Specify chip revision at attach time rather than a firmware image.
This is a better way to ensure that the correct firmware is loaded
for the correct revision of the chip.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
convert the firmware configuration attach-time parameter from
a pointer to an integer so as to remove the static dependency
created by the previous changesets.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
newer versions of the xc5000 silicon require newer firmware
while remaining 100% driver compatible. original versions
of the xc5000a continue to use the same firmware.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for some -Wuninitialized compiler warnings.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase mt2063 frequency_max to tune to channel 69(858Mhz).
Jose Alberto
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes are needed, in order to make az6007 compile with the
upstream tree. Most of the changes are due to the upstream drxk
module.
Even allowing its compilation, the driver is not working yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In xc4000 chipsets real signal and noise level is stored in register
0x0A and 0x0B,so we can use those registers to monitor signal strength.
I tested this patch on 2 different cards Leadtek DVR3200 and DTV2000H
Plus, both with same results, I used special antenna hubs (toner 4x, 6x,
8x and 12x) with mesured signal lost, both registers are in dB value,
first represent signal with limit value -113.5dB (should be -114dB) and
exactly match with test results. Second represents noise level also in
dB and there is no maximum value, but from tests we can drop everything
above 32dB which tuner realy can't use, signal was usable till 20dB
noise level.
In digital mode we can take signal strength but sadly noise level is not
relevant and real value is stored in demodulator for now just zl10353,
also digital mode is just for testing, because it needs changing other
parts of code which reads data only from demodulator.
In analog mode I was able to test only FM radio, signal level is not
important, it says something about cable and hub losts, but nothing
about real quality of reception, so even if we have signal level at
minimum 113dB we can still here radio, because of that it is displaied
only in debug mode, but for real signal level is used noise register
which is again very accurate, radio noise level was betwen 6-20dB for
good signal, 20-25dB for medium signal, and above 25dB signal is
unusable.
For now real benefit of this patch is only for FM radio mode.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVB-T did not work at all - only 6 MHz was working but it is not
commonly used.
Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces the previous one proposed in the thread "xc3028:
force reload of DTV7 firmware in VHF band with Zarlink demodulator",
at the linux-media@vger.kernel.org ML.
The problem is that the firmware DTV78 works fine in UHF band (8 MHz
bandwidth) but is not working at all in VHF band (7 MHz bandwidth).
Reading the comments inside the code, I figured out that the real
problem could be connected to the formula used to calculate the center
frequency offset in VHF band.
In fact, removing this adjustment fixes the problem:
if ((priv->cur_fw.type & DTV78) && freq < 470000000)
offset -= 500000;
This is coherent to what was implemented for the DTV7 firmware by an
Australian user:
if (priv->cur_fw.type & DTV7)
offset += 500000;
In the end, now the center frequency is the same for all firmwares
(DTV7, DTV8, DTV78) and doesn't depend on channel bandwidth.
The final code looks clean and simple, and there is no need for any
"magic" adjustment:
if (priv->cur_fw.type & DTV6)
offset = 1750000;
else /* DTV7 or DTV8 or DTV78 */
offset = 2750000;
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ops->info.type is handled inside the dvb_frontend
core, only for DVBv3 calls, and according with the
delivery system. So, drivers should not care or use it,
otherwise, it may have issues with DVBv5 calls.
The drivers that were still using it were detected via
this small temporary hack:
--- a/include/linux/dvb/frontend.h
+++ b/include/linux/dvb/frontend.h
@@ -29,13 +29,16 @@
#include <linux/types.h>
typedef enum fe_type {
+#if defined(__DVB_CORE__) || !defined (__KERNEL__)
FE_QPSK,
FE_QAM,
FE_OFDM,
FE_ATSC
+#else
+FE_FOOO
+#endif
} fe_type_t;
-
typedef enum fe_caps {
FE_IS_STUPID = 0,
FE_CAN_INVERSION_AUTO = 0x1,
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The per-delivery system tables are confusing.
Add an extra table that explains them, and some
dprintk calls, that allows to check if mt2063 driver
is working as expected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of printing it just for debug purposes, outputs the detected
version at the logs. This may be useful if someone wants to report
a problem.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, improve a few debug messages that helped to track the
issue and may be useful in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This also helps to identify when a device is not initialized,
if the bridge doesn't return an error for a I2C failed transfer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of crash, return -ENODEV, if the device is not poperly
initialized.
Also, give a second chance for it to initialize, at set_params
calls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mt2063.c:1531:12: warning: variable 'ofout' set but not used [-Wunused-but-set-variable]
mt2063.c:1531:6: warning: variable 'ofin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several vars at set_parms functions were set, but unused.
Remove them and change the logic to return -EINVAL if the
analog set_param is used for digital mode.
At the analog side, cleans the logic that sets the several
analog standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No functional changes on this patch. Better organize the delivery
system information and data types, putting everything together,
to improve readability.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver were using a hacky way of setting analog and digital
frequencies. Remove the hack and properly add the tuner logic for
each supported type of standard.
I was tempted to add more standards there, like SECAM and to fix
radio (as stepping seems broken), but I opted to keep it as-is,
as tests would be needed to add additional standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Such code is disabled via ifdef's. Also, they're ugly and rely
on some static structures. Just remove. If ever needed, the git
log can be used to recover it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial: now that all tuners use the DVBv5
way to pass parameters (e. g. via fe->dtv_property_cache), the
extra parameter can be removed from set_params() call.
After this change, very few DVBv3 specific stuff are left at the
tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The calc_regs() callback is used by a few frontends (mt352, nxt200x,
digitv and zl10353). On all places it is called, the parameters are
set by DVBv5 way. So, just use the DVBv5 struct and remove the
extra parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Despite its name, tuner-simple has a complex logic to set freqs ;)
Basically, it can be called by two different ways: via set_params()
or via calc_regs() callbacks. Both are bound to the DVBv3 API.
Also, set_params internally calls calc_regs().
In order to get rid of DVBv3 params at set_params(), it shouldn't
call calc_regs() anymore. The code duplication is very small,
as most of the code there is just to check for invalid parameters.
With regards to calc_regs(), it should still trust on bandwidth and
frequency parameters passed via DVBv3, until a later patch fixes
it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This standard is not properly documented, but its settings are at
the tda18271dd driver, and are somewhat obvious, as they follow
the same logic as DVB-T 7MHz.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a bug on mxl5005s logic: when the bandwidth changes, but using
the same delivery system, the code discard the set_params()
reconfiguration request.
This was happening because, in the previous coding, the bandwidth
calculus were after the check for delivery system changes.
The previous patch changed the logic to estimate the bandwidth to
happend together with the changes at the delivery system.
So, with a one-statement change, it is possible to make the tuner to
reconfigure, in order to adjust to bandwidth changes. this will
likely fix issues on countries that use 7MHz/8MHz DVB-T channels.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver implements a fake get_bandwidth() callback. In
reallity, the tuner driver won't adjust its low-pass
filter based on a bandwidth, and were just providing a fake
method for demods to read whatever was "set".
This code is useless, as none of the drivers that use
this tuner seems to require a get_bandwidth() callback.
While here, convert set_params to use the DVBv5 way to pass
parameters to tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver implements a fake get_bandwidth() callback. In
reallity, the tuner driver won't adjust its low-pass
filter based on a bandwidth, and were just providing a fake
method for demods to read whatever was "set".
This code is useless, as none of the drivers that use
this tuner seems to require a get_bandwidth() callback.
While here, convert set_params to use the DVBv5 way to pass
parameters to tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver implements a fake get_bandwidth() callback. In
reallity, the tuner driver won't adjust its low-pass
filter based on a bandwidth, and were just providing a fake
method for demods to read whatever was "set".
This code is useless, as none of the drivers that use
this tuner seems to require a get_bandwidth() callback.
While here, convert set_params to use the DVBv5 way to pass
parameters to tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SYS_DVBC_ANNEX_AC is an alias for SYS_DVBC_ANNEX_A. However,
the first one is incorrect, as not all devices support both.
So, replace its occurrences by the proper value (either
SYS_DVBC_ANNEX_A or both SYS_DVBC_ANNEX_A and SYS_DVBC_ANNEX_C).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linux 3.2-rc7
* tag 'v3.2-rc7': (1304 commits)
Linux 3.2-rc7
netfilter: xt_connbytes: handle negation correctly
Btrfs: call d_instantiate after all ops are setup
Btrfs: fix worker lock misuse in find_worker
net: relax rcvbuf limits
rps: fix insufficient bounds checking in store_rps_dev_flow_table_cnt()
net: introduce DST_NOPEER dst flag
mqprio: Avoid panic if no options are provided
bridge: provide a mtu() method for fake_dst_ops
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
sparc64: Fix MSIQ HV call ordering in pci_sun4v_msiq_build_irq().
pata_of_platform: Add missing CONFIG_OF_IRQ dependency.
ipv4: using prefetch requires including prefetch.h
VFS: Fix race between CPU hotplug and lglocks
vfs: __read_cache_page should use gfp argument rather than GFP_KERNEL
USB: Fix usb/isp1760 build on sparc
net: Add a flow_cache_flush_deferred function
...
Conflicts:
drivers/media/common/tuners/tda18218.c
drivers/media/video/omap3isp/ispccdc.c
drivers/staging/media/as102/as102_drv.h
Instead of using a roll-off factor, change DRX-K & friends to select
the bandwidth filter and the Nyquist half roll-off via delivery system.
This provides a cleaner support for Annex A/C switch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While xc5000 supports 7MHz bandwidth, the driver were lacking the code
implementing this feature, causing tuning issues with VHF chanels
used in Countries like Italy.
After this patch:
>>> tune to: 177500000:INVERSION_AUTO:BANDWIDTH_7_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
0x0000 0x0d49: pmt_pid 0x0102 RAI -- Rai 1 (running)
0x0000 0x0d4a: pmt_pid 0x0101 RAI -- Rai 2 (running)
0x0000 0x0d4b: pmt_pid 0x0100 RAI -- Rai 3 TGR Veneto (running)
0x0000 0x0d53: pmt_pid 0x0118 RAI -- Rai News (running)
0x0000 0x0d54: pmt_pid 0x0119 Rai -- Rai 3 TGR Emilia Romagna (running)
0x0000 0x0d4c: pmt_pid 0x0103 Rai -- Rai Radio1 (running)
0x0000 0x0d4d: pmt_pid 0x0104 Rai -- Rai Radio2 (running)
0x0000 0x0d4e: pmt_pid 0x0105 Rai -- Rai Radio3 (running)
Network Name 'Rai'
Tested-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Devin Heitmueller <dheitmueller@kernellabs.com>:
> It seems like a change such as this could significantly change the
> timing of tuner initialization if you have multiple xc5000 based
> products that might have a slow i2c bus. Was that intentional?
After discussed with Eddi de Pierri <eddi@depieri.net>, it was pointed that
the change was not intentional, and it was just a trial while developing
the patches that add support for HVR-930C.
So, remove this hack.
Reported-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked by: Eddi de Pierri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register to read should be written to register 0xfb and then
perform I2C read to get reg value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chip configures IF frequency resolution of 50 kHz. Round it nearest.
Off-by 50 kHz is almost nothing in real life...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Default IF for 6 MHz bandwidth is 3 MHz. Use that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.2-rc2': (3068 commits)
Linux 3.2-rc2
hfs: add sanity check for file name length
fsl-rio: fix compile error
blackfin: Fixup export.h includes
Blackfin: add serial TX IRQ in individual platform resource
virtio-pci: fix use after free
ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
drm/radeon/kms/combios: fix dynamic allocation of PM clock modes
[CPUFREQ] db8500: fix build error due to undeclared i variable
bma023: Add SFI translation for this device
vrtc: change its year offset from 1960 to 1972
ce4100: fix a build error
arm/imx: fix imx6q mmc error when mounting rootfs
arm/imx: fix AUTO_ZRELADDR selection
arm/imx: fix the references to ARCH_MX3
ARM: mx51/53: set pwm clock parent to ipg_perclk
btrfs: rename the option to nospace_cache
drm/radeon/kms/pm: switch to dynamically allocating clock mode array
drm/radeon/kms: optimize r600_pm_profile_init
drm/radeon/kms/pm: add a proper pm profile init function for fusion
...
Conflicts:
drivers/media/radio/Kconfig
With this patch I try again to add initial support for HVR930C.
Tested only DVB-T, since in Italy Analog service is stopped.
Actually "scan -a0 -f1", find only about 50 channel while 400 should
be available.
[mchehab@redhat.com: Tested with DVB-C and fixed a few whitespace issues]
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Annex C support were broken with the previous implementation,
as, at xc5000 and tda18271c2dd, it were choosing the wrong bandwidth
for some symbol rates.
At DRX-J, it were always selecting Annex A, even having Annex C
support coded there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write AUX byte to FM1216ME_MK3 when FM mode, better sensitivity. It can be
usefull for other tuners.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in clocksource
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These two macros were in module.h but now module.h is no longer
sprayed across every source file imaginable, so the users need
to expicitly call out their use of them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removed the unused Xtal_Int variable. That made it also possible to remove a
related function. However, the code of that function has been preserved in a
comment describing an equation. Without that function that comment would
have been hard to understand.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Standardize the mechanisms to emit logging messages.
A few other modules used an #include from saa7146,
convert those at the same time.
Add pr_fmt.
Convert printks to pr_<level>
Convert printks without KERN_<level> to appropriate pr_<level>.
Convert logging macros requiring multiple parentheses to normal style.
Removed embedded prefixes when pr_fmt was added.
Whitespace cleanups when around other conversions.
Use printf extension %pM to print mac address.
Coalesce format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Hunold <michael@mihu.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DVB framework will try to power-down an adapter that no-one is using
any more, but this assumes that the adapter is still connected to the
machine. That's not always true for a USB adapter, so disable the sleep
operations when the adapter has been physically unplugged.
This prevents I2C write failures with error -19 from appearing
occasionally in the dmesg log.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of these flags has been deprecated for nearly 4 years by:
commit f77bf01425
Author: Sam Ravnborg <sam@neptun.(none)>
Date: Mon Oct 15 22:25:06 2007 +0200
kbuild: introduce ccflags-y, asflags-y and ldflags-y
Moreover, these flags (at least EXTRA_CFLAGS) have been documented for command
line use. By default, gmake(1) do not override command line setting, so this is
likely to result in build failure or unexpected behavior.
Replace their usage by Kbuild's `{as,cc,ld}flags-y'.
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In radio mode, no frequency offset should be used.
Instead of taking Thierry's patch that creates a separate function
to calculate the digital offset, it seemed better to just keep
everything at the same place.
Reported-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When loading the firmware, complete each chunk by sending an I2C flush
command to the frontend. Some devices like the tm6000 seem to require
this to properly flush the I2C buffers.
The current code in tm6000 executes the flush command once after each
I2C transfer, which slows down the firmware loading especially when
loading large BASE type images.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the more current logging styles with pr_fmt.
Remove now unnecessary private include.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda827x is currently taking the demod IF frequency into account while
seeking for the proper tuner range. This is wrong, as the demod IF
frequency has nothing to do with the tuner PLL.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Solve the ./scripts/checkpatch.pl compliants for the patches
that added xc4000 support, including a few changes at dib0700.
While here, remove a few printk noise by converting some msgs
into debug ones.
Cc: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed the use of 'card_type' from the tuner configuration structure, and
replaced it with separate parameters to set board-specific configuration.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enabled code to check if the version of the firmware reported by the hardware
is correct after uploading it.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Various coding style changes:
- removed unused / commented out code
- changed C++ style comments to C format
- renamed functions and variables that included upper case letters in the name
- removed tabs from module parameter descriptions
- replaced the use of XC_RESULT_* with standard error codes
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added code to detect the XC4100 chip, which is presumably an analog-only
"value" version of the XC4000. It is not sure, however, if any devices
using this have actually been produced and sold, so the patch may be
unneeded.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch causes the tuner reset command to be ignored in the firmware
code, since this only happens when the BASE/INIT1 firmware is loaded by
check_firmware(), and in that case check_firmware() already calls the
reset callback before starting to load the firmware.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Minor coding changes related to the xc_tune_channel() function.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements support for analog TV and FM radio.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'audio_std' module parameter makes it possible to fine tune
some audio related aspects of the driver, like setting the exact
audio standard (NICAM, A2, etc.) to be used for some video standards.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch implements setting the registers in xc4000_set_params()
and xc4000_set_analog_params(). A new register is defined which enables
filtering of the composite video output (this is needed to avoid bad
picture quality with some boards).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch makes a few minor changes to the printing
of debug messages, and reporting the tuner status. The 'debug'
module parameter can now be set from 0 to 2 to control the
verbosity of debug messages.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes/cleans up the loading of the firmware file when the
driver is loaded and initialized.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements the xc4000_sleep() function.
The 'no_powerdown' module parameter is now interpreted differently:
- 0 uses a device-specific default
- 1 disables power management like before
- 2 enables power management
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for selecting a card type in struct
xc4000_config, to allow for implementing some card specific code
in the driver.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the following fixes in check_firmware():
- there is only one BASE and INIT1 firmware for XC4000
- loading SCODE is needed also for FM radio
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed unused code from load_scode() (all SCODE firmwares are
assumed to have the HAS_IF bit set).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firmware_name module parameter makes it possible to set the firmware
file name. It defaults to "xc4000.fw" if not specified.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc_get_frequency_error() function reported the frequency error
incorrectly. The data read from the hardware is a signed integer, in
15625 Hz units. The attached patch fixes the bug.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a mutex to xc4000_priv, to protect the driver
from being accessed by multiple processes at the same time.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements support for DVB-T with 7 MHz bandwidth.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the following changes to the standards table:
- added 'u16 int_freq' to struct XC_TV_STANDARD (needed for analog TV
and radio, 0 for DVB-T)
- added new standard for SECAM-D/K video with PAL-D/K audio
- the 'int_freq' values are now specified in the table
- changed VideoMode for NTSC and PAL-B/G standards
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the first of a set of patches that update the original xc4000
sources to my modified version. It removes some unused code, and makes
a few minor formatting changes.
[mchehab@redhat.com: re-add XC_TUNE_ANALOG/XC_TUNE_DIGITAL constants, to avoid compilation breakage]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some printk() calls added during driver development, and demote some
other messages to debug only (to reduce dmesg chatter).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Give the xc4000 firmware filename a filename that makes more sense for public
release.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't dump debug into to dmesg by default (something I had enabled during
bringup of the xc4000 driver).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack I had put in to force the firmware to be 8MHz, now setting
the firmware properly based on the target standard.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was confirmed by DibCom that i2c stretching is broken in the i2c master
on the dib7700. So we need to put a hack into the xc4000 driver to not
complain in certain very specific cases where we know i2c stretching occurs.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove hard-coded references to 5400, using the value passed in when the
xc4000 is attached.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly setup the standard firmware loading and scode loading, as well as
getting rid of a ton of dead code. Note that I am getting a single i2c
error when the standard firmware sets the video standard, but everything else
seems to be loading properly now.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to handle firmware blobs for the standard and scode. Note there
appears to be some issue with loading the DTV8 standard firmware, probably
related to direct/indirect mode.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we use the xc3028 version of the firmware file parsing routine (which
includes support for scodes and separate blobs), we can drop the xc5000
version of the code.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc4000 driver is based on the original xc5000 driver, and while the
xc5000 supports the XREG_BUSY register, the xc4000 does not. So remove the
code in question.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set the firmware type properly in order to locate the init1
firmware.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc3028 version does i2c splitting in a different manner than xc4000 and
xc5000, so reuse the xc5000 version of the routine (the key here being that
xc4000 expects the first *two* bytes to be the same for splitting transactions.
Doing it the xc3028 way was resulting in i2c errors partially through the
firmware load. With this change, it would appear that the entire base firmware
is being loaded successfully (product id now properly shows 0x0FA0).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch over to using the firmware management routines from the tuner-xc2028,
since that has support for scodes, etc.
This code still requires signficant cleanup, and at this point the base
firmware does not load properly (i2c write errors about 300 bytes in).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/mxl5005s.c: In function ‘mxl5005s_set_params’:
drivers/media/common/tuners/mxl5005s.c:4016: warning: enumeration value ‘BANDWIDTH_5_MHZ’ not handled in switch
drivers/media/common/tuners/mxl5005s.c:4016: warning: enumeration value ‘BANDWIDTH_10_MHZ’ not handled in switch
drivers/media/common/tuners/mxl5005s.c:4016: warning: enumeration value ‘BANDWIDTH_1_712_MHZ’ not handled in switch
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_setup_device() has saved the PCI revision in the pci_dev
struct since Linux 2.6.23. Use it.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.
On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
R_MPD bit 3 does not depend on analog vs. digital. Just use
(0x7f & pd) directly from the values in the main pll table.
Thanks to Stefan Sibiga for pointing this out.
Cc: Stefan Sibiga <stefansibiga@yahoo.ca>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix type of prog_cal and prog_tab variables to avoid any possible
calculation errors.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Misplaced parenthesis cause a calculation bug in
tda18271_rf_tracking_filters_init
Thanks to Stefan Sibiga for pointing this out.
Cc: Stefan Sibiga <stefansibiga@yahoo.ca>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/tuner-xc2028.c: In function 'generic_set_freq':
drivers/media/common/tuners/tuner-xc2028.c:936:15: warning: comparison between 'enum tuner_mode' and 'enum v4l2_tuner_type'
Argument type was enum tuner_mode, but should have been enum v4l2_tuner_type.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My Hauppauge WinTV HVR-1400 needs sometimes more then only one retry to load the firmware successfully.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In commit 567aba0b79, the probe address
for tda8290_probe and tda8295_probe was hard-coded to 0x4b, which is the
default i2c address for those devices, but its possible for the device
to be at an alternate address, 0x42, which is the case for the HVR-1950.
If we probe the wrong address, probe fails and we have a non-working
device. We have the actual address passed into the function by way of
i2c_props, we just need to use it. Also fix up some copy/paste comment
issues and streamline debug spew a touch. Verified to restore my
HVR-1950 to full working order.
Special thanks to Ken Bass for reporting the issue in the first place,
and to both he and Gary Buhrmaster for aiding in debugging and analysis
of the problem.
Reported-by: Ken Bass <kbass@kenbass.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (101 commits)
[media] staging/lirc: fix mem leaks and ptr err usage
[media] hdpvr: reduce latency of i2c read/write w/recycled buffer
[media] hdpvr: enable IR part
[media] rc/mceusb: timeout should be in ns, not us
[media] v4l2-device: fix 'use-after-freed' oops
[media] v4l2-dev: don't memset video_device.dev
[media] zoran: use video_device_alloc instead of kmalloc
[media] w9966: zero device state after a detach
[media] v4l: Fix a use-before-set in the control framework
[media] v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
[media] DocBook/v4l: update V4L2 revision and update copyright years
[media] DocBook/v4l: fix validation error in dev-rds.xml
[media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
[media] v4l2-ctrls: fix missing 'read-only' check
[media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
[media] ir-kbd-i2c: Add back defaults setting for Zilog Z8's at addr 0x71
[media] lirc_zilog: Update TODO.lirc_zilog
[media] lirc_zilog: Add Andy Walls to copyright notice and authors list
[media] lirc_zilog: Remove useless struct i2c_driver.command function
[media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
...
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are some weird bugs at tda8290/tda18271 initialization, as it
insits do do analog initialization during DVB frontend attach:
DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (Fujitsu mb86A20s)...
mb86a20s: mb86a20s_initfe
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271_init: [2-0060|M] error -5 on line 830
tda18271_tune: [2-0060|M] error -5 on line 908
tda18271_write_regs
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271c2_rf_tracking_filters_correction: [2-0060|M] error -5 on line 265
tda18271_write_regs
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x25, len = 1, i2c_transfer returned: -5
tda18271_channel_configuration: [2-0060|M] error -5 on line 119
tda18271_set_analog_params: [2-0060|M] error -5 on line 1045
tda18271_set_analog_params: [2-0060|M] error -5 on line 1045
tda829x 2-004b: tda8295 not locked, no signal?
tda829x 2-004b: tda8295_i2c_bridge: disable i2c gate
tda829x 2-004b: tda8295 not locked, no signal?
tda829x 2-004b: tda8295_i2c_bridge: disable i2c gate
mb86a20s_i2c_writereg: writereg error (rc == -5, reg == 0x29, data == 0x33)
mb86a20s: Init failed. Will try again later
The problem is that mb86a20s is only visible if the analog part is disabled.
However, due to a trick at mb86a20s, it will later initialize properly:
mb86a20s: mb86a20s_initfe: Initialization succeded.
This is hacky and ugly. However, I coldn't find any easy way to fix it.
A proper fix would be to have a resource locking schema, used by both
V4L and DVB parts that would block access to analog registers while
digital registers are in use, but this will probably put tda829x into
a dead lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Kworld SBTVD, tda8295-c1 starts in power off mode. It needs
to be powered, otherwise, the I2C gate control command won't work.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read operations should be preceeded by a write operation. However,
nothing prevents that an I2C operation could happen between the two
transactions.
To avoid that problem, use an unique I2C transfer for both parts of
the I2C transaction.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert saa7146 to use core-assisted locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/tda18218.c: In function 'tda18218_wr_regs':
drivers/media/common/tuners/tda18218.c:58:5: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
Drivers should append their name on exported symbols, to avoid
conflicts with allyesconfig:
drivers/staging/built-in.o: In function `format_by_fourcc':
/home/v4l/work_trees/linus/drivers/staging/cx25821/cx25821-video.c:96: multiple definition of `format_by_fourcc'
drivers/media/built-in.o:/home/v4l/work_trees/linus/drivers/media/common/saa7146_video.c:88: first defined here
Let's rename both occurences with a small shellscript:
for i in drivers/staging/cx25821/*.[ch]; do sed s,format_by_fourcc,cx25821_format_by_fourcc,g <$i >a && mv a $i; done
for i in drivers/media/common/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
for i in include/media/saa7146*.[ch]; do sed s,format_by_fourcc,saa7146_format_by_fourcc,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the new visible Kconfig keyword to avoid producing error for two menus
that are visible only if Tuner/frontend customise options are enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 1724c8fa7e added an option to change
the maximum I2C size to 8 bytes. However, it forgot to replace the previous
usage at af9015 to use the newly defined macro value
(TDA18271_16_BYTE_CHUNK_INIT).
A latter changeset (e350d44fed) extended the
possible values for .small_i2c field and, instead of using a random sequence
of numbers, it used a number that makes more sense (e. g. the actual limit,
in terms of bytes).
However, as af9015 were using .small_i2c = 1, this become undefined, and the
restriction of a max size of 16 was gone.
While here, fix the reported msg size at tda18271-common.c.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By default, tda18271 tries to optimize I2C bus by updating all registers
at the same time. Unfortunately, some devices doesn't support it.
The current logic has a problem when small_i2c is equal to 8, since there
are some transfers using 11 + 1 bytes.
Fix the problem by enforcing the max size at the right place, and allows
reducing it to max = 3 + 1.
Acked-by: Michael Krufky <mkrufky@kernellabs.com>
Acked-by: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of doing:
[ 82.581639] tda18271 4-0060: creating new instance
[ 82.588411] Unknown device detected @ 4-0060, device not supported.
[ 82.594695] tda18271_attach: [4-0060|M] error -22 on line 1272
[ 82.600530] tda18271 4-0060: destroying instance
Print:
[ 468.740392] Unknown device (0) detected @ 4-0060, device not supported.
for the error message, to help detecting what's going wrong with the
device.
This helps to detect when the driver is using the wrong I2C bus (or have
the i2g gate switch pointing to the wrong place), on devices like cx231xx
that just return 0 on reads to a non-existent i2c device.
Reviewed-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_waiton() must unlock and relock ext_lock if it has to wait.
For that to happen it needs the videobuf_queue pointer.
Don't attempt to unlock/relock q->ext_lock unless it was locked in the
first place.
vb->state has to be protected by a spinlock to be safe.
This patch is based on code from Mauro Carvalho Chehab <mchehab@redhat.com>.
[mchehab@redhat.com: add extra argument to a few missing places]
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an ext_lock argument to the videobuf init functions. This allows
drivers to pass the vdev->lock pointer (or any other externally held lock)
to videobuf. For now all drivers just pass NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack in the tuner code for the mxb board. This hack is no longer
needed since the tuner is now probed on its correct address as specified
by the mxb driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Making static data const avoids allocation of additional r/w memory and
reduces initialisation time. It also provides some additional opportunities
for compiler optimisations.
Signed-off-by: Lawrence Rust <lvr@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tuner, DVB frontend and video helper chip drivers are by default
autoselected by their respective host cards, this, however, doesn't make
much sense on SoC-based systems. Disable autoselection on EMBEDDED
systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
