Si-En Technology is a fabless design house which offers
audio amplifiers, LED drivers and sensors.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The IS31FL32xx family of LED controllers are I2C devices with multiple
constant-current channels, each with independent 256-level PWM control.
Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml
This has been tested on the IS31FL3236 and IS31FL3216, on an ARM
(TI am335x) platform.
The programming paradigm of these devices is similar in the following
ways:
- All registers are 8 bit
- All LED control registers are write-only
- Each LED channel has a PWM register (0-255)
- PWM register writes are shadowed until an Update register is poked
- All have a concept of Software Shutdown, which disables output
However, there are some differences in devices:
- 3236/3235 have a separate Control register for each LED,
(3218/3216 pack the enable bits into fewer registers)
- 3236/3235 have a per-channel current divisor setting
- 3236/3235 have a Global Control register that can turn off all LEDs
- 3216 is unique in a number of ways
- OUT9-OUT16 can be configured as GPIOs instead of LED controls
- LEDs can be programmed with an 8-frame animation, with
programmable delay between frames
- LEDs can be modulated by an input audio signal
- Max output current can be adjusted from 1/4 to 2x globally
- Has a Configuration register instead of a Shutdown register
This driver currently only supports the base PWM control function
of these devices. The following features of these devices are not
implemented, although it should be possible to add them in the future:
- All devices are capable of going into a lower-power "software
shutdown" mode.
- The is31fl3236 and is31fl3235 can reduce the max output current
per-channel with a divisor of 1, 2, 3, or 4.
- The is31fl3216 can use some LED channels as GPIOs instead.
- The is31fl3216 can animate LEDs in hardware.
- The is31fl3216 can modulate LEDs according to an audio input.
- The is31fl3216 can reduce/increase max output current globally.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds a binding description for the is31fl3236/35/18/16 I2C LED
controllers.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
ISSI is the stock ticker Integrated Silicon Solutions Inc.
Company website: http://www.issi.com
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
To be compatible with this change, remove an unnecessary label by
replacing it with direct return statement.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use the GPIO flag definition instead of a numeric literal, so the casual
reader grepping for GPIOF_ will find the GPIO flags used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Add helpers for calling brightness_set(_blocking) allowing to
simplify the code and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
In case of error, the function gpio_to_desc() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Improve the wording for the comment about the led status, and while at
it also use the standard formatting for multi-line comments.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When a USB LED device is unplugged the remove call chain calls
led_classdev_unregister which tries to switch the LED off.
As the device has been removed already this results in a ENODEV
error message in dmesg.
Avoid this error message by ignoring ENODEV in calls from
led_classdev_unregister if the LED device is flagged as pluggable.
Therefore a new flag LED_HW_PLUGGABLE was introduced which should be set by
all LED drivers handling pluggable LED devices (mainly USB LED devices).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now that workqueues have been removed from individual drivers and
were replaced with a core-internal workqueue we shouldn't
encourage people to add new workqueues to drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Pull turbostat updates for 4.6 from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
tools/power turbostat: Decode MSR_MISC_PWR_MGMT
tools/power turbostat: decode HWP registers
x86 msr-index: Simplify syntax for HWP fields
tools/power turbostat: CPUID(0x16) leaf shows base, max, and bus frequency
tools/power turbostat: decode more CPUID fields
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.5:
- Fix JZ4780 build with DEBUG_ZBOOT and MACH_JZ4780
- Fix build with DEBUG_ZBOOT and MACH_JZ4780
- Fix issue with uninitialised temp_foreign_map
- Fix awk regex compile failure with certain versions of awk. At
this time, the sole user, ld-ifversion, is only used on MIPS"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: smp.c: Fix uninitialised temp_foreign_map
MIPS: Fix build error when SMP is used without GIC
ld-version: Fix awk regex compile failure
MIPS: Fix build with DEBUG_ZBOOT and MACH_JZ4780
When calculate_cpu_foreign_map() recalculates the cpu_foreign_map
cpumask it uses the local variable temp_foreign_map without initialising
it to zero. Since the calculation only ever sets bits in this cpumask
any existing bits at that memory location will remain set and find their
way into cpu_foreign_map too. This could potentially lead to cache
operations suboptimally doing smp calls to multiple VPEs in the same
core, even though the VPEs share primary caches.
Therefore initialise temp_foreign_map using cpumask_clear() before use.
Fixes: cccf34e941 ("MIPS: c-r4k: Fix cache flushing for MT cores")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS_GIC_IPI should only be selected when MIPS_GIC is also
selected, otherwise it results in a compile error. smp-gic.c uses some
functions from include/linux/irqchip/mips-gic.h like
plat_ipi_call_int_xlate() which are only added to the header file when
MIPS_GIC is set. The Lantiq SoC does not use the GIC, but supports SMP.
The calls top the functions from smp-gic.c are already protected by
some #ifdefs
The first part of this was introduced in commit 72e20142b2 ("MIPS:
Move GIC IPI functions out of smp-cmp.c")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12774/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ld-version.sh script fails on some versions of awk with the
following error, resulting in build failures for MIPS:
awk: scripts/ld-version.sh: line 4: regular expression compile failed (missing '(')
This is due to the regular expression ".*)", meant to strip off the
beginning of the ld version string up to the close bracket, however
brackets have a meaning in regular expressions, so lets escape it so
that awk doesn't expect a corresponding open bracket.
Fixes: ccbef1674a ("Kbuild, lto: add ld-version and ld-ifversion ...")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Michal Marek <mmarek@suse.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/12838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ingenic SoC declares ZBOOT support, but debug definitions are missing
for MACH_JZ4780 resulting in a build failure when DEBUG_ZBOOT is set.
The UART addresses are same as with JZ4740, so fix by covering JZ4780
with those as well.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12830/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MSR_CONFIG_TDP_NOMINAL:
should print all 8 bits of base_ratio (bit 0:7) 0xFF
MSR_CONFIG_TDP_LEVEL_1:
should print all 15 bits of PKG_MIN_PWR_LVL1 (bit 48:62) 0x7FFF
should print all 15 bits of PKG_MAX_PWR_LVL1 (bit 32:46) 0x7FFF
should print all 8 bits of LVL1_RATIO (bit 16:23) 0xFF
should print all 15 bits of PKG_TDP_LVL1 (bit 0:14) 0x7FFF
And the same modification to MSR_CONFIG_TDP_LEVEL_2.
MSR_TURBO_ACTIVATION_RATIO:
should print all 8 bits of MAX_NON_TURBO_RATIO (bit 0:7) 0xFF
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=0: unlimited)
should print as
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=8: unlimited)
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat already checks whether calling each cpuid leavf is legal,
and it doesn't look at the function return value,
so call the simpler gcc intrinsic __cpuid() instead of __get_cpuid().
syntax only, no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
The accuracy of Bzy_Mhz and Busy% depend on reading
the TSC, APERF, and MPERF close together in time.
When there is a very short measurement interval,
or a large system is profoundly idle, the changes
in APERF and MPERF may be very small.
They can be small enough that an expensive interrupt
between reading APERF and MPERF can cause the APERF/MPERF
ratio to become inaccurate, resulting in invalid
calculation and display of Bzy_MHz.
A dummy APERF read of APERF makes this problem
much more rare. Apparently this 1st systemn call
after exiting a long stretch of idle is when we
typically see expensive timer interrupts that cause
large jitter.
For the cases that dummy APERF read fails to prevent,
we compare the latency of the APERF and MPERF reads.
If they differ by more than 2x, we re-issue them.
Signed-off-by: Len Brown <len.brown@intel.com>
The column "GFX%c6" show the percentage of time the GPU
is in the "render C6" state, rc6. Deep package C-states on several
systems depend on the GPU being in RC6.
This information comes from the counter
/sys/class/drm/card0/power/rc6_residency_ms,
as read before and after the measurement interval.
Signed-off-by: Len Brown <len.brown@intel.com>
Under the column "GFXMHz", show a snapshot of this attribute:
/sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz
This is an instantaneous snapshot of what sysfs presents
at the end of the measurement interval. turbostat does
not average or otherwise perform any math on this value.
Signed-off-by: Len Brown <len.brown@intel.com>
The new IRQ column shows how many interrupts have occurred on each CPU
during the measurement inteval. This information comes from
the difference between /proc/interrupts shapshots made before
and after the measurement interval.
The first row, the system summary, shows the sum of the IRQS
for all CPUs during that interval.
Signed-off-by: Len Brown <len.brown@intel.com>
skip the open(2)/close(2) on each msr read
by keeping the /dev/cpu/*/msr files open.
The remaining read(2) is generally far fewer cycles
than the removed open(2) system call.
Signed-off-by: Len Brown <len.brown@intel.com>
By default...
Turbostat --debug gconfiguration info goes to stderr.
In FORK mode, turbostat statistics go to stderr.
In PERIODIC mode, turbostat statistics go to stdout.
These defaults do not change, but an option "--out file"
will send all output above only to the specified file.
Signed-off-by: Len Brown <len.brown@intel.com>
some tools processing turbostat output
have difficulty with items that begin with %...
Reported-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Following changes have been made:
- changed MSR_NHM_TURBO_RATIO_LIMIT to MSR_TURBO_RATIO_LIMIT in debug print
for consistency with Developer Manual
- updated definition of bitfields in MSR_TURBO_RATIO_LIMIT and appropriate
parsing code
- added x200 to list of architectures that do not support Nahlem compatible
definition of MSR_TURBO_RATIO_LIMIT register (x200 has the register but
bits definition is custom)
- fixed typo in code that parses MSR_TURBO_RATIO_LIMIT
(logical instead of bitwise operator)
- changed MSR_TURBO_RATIO_LIMIT parsing algorithm so the print out had the
same order as implementations for other platforms
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
x200 does not enable any way to programmatically obtain bus clock
speed. Bclk for the architecture has a fixed value of 100 MHz.
At the same time x200 cannot be included in has_snb_msrs since
it does not support C7 idle state.
prior to this patch, MHz values reported on this chip
were erroneously calculated using bclk of 133MHz,
causing MHz values to be reported 33% higher than actual.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat -i interval_sec
will sample and display statistics every interval_sec.
interval_sec used to be a whole number of seconds,
but now we accept a decimal, as small as 0.001 sec (1 ms).
Signed-off-by: Len Brown <len.brown@intel.com>
Pull block merge fix from Jens Axboe.
This fixes the block segment counting bug and resulting sg overrun
reported by Kent Overstreet, introduced with the last block pull.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't optimize for non-cloned bio in bio_get_last_bvec()
Pull x86 fixes from Ingo Molnar:
"This fixes 3 FPU handling related bugs, an EFI boot crash and a
runtime warning.
The EFI fix arrived late but I didn't want to delay it to after v4.5
because the effects are pretty bad for the systems that are affected
by it"
[ Actually, I don't think the EFI fix really matters yet, because we
haven't switched to the separate EFI page tables in mainline yet ]
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Fix boot crash by always mapping boot service regions into new EFI page tables
x86/fpu: Fix eager-FPU handling on legacy FPU machines
x86/delay: Avoid preemptible context checks in delay_mwaitx()
x86/fpu: Revert ("x86/fpu: Disable AVX when eagerfpu is off")
x86/fpu: Fix 'no387' regression
Pull SCSI target bug fix from Nicholas Bellinger:
"Here is an outstanding target-core bug-fix for v4.5 code."
This patch addresses a recent Task Management (TMR) regression related
to larger set of multi-port LUN_RESET bug-fixes in v4.5-rc5.
It drops a left-over target_put_sess_cmd() of se_cmd->cmd_kref within
ABORT_TASK failure path, once a se_cmd descriptor has already
completed posting response to fabric driver logic, and must be skipped
during normal ABORT_TASK se_cmd->tag lookup"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect ABORT_TASK put for completed commands
For !BIO_CLONED bio, we can use .bi_vcnt safely, but it
doesn't mean we can just simply return .bi_io_vec[.bi_vcnt - 1]
because the start postion may have been moved in the middle of
the bvec, such as splitting in the middle of bvec.
Fixes: 7bcd79ac50d9(block: bio: introduce helpers to get the 1st and last bvec)
Cc: stable@vger.kernel.org
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A few new AVX-512 instruction groups/features are added in cpufeatures.h
for enuermation: AVX512DQ, AVX512BW, and AVX512VL.
Clear the flags in fpu__xstate_clear_all_cpu_caps().
The specification for latest AVX-512 including the features can be found at:
https://software.intel.com/sites/default/files/managed/07/b7/319433-023.pdf
Note, I didn't enable the flags in KVM. Hopefully the KVM guys can pick up
the flags and enable them in KVM.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Link: http://lkml.kernel.org/r/1457667498-37357-1-git-send-email-fenghua.yu@intel.com
[ Added more detailed feature descriptions. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some machines have EFI regions in page zero (physical address
0x00000000) and historically that region has been added to the e820
map via trim_bios_range(), and ultimately mapped into the kernel page
tables. It was not mapped via efi_map_regions() as one would expect.
Alexis reports that with the new separate EFI page tables some boot
services regions, such as page zero, are not mapped. This triggers an
oops during the SetVirtualAddressMap() runtime call.
For the EFI boot services quirk on x86 we need to memblock_reserve()
boot services regions until after SetVirtualAddressMap(). Doing that
while respecting the ownership of regions that may have already been
reserved by the kernel was the motivation behind this commit:
7d68dc3f10 ("x86, efi: Do not reserve boot services regions within reserved areas")
That patch was merged at a time when the EFI runtime virtual mappings
were inserted into the kernel page tables as described above, and the
trick of setting ->numpages (and hence the region size) to zero to
track regions that should not be freed in efi_free_boot_services()
meant that we never mapped those regions in efi_map_regions(). Instead
we were relying solely on the existing kernel mappings.
Now that we have separate page tables we need to make sure the EFI
boot services regions are mapped correctly, even if someone else has
already called memblock_reserve(). Instead of stashing a tag in
->numpages, set the EFI_MEMORY_RUNTIME bit of ->attribute. Since it
generally makes no sense to mark a boot services region as required at
runtime, it's pretty much guaranteed the firmware will not have
already set this bit.
For the record, the specific circumstances under which Alexis
triggered this bug was that an EFI runtime driver on his machine was
responding to the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event during
SetVirtualAddressMap().
The event handler for this driver looks like this,
sub rsp,0x28
lea rdx,[rip+0x2445] # 0xaa948720
mov ecx,0x4
call func_aa9447c0 ; call to ConvertPointer(4, & 0xaa948720)
mov r11,QWORD PTR [rip+0x2434] # 0xaa948720
xor eax,eax
mov BYTE PTR [r11+0x1],0x1
add rsp,0x28
ret
Which is pretty typical code for an EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE
handler. The "mov r11, QWORD PTR [rip+0x2424]" was the faulting
instruction because ConvertPointer() was being called to convert the
address 0x0000000000000000, which when converted is left unchanged and
remains 0x0000000000000000.
The output of the oops trace gave the impression of a standard NULL
pointer dereference bug, but because we're accessing physical
addresses during ConvertPointer(), it wasn't. EFI boot services code
is stored at that address on Alexis' machine.
Reported-by: Alexis Murzeau <amurzeau@gmail.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raphael Hertzog <hertzog@debian.org>
Cc: Roger Shimizu <rogershimizu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1457695163-29632-2-git-send-email-matt@codeblueprint.co.uk
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=815125
Signed-off-by: Ingo Molnar <mingo@kernel.org>
