opregion-based platforms will send ACPI video event 0x80 for a range of
notification types for legacy compatibility. This is interpreted as a
display switch event, which may not be appropriate in the circumstances.
When we receive such an event we should make sure that the platform is
genuinely requesting a display switch before passing that event through
to userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Do not use this bit to indicate that load detection has completed,
instead just wait for vblank, at which point the load registers will
have been updated.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Yi Sun <yi.sun@intel.com>
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit a51f7a66fb.
We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: Keith Packard <keithp@keithp.com>
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
Upon review, all path share the same dependencies for updating the
registers and so we can benefit from sharing the code and checking
early.
This removes the unsightly intel_wait_for_vblank() from the lowlevel
functions and upon further analysis the only path that will require a
wait is if we are performing an instantaneous transition between two
valid FBC configurations. The page-flip path itself will have disabled
FBC registers and will have waited for at least one vblank before
finishing the flip and attempting to re-enable FBC. This wait can be
accomplished simply by delaying the enable until after we are sure that
a vblank will have passed, which we are already doing to make sure that
the display is settled before enabling FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
In order to accommodate the requirements of re-enabling FBC after
page-flipping, but to avoid doing so and incurring the cost of a wait
for vblank in the middle of a page-flip sequence, we defer the actual
enablement by 50ms. If any request to disable FBC arrive within that
interval, the enablement is cancelled and we are saved from blocking on
the wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Page-flipping updates the scanout address, nukes the FBC compressed
image and so forces an FBC update so that the displayed image remains
consistent. However, page-flipping does not update the FBC registers
themselves, which remain pointing to both the old address and the old
CPU fence. Future updates to the new front-buffer (scanout) are then
undetected!
This first approach to demonstrate the issue and highlight the fix,
simply disables FBC upon page-flip (a recompression will be forced on
every flip so FBC becomes immaterial) and then re-enables FBC in the
page-flip finish work function, so that the FBC registers are now
pointing to the new framebuffer and front-buffer rendering works once
more.
Ideally, we want to only re-enable FBC after page-flipping is complete,
as otherwise we are just wasting cycles and power (with needless
recompression) whilst the page-flipping application is still running.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33487
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Persistent mode is intended for use with front-buffer rendering, such as
X, where it is necessary to detect writes to the scanout either by the
GPU or through the CPU's fence, and recompress the dirty regions on the
fly. (By comparison to the back-buffer rendering, the scanout is always
recompressed after a page-flip.)
References: https://bugs.freedesktop.org/show_bug.cgi?id=33487
References: https://bugs.freedesktop.org/show_bug.cgi?id=31742
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
...and this requirement is enforced by intel_update_fbc() so we can
remove the later check from g4x_enable_fbc() and ironlake_enable_fbc().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The cfb_pitch was only used for 8xx_enable_fbc(), every later routine
was just overwriting the value with itself thanks to a copy'n'paste
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
...to ensure that any pending FBC enable tasklet is cancelled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
According to the hardware documentation, GDRST is exactly the same as on
Sandybridge. So simply enable the existing code.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec). Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
If ->detect is called too soon after a hot plug event, the sink may not
be ready yet. So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
When a hotplug event is received, we need to check the receiver cap bits
in case they've changed (as they might with a hub or chain config).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Makes it easier to search for DP related constants.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Especially after a hotplug or power status change, the sink may not
reply immediately to a link status query. So retry 3 times per the spec
to really make sure nothing is there.
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Now that we track bpp on a per-pipe basis, we can use the actual value
rather than assuming 24bpp.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This will catch bad fb configs earlier.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
To properly drive a framebuffer with a new depth or bpp, dither settings
and link bandwidth calculations may change, so make sure we go through a
full mode set in that case.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The Intel HDMI encoder can support 8bpc or 12bpc. Set the appropriate
value based on the pipe bpp when configuring the output.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
The pipe may be driving various bpp values depending on the display
configuration, so take that into account when calculating link bandwidth
requirements.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Updating the planes is device specific, so create a new display callback
and use it in pipe_set_base. (In fact we could go even further, valid
display plane bits have changed with each generation, as has tiled
buffer handling.)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
Figuring out which pipe bpp to use is a bit painful. It depends on both
the encoder and display configuration attached to a pipe. For instance,
to drive a 24bpp framebuffer out to an 18bpp panel, we need to use 6bpc
on the pipe but also enable dithering. But driving that same
framebuffer to a DisplayPort output on another pipe means using 8bpc and
no dithering.
So split out and enhance the code to handle the various cases, returning
an appropriate pipe bpp as well as whether dithering should be enabled.
Save the resulting pipe bpp in the intel_crtc struct for use by encoders
in calculating bandwidth requirements (defaults to 24bpp on pre-ILK).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This may not be the default value, so pull the bpc out of the pipe reg
and write it to the DP transcoder so proper dithering and signaling
occurs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This prevents us from setting reserved or incorrect bits on CougarPoint.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
These bits are reserved on ILK+ (ILK+ provides this feature in the
transcoder and pipe configuration instead, which we already set).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
Revert "drm/nvc0: recognise 0xdX chipsets as NV_C0"
drm/radeon/kms: fix typo in cayman reg offset
drm/radeon/kms: use correct reg on fusion when reading back mem config
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: apply HWSTAM writes to Ivy Bridge as well
drm/i915: move IRQ function table init to i915_irq.c
drm/i915/overlay: Fix unpinning along init error paths
drm/i915: Don't call describe_obj on NULL pointers
drm/i915: Hold struct_mutex during i915_save_state/i915_restore_state
In an attempt to fix 38862 and 38863.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This lets us make the various IRQ functions static and helps avoid
problems like the one fixed in "drm/i915: Use chipset-specific irq
installers" where one of the exported functions was called rather than
the chipset specific version.
This also fixes a UMS-mode bug -- the correct irq functions for IRL
and later chips were only getting loaded in the KMS path.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
As pointed out by Dan Carpenter, it was seemingly possible to hit an error
whilst mapping the buffer for the regs (except the only likely error
returns should not happen during init) and so leak a pin count on the
bo. To handle this we would need to reacquire the struct mutex, so for
simplicity rearrange for the lock to be held for the entire function.
For extra pedagogy, test that we only call init once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The vbios rom is >64k on a lot of modern asics. Increase
the fetch size for atrm to make sure we don't miss part
of a larger rom.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They use the same register interfaces, so we can simply enable the
existing code on IVB.
v2:
- resolve conflict with ring freq scaling, we can enable it too
v3:
- resolve conflict again, this time on drm-intel-next
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
