Change vddci as well as vddc when changing power modes
on evergreen/ni. Also, properly set vddci on boot up
for ni cards. The vbios only sets the limited clocks
and voltages on boot until the mc ucode is loaded. This
should fix stability problems on some btc cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed for setting voltages other than vddc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We previously used a static array, but some new systems
had more states then we had array space, so dynamically
allocate space based on the number of states in the vbios.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33851
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The accelerate mode bit gets checked by certain atom
command tables to set up some register state. It needs
to be clear when setting modes and set when not.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=26942
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Seems some other boards do this as well.
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
NI chips no longer load the MC ucode in the asic_init sequence so
the asic comes up in a basic mode with low engine/memory clocks and
a voltage. Once the MC ucode is loaded by the driver the card
can be programmed to it's proper default clocks and voltage. As such
the default clocks in the firmware info table as the post clocks, not
the default running clocks. Track the default post clocks and default
running clocks separately to handle this.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acer laptop (TravelMate 5730G) has an HDMI connector
on the laptop and a DVI connector on the docking station
and both share the same encoder, hpd pin, and ddc line.
The bios connector table reflects this and is technically
correct, however, we drop the DVI connector here since
xrandr has no concept of encoders (only crtcs and connectors)
and will try and drive both connectors with different crtcs
which isn't possible on the hardware side and leaves no crtcs
for LVDS or VGA.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=32732
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (771 commits)
drm/i915: Undo "Uncouple render/power ctx before suspending"
drm/i915: Allow the application to choose the constant addressing mode
drm/i915: dynamic render p-state support for Sandy Bridge
drm/i915: Enable EI mode for RCx decision making on Sandybridge
drm/i915/sdvo: Border and stall select became test bits in gen5
drm/i915: Add Guess-o-matic for pageflip timestamping.
drm/i915: Add support for precise vblank timestamping (v2)
drm/i915: Add frame buffer compression on Sandybridge
drm/i915: Add self-refresh support on Sandybridge
drm/i915: Wait for vblank before unpinning old fb
Revert "drm/i915: Avoid using PIPE_CONTROL on Ironlake"
drm/i915: Pass clock limits down to PLL matcher
drm/i915: Poll for seqno completion if IRQ is disabled
drm/i915/ringbuffer: Make IRQ refcnting atomic
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915: Enable RC6 autodownclocking on Sandybridge
drm/i915: Terminate the FORCE WAKE after we have finished reading
drm/i915/gtt: Clear the cachelines upon resume
drm/i915: Restore GTT mapping first upon resume
...
This block may contain various additional LCD info such
as physical size and a stored EDID.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems have the LCD width and height in mm available in the
LCD info table. Use this info if there is no EDID to provide it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios power tables on my inagua board seem a bit funky...
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The function was getting too large. Rework it to share
more state better handle new power table formats.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
System specific spread spectrum overrides can be specified in
the integrated system info table for Fusion APUs. This adds
support for using those overrides.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
2b5b1d7da9583484b3a9e7e375a90ca0e8ca07c2
(drm/radeon/kms: add support for clock/data path routers)
That patch completed mux support for ddc and cd line routing
between connectors. This patch fixes an indexing typo that was
resulting in the atom bios router objects not always being walked,
ensures the validity entries for the reused router structure are
reset for every connector object walked, and corrects the masking
operations used to update the mux control bits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Tyson Whitehead <twhitehead@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a follow on to:
26b5bc9864
(drm/radeon/kms: add support for router objects)
That patch added support for systems that use a mux to control
the ddc line routing between the connectors. This patch adds
support for systems that use a mux to control the encoder
clock and data path routing to the connectors.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=31339
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make TV standard and DFP table revisions debug only.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch reworks spread spectrum handling to enable it
properly on lvds and DP/eDP links. It also fixes several
bugs in the old spread spectrum code.
- Use the ss recommended reference divider if available
when calculating the pll
- Use the proper ss command tables on pre-DCE3 asics
- Avoid reading past the end of the ss info tables
- Enable ss on evergreen asics (lvds, dp, tmds)
- Enable ss on DP/eDP links
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent changes to the old algo (prefer high post div)
coupled with the range and precision limitations of using
fixed point with the new algo make the new algo less
useful. So drop the new algo. This should work as well
or better than the old new/old combinations and simplifies
the code a lot.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30218
among others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Board has no digital connectors
Reported-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The 7th entry in a lot of evergreen i2c gpio tables is partially
zeroed. Fix the entry.
Should fix the missing ddc entry in:
https://bugs.freedesktop.org/show_bug.cgi?id=29255
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The meaning of ucMemoryType changed on recent boards, however,
ulBootUpSidePortClock should be set properly across all boards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
On most newer asics, digital encoders have two links each
and they can be used independantly. As such, treat them as
separate encoders otherwise the individual links will not
get programmed properly at modeset time.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always zero-init a structure on the stack which is returned by a
function. Otherwise you may leak random stack data from previous
function calls.
This fixes the following warning I was seeing:
CC [M] drivers/gpu/drm/radeon/radeon_atombios.o
drivers/gpu/drm/radeon/radeon_atombios.c: In function "radeon_atom_get_hpd_info_from_gpio":
drivers/gpu/drm/radeon/radeon_atombios.c:261: warning: "hpd.plugged_state" is used uninitialized in this function
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes lack of power saving with multiple heads on
some desktop cards.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16474
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
router objects are found on systems that use a mux to control
ddc line to connector routing or to control the actual clock and data
routing from the chip to the connectors. This patch implements ddc line
routing.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we added i2c buses as needed when enumerating connectors
power management, etc. This only exposed the actual buses used and
could have lead to the same buse getting created more than once if
one buses was used for more than one purpose. This patch sets up
all i2c buses on the card in one place and users of the buses just
point back to the one instance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connector is actually DVI rather than HDMI.
Reported-by: trapDoor <trapdoor6@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check ulBootUpMemoryClock on AMD IGPs.
Fix regression noticed by Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
track the current voltage level and avoid setting it
if the requested voltage is already set.
v2: check voltage type before checking current voltage
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vddc value in the power tables is not an actual voltage
like on discrete r6xx/r7xx/evergreen systems, but instead has
a symbolic meaning (e.g., NONE, LOW, HIGH, etc.). See atombios.h
Most RS780/RS880 vbioses don't have a SetVoltage table anyway,
so it shouldn't be doing anything to the hardware at the moment.
I need to figure out how voltage is supposed to work on the newer
IGPs; until then, disable it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The default power state does not always match the default clocks and voltage
for a particular card. The information in the firmware info table is correct
and should be used in preference to the info the default power state.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- This enables voltage adjustment on r6xx+ and certain
r5xx asics.
- Voltage drop support is already available for most
r1xx-r5xx asics.
V2: endian fix for voltage table.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/nouveau/nv40_graph.c: In function `nv40_graph_init':
drivers/gpu/drm/nouveau/nv40_graph.c:400: warning: the frame size of 1184 bytes is larger than 1024 bytes
drivers/gpu/drm/radeon/radeon_atombios.c: In function `radeon_get_atom_connector_info_from_supported_devices_table':
drivers/gpu/drm/radeon/radeon_atombios.c:857: warning: the frame size of 1872 bytes is larger than 1024 bytes
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
