The serial core may call the UART driver's start_tx() even if
tx is stopped; the UART driver must verify tx should be enabled
before transmitting.
Reported-by: Sam Ravnborg <sam@ravnborg.org>
cc: David S. Miller <davem@davemloft.net>
cc: <sparclinux@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
START_CHAR() & STOP_CHAR() can be disabled if set to '\0'
(__DISABLED_CHAR). UART drivers which define a send_xchar()
handler must not transmit __DISABLED_CHAR.
Document requirement.
Affected drivers:
sunsab
sunhv
cc: David S. Miller <davem@davemloft.net>
cc: <sparclinux@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sparc updates from David Miller:
1) Add sparc RAM output to /proc/iomem, from Bob Picco.
2) Allow seeks on /dev/mdesc, from Khalid Aziz.
3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.
4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
not insert it into the TLB miss hash tables otherwise we'll
livelock. Based upon work by Christopher Alexander Tobias Schulze.
5) Fix BREAK detection in sunsab driver when no actual characters are
pending, from Christopher Alexander Tobias Schulze.
6) Because we have modules --> openfirmware --> vmalloc ordering of
virtual memory, the lazy VMAP TLB flusher can cons up an invocation
of flush_tlb_kernel_range() that covers the openfirmware address
range. Unfortunately this will flush out the firmware's locked TLB
mapping which causes all kinds of trouble. Just split up the flush
request if this happens, but in the long term the lazy VMAP flusher
should probably be made a little bit smarter.
Based upon work by Christopher Alexander Tobias Schulze.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
sparc64: Fix up merge thinko.
sparc: Add "install" target
arch/sparc/math-emu/math_32.c: drop stray break operator
sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
sparc64: Guard against flushing openfirmware mappings.
sunsab: Fix detection of BREAK on sunsab serial console
bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
sparc64: Do not insert non-valid PTEs into the TSB hash table.
sparc64: avoid code duplication in io_64.h
sparc64: reorder functions in io_64.h
sparc64: drop unused SLOW_DOWN_IO definitions
sparc64: remove macro indirection in io_64.h
sparc64: update IO access functions in PeeCeeI
sparcspkr: use sbus_*() primitives for IO
sparc: Add support for seek and shorter read to /dev/mdesc
sparc: use %s for unaligned panic
drivers/sbus/char: Micro-optimization in display7seg.c
display7seg: Introduce the use of the managed version of kzalloc
sparc64 - add mem to iomem resource
Fix detection of BREAK on sunsab serial console: BREAK detection was only
performed when there were also serial characters received simultaneously.
To handle all BREAKs correctly, the check for BREAK and the corresponding
call to uart_handle_break() must also be done if count == 0, therefore
duplicate this code fragment and pull it out of the loop over the received
characters.
Patch applies to 3.16-rc6.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 717f3bbab3,
'serial_core: Fix conditional start_tx on ring buffer not empty'
exposes an incorrect assumption in several drivers' start_tx methods;
the tx ring buffer can, in fact, be empty when restarting tx while
performing flow control.
Affected drivers:
sunsab.c
ip22zilog.c
pmac_zilog.c
sunzilog.c
m32r_sio.c
imx.c
Other in-tree serial drivers either are not affected or already
test for empty tx ring buffer before transmitting.
Test for empty tx ring buffer in start_tx() method, after transmitting
x_char (if applicable).
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Seth Bollinger <sethb@digi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commits:
* 6732c8bb86 (TTY: switch
tty_schedule_flip)
* 2e124b4a39 (TTY: switch
tty_flip_buffer_push)
* 05c7cd3990 (TTY: switch
tty_insert_flip_string)
* 92a19f9cec (TTY: switch
tty_insert_flip_char)
* 227434f898 (TTY: switch
tty_buffer_request_room to tty_port)
introduced a potential NULL dereference to some drivers. In
particular, when the device is used as a console, incoming bytes can
kill the box. This is caused by removed checks for TTY against NULL.
It happened because it was unclear to me why the checks were there. I
assumed them superfluous because the interrupts were unbound or
otherwise stopped. But this is not the case for consoles for these
drivers, as was pointed out by David Miller.
Now, this patch re-introduces the checks (at this point we check
port->state, not the tty proper, as we do not care about tty pointers
anymore). For both of the drivers, we place the check below the
handling of break signal so that sysrq can actually work. (One needs
to issue a break and then sysrq key within the following 5 seconds.)
We do not change sc26xx, sunhv, and sunsu here because they behave the
same as before. People having that hardware should fix the driver
eventually, however. They always could unconditionally dereference tty
in receive_chars, port->state in uart_handle_dcd_change, and
up->port.state->port.tty.
There is perhaps more to fix in all those drivers, but they are at
least in a state they were before.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple users of this file from different source
paths now, and rather than have ../ paths in include statements,
just move the file to the linux header dir.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of users of of_platform_driver in drivers/serial. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
