Add support for the imx6ul pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the imx7d pico board with nymph baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the imx7d pico board with dwarf baseboard combination.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Olimex Olinuxino board has a user led connected to SSP1_DETECT.
But since this pin is listed in mmc0_pins_fixup, it is already claimed
by MMC driver and this results in this error during boot:
[ 1.390000] imx23-pinctrl 80018000.pinctrl: pin SSP1_DETECT already
requested by 80010000.spi; cannot claim for leds
[ 1.400000] imx23-pinctrl 80018000.pinctrl: pin-65 (leds) status -22
[ 1.410000] imx23-pinctrl 80018000.pinctrl: could not request pin 65
(SSP1_DETECT) from group led_gpio2_1.0 on device 80018000.pinctrl
[ 1.420000] leds-gpio leds: Error applying setting, reverse things back
[ 1.430000] leds-gpio: probe of leds failed with error -22
This fix it, introduce mmc0_sck_cfg and switch the Olinuxino board to it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "aspeed,vhub-downstream-ports" and "aspeed,vhub-generic-endpoints"
properties to describe supported number of vhub ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add "aspeed,vhub-downstream-ports" and "aspeed,vhub-generic-endpoints"
properties to describe supported number of vhub ports and endpoints.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add support of early console for STM32MP1. Default UART instance is UART4,
but other UART instances can be configured by setting physical and virtual
base addresses in menuconfig.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support of early console for STM32H7. Default UART instance is USART1,
but other UART instances can be configured by setting physical and virtual
base addresses in menuconfig.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Early console is hardcoded on USART1 in current implementation.
With this patch, default UART instance is USART1, but other UART instances
can be configured by setting physical and virtual base addresses in
menuconfig.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Early console is hardcoded on USART1 in current implementation.
With this patch, default UART instance is USART1, but other UART instances
can be configured by setting physical and virtual base addresses in
menuconfig.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On those boards, as stated in schematics files, the regulator used for IOs
is VDD. It was wrongly set to v3v3.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On STM32MP1 DK1, DK2, ED1 and EV1 boards, there is only a micro SD socket.
This is also the case on Avenger board.
They don't support the Write Protect pin.
The disable-wp is then added in the SD-cards sdmmc1 nodes.
This avoids executing some code and a warning during driver probe.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The broken-cd properties are replaced with cd-gpios, with the correct
GPIO to detect the card insertion. The GPIO lines require a pull-up.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Remove unused properties from stpmic node.
The issues have been detected by running dtbs_check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the wakeup-source property in all i2c nodes of
the SoC stm32mp157c so that those I2C controllers can become
wakeup-source.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp157c-ed1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
DRA7 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Issues ere observed only with SATA on DRA7-EVM with 4GB RAM
and CONFIG_ARM_LPAE enabled. This is because the controller
supports 64-bit DMA and its driver sets the dma_mask to 64-bit
thus resulting in DMA accesses beyond L3 limit of 2G.
Setting the correct bus_dma_limit fixes the issue.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the sleep state pinctrl entry for the i2c2 and i2c5 nodes
of the stm32mp157c-ev1 board.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add the sleep state pinctrl entry for the i2c4 node
of the stm32mp15xx-dkx.dtsi
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On DK boards, all I2C4 bus slaves supports I2C Fast Mode hence setting
the bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
On this board, the I2C4 bus has only a single slave (pmic) which
supports I2C Fast Mode hence setting bus frequency to 400 KHz.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Tegra20/30/114/124 SoCs have common idling states, thus there is no much
point in having separate drivers for a similar hardware. This patch moves
Tegra114/124 arch/ drivers into the common driver without any functional
changes. The CC6 state is kept disabled on Tegra114/124 because the core
Tegra PM code needs some more work in order to support that state.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra20 and Terga30 SoCs have common C1 and CC6 idling states and thus
share the same code paths, there is no point in having separate drivers
for a similar hardware. This patch merely moves functionality of the old
driver into the new, although the CC6 state is kept disabled for now since
old driver had a rudimentary support for this state (allowing to enter
into CC6 only when secondary CPUs are put offline), while new driver can
provide a full-featured support. The new feature will be enabled by
another patch.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver's code is refactored in a way that will make it easy to
support Tegra30/114/124 SoCs by this unified driver later on. The
current functionality is equal to the old Tegra20 driver, only the
code's structure changed a tad. This is also a proper platform driver
now.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
clk_out_1, clk_out_2, and clk_out_3 are part of Tegra PMC block but were
previously erroneously provided by the clock and reset controller.
clk_out_1 is dedicated for audio mclk on Tegra30 through Tegra210.
This patch updates device tree sound node to use clk_out_1 from the PMC
provider as mclk and uses assigned-clock properties to specify clock
parents for clk_out_1 and extern1.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC has clk_out_1, clk_out_2, clk_out_3, and blink clock.
These clocks were erroneously provided by the clock and reset controller
and are now provided by the PMC instead because that's where the primary
controls are.
This patch adds #clock-cells property with 1 clock specifier to the
Tegra PMC node in device tree.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Jetson TK1 USB 2-0 port is controlled by phy-tegra-usb driver
rather than padctl driver. Remove the entry for the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Replace memory accessors with atomic API just to make code consistent
with the abort_barrier. The new variant may be even more correct now
since atomic_read() will prevent compiler from generating wrong things
like carrying abort_flag value in a register instead of re-fetching it
from memory.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The outer_disable() of Tegra's suspend code is open-coded now since
that helper produces spurious warning message about secondary CPUs being
online when CPU enters into LP2 from cpuidle. The secondaries are actually
halted by the cpuidle driver on entering into LP2 idle-state, but the
online status is not touched by the cpuidle. This fixes a storm of
warnings once LP2 idling state is enabled on Tegra30. The outer_disable()
helper has sanity checks for interrupts and secondary CPUs being disabled
and we are pretty confident about the interrupts state during of CPU
idling / system suspend. The rail-off status check is added in this patch
as equivalent for the "num_online_cpus() > 1".
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The upcoming unified CPUIDLE driver will be added to the drivers/cpuidle/
directory and it will require all these exposed Tegra PM-core functions.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: fixup missing include rename]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Define the sdhci pinctrl state as "default" so it gets applied
correctly and to match all other RPis.
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The tst menomic has only a single #<const> argument in Thumb mode. There
is an ARM variant which allows to write #<const> as #<byte>, #<rot>
which probably is where the current syntax comes from.
It seems that binutils does not care about the additional parameter.
Clang however complains in Thumb2 mode:
arch/arm/kernel/relocate_kernel.S:28:12: error: too many operands for
instruction
tst r3,#1,0
^
Drop the unnecessary parameter. This fixes building this file in Thumb2
mode with the Clang integrated assembler.
Link: https://github.com/ClangBuiltLinux/linux/issues/770
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The Tegra30 CPUIDLE driver has intention to check whether primary CPU was
the last CPU that entered LP2 (CC6) idle-state, but that functionality
never got utilized because driver never supported the CC6 state for the
case where any secondary CPU is online. The new cpuidle driver will
properly support CC6 on Tegra30, including the case where secondary CPUs
are online, and that knowledge about what CPUs entered into CC6 won't be
needed at all because new driver will use different approach by making use
of the coupled idle-state and explicitly parking secondary CPUs before
entering into CC6. Thus this patch is just a minor cleanup change.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pen-locking is meant to block CPU0 if CPU1 wakes up during of entering
into LP2 because of some interrupt firing up, preventing unnecessary LP2
enter that will be resumed immediately. Apparently this case doesn't
happen often in practice, I checked how often it takes place and found
that after ~20 hours of browsing web, managing email, watching videos and
idling (15+ hours) there is only a dozen of early LP2 entering abortions
and they all happened while device was idling. Thus let's remove the
pen-locking and make LP2 entering uninterruptible, simplifying code quite
a lot. This will also become very handy for the upcoming unified cpuidle
driver, allowing to have a common LP2 code-path across of different
hardware generations.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function resembles tegra_cpu_die() of the hotplug code, but
this variant is more suitable to be used for CPU PM because it's made
specifically to be used by cpu_suspend(). In short this function puts
secondary CPU offline, it will be used by the new CPUIDLE driver.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The sleep-tegra*.S provides functionality required for suspend/resume
and CPU hotplugging. The new unified CPUIDLE driver will support multiple
hardware generations starting from Terga20 and ending with Tegra124, the
driver will utilize functions that are provided by the assembly and thus
it is cleaner to compile that code without any build-dependencies in order
to avoid churning with #ifdef's.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
