This reverts commit a86713b153.
Kevin Hilman writes:
Multiple boot failures on ARM[1] were bisected down to this
patch.
How was this patch tested, and on which platforms?
Also, the changelog states that this should be done only for
UART_CAP_SLEEP, but the patch does it for every UART.
Greg, I suggest this patch be dropped from tty-next until it has
been better described and tested.
[1] http://lists.linaro.org/pipermail/kernel-build-reports/2014-October/005550.html
Reported-by: Kevin Hilman <khilman@kernel.org>
Cc: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For console devices having UART_CAP_SLEEP capability, the uart_pm_state has
to be initialized to UART_PM_STATE_ON. Otherwise the LCR regiser values
are reinitialized when uart_change_pm is called from uart_configure_port.
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_set_termios() is called with interrupts enabled; no need to
save and restore the interrupt state when taking the uart port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->hw_stopped is not used by the tty core and is thread-unsafe;
hw_stopped is a member of a bitfield whose fields are updated
non-atomically and no lock is suitable for serializing updates.
Replace serial core usage of tty->hw_stopped with uport->hw_stopped.
Use int storage which works around Alpha EV4/5 non-atomic byte storage,
since uart_port uses different locks to protect certain fields within the
structure.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core uses the tty port flags, ASYNC_CTS_FLOW and
ASYNC_CD_CHECK, to track whether CTS and DCD changes should be
ignored or handled. However, the tty port flags are not safe for
atomic bit operations and no lock provides serialized updates.
Introduce the struct uart_port status field to track CTS and DCD
enable states, and serialize access with uart port lock. Substitute
uart_cts_enabled() helper for tty_port_cts_enabled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core provides two helper functions, uart_handle_dcd_change()
and uart_handle_cts_change(), for UART drivers to use at interrupt
time. The serial core expects the UART driver to hold the uart port lock
when calling these helpers to prevent state corruption.
If lockdep enabled, trigger a warning if the uart port lock is not held
when calling these helper functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for spin lock assertion; move non-trivial assignment into
function body.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_unthrottle() attempts to avoid sending START and the previous
x_char if the previous x_char has not yet been sent. However, this
optimization could leave the sender in a throttled state; for example,
if the sender is throttled and this unthrottle coincides with a manual
tcflow(TCION) from user-space, then neither START would be sent.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UART driver is expected to clear port->x_char after
transmission while holding the port->lock. However, the serial
core fails to take the port->lock before assigning port->xchar.
This allows for the following race
CPU 0 | CPU 1
|
| serial8250_handle_irq
| ...
| serial8250_tx_chars
| if (port->x_char)
| serial_out(up, UART_TX, port->x_char)
uart_send_xchar |
port->x_char = ch |
| port->x_char = 0
port->ops->start_tx() |
|
The x_char on CPU 0 will never be sent.
Take the port->lock in uart_send_xchar() before assigning port->x_char.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 06aa82e498.
This commit purports to enable auto CTS flow control for the 8250
UART driver. However, the 8250 UART driver already supports auto
CTS flow control via UART_CAP_AFE and UART_CAP_EFR. Indeed, this
patch introduces another DT attribute for which an existing firmware
flag already exists ("auto-flow-control"). Furthermore, the use of
UPF_HARD_FLOW requires the UART driver to define .throttle and
.unthrottle methods, neither of which are defined for the 8250 UART
driver (which will result in a NULL ptr dereference). Finally, this patch
supposes to fix existing bugs in the serial core for auto CTS-enabled
hardware, but does not include the class of hardware for which these
bugs exist.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
printk replaced with corresponding dev_* .
fixed two broken user-visible strings used by the corresponding printk.
the null check for uport->dev and port->dev is removed as dev_* will check for
null while printing.
printing of dev_name(uport->dev) and dev_name(port->dev) also removed as those
are being printed by dev_* .
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
Current code allocates too much data for tty_groups member of uart_port struct,
so fix it.
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some serial drivers (like 8250), want to add sysfs files. We need to do
so in a race-free way, so allow any port to be able to specify an
attribute group that should be added at device creation time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uart port drivers may reconfigure termios settings based on available
hardware support; set/clear ASYNC_CTS_FLOW and ASYNC_CHECK_CD _after_
calling the port driver's .set_termios method.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since at least before 2.6.30, it has not been possible to observe
a hung up file pointer in a tty driver's open() method unless/until
the driver open() releases the tty_lock() (eg., before blocking).
This is because tty_open() adds the file pointer while holding
the tty_lock() _and_ doesn't release the lock until after calling
the tty driver's open() method. [ Before tty_lock(), this was
lock_kernel(). ]
Since __tty_hangup() first waits on the tty_lock() before
enumerating and hanging up the open file pointers, either
__tty_hangup() will wait for the tty_lock() or tty_open() will
not yet have added the file pointer. For example,
CPU 0 | CPU 1
|
tty_open | __tty_hangup
.. | ..
tty_lock | ..
tty_reopen | tty_lock / blocks
.. |
tty_add_file(tty, filp) |
.. |
tty->ops->open(tty, filp) |
tty_port_open |
tty_port_block_til_ready |
.. |
while (1) |
.. |
tty_unlock | / unblocks
schedule | for each filp on tty->tty_files
| f_ops = tty_hung_up_fops;
| ..
| tty_unlock
tty_lock |
.. |
tty_unlock |
Note that since tty_port_block_til_ready() and similar drop
the tty_lock while blocking, when woken, the file pointer
must then be tested for having been hung up.
Also, fix bit-rotted drivers that used extra_count to track the
port->count bump.
CC: Mikael Starvik <starvik@axis.com>
CC: Samuel Ortiz <samuel@sortiz.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->closing informs the line discipline that the hardware will
be shutting down imminently, and to disable further input other
than soft flow control (but to still allow additional output).
However, the tty lock is the necessary lock for preventing
concurrent changes to tty->closing. As shown by the call-tree
audit [1] of functions that modify tty->closing, the tty lock
is already held for those functions.
[1]
Call-tree audit of functions that modify tty->closing
* does not include call tree to tty_port_close(), tty_port_close_start(),
or tty_port_close_end() which is already documented in
'tty: Document locking for tty_port_close{,start,end}' that shows
callers to those 3 functions hold the tty lock
tty_release()
tty->ops->close() --+
|
__tty_hangup() |
tty->ops->close() --+
|
mp_close():drivers/staging/sb105x/sb_pci_mp.c
dngc_tty_close():drivers/staging/dgnc/dgnc_tty.c
dgap_tty_close():drivers/staging/dgap/dgap_tty.c
dgrp_tty_close():drivers/staging/dgrp/dgrp_tty.c
rp_close():drivers/tty/rocket.c
hvsi_close():drivers/tty/hvc/hvsi.c
rs_close():drivers/tty/serial/68328serial.c
rs_close():drivers/tty/serial/crisv10.c
uart_close():drivers/tty/serial/serial_core.c
isdn_tty_close():drivers/isdn/i4l/isdn_tty.c
tty3215_close():drivers/s390/char/con3215.c
tty_open()
tty_ldisc_setup() ----+
|
__tty_hangup() |
tty_ldisc_hangup() ---+
|
tty_set_ldisc() --------+
tty_ldisc_restore() --+
|
+- tty_ldisc_open()
ld->ops->open() --+
|
+- n_tty_open()
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a tty is opened for the serial console, the termios c_cflag
settings are inherited from the console line settings.
However, if the tty is subsequently closed, the termios settings
are lost. This results in a garbled console if the console is later
suspended and resumed.
Preserve the termios c_cflag for the serial console when the tty
is shutdown; this reflects the most recent line settings.
Fixes: Bugzilla #69751, 'serial console does not wake from S3'
Reported-by: Valerio Vanni <valerio.vanni@inwind.it>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes enable_ms() optional, so we can eliminate a lot of
empty enable_ms() implementations from driver code.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the devicetree specifies a serial port as a stdout device, then the
kernel can use it as the default console if nothing else was selected on
the command line. For any serial port that uses the uart_add_one_port()
feature, the uart_add_one_port() has all the information needed to
automatically enable the console device, which is what this patch does.
With this change applied, a device tree platform can be booted without
any console= parameters on the command line and the kernel will still be
able to determine its console.
Tested on QEMU Versatile model and i.MX
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
8250 uart driver currently supports only software assisted hw flow
control. The software assisted hw flow control maintains a hw_stopped
flag in the tty structure to stop and start transmission and use modem
status interrupt for the event to drive the handshake signals. This is
not needed if hw has flow control capabilities. This patch adds a
DT attribute for enabling hw flow control for a uart port. Also skip
stop and start if this flag is present in flag field of the port
structure.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In (efe2f29 kgdboc,kdb: Allow kdb to work on a non open console port)
support was added to directly use the "write_char" functions when
doing kdb over a non-open console port. This is great, but it ends up
bypassing the normal code in uart_console_write() that adds a carriage
return before any newlines.
There appears to have been a trend to add this support directly in
some console driver's poll_put_char() functions. This had a few side
effects, including:
- In this case we were doing LFCR, not CRLF. This was fixed in
uart_console_write() back in (d358788 [SERIAL] kernel console should
send CRLF not LFCR)
- Not all serial drivers had the LFCR code in their poll_put_char()
functions. In my case I was running serial/samsung.c which lacked
it.
I've moved the handling to uart_poll_put_char() to fix the above
problems. Now when I use kdb (and don't point console= to the same
UART) I no longer get:
[0]kdb>
[0]kdb>
[0]kdb>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While porting a RS485 driver from 2.6.29 to 3.14, i noticed that the serial tty
driver could break it by using uart ports that it does not own :
1. uart_change_pm ist called during uart_open and calls the uart pm function
without checking for PORT_UNKNOWN.
The fix is to move uart_change_pm from uart_open to uart_port_startup.
2. The return code from the uart request_port call in uart_set_info is not
handled properly, leading to the situation that the serial driver also
thinks it owns the uart ports.
This can triggered by doing following actions :
setserial /dev/ttyS0 uart none # release the uart ports
modprobe lirc-serial # or any other device that uses the uart
setserial /dev/ttyS0 uart 16550 # gives no error and the uart tty driver
# can use the ports as well
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is closed, uart_close() takes care of shutting down the
hardware, and powering it down.
When a serial port is unbound while in use, uart_close() bypasses all of
this, as this is supposed to be done through uart_hangup() (invoked via
tty_vhangup() in uart_remove_one_port()).
However, uart_hangup() does not set the hardware's power state, leaving it
powered up. This may also lead to unbounded nesting counts in clock and
power management, depending on their internal implementation.
Make sure to power down the port in uart_hangup(), except when the port is
used as a serial console.
For serial consoles, this operation must be postponed until after the port
becomes completely unused. This case is not fixed yet, as it depends on a
(future) fix for the tty->count vs. port->count imbalance on failed
uart_open().
After this, the module clock used by the sh-sci driver is disabled on
unbind while the serial port is in use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial_core ring buffer empties just as the tty layer receives
an XOFF, then start_tx will never be called when the tty layer
receives an XON as the serial_core ring buffer is empty. This will
possibly leave a few bytes trapped in the fifo for drivers that
disable the transmitter when flow controlled.
Signed-off-by: Seth Bollinger <sethb@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding a serial driver that's being used as a serial console,
the kernel may crash with a NULL pointer dereference in a uart_*() function
called from uart_close () (e.g. uart_flush_buffer() or
uart_chars_in_buffer()).
To fix this, let uart_close() check for port->count == 0. If this is the
case, bail out early. Else tty_port_close_start() will make the port
counts inconsistent, printing out warnings like
tty_port_close_start: tty->count = 1 port count = 0.
and
tty_port_close_start: count = -1
and once uport == NULL, it will also crash.
Also fix the related crash in pr_debug() by checking for a non-NULL uport
first.
Detailed description:
On driver unbind, uart_remove_one_port() is called. Basically it;
- marks the port dead,
- calls tty_vhangup(),
- sets state->uart_port = NULL.
What will happen depends on whether the port is just in use by e.g. getty,
or was also opened as a console.
A. If the tty was not opened as a console:
- tty_vhangup() will (in __tty_hangup()):
- mark all file descriptors for this tty hung up by pointing them to
hung_up_tty_fops,
- call uart_hangup(), which sets port->count to 0.
- A subsequent uart_open() (this may be through /dev/ttyS*, or through
/dev/console if this is a serial console) will fail with -ENXIO as the
port was marked dead,
- uart_close() after the failed uart_open() will return early, as
tty_hung_up_p() (called from tty_port_close_start()) will notice it was
hung up.
B. If the tty was also opened as a console:
- tty_vhangup() will (in __tty_hangup()):
- mark non-console file descriptors for this tty hung up by pointing
them to hung_up_tty_fops,
- NOT call uart_hangup(), but instead call uart_close() for every
non-console file descriptor, so port->count will still have a
non-zero value afterwards.
- A subsequent uart_open() will fail with -ENXIO as the port was
marked dead,
- uart_close() after the failed uart_open() starts to misbehave:
- tty_hung_up_p() will not notice it was hung up,
- As port->count is non-zero, tty_port_close_start() will decrease
port->count, making the tty and port counts inconsistent. Later,
warnings like these will be printed:
tty_port_close_start: tty->count = 1 port count = 0.
and
tty_port_close_start: count = -1
- If all of this happens after state->uart_port was set to zero, a
NULL pointer dereference will happen.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port being removed is used as a console, it must also be
unregistered from the console subsystem using unregister_console().
uart_ops.release_port() will release resources (e.g. iounmap() the serial
port registers), causing a crash on subsequent kernel output if the console
is still registered.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_set_options() code unconditionally initalizes the spinlock
on the port. This can cause a deadlock in some situations.
One instance that exposed the problem, was when writing to
/sys/module/kgdboc/parameters/kgdboc to use ttyS0 when the console
is already running on ttyS0. If the spinlock is re-initialized
while the lock is held due to output to the console, there
is a deadlock.
Assume the spinlock is initialized if the port is a console.
Signed-off-by: Randy Witt <rewitt@declaratino.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some serial ports will not use the standard base baud rate. Report
this after initialization so it might be discovered and used for early
console configuration.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move "uart_console" definition to serial core header file, so that it can be
used by serial drivers.
Get rid of the uart_console defintion from mpc52xx_uart driver.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra nayak <rnayak@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
The serial core uses device_find_child() but does not drop the reference to
the retrieved child after using it. This patch add the missing put_device().
What I have done to test this issue.
I used a machine with an AMBA PL011 serial driver. I tested the patch on
next-20120408 because the last branch [next-20120415] does not boot on this
board.
For test purpose, I added some pr_info() messages to print the refcount
after device_find_child() (lines: 1937,2009), and after put_device()
(lines: 1947, 2021).
Boot the machine *without* put_device(). Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 87.058575] uart_suspend_port:1937 refcount 4
[ 87.058582] uart_suspend_port:1947 refcount 4
[ 87.098083] uart_resume_port:2009refcount 5
[ 87.098088] uart_resume_port:2021 refcount 5
echo disk > /sys/power/state
[ 103.055574] uart_suspend_port:1937 refcount 6
[ 103.055580] uart_suspend_port:1947 refcount 6
[ 103.095322] uart_resume_port:2009 refcount 7
[ 103.095327] uart_resume_port:2021 refcount 7
echo disk > /sys/power/state
[ 252.459580] uart_suspend_port:1937 refcount 8
[ 252.459586] uart_suspend_port:1947 refcount 8
[ 252.499611] uart_resume_port:2009 refcount 9
[ 252.499616] uart_resume_port:2021 refcount 9
The refcount continuously increased.
Boot the machine *with* this patch. Then:
echo reboot > /sys/power/disk
echo disk > /sys/power/state
[ 159.333559] uart_suspend_port:1937 refcount 4
[ 159.333566] uart_suspend_port:1947 refcount 3
[ 159.372751] uart_resume_port:2009 refcount 4
[ 159.372755] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 185.713614] uart_suspend_port:1937 refcount 4
[ 185.713621] uart_suspend_port:1947 refcount 3
[ 185.752935] uart_resume_port:2009 refcount 4
[ 185.752940] uart_resume_port:2021 refcount 3
echo disk > /sys/power/state
[ 207.458584] uart_suspend_port:1937 refcount 4
[ 207.458591] uart_suspend_port:1947 refcount 3
[ 207.498598] uart_resume_port:2009 refcount 4
[ 207.498605] uart_resume_port:2021 refcount 3
The refcount correctly handled.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
hardpps() functionality is provided through the N_PPS line
discipline now. The new function signature was added in commit
025b40ab (2011-01-12). There was no previous macro or
function hardpps(), at least since before the initial commit of
v2.6.12 in 2005. It's unlikely this code has been compiled since.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An extension of the previous commit, there is no semantic change
here, just fewer lines of source code.
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PPS (Pulse-Per-Second) line discipline has developed a number of
unhealthy attachments to core tty data and functions, ultimately leading
to its breakage.
The previous patches fixed the crashing. This one reduces coupling further
by eliminating the timestamp parameter from the dcd_change ldisc method.
This reduces header file linkage and makes the extension more generic,
and the timestamp read is delayed only slightly, from just before the
ldisc->ops->dcd_change method call to just after.
Fix attendant build breakage in
drivers/tty/n_tty.c
drivers/tty/tty_buffer.c
drivers/staging/speakup/selection.c
drivers/staging/dgrp/dgrp_*.c
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@braille.uwo.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: George Spelvin <linux@horizon.com>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for extern function uart_remove_one_port:
need check pointer whether be NULL, before the main work.
just like what the other extern function uart_add_one_port has done.
uart_add_one_port and uart_remove_one_port are pair
information:
for the callers (such as drivers/tty/serial/jsm: jsm_tty.c, jsm_driver.c)
they realy assume that:
they still can call uart_remove_one_port, after uart_add_one_port failed
we (as an extern function), have to understand it (just like kfree).
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One point is to have less places where we actually need tty pointer.
The other is that low_latency is bound to buffer processing and
buffers are now in tty_port. So it makes sense to move low_latency to
tty_port too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core is using power states lifted from ACPI for no
good reason. Remove this reference from the documentation and
alter all users to use an enum specific to the serial core
instead, and define it in <linux/serial_core.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ARM OMAP serial updates from Russell King:
"This series is a major reworking of the OMAP serial driver code fixing
various bugs in the hardware-assisted flow control, extending up into
serial_core for a couple of issues. These fixes have been done as a
set of progressive changes and transformations in the hope that no new
bugs will be introduced by this series.
The problems are many-fold, from the driver not being informed about
updated settings, to the driver not knowing what the intentions of the
upper layers are.
The first four patches tackle the serial_core layer, allowing it to
provide the necessary information to drivers, and the remaining
patches allow the OMAP serial driver to take advantage of this.
This brings hardware assisted RTS/CTS and XON/OFF flow control into a
useful state.
These patches have been in linux-next for most of the last cycle;
indeed they predate the previous merge window. They've also been
posted to the OMAP people."
* 'omap-serial' of git://git.linaro.org/people/rmk/linux-arm: (21 commits)
SERIAL: omap: fix hardware assisted flow control
SERIAL: omap: simplify (2)
SERIAL: omap: move xon/xoff setting earlier
SERIAL: omap: always set TCR
SERIAL: omap: simplify
SERIAL: omap: don't read back LCR/MCR/EFR
SERIAL: omap: serial_omap_configure_xonxoff() contents into set_termios
SERIAL: omap: configure xon/xoff before setting modem control lines
SERIAL: omap: remove OMAP_UART_SYSC_RESET and OMAP_UART_FIFO_CLR
SERIAL: omap: move driver private definitions and structures to driver
SERIAL: omap: remove 'irq_pending' bitfield
SERIAL: omap: fix MCR TCRTLR bit handling
SERIAL: omap: fix set_mctrl() breakage
SERIAL: omap: no need to re-read EFR
SERIAL: omap: remove setting of EFR SCD bit
SERIAL: omap: allow hardware assisted IXANY mode to be disabled
SERIAL: omap: allow hardware assisted rts/cts modes to be disabled
SERIAL: core: add throttle/unthrottle callbacks for hardware assisted flow control
SERIAL: core: add hardware assisted h/w flow control support
SERIAL: core: add hardware assisted s/w flow control support
...
Conflicts:
drivers/tty/serial/omap-serial.c
serial_core.c usually does
if (HIGH_BITS_OFFSET)
expr-involving-HIGH_BITS_OFFSET()
at least to avoid generating useless code on 32-bit machines, where
HIGH_BITS_OFFSET is zero. Do that in uart_get_attr_port().
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this we will shift data into oblivion and give wrong results on
some configurations
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
