu.
The code has been tested by TestFloat.
Now the code doesn't support SPE/EFP instructions emulation
(it won't be called when receive program interrupt),
but it could be easily added.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FP_DECL_EX is already used, so ret is redundant.
And FP_SET_EXCEPTION will add status into return value.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using the same macro definition for _FP_CHOOSENAN as s390,
sh, sparc32/64. The original author didn't understand this and
matched what sparc64 was doing and they have updated to this definition.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PowerPC float point division emulation is derived from gcc.
I reported this problem on gcc maillist and got this reply:
http://gcc.gnu.org/ml/gcc/2008-03/msg00543.html
Since UDIV_NEEDS_NORMALIZATION is not used by kernel, we should use
_FP_DIV_MEAT_1_udiv_norm to make sure the single float point
is normalized before udiv_qrnnd.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After testing of various compiler flag combinations by Nate Case it was
determined that -mabi=no-spe has no impact on the compiler generating
SPE instructions. Only -mno-spe and -mspe=no do.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The name of the device_node field differ across the platforms, so we
have to implement inlined accessors. This is needed to avoid ugly
#ifdef in the generic code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ibmebus_free_irq() frees the IRQ but does not remove its mapping, which
results in stale entries in the map.
This fixes it by adding a call to irq_dispose_mapping() in
ibmebus_free_irq().
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As noted by Akinobu Mita in commit b1fceac2 ("x86: remove unnecessary
memset and NULL check after alloc_bootmem()"), alloc_bootmem and
related functions never return NULL and always return a zeroed region
of memory. Thus a NULL test or memset after calls to these functions
is unnecessary.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to swap these out once we start using swiotlb, so add
them to dma_ops. Create CONFIG_PPC_NEED_DMA_SYNC_OPS Kconfig
option; this is currently enabled automatically if we're
CONFIG_NOT_COHERENT_CACHE. In the future, this will also
be enabled for builds that need swiotlb. If PPC_NEED_DMA_SYNC_OPS
is not defined, the dma_sync_*_for_* ops compile to nothing.
Otherwise, they access the dma_ops pointers for the sync ops.
This patch also changes dma_sync_single_range_* to actually
sync the range - previously it was using a generous
dma_sync_single. dma_sync_single_* is now implemented
as a dma_sync_single_range with an offset of 0.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On my screen, when something crashes, I only have space for maybe 16
functions of the stack trace before the information above it scrolls
off the screen. It's easy to hack the kernel to print out only that
much, but it's harder to remember to do it. This introduces a config
option for it so that I can keep the setting in my config.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refactor the RCU based pte free code that was used on ppc64 to be used
on all powerpc.
Additionally refactor pte_free() & pte_free_kernel() into common code
between ppc32 & ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The tlb invalidates in kmap_atomic/kunmap_atomic can be called from
IRQ context, however they are only local invalidates (on the processor
that the kmap was called on). In the future we want to use IPIs to
do tlb invalidates this causes issue since flush_tlb_page() is considered
a broadcast invalidate.
Add local_flush_tlb_page() as a non-broadcast invalidate and use it in
kmap_atomic() since we don't have enough information in the
flush_tlb_page() call to determine its local.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the ifdefs so we only use hash_page_sync if we have
CONFIG_SMP && CONFIG_PPC_STD_MMU_32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit hash code didn't need it so far so we don't update
mm->cpu_vm_mask on context switch. This however will break when we
merge the RCU based page table freeing patch and other upcoming 32-bit
embedded SMP work, so this adds the update.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
