The macro has been accounting for DRM_COMMAND_BASE for a long time
now so there's no reason to still be duplicating it. Plus we were
leaving the name undefined which meant that all the DRM ioctl
warnings/errors were always listing "null" ioctl at the culprit.
This fixes the undefined ioctl name and removes duplicated code.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723165153.113198-1-zackr@vmware.com
Commit 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing +
selftests") added some debug code for sideband message tracing. But
it seems to have unintentionally changed the behavior on sideband message
failure. It catches and returns failure only if DRM_UT_DP is enabled.
Otherwise it ignores the error code and returns success. So on an MST
unplug, the caller is unaware that the clear payload message failed and
ends up waiting for 4 seconds for the response. Fixes the issue by
returning the proper error code.
Changes in V2:
-- Revise commit text as review comment
-- add Fixes text
Changes in V3:
-- remove "unlikely" optimization
Fixes: 2f015ec6ea ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1625585434-9562-1-git-send-email-khsieh@codeaurora.org
There is some sort of corner case behavior of the controller,
which could rarely be triggered at least on i.MX6SX connected
to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS
bridged 1920x1080 panel (and likely on other setups too), where
the image on the panel shifts to the right and wraps around.
This happens either when the controller is enabled on boot or
even later during run time. The condition does not correct
itself automatically, i.e. the display image remains shifted.
It seems this problem is known and is due to sporadic underflows
of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow
IRQs, neither of the IRQs trigger and neither IRQ status bit is
asserted when this condition occurs.
All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW
bit, which is described in the reference manual since i.MX23 as
"
Set this bit to enable the LCDIF block to recover in the next
field/frame if there was an underflow in the current field/frame.
"
Enable this bit to mitigate the sporadic underflows.
Fixes: 45d59d7040 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224701.189289-1-marex@denx.de
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
There's two stages of manual upload/invalidate displays:
- just handling dirtyfb and uploading the entire fb all the time
- looking at damage clips
In the latter case we support it through fbdev emulation (with
fb_defio), atomic property, and with the dirtfy clip rects.
Make sure at least the atomic property is set up as the main official
interface for this. Ideally we'd also check that
drm_atomic_helper_dirtyfb() is used and that fbdev defio is set up,
but that's quite a bit harder to do. Ideas very much welcome.
From a cursor audit drivers seem to be getting this right mostly, but
better to make sure. At least no one is bypassing the accessor
function.
v2:
- use drm_warn_once with a meaningful warning string (José)
- don't splat in the atomic check code for everyone (intel-gfx-ci)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-2-daniel.vetter@ffwll.ch
Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.
1. DSI panels and bridges will invoke the host attach
from probe in order to find the panel_or_bridge.
chipone_probe()
dw_mipi_dsi_host_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_host_attach().start
chipone_attach(). start
chipone_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
2. I2C based DSI bridge will invoke the drm_bridge_attach
from bridge attach in order to find the panel_or_bridge.
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
dw_mipi_dsi_host_attach().start
sn65dsi83_attach(). start
sn65dsi83_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com
SoCs like the rk3288 and rk3399 have 3 mipi dphys on them. One is TX-
only, one is RX-only and one can be configured to do either TX or RX.
The RX phy is statically connected to the first Image Signal Processor,
the TX phy is statically connected to the first DSI controller and
the TXRX phy is connected to both the second DSI controller as well
as the second ISP.
The RX dphy is controlled externally through registers in the "General
Register Files", while the other two are controlled through the
"Configuration and Test Interface" inside their DSI controller's
io-memory area.
The Rockchip dw-dsi controller already controls these dphys for the
TX case in the driver, but when we want to also allow configuration
for RX to the ISP from the media subsystem we need to expose phy-
functionality instead.
So add a bit of infrastructure to allow the dsi driver to work as a
phy and make sure it can be only one or the other at a time.
Similarly as the dsi-controller will be part of the drm-graph when
active, add an empty component to the drm-graph when in phy-mode
to make the rest of the drm-graph not wait for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Tested-by: Sebastian Fricke <sebastian.fricke@posteo.net>
Acked-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210210111020.2476369-4-heiko@sntech.de
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
v3:
* return error if (ret < 0) (Geert)
* remove duplicate error message (Geert)
v2:
* handle errors in platform_get_irq() (Geert, Sergei)
* store IRQ number in struct shmob_drm_device (Laurent)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210720080941.23646-1-tzimmermann@suse.de
Replace dma_buf_begin_cpu_access() with drm_gem_fb_begin_cpu_access();
same for _end_cpu_access(). Remove some boiler-plate code. No functional
changes.
There's one left-over reference to the imported attachment that we
keep. GEM BOs with imported attachment are considered uncached and
enables special handling within the drm_fb_swab().
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-4-tzimmermann@suse.de
Implement helpers drm_gem_fb_begin_cpu_access() and _end_cpu_access(),
which call the rsp dma-buf functions for all GEM BOs of the given
framebuffer.
Calls to dma_buf_end_cpu_access() can return an error code on failure,
while drm_gem_fb_end_cpu_access() does not. The latter runs during DRM's
atomic commit or during cleanup. Both cases don't allow for errors, so
leave out the return value.
v2:
* fix typo in docs (Daniel)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210716140801.1215-2-tzimmermann@suse.de
drm-misc-next for v5.15-rc1:
UAPI Changes:
- Remove sysfs stats for dma-buf attachments, as it causes a performance regression.
Previous merge is not in a rc kernel yet, so no userspace regression possible.
Cross-subsystem Changes:
- Sanitize user input in kyro's viewport ioctl.
- Use refcount_t in fb_info->count
- Assorted fixes to dma-buf.
- Extend x86 efifb handling to all archs.
- Fix neofb divide by 0.
- Document corpro,gm7123 bridge dt bindings.
Core Changes:
- Slightly rework drm master handling.
- Cleanup vgaarb handling.
- Assorted fixes.
Driver Changes:
- Add support for ws2401 panel.
- Assorted fixes to stm, ast, bochs.
- Demidlayer ingenic irq.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2d0d2fe8-01fc-e216-c3fd-38db9e69944e@linux.intel.com
Add support for board power calibration on Aldebaran.
Board calibration is done after DC offset calibration.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.
[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.
[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.
Put in a hardcoded default until we have the interface in place.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.
[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
