'echo 1 > log_event' generates the bogus "MAC is in deep sleep"
or "Timeout waiting for hardware access" log messages when
the interface is down, we should just disallow accessing the
device through debugfs when it is down.
Signed-off-by: Richard A. Griffiths <richardx.a.griffiths@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to check trans for non-null
here as it has already been checked in the
caller. This fixes an smatch warning that we
check after having dereferenced it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Debug messages should be printed using dev_dbg() not
dev_err() which requires DEBUG to be defined.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some messages were missing a trailing newline, add it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
When authentication/association timed out, the driver would
complain bitterly, printing the message
ACTIVATE a non DRIVER active station id ... addr ...
The cause turns out to be that when the AP station is added
but we don't associate, the IWL_STA_UCODE_INPROGRESS is set
but never cleared. This then causes iwl_restore_stations()
to attempt to resend it because it uses the flag internally
and uploads even if it didn't set it itself.
To fix this issue and not upload the station again when it
has already been removed by mac80211, clear the flag after
adding it in case we add it only for association.
Cc: stable@vger.kernel.org
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I saw that when the watchdog triggers, the packets do go
through if we wait enough time. So we still have an issue
where packets are blocked in the Tx queue for a short while
and this needs to be debugged separately. For now, don't
restart the driver when it is not needed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dwell time for scanning is currently limited
so that it fits into the timings inside the ucode
when that is tracking DTIM/beacon periods for the
AP(s) it's connected to.
However, when it's connected to two APs, those
may be in lockstep, for example if they both have
a DTIM interval of 100 TU, then one could be 50
TU after the other, leaving only 50 TU free to
be used by scanning.
Since we can't know how far apart they are the
only option is to restrict to 1/2 of the minium
of the two APs.
In theory, it would be possible to not use 1/2 of
the minimum but take into account that if they
have different intervals then there will be a bit
more time since they can't be in lockstep, but as
they will have 100 TU intervals in practice that
complex calculation will probably just result in
hard-to-find bugs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__get_str() is identical to (char *)__get_dynamic_array()
that is in the code now, substitute __get_str to make the
code more readable.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's one message that goes just over the
limit of 100 characters, so bump the limit to
110 to get rid of the warning from that.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the op_mode defines the queue mapping, let it do it
completely through the API functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently when mac80211 asks to change the interface
type, we will accept it for both the BSS and PAN
contexts. This is not terribly complicated today,
but with the addition of the P2P Device abstraction
the PAN context handling will get more complex, so
restrict mac_change_interface to the BSS context.
Also fix a small locking issue and use is_active
instead of the vif pointer to check if the other
context is activated, guarding exclusive interface
types on the BSS context (IBSS) against the PAN
context being used for something else.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the first interface is active, then scanning
on it or the second interface can take a little
longer than 7s (I observed around 8s.) Bump the
timeout to 15s to avoid aborting a scan that is
still running, just taking more time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My previous commit to shorten the radio reset time
caused issues as the firmware checks the active
dwell time against the quiet time, asserting that
the dwell is >= quiet time. This isn't really
needed in case of passive scanning like here, but
of course we need to pass that check.
To fix this, override the quiet time to be the
same as the radio reset dwell time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When debugging is disabled, the event log functions aren't
functional in the way that the debugfs file expects. This
leads to the debugfs access crashing. Since the event log
functions aren't functional then, remove the debugfs file
when CONFIG_IWLWIFI_DEBUG is not set.
Cc: stable@kernel.org
Reported-by: Lekensteyn <lekensteyn@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the eeprom parsing code overrides the sku
field directly with 11n_disable parameters, there's
no longer a need to keep a copy of this field.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The effect of using a short single-channel scan
to reset the radio is that scanning a channel
that isn't in use needs to re-tune the radio.
This means that the dwell time is irrelevant,
so use a shorter time.
While at it, clean up the code for this a bit.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 26a7ca9a71 ("iwlwifi: refactor EEPROM reading/parsing")
broke the 11n_disable module parameter's BIT(0) to disable all HT
operation (using the other bits to disable aggregation only was
unaffected). Restore this by overriding the SKU when parsing the
EEPROM if the module parameter is set.
Reported-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the device is doing an internal radio reset
scan, ROC can be rejected to the supplicant with
busy status which confuses it.
One option would be to queue the ROC and handle
it later, but since the radio reset scan is very
quick we can just wait for it to finish instead.
Also add a warning since we shouldn't run into
the case of having a scan active when requesting
a ROC in any other case since mac80211 will not
scan while ROC or ROC while scanning.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature needs to be disabled for all NICs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable was accessed without taking the lock.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really not needed, we already have a lock inside
the accesses to the prph.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is not needed since notif_wait_lock is never accessed
from IRQ.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is required by the op_mode API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few op_mode of the op_mode API functions have requirements
on the running context of the caller. Document that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We introduced a lock here in ff1ffb850b ("iwlwifi: fix dynamic
loading"). But we missed an error path which needs an unlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This flow can actually happen due to a corner case in
mac80211: the station is deleted before we get a chance
to reclaim all the packets in flight in AGG queue.
The tid_data for this station is zeroed, and we lose
the match with the Tx queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since request_module_nowait() can't be backported
use request_module() instead -- we don't need the
asynchronous behaviour of request_module_nowait()
here since we're running in the firmware request
work struct.
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to commit 26a7ca9a71 ("iwlwifi: refactor EEPROM
reading/parsing") adding a new parameter, while commit
d2c8b15d0c ("iwlwifi: use correct supported firmware
for 6035 and 6000g2") added a new device structure we
need to add the parameter to the new device structure
to make 6035 device work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For AGG queues, we must match between the WiFi sequence
number and the TFD number. This is a HW (SCD) requirement.
This is a take two of my
iwlwifi: add debug in Tx path in AGG flow
This will allow us to catch bad cases in which the packets aren't in
the right place on the ring.
which disappeared during code move.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In fragmentation we don't update the write pointer of the
HW immediately. So we shouldn't modify the timer in that
case.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CMD_SYNC is zero so the if (cmd->flags & CMD_SYNC) is never true and we
never check the assertion.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the queue gets stuck from time to time, we are trying
to get as much information as we can when this occurs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver is built into the kernel instead of a module
when the system boots it results in a panic. The order things are built in
results in their initialization order when built into the kernel. Wifi
has to be initialized before mvm or dvm.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Brandon Misemer <brandon.misemer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the driver_data area in ieee80211_tx_info which
resides in the CB overrides the info->control field.
Add a comment to prevent mistakes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This locking isn't needed. The only locking we need is when
we access prph registers but there is already a separate
lock for that.
Since we haven't returned from the mac80211's
IEEE80211_AMPDU_TX_OPERATIONAL ampdu_action, we cannot
receive any Tx frame for that sta / tid while enabling the
queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is not needed, we just need to tell the SCD not to use
that queue. We will reconfigure that queue when we will use
it again.
Clean up a bit the code on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Print some more info from the SCD's SRAM and dump the TRB
from the FH.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
