Initialize the .cmd member by using a designated struct
initializer. This fixes warning of missing field initializers,
and makes code a little easier to read.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been reports of oversize UDP packets being sent to the
driver to be transmitted, causing error conditions. The issue is
likely caused by the dst of the SKB switching between 'lo' with
64K MTU and the hardware device with a smaller MTU. Patches are
being proposed by Mahesh Bandewar <maheshb@google.com> to fix the
issue.
In the meantime, add a quick length check in the driver to prevent
the error. The driver uses the TX packet size as index to look up an
array to setup the TX BD. The array is large enough to support all MTU
sizes supported by the driver. The oversize TX packet causes the
driver to index beyond the array and put garbage values into the
TX BD. Add a simple check to prevent this.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: linux-block@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The timer function, zstd_reclaim_timer_fn(), reschedules itself under
certain conditions. When cleaning up, take the lock and remove all
workspaces. This prevents the timer from rearming itself. Lastly, switch
to del_timer_sync() to ensure that the timer function can't trigger as
we're unloading.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently, running sample "task_fd_query" and "tracex3" occurs the
following error. On kernel v5.0-rc* this sample will be unavailable
due to the removal of function 'blk_start_request' at commit "a1ce35f".
(function removed, as "Single Queue IO scheduler" no longer exists)
$ sudo ./task_fd_query
failed to create kprobe 'blk_start_request' error 'No such file or
directory'
This commit will change the function 'blk_start_request' to
'blk_mq_start_request' to fix the broken sample.
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Alexei Starovoitov says:
====================
Introduce per program stats to monitor the usage BPF.
v2->v3:
- rename to run_time_ns/run_cnt everywhere
v1->v2:
- fixed u64 stats on 32-bit archs. Thanks Eric
- use more verbose run_time_ns in json output as suggested by Andrii
- refactored prog_alloc and clarified behavior of stats in subprogs
====================
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Return bpf program run_time_ns and run_cnt via bpf_prog_info
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
JITed BPF programs are indistinguishable from kernel functions, but unlike
kernel code BPF code can be changed often.
Typical approach of "perf record" + "perf report" profiling and tuning of
kernel code works just as well for BPF programs, but kernel code doesn't
need to be monitored whereas BPF programs do.
Users load and run large amount of BPF programs.
These BPF stats allow tools monitor the usage of BPF on the server.
The monitoring tools will turn sysctl kernel.bpf_stats_enabled
on and off for few seconds to sample average cost of the programs.
Aggregated data over hours and days will provide an insight into cost of BPF
and alarms can trigger in case given program suddenly gets more expensive.
The cost of two sched_clock() per program invocation adds ~20 nsec.
Fast BPF progs (like selftests/bpf/progs/test_pkt_access.c) will slow down
from ~10 nsec to ~30 nsec.
static_key minimizes the cost of the stats collection.
There is no measurable difference before/after this patch
with kernel.bpf_stats_enabled=0
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
CL2600/CL2800 servers leveraged Proliant hardware but are targeted to a
different market segment and come with a different firmware base. Based
upon targeted market needs, the servers de-featured certain aspects of iLO.
As a result, hpilo driver still claims the hardware but is not functional,
so we decided to blacklist it with SSID 0x0289 to reduce confusion to
customers.
Signed-off-by: Matt Hsiao <matt.hsiao@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having explicit if statements excluding devices,
use a pci_device_id table of devices to blacklist.
HPE will put out minor updates to the iLO using the same device
info except for the subsystem device id. hpilo driver takes the
approach to claim based upon {Vendor, Device, SubVendor} and it
allows old software to work on new hardware without patching.
As our primary way to support our customers is via distros, the
patching process could take months to go upstream and then
backported to multiple releases of multiple distros.
This approach worked fairly well as this is only the second time
in 10+ years that we need to blacklist an instance.
Signed-off-by: Matt Hsiao <matt.hsiao@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/virt/vboxguest/vboxguest_core.c: In function ‘vbg_core_ioctl’:
drivers/virt/vboxguest/vboxguest_core.c:1486:10: warning: this statement may fall through [-Wimplicit-fallthrough=]
f32bit = true;
~~~~~~~^~~~~~
drivers/virt/vboxguest/vboxguest_core.c:1489:2: note: here
case VBG_IOCTL_HGCM_CALL(0):
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/misc/mic/scif/scif_rma.c: In function ‘scif_unregister_window’:
drivers/misc/mic/scif/scif_rma.c:665:12: warning: this statement may fall through [-Wimplicit-fallthrough=]
send_msg = true;
~~~~~~~~~^~~~~~
drivers/misc/mic/scif/scif_rma.c:668:2: note: here
case OP_IN_PROGRESS:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the below sparse warnings by either making the functions
static or by adding a declaration in the relevant header file.
In addition, the patch removes goya_mmap completely as it doesn't add any
additional benefit.
Fixes the following sparse warnings:
drivers/misc/habanalabs/habanalabs_drv.c:24:1: warning: symbol 'hl_devs_idr' was not declared. Should it be static?
drivers/misc/habanalabs/habanalabs_drv.c:25:1: warning: symbol 'hl_devs_idr_lock' was not declared. Should it be static?
drivers/misc/habanalabs/memory.c:1451:5: warning: symbol 'hl_vm_ctx_init_with_ranges' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:396:5: warning: symbol 'goya_send_pci_access_msg' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:417:5: warning: symbol 'goya_pci_bars_map' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:557:6: warning: symbol 'goya_reset_link_through_bridge' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:774:5: warning: symbol 'goya_early_fini' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:857:6: warning: symbol 'goya_late_fini' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:971:5: warning: symbol 'goya_sw_fini' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:1233:5: warning: symbol 'goya_init_cpu_queues' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:2914:5: warning: symbol 'goya_suspend' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:2939:5: warning: symbol 'goya_resume' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:2952:5: warning: symbol 'goya_mmap' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:2957:5: warning: symbol 'goya_cb_mmap' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:2973:6: warning: symbol 'goya_ring_doorbell' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3063:6: warning: symbol 'goya_flush_pq_write' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3068:6: warning: symbol 'goya_dma_alloc_coherent' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3074:6: warning: symbol 'goya_dma_free_coherent' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3080:6: warning: symbol 'goya_get_int_queue_base' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3138:5: warning: symbol 'goya_send_job_on_qman0' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3295:5: warning: symbol 'goya_test_queue' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3417:6: warning: symbol 'goya_dma_pool_zalloc' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3426:6: warning: symbol 'goya_dma_pool_free' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3432:6: warning: symbol 'goya_cpu_accessible_dma_pool_alloc' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3448:6: warning: symbol 'goya_cpu_accessible_dma_pool_free' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3458:5: warning: symbol 'goya_dma_map_sg' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3467:6: warning: symbol 'goya_dma_unmap_sg' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:3473:5: warning: symbol 'goya_get_dma_desc_list_size' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4210:5: warning: symbol 'goya_parse_cb_no_mmu' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4261:5: warning: symbol 'goya_parse_cb_no_ext_quque' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4294:5: warning: symbol 'goya_cs_parser' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4307:6: warning: symbol 'goya_add_end_of_cb_packets' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4334:5: warning: symbol 'goya_context_switch' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4426:6: warning: symbol 'goya_restore_phase_topology' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4460:5: warning: symbol 'goya_debugfs_read32' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4510:5: warning: symbol 'goya_debugfs_write32' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4738:6: warning: symbol 'goya_handle_eqe' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:4836:6: warning: symbol 'goya_get_events_stat' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:5075:5: warning: symbol 'goya_send_heartbeat' was not declared. Should it be static?
drivers/misc/habanalabs/goya/goya.c:5253:5: warning: symbol 'goya_get_eeprom_data' was not declared. Should it be static?
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch increase the size field in the uapi structure of the Memory
IOCTL from 32-bit to 64-bit. This is to allow the user to allocate and/or
map memory in chunks that are larger then 4GB.
Goya's device memory (DRAM) can be up to 16GB, and for certain
topologies, the user may want an allocation that is larger than 4GB.
This change doesn't break current user-space because there was a "pad"
field in the uapi structure right after the size field. Changing the size
field to be 64-bit and removing the pad field maintains compatibility with
current user-space.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the code in charge of looking up the USB PHY when no platdata
is provided. Attempt to get a generic USB PHY first, then look for a
legacy USB PHY through device-tree and finally get any registered PHY
with the correct type.
This way, only a single USB PHY is obtained and the flow is easier to
understand and follow.
All error pointers (except for EPROBE_DEFER) are considered as PHY
not found.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.
This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.
Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.
When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX USB controller may drive the usb power line directly, but the
polarity depends on the board. Reset state of the polarity is low-active so
add this property to allow it to be high-active.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those 2 headers files are not required now.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the check to improve readibility
CHECK: Alignment should match open parenthesis
Signed-off-by: Madhumitha Prabakaran <madhumithabiw@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
T6 adapters generates DDP completion message on receiving all iSCSI pdus in
a sequence. Because of this, driver can not keep track of tcp sequence
number for T6 adapters.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
EROFS has an optimized path called TAIL merging, which is designed
to merge multiple reads and the corresponding decompressions into
one if these requests read continuous pages almost at the same time.
In general, it behaves as follows:
________________________________________________________________
... | TAIL . HEAD | PAGE | PAGE | TAIL . HEAD | ...
_____|_combined page A_|________|________|_combined page B_|____
1 ] -> [ 2 ] -> [ 3
If the above three reads are requested in the order 1-2-3, it will
generate a large work chain rather than 3 individual work chains
to reduce scheduling overhead and boost up sequential read.
However, if Read 2 is processed slightly earlier than Read 1,
currently it still generates 2 individual work chains (chain 1, 2)
but it does in-place decompression for combined page A, moreover,
if chain 2 decompresses ahead of chain 1, it will be a race and
lead to corrupted decompressed page. This patch fixes it.
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering a read request with two decompressed file pages,
If a decompression work cannot be started on the previous page
due to memory pressure but in-memory LTP map lookup is done,
builder->work should be still NULL.
Moreover, if the current page also belongs to the same map,
it won't try to start the decompression work again and then
run into trouble.
This patch aims to solve the above issue only with little changes
as much as possible in order to make the fix backport easier.
kernel message is:
<4>[1051408.015930s]SLUB: Unable to allocate memory on node -1, gfp=0x2408040(GFP_NOFS|__GFP_ZERO)
<4>[1051408.015930s] cache: erofs_compress, object size: 144, buffer size: 144, default order: 0, min order: 0
<4>[1051408.015930s] node 0: slabs: 98, objs: 2744, free: 0
* Cannot allocate the decompression work
<3>[1051408.015960s]erofs: z_erofs_vle_normalaccess_readpages, readahead error at page 1008 of nid 5391488
* Note that the previous page was failed to read
<0>[1051408.015960s]Internal error: Accessing user space memory outside uaccess.h routines: 96000005 [#1] PREEMPT SMP
...
<4>[1051408.015991s]Hardware name: kirin710 (DT)
...
<4>[1051408.016021s]PC is at z_erofs_vle_work_add_page+0xa0/0x17c
<4>[1051408.016021s]LR is at z_erofs_do_read_page+0x12c/0xcf0
...
<4>[1051408.018096s][<ffffff80c6fb0fd4>] z_erofs_vle_work_add_page+0xa0/0x17c
<4>[1051408.018096s][<ffffff80c6fb3814>] z_erofs_vle_normalaccess_readpages+0x1a0/0x37c
<4>[1051408.018096s][<ffffff80c6d670b8>] read_pages+0x70/0x190
<4>[1051408.018127s][<ffffff80c6d6736c>] __do_page_cache_readahead+0x194/0x1a8
<4>[1051408.018127s][<ffffff80c6d59318>] filemap_fault+0x398/0x684
<4>[1051408.018127s][<ffffff80c6d8a9e0>] __do_fault+0x8c/0x138
<4>[1051408.018127s][<ffffff80c6d8f90c>] handle_pte_fault+0x730/0xb7c
<4>[1051408.018127s][<ffffff80c6d8fe04>] __handle_mm_fault+0xac/0xf4
<4>[1051408.018157s][<ffffff80c6d8fec8>] handle_mm_fault+0x7c/0x118
<4>[1051408.018157s][<ffffff80c8c52998>] do_page_fault+0x354/0x474
<4>[1051408.018157s][<ffffff80c8c52af8>] do_translation_fault+0x40/0x48
<4>[1051408.018157s][<ffffff80c6c002f4>] do_mem_abort+0x80/0x100
<4>[1051408.018310s]---[ end trace 9f4009a3283bd78b ]---
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves the following page use-after-free issue,
z_erofs_vle_unzip:
...
for (i = 0; i < nr_pages; ++i) {
...
z_erofs_onlinepage_endio(page); (1)
}
for (i = 0; i < clusterpages; ++i) {
page = compressed_pages[i];
if (page->mapping == mngda) (2)
continue;
/* recycle all individual staging pages */
(void)z_erofs_gather_if_stagingpage(page_pool, page); (3)
WRITE_ONCE(compressed_pages[i], NULL);
}
...
After (1) is executed, page is freed and could be then reused, if
compressed_pages is scanned after that, it could fall info (2) or
(3) by mistake and that could finally be in a mess.
This patch aims to solve the above issue only with little changes
as much as possible in order to make the fix backport easier.
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Cc: <stable@vger.kernel.org> # 4.19+
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using viid to get pf number, directly get pf number from
lldi->pf.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We had a test-report where, under memory pressure, adding LUNs to the
systems would fail (the tests add LUNs strictly in sequence):
[ 5525.853432] scsi 0:0:1:1088045124: Direct-Access IBM 2107900 .148 PQ: 0 ANSI: 5
[ 5525.853826] scsi 0:0:1:1088045124: alua: supports implicit TPGS
[ 5525.853830] scsi 0:0:1:1088045124: alua: device naa.6005076303ffd32700000000000044da port group 0 rel port 43
[ 5525.853931] sd 0:0:1:1088045124: Attached scsi generic sg10 type 0
[ 5525.854075] sd 0:0:1:1088045124: [sdk] Disabling DIF Type 1 protection
[ 5525.855495] sd 0:0:1:1088045124: [sdk] 2097152 512-byte logical blocks: (1.07 GB/1.00 GiB)
[ 5525.855606] sd 0:0:1:1088045124: [sdk] Write Protect is off
[ 5525.855609] sd 0:0:1:1088045124: [sdk] Mode Sense: ed 00 00 08
[ 5525.855795] sd 0:0:1:1088045124: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5525.857838] sdk: sdk1
[ 5525.859468] sd 0:0:1:1088045124: [sdk] Attached SCSI disk
[ 5525.865073] sd 0:0:1:1088045124: alua: transition timeout set to 60 seconds
[ 5525.865078] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015070] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.015213] sd 0:0:1:1088045124: alua: port group 00 state A preferred supports tolusnA
[ 5526.587439] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
[ 5526.588562] scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured
Looking at the code of scsi_alloc_sdev(), and all the calling contexts,
there seems to be no reason to use GFP_ATMOIC here. All the different
call-contexts use a mutex at some point, and nothing in between that
requires no sleeping, as far as I could see. Additionally, the code that
later allocates the block queue for the device (scsi_mq_alloc_queue())
already uses GFP_KERNEL.
There are similar allocations in two other functions:
scsi_probe_and_add_lun(), and scsi_add_lun(),; that can also be done with
GFP_KERNEL.
Here is the contexts for the three functions so far:
scsi_alloc_sdev()
scsi_probe_and_add_lun()
scsi_sequential_lun_scan()
__scsi_scan_target()
scsi_scan_target()
mutex_lock()
scsi_scan_channel()
scsi_scan_host_selected()
mutex_lock()
scsi_report_lun_scan()
__scsi_scan_target()
...
__scsi_add_device()
mutex_lock()
__scsi_scan_target()
...
scsi_report_lun_scan()
...
scsi_get_host_dev()
mutex_lock()
scsi_probe_and_add_lun()
...
scsi_add_lun()
scsi_probe_and_add_lun()
...
So replace all these, and give them a bit of a better chance to succeed,
with more chances of reclaim.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings by adding the proper missing breaks:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function _base_display_OEMs_branding :
drivers/scsi/mpt3sas/mpt3sas_base.c:3548:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3566:3: note: here
case MPI2_MFGPAGE_DEVID_SAS2308_2:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3567:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3601:3: note: here
case MPI25_MFGPAGE_DEVID_SAS3008:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3735:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3745:3: note: here
case MPI2_MFGPAGE_DEVID_SAS2308_2:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3746:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3768:3: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing break statement and fix identation issue.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 9cb62fa24e ("aacraid: Log firmware AIF messages")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No users left, kill it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use request tag instead of the serial number when printing out logging
messages.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the request tag for logging instead of the scsi command serial number.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drop references to scsi_cmnd->serial_number.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Negative constant left-shift is undefined behaviour in the C standard, and
as such newer versions of clang (at least) warn against it. GCC supports it
for a long time, but it would be better to remove it and rely on defined
behaviour.
My understanding is "~(-1 << N)" in 2's complement is intended to generate
a bit pattern of zeroes ending with N '1' bits. The same can be achieved by
"(1 << N) - 1" in a well-defined way, so switch to it to remove the
warning.
Tested: building a kernel with generic SCSI tape, and checking basic
operations (mt status, mt eject) on a real LTO unit. Cannot test the osst
driver.
Signed-off-by: Iustin Pop <iustin@k1024.org>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: a4080225f5 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add this functionality, placing the descriptor being read in the actual
data buffer in the bio.
That is, for both read and write descriptors query upiu, we are using the
job's request_payload. This in turn, is mapped back in user land to the
applicable sg_io_v4 xferp: dout_xferp for write descriptor, and din_xferp
for read descriptor.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow to read descriptors via raw upiu. This in fact was forbidden just as
a precaution, as ufs-bsg actually enforces which functionality is
supported.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we had a write descriptor query upiu, we appended the descriptor right
after the bsg request. This was fine as the bsg driver allows to allocate
whatever buffer we needed in its job request.
Still, the proper way to deliver payload, however small (we only write
config descriptors of 144 bytes), is by using the job request payload data
buffer.
So change this ABI now, while ufs-bsg is still new, and nobody is actually
using it.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFSHC driver defines a few quirks that are not used anywhere:
UFS_DEVICE_QUIRK_BROKEN_LCC
UFS_DEVICE_NO_VCCQ
UFS_DEVICE_QUIRK_NO_LINK_OFF
UFS_DEVICE_NO_FASTAUTO
Let's remove them.
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 60f0187031.
There was one conflict in drivers/scsi/ufs/ufshcd.c
<<<<<<< HEAD
/* Init check for device descriptor sizes */
ufshcd_init_desc_sizes(hba);
ret = ufs_get_device_desc(hba, &card);
if (ret) {
dev_err(hba->dev, "%s: Failed getting device info. err = %d\n",
__func__, ret);
goto out;
}
ufs_fixup_device_setup(hba, &card);
ufshcd_tune_unipro_params(hba);
ret = ufshcd_set_vccq_rail_unused(hba,
(hba->dev_quirks & UFS_DEVICE_NO_VCCQ) ? true : false);
if (ret)
goto out;
=======
ufs_advertise_fixup_device(hba);
>>>>>>> parent of 60f0187031c0... scsi: ufs: disable vccq if it's not needed by UFS device
Resolution: keep HEAD, and delete the ufshcd_set_vccq_rail_unused() call
and corresponding error-handling code.
Clean up loose ends in a follow-up patch.
60f0187031 introduced a small power optimization: ignore the vccq load
specified in the UFSHC DT node when said host controller is connected to
specific Flash chips (currently, Samsung and Hynix).
Unfortunately, this optimization breaks UFS on systems where vccq powers
not only the Flash chip, but the host controller as well, such as APQ8098
MEDIABOX or MTP8998:
[ 3.929877] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[ 5.433815] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[ 6.937771] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr: opcode 0x04 for idn 13 failed, index 0, err = -11
[ 6.937866] ufshcd-qcom 1da4000.ufshc: ufshcd_query_attr_retry: query attribute, idn 13, failed with error -11 after 3 retires
[ 6.946412] ufshcd-qcom 1da4000.ufshc: ufshcd_disable_auto_bkops: failed to enable exception event -11
[ 6.957972] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1587 failed 3 retries
[ 6.967181] ufshcd-qcom 1da4000.ufshc: dme-peer-get: attr-id 0x1586 failed 3 retries
[ 6.975025] ufshcd-qcom 1da4000.ufshc: ufshcd_get_max_pwr_mode: invalid max pwm tx gear read = 0
[ 6.982755] ufshcd-qcom 1da4000.ufshc: ufshcd_probe_hba: Failed getting max supported power mode
[ 8.505770] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[ 10.009807] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[ 11.513766] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag: Sending flag query for idn 3 failed, err = -11
[ 11.513861] ufshcd-qcom 1da4000.ufshc: ufshcd_query_flag_retry: query attribute, opcode 5, idn 3, failed with error -11 after 3 retires
[ 13.049807] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[ 14.553768] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[ 16.057767] ufshcd-qcom 1da4000.ufshc: __ufshcd_query_descriptor: opcode 0x01 for idn 8 failed, index 0, err = -11
[ 16.057872] ufshcd-qcom 1da4000.ufshc: ufshcd_read_desc_param: Failed reading descriptor. desc_id 8, desc_index 0, param_offset 0, ret -11
[ 16.067109] ufshcd-qcom 1da4000.ufshc: ufshcd_init_icc_levels: Failed reading power descriptor.len = 98 ret = -11
[ 37.073787] ufshcd-qcom 1da4000.ufshc: link startup failed 1
In my opinion, the rationale for the original patch is questionable. If
neither the UFSHC, nor the Flash chip, require any load from vccq, then
that power rail should simply not be specified at all in the DT.
Working around that fact in the driver is detrimental, as evidenced by the
failure to initialize the host controller on MSM8998.
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_device_quiesce() and scsi_device_resume() are called during
system-wide suspend and resume. scsi_device_quiesce() only succeeds for
SCSI devices that are in one of the RUNNING, OFFLINE or TRANSPORT_OFFLINE
states (see also scsi_set_device_state()). This patch avoids that the
following warning is triggered when resuming a system for which quiescing a
SCSI device failed:
WARNING: CPU: 2 PID: 11303 at drivers/scsi/scsi_lib.c:2600 scsi_device_resume+0x4f/0x58
CPU: 2 PID: 11303 Comm: kworker/u8:70 Not tainted 5.0.0-rc1+ #50
Hardware name: LENOVO 80E3/Lancer 5B2, BIOS A2CN45WW(V2.13) 08/04/2016
Workqueue: events_unbound async_run_entry_fn
Call Trace:
scsi_dev_type_resume+0x2e/0x60
async_run_entry_fn+0x32/0xd8
process_one_work+0x1f4/0x420
worker_thread+0x28/0x3c0
kthread+0x118/0x130
ret_from_fork+0x22/0x40
Cc: Przemek Socha <soprwa@gmail.com>
Reported-by: Przemek Socha <soprwa@gmail.com>
Fixes: 3a0a529971 ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If you run "make" in a pristine source tree, currently Kbuild will
start to build Kconfig to let it show the error message.
It would be more straightforward to check it in Makefile and let
it fail immediately.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
