Host platforms such as routers supported by OpenWRT can
support NVRAM reading directly from internal NVRAM store.
With this patch the nvram load routines will fall back to
this method when there is no nvram file and support is
available in the kernel.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The event mask length is determined by the highest event number
that is specified in the driver. When this length is shorter than
firmware expects setting event mask will fail and device becomes
pretty useless. This issue was reported with bcm4339 firmware that
was recently released.
Reported-by: Pontus Fuchs <pontusf@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_flowring_block blocks the last active flowring under the same
interface instead of the one provided by caller. This could lead to a
dead lock of netif stop if there are more than one flowring under the
interface and the traffic is high enough so brcmf_flowring_enqueue can
not unblock the ring right away.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cfg80211_check_combinations() so we can bail out early when an
interface add or change results in an invalid combination.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Expose ring buffer read/write pointers and other useful statistics
through debugfs.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The interface combination provided by brcmfmac did not truly reflect
the combinations supported by driver and/or firmware.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Broadcom is working on better reflection of interface combinations. With
upcoming patches we may have 1st combination supporting less interfaces
than others.
To don't run out of addresses check all combinations to find the one
with the greatest max_interfaces value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
current code will handle -ETIMEDOUT as success which is probalbly wrong.
According to this comment I assume it is safe to handle -ETIMEDOUT as false:
drivers/net/wireless/ath/ath9k/calib.c
290 /*
291 * We timed out waiting for the noisefloor to load, probably due to an
292 * in-progress rx. Simply return here and allow the load plenty of time
293 * to complete before the next calibration interval. We need to avoid
294 * trying to load -50 (which happens below) while the previous load is
295 * still in progress as this can cause rx deafness. Instead by returning
296 * here, the baseband nf cal will just be capped by our present
297 * noisefloor until the next calibration timer.
298 */
Since no other error wariants are present, this patch is checking only
for (ret <= 0).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV2ZpTAAoJEC0Llv5uNjIBe5cP/jlQtTV2mwiRg+2T9ZP3j4aB
kx+g3Rb0NtAM09M/6hO6pqyvBDRrqGLCvqnUemCPYeyoctG4zhpS3S6xWytHPxHk
9jbJxeFzU7Y8rVkYf0padXqfQfgyiqH8+QNgtV/bf6Lj5/ETjptWPzREM6T2Krsr
3JltroO6Ra02MQP9nrTKHsTQH7zZxGubo5KHw4sff6fge4BCldX1+W7vLzBIzOs9
NGKBgticBE6Lx9cbbdr4N26gl8pM+Ed1AdblFoVIUlkYu1WooxSBTD2/GfnjzT5l
MeB+BE34RF9fouN0eBNe9IkgC5xM8jXDgMx6ZrM9l3TPmsD0SDoZb3MFTUBFakuY
oAXgrM7bxkYABpMT7a12s6IKE0C5/PmpVZIy34sG+jQFmBDjV9wZWj5yVn49KGUU
j0SMxlGdARzYYUS1NQZjC2pKfEWQCSa2cRelvi2g01bddGwyceTZ7ge4p1J5BeQ6
m86u3TvsxkNq1WyLyVeiQFSxL/zRZSnpVGm20WJ7OXjlHzQg+0khC5m877vRF1ka
VjbNQRP03R1bj74UU6lcpEun9hnmWYEhUXaLFVMUjF9cIoYXI8cXOPwhLkpUjKFR
nZrEDT7AXbwXQq5s78tlUZIUJ48rd1qzDu9TkYKx8J8IgYyBLXMoyV8ANFZ0CRWm
0SDiEfrd4LJ2zt8ZztoE
=2eAA
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-23' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware
Add support for the new (bigger) TX power command. This doesn't
actually take advantage of the new capabilities (to set per-chain
TX power limits) but makes the code compatible with newer firmware
images expecting the larger command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
split long debug messages that may result warning in tracing.
Fixes: 1a84e77160 ("iwlwifi: mvm: add debug info to schedule scan complete message.")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The command string array is assumed to be indexable by a full u8, so it
must have 256 entries (0-255), not just 255. A recent firmware change
(apparently) started using the command 0xff for a notification to the
host, causing the driver to crash in debug message/tracing code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when waking from d0i3 there is a wakeup reason.
Enum in driver is not up to date with FW api - fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
My static checker complains that we don't check for underflows in
iwl_dbgfs_fw_dbg_conf_write(). This is harmless because we have a
sanity check in iwl_mvm_start_fw_dbg_conf(), but we may as well make
this unsigned and silence the underflow warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJV1FziAAoJEG4XJFUm622bEJwH/RdNlAK4+IS9Tx0K6EA2fDE3
001J16in/1IPPr8/RmQWNzHGN5/GAYlAdl5v4fkwb8qvcDCyPlQbSEC8ghd32H6M
G1101qEfGk9bhLTpI8xjeqsT1gl98LswPYNAfoRX4AJKAmNCkfJ1WILLi/Q2DUOf
oG6IersuqQOdQbkXDnMm49FBZeSkVvzsJL+WQhKhYblh0bDH3qGuLcYvtkSnt+P8
8QG5X+DPEpmaYcu+5E5N0XgffsdPj/+xXlFova4DFySDYb4OzEH1MYp/rHjPpnUo
nDJqxZIgkkmhu0CGtvpWNeSZ7GQBI0Bzdd+dwBY5yyg5AqWuQ5A1W+4r3SjvHyU=
=A8Ax
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath10k:
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
ath9k:
* add fast-xmit support
wil6210:
* implement TSO support
* support bootloader v1 and onwards
iwlwifi:
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using the out-of-line EWMA calculation, use DECLARE_EWMA()
to create static inlines. On x86/64 this results in code that's one
byte larger (for me), but reduces struct link_ant and struct link
size by the two unsigned long values that store the parameters each.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reduces code size slightly (at least on x86/64) while also
removing memory consumption by two unsigned long values for each
ath5k device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If .pull_fw_stats() fails for some reason while processing
fw stats event, collected pdev/vdev/peer stats just before
the failure should be freed. This is unlikely to happen,
just code review catch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found incorrect sequence in ath10k_core_stop() where wmi pktlog
disable cmd is passed from ath10k_debug_stop() to firmware
immediately after wmi pdev suspend cmd. Firmware will not accept
any wmi cmd after receiving wmi pdev suspend cmd.
Fix this issue in ath10k_core_stop() by moving ath10k_debug_stop()
just before sending pdev suspend cmd. So that pktlog disable cmd
will get passed before pdev suspend cmd.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9i6F
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-18' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* polish the Miracast operation
* fix a few power consumption issues
* scan cleanup
* fixes for D0i3 system state
* add paging for devices that support it
* add again the new RBD allocation model
* add more options to the firmware debug system
* add support for frag SKBs in Tx
When we enter D0i3, we must stop TXing otherwise the
sequence number we use might conflict with the firmware's
internal TX. In order to do so, we have
IWL_MVM_STATUS_IN_D0I3 which should prevent any Tx while we
enter D0i3. There is a bug in this code since we may Tx even
if IWL_MVM_STATUS_IN_D0I3 is set. This can happen as long as
mvm->d0i3_ap_sta_id is not set.
To make sure that we don't have any packet in the Tx path
while we set mvm->d0i3_ap_sta_id, call synchronize_net only
after we already set mvm->d0i3_ap_sta_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently if we wake up during D0I3 due to beacon loss we disconnect
immediately. This behaviour causes redundant disconnection, which could
be prevented by polling as it is usually done in mac80211.
Instead, we prefer reporting beacon loss and let mac80211 try polling
before disconnection.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
KASan error report:
==================================================================
BUG: KASan: out of bounds access in iwl_init_sband_channels+0x207/0x260 [iwlwifi] at addr ffff8800c2d0aac8
Read of size 4 by task modprobe/329
==================================================================
Both loops of this function compare data from the 'chan' array and then
check if the index is valid.
The 2 conditions should be inverted to avoid an out-of-bounds access.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix bug where MIMO is disabled for low latency TX on P2P VIF
regardless of configuration. Make it dependent on
IWL_MVM_RS_DISABLE_P2P_MIMO compilation option. Change configuration
so that MIMO will be disabled only in SDIO platforms.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MAC/BB name is"????" if the MAC/BB is unknown.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add diversity statistics and sync the driver
statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync the driver statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2500usb_validate_eeprom() read data up to 0x6e (EEPROM_CALIBRATE_OFFSET)
but only 0x6a bytes has been allocated and read from the eeprom.
This lead to out-of-bound accesses and invalid values for
EEPROM_BBPTUNE_R17 and EEPROM_CALIBRATE_OFFSET.
Change the EEPROM_SIZE to 0x6e in order to retrieve all the fields.
Tested with a rt2570 device.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CC [M] drivers/net/wireless/mwl8k.o
drivers/net/wireless/mwl8k.c: In function ‘mwl8k_bss_info_changed’:
drivers/net/wireless/mwl8k.c:3290:2: warning: ‘ap_mcs_rates’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(cmd->mcs_set, mcs_rates, 16);
^
drivers/net/wireless/mwl8k.c:4987:5: note: ‘ap_mcs_rates’ was declared here
u8 ap_mcs_rates[16];
^
The warning was bogus. But the conditionals were rather complicated,
with multiple redundant checks. This consolidates the checking and
makes it more readable IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I remove duplicated routines which related rtl92cu_set_hw_reg().
1. rtl92c_set_qos() and HW_VAR_AC_PARAM routine are similar code.
so i replace code with rtlpriv->cfg->ops->set_hw_reg().
2. rtl92c_set_mac_addr() and 'HW_VAR_ETHER_ADDR' case at
rtl92cu_set_hw_reg() routine are similar code.
so i removed rtl92c_set_mac_addr() function.
also it was not used anywhere.
3. remove HW_VAR_ACM_CTRL routine in rtl92cu_set_hw_reg().
if rtl_usb->acm_method is not EACMWAY2_SW, HW_VAR_ACM_CTRL is called
from HW_VAR_AC_PARAM. but it never called. because acm_method is always
EACMWAY2_SW. so i remove acm_method check routine
and HW_VAR_ACM_CTRL routine.
both usb and pci interface is not used HW_VAR_ACM_CTRL.
but i can't test pci interface module, so i didn't modify pci code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl92c_set_xxx_filter is same routine with rtl92cu_set_hw_reg.
so i remove those functions that are rtl92c_set_xxx_filter.
(rtl92c_get_xxx_filter is also same reason.)
also i add code updating struct rtl_mac member variable in the
rtl92cu_set_hw_reg.
after that, no more _update_mac_setting is not useful. thus i remove that.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' mac80211-next.git
iwlwifi needs new mac80211 patches so merge mac80211-next.git to
wireless-drivers-next.git.
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WMI 10.4 uses the same command interface as QCA988X for addba/delba
debug wmi commands. Fill wmi_10_4_ops table with the functions used
for QCA988X for these commands.
With this change, the following debugfs entries can be used to
configure the aggregation mode and to send addba request,
addba response and delba respectively in manual aggregation mode
for QCA99X0 chip.
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/aggr_mode
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba_resp
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Header format of 10.4 firmware phyerr event is not alligned
with pre 10.4 firmware. Introduce new wmi handlers to parse
10.4 firmware specific phyerror event header.
With changes covered in this patch, radar detection works on
qca9x0 hw 2.0 which uses 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
As remain is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/wil6210/wmi.c:827
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_WIL6210=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently it's not safe to install both pairwise
and groupwise keys on AP vdevs as it can cause
traffic to stop working in some multi-vif
(WPA+WEP) cases.
Fixes: ce90b27128 ("ath10k: fix multiple key static wep with ibss")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The frequency at which cycle/rx_clear counters are running might
change from one target type to another. QCA99X0 is running the
counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz.
Add a new entry to hw_params to store the target specific frequency
and use it in msecs conversion. This change fixes inconsistent
channel active/busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are three WMI_CHAN_INFO events reported per channel
in QCA99X0 firmware. First one is a notification at the begining
of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0),
second one is a notification at the end of the dwell time with cmd_flag
CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication
with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for
the channel. Since there is a new state before the completion, the handler
is to fixed so that the counts are deducted from the ones reported with
CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE.
Without this fix there will be lots of 0 msecs reported as active
and busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vif's vdev_id is used as queue number. However due
to the tx pausing design in ath10k it was possible
for a new interface to be created with its tx
queue stopped (via ieee80211_stop_queues). This
could in turn leave the interface inoperable until
ath10k_mac_tx_unlock() was called.
This problem only affected multi-vif scenarios when
new interfaces were created some time later after
other interfaces have been running for some time
and had Tx queue full at some point prior.
Possible manifestation of the bug was
authentication timeout for a client vif.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once HTT Tx queue got full offchannel queue was
stopped and never woken up again. This broke, e.g.
P2P. This could be reproduced after running a lot
of traffic enough to saturate 100% of the driver
Tx queue and then trying to send offchannel
traffic.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
wil6210:
* implement TSO support
* support bootloader v1 and onwards
Currently the driver disable power management on all low-latency
interfaces, while it should disable it on WiDi interfaces only.
Non-P2P interfaces that runs voice and video traffic should enable
power management.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS support is declared by the FW, set the bit indicating wider-BW
support as well.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The &mvm->tof_data.range_req.ap[] array has IWL_MVM_TOF_MAX_APS elements
so the check should be >= instead of >. Also the test can underflow so
I have changed "i" to unsigned.
Fixes: ce7929186a ('wlwifi: mvm: add basic Time of Flight (802.11mc FTM) support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to use hex_dump_to_buffer() in the cases like this:
hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false); /* len <= 16 */
sprintf("%s\n", outbuf);
since it maybe easily converted to simple:
sprintf("%*ph\n", len, buf);
Note: it seems in one case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.
When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' into next
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
Lmac sched scan supports partial scans, so we can set some channels to be
scanned on every scan iteration and others to be scanned only on some
iterations. Currently we set all channels to be scanned every iteration,
but still have some configuration of which iterations should be partial
and which should be full.
Remove all partial/full scan configuration to reduce confusions.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove timing values from iwl_mvm_scan_params and use defines and
arrays of values instead.
While at that fix few values and corner cases and align all OSs
to ChromeOS values.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We added calls to d3_suspend/resume trans ops during the
suspend/resume flow.
However, the wrapper code didn't verify the trans ops were
actually defined, resulting in panic when they were not
(such as in the case of sdio trans)
Fixes: 6dfb36c89d ("iwlwifi: call d3_suspend/resume in d0i3 case as well")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During hwsim_init_netlink(), we should call genl_unregister_family()
if failed on netlink_register_notifier() since the genetlink is
already registered.
Signed-off-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_orinocodev() would allocate the wiphy entry, but it would only get
registered much later in orinoco_init(). If something failed in the init
process inbetween the call to alloc_orinocodev() and the completion
of orinoco_init(), the drivers would end up calling wiphy_unregister()
with a NULL pointer causing beautiful OOPS fireworks.
Explicitly call wiphy_unregister() instead in the right places.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Our 8887 A2 chip can have separate firmware images for
bluetooth and WLAN. We observed an issue during parallel
downloading of these images by btmrvl and mwifiex drivers.
This patch claims sdio bus before starting of the firmware
download in mwifiex and releases it after completion to
fix the problem.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will check if any hidden SSID found in passive scan channels
and do specific SSID active scan for those channels.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware dump feature for SD8997 chipset.
The difference here is only one memory type is needed
to save all firmware information. Device dump information
will be uploaded to usersapace file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for 8997 chipset to mwifiex
with SDIO/PCIe/USB interface.
The corresponding firmware image files are located in:
"mrvl/sd8997_uapsta.bin"
"mrvl/pcie8997_uapsta.bin"
"mrvl/usb8997_uapsta.bin"
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code returns success if kmalloc fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this driver, two variables are masked by one quantity, and then tested
against a second number with more bits that the mask. Accordingly, the
test always fails. To minimize the possibility of such typos, a symbolic
definition of the mask is created and used.
The separate load and mask operations are also combined into a single
statement.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The drivers are converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e996db6983 (rtlwifi: rtl8192c: Add init codes for "fw_version"
and "fw_subversion") added initialization for fw_version, but failed to
note that the variable in the firmware header is little-endian. The
following Sparse warning results:
CHECK drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: warning: incorrect type in assignment (different base types)
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: expected unsigned short [unsigned] [usertype] fw_version
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: got restricted __le16 [usertype] version
When fixing this problem, I noticed that several of the drivers contain
nearly identical copies of the firmware header struct, and that only the one
used in rtl8192c{e,u} had correct endian notation. The struct has been
moved into a common header, and the other drivers will be fixed in
subsequant patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/link.c:197
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/wmi.c:331
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_drv_init.c:81
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_hst.c:171
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:277
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:206
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware peer entries are involved in internal
firmware vdev structures. This was not accounted
for and could lead firmware to crash due to asking
it to do more than it could.
Fixes: 039a0051ec ("ath10k: allocate fw resources for iface combinations")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If peer creation failed during offchannel Tx the
driver attempted to delete the peer nonetheless.
This caused the ar->num_peers counter to be
incorrectly decremented. This subsequently could
cause the counter to drop below 0 and also
eventually lead to firmware crash because host
would think there are less peer entries created in
firmware then there really were.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WoWLAN resume fails with retval 1 mac80211
will attempt to reconfig the device in a similar
manner when hw restart is requested. This wasn't
handled properly and yielded call trace warnings
and the device ended up not working.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:
(...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E
Fixes: b27bc5a40f ("ath10k: dump fw features during probing")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 1010ba4c5d ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to firmware engineers, the firmware has never required
these fields and the values have always been calculated, they were
just leftovers from a previous implementation.
Therefore remove the unnecessary calculation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ath_opmode_to_string return "OCB" for NL80211_IFTYPE_OCB. Currently
it will return "UNKNOWN".
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Add a spinlock which will ensure that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Since rx path is run in driver tasklet,
tx status cannot be reported directly from interrupt context
(there would be no way to lock it out).
Add tasklet for tx and move all possible code from irq handler
there.
Note: tx tasklet is needed because workqueue is queued very
rarely and that kills TCP performance.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx is run inside a tasklet so ieee80211_rx() should be used
instead of ieee80211_rx_ni().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DMA to variables located on the stack is a bad idea.
For simplicity and to avoid frequent allocations create
a buffer inside the device structure. Protect this
buffer with vendor_req_mutex. Don't protect vendor
requests which don't use this buffer.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit d8d2f19feb ("mwifiex: silence TDLS link delete failure
for nonexistent link") lowers the priority of error message when
TDLS link is already deleted. But it had got increased by
commit acebe8c10a ("mwifiex: change dbg print func to
mwifiex_dbg")
Reported-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Even though 'compatability' has a dedicated entry in the Wiktionary,
it's listed as 'Mispelling of compatibility'. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> for the atomic_helper.c
Signed-off-by: Jiri Kosina <jkosina@suse.com>
kbuild bot reported that commit 592fa228f2 ("ath9k: remove struct
ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 592fa228f2 ("ath9k: remove struct ath_atx_ac")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9MX3
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-04' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
For PCIe/USB chipsets, preallocated skb buffers are reused for
event handling. mwifiex_check_uap_capabilties() performs
skb_pull(). This patch adds missing skb_push() to restore skb's
data pointer/length.
This bug was introduced by commit debfc60081 ("mwifiex: update
AP WMM settings from BSS_START event")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add option to dynamically configure the fw
which debug traces to open
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preallocated event SKBs are getting reused for PCIe chipset.
Their physical addresses are shared with firmware so that
firmware can write data into them.
This patch makes sure that SKB is cleared and length is set to
default while submitting it to firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System crash was observed if one of the driver initialisation
commands is timed out. The reason is our timeout handler triggers
firmware dump, meanwhile driver initialisation error paths have
already freed the adapter structure.
Firmware hasn't yet completely initialized. So collecting firmware
dump is not needed in this case. Command timeout handler is
modified in this patch to fix the crash issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When WLAN interface is up and running, driver unload and
load was causing command timeout error.
We enable Rx data by updating RX ring read pointer in
init_fw_port(). It should be done when FW is completely
intialialised. Command timeout is fixed in this patch by
moving init_fw_port() call to mwifiex_init_fw_complete().
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable pos is u8 here, so memcpy is needed to store u16 aid.
At the same time, aid should be platform independent, upper layer
utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16
here.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC.
This patch changes the code to track active station TIDs in the txq directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setup rxfiler correctly for offchannel ctx.
This fix problem we didn't configure rxfilter, next
didn't receive probe requests and next failed
p2p_find. This was seen when ath9k loaded with
use_chanctx=1
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While mac80211 setup this per HW, set same
rxfilter configuration for all chanctx.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise p2p device support when ath9k loaded with
use_chanctx=1.
This will fix problem, when first interface is an AP
and next we would like to run p2p_find.
Before p2p find (scan phase) failed with EOPNOTSUPP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
600f5d909a54("mwifiex: cleanup ioctl wait queue and abstraction layer")
introduced the wakeup_interruptible suppression in mwifiex_complete_cmd
b1a47aa5e1e1("mwifiex: fix system hang issue in cmd timeout error case")
then added wakup_interruptible to mwifiex_cmd_timeout_func the single
place setting a status of ETIMEDOUT.
Instead of doing extra work, using the standard call-chain will have the
same effect:
mwifiex_cancel_pending_ioctl
-> mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd
-> wake_up_interruptible
The difference is that previously the condition was not set to true,
but that's probably just an oversight in b1a47aa5e1 and shouldn't
have any consequence
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in
case it already started or starts processing the cmd.
But this was probably not working the way intended:
- it is racy: mwifiex_process_cmdresp might already have passed that
test and is continuing to use the cmd node being recycled
- mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which
we just set to NULL
- mwifiex_recycle_cmd_node will clear the flag
The reason why it probably works is that mwifiex_cancel_pending_ioctl
is only called from mwifiex_cmd_timeout_func, where the there is little
chance of a command response still arriving
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_cancel_pending_ioctl is called only from
mwifiex_cmd_timeout_func. There the wait_q status is set to
-ETIMEDWAIT before calling this function. Whether we reset the status
to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both
are != 0 hence mean failure
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
standard call chain when releasing a cmd node:
mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd, if wait_q_enabled
calling mwifiex_complete_cmd explicitly and setting
wait_q_enabled = false is redundant
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 1fb654fd97ff("mmc: sdio: add reset callback to bus operations"),
sdio cards can be power cycled using mmc_hw_reset.
The use mmc_remove_host/mmc_add_host is discouraged, because these are
internal functions to the mmc core and should only be used by mmc hosts
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Boot loader versions as backward compatible,
starting from v1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Boot loader reports error starting from the struct v2.
Print error info before reset (power up state) in debug mode,
and print same info as error if target reset timed out.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for the system suspend/resume.
In preparation for the run-time PM, implementation made
run-time PM friendly: common for system and run-time PM
code factored out as generic functions, albeit is_runtime
parameter value is always false currently.
For debug purposes, "PM" debug category introduced.
Policy: AP-like interface can't be suspended; otherwise
suspend is allowed. Hardware brought down if interface
was up. Connection, if existed, get lost.
Interface will be brought up upon resume if it was up
before suspend.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow network stack part of Rx processing to run on separate core,
relaxing CPU utilization on the core used for Rx NAPI.
If RXHASH feature is enabled, the driver sets rxhash of each skb to 1
to enable RPS. The core for processing the rx skb is determined by RPS
mechanism according to rx_cpus bit mask which is configured at user level.
For processing skbs on different core from the core which processes
the interrupts, it is recommended not to enable core 0 in rx_cpus bit mask.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".
Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the recent kernel versions, multiple MSI is not well supported.
In particular, it is not supported on x86 and ARM architectures.
Also, internal interrupt handling logic is simpler and
more effective when using single interrupt.
Remove support for 3 MSI, convert module parameter
"use_msi" from int with range [0,1,3] to boolean.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx drops may be for 2 reasons: frame is old,
or it is duplicate. On the debugfs "stations" entry,
provide counters per reorder buffer for total
frames processed, drops for these 2 reasons.
Also add debug print for dropped frames.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When printing error message, provide string describing IE kind.
Derive it from IE type
This allows removing of error messages printing
in callers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sort overall IE's handling
prepare code (disabled for now) to add IEs for the beacon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW is allowed to generate WMI events that are not handled by this driver.
Treat such case as warning instead of error.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check event length;
hex dump both Rx and Tx frames
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver report supported TSO (v4 & v6) and IP checksum offload
in addition to previously supported features. In data path
skbs are checked for non-zero gso_size, and when detected sent
to additional function for processing TSO SKBs. Since HW does not
fully support TSO, additional effort is required from the driver.
Driver partitions the data into mss sized descriptors which are
then DMAed to the HW.
Signed-off-by: Vladimir Shulman <QCA_shulmanv@QCA.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading with debug_fw flag, do not bail out on
unknown chipId
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use function wil_fw_error_recovery() instead of inline equivalent code
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Multiple del_station requests may be sent to the driver by the
supplicant when turning down AP. This may overflow mailbox
between the FW and ucode
Wait till disconnect of one STA completed before sending next command.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
linux/device.h should be included using <>, not ""
since it is not local include
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the debugfs, there is "ulong" attribute printing.
It is used for bitmap printing, and more appropriate format
would be hexadecimal, not decimal.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When performing Rx reordering, count skb's dropped
per reorder buffer; and print dropped packets count
on the "stations" debugfs entry
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are 2 versions of boot loader struct: v0 and v1.
In the v1, boot loader build version added; as well as
RF status.
Support both versions.
Boot loader structure v1 has RF status; ignore RF error if firmware
not going to be loaded; driver can still be used to interact with the HW
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When building a Tx Command for management frames, we are lacking
a check for action frames, for which we should set a different
pm_timeout. This cause the fw to stay awake for 100TU after each
such frame is transmitted, resulting an excessive power consumption.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.
In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.
When the device is slave on the bus(SDIO) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. When the FW wants load / unload pages, it creates an
interrupt, and the driver uploads / downloads the page to an address in
the a specific address on the device's memory.
The driver can support up to 1 MB of pages.
Add paging mechanism for the UMAC on SDIO in order to allow the program to
use a larger virtual space while using less physical memory on the device
itself.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As a preperation for multiple RX queues change the RBD
allocation model.
The new model includes a background allocator. The allocator is
called by the interrupt handler when there are two released
buffers by the queue, and the allocator starts allocating eight
pages per request.
When the queue has released 8 pages it tries claiming the
request. If the pages are not ready - it keeps claiming.
This new model should make sure that RBDs are always available
across the multiple queues.
The RBDs are transferred between the allocator and the queue.
The queue moves the free RBDs upon freeing them to the allocator.
The allocator moves them back to the queue's possession when the
request is claimed.
The allocator has an initial pool to make sure there are always RBDs
available for the request completion.
Release of the buffers at exit is done per pools - the allocator
frees its own initial pool and the queue frees its own pool.
Existing code refactor -
-Queue's initial pool is the size of the queue only as the allocation
of the new buffers no longer uses this pool.
-Removal of replenish background work, and replenish calls in the
interrupt handler and restock().
-The replenish() and the rxq used_list are used only during
initialization.
-Moved page allocation to a new function for code reuse.
New code -
Allocator code - new structure and functions.
Interrupt handler uses the allocator functions for replenishing buffers.
Reuse of the restock() method.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Change the FW debug trigger tlv to include a monitor only
option. Setting this option to true will cause fw dump triggers
to only collect monitor data and skip other dumps such as
SMEM, SRAM, CSR, PRPH, etc.
This option is used when accessing the different parts of the
firmware memory is not wanted and can cause unwanted behavior
like when debugging TX latency.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow frag SKBs in PCIe and advertise the maximum number of frags
to the opmode. As a fallback. linearize the SKB if it exceeds the
maximum number of fragments. This allows using the hardware better
(filling more TBs) and should improve performance when used by the
opmode.
Also adjust tracing to be able to deal with this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Gscan is a scan feature which is supported on certain devices only,
hence the need for a TLV flag for it. For devices that support gscan
store the gscan capabilities advertised by the FW so the driver can
report it to upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set max TX aggregation size for 8260 SDIO devices series to 40 frames.
Fine tune max RX aggregation size - change it to 21.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our firmware scheduler used to suffer from false wake-up on 500 time units.
We had to came up with a formula to address this buggy behavior.
Now that our firmware is fixed, we can go back to our old policy.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for dumping all the RBs in the RX queue
when FW error occurs.
This will assist debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Print the CPU1 and CPU2 secured boot status registers from the NIC
to indicate a SYSASSERT during secured engine unlocking process
on init/protocol image.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.
In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.
When the device is master on the bus(PCI) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. The FW can load / unload the pages on its own.
The driver can support up to 1 MB of pages.
Add paging mechanism for the UMAC on PCI in order to allow the program
to use a larger virtual space while using less physical memory on the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended command id in triggers handling.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended firmware event header that contains
a group id as well as the command id.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add support for extended command id in notification system.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes various functions in the file rs.c void due to these
functions never returning a error code to signal to their callers
if and how they have failed to complete their intended work.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move the TX PN assignment (for CCMP only) to the driver. This prepares
the driver for future DSO (driver segmentation offload) where it will
split an SKB into multiple MPDUs by itself.
For TDLS, split out the CCMP TX command handling so that it won't get
a PN assigned, the firmware assigns the PN in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the CSR_DRAM_INIT_TBL_WRITE_POINTER bit wasn't set
on ict reset, in some flows (like disable ict followed by
immediate reset ict) the driver and hardware went out
of sync (the driver cleared the ict_index, while the hw
kept it intact).
Fix it by setting the flag when resetting ict.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).
Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.
After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CQM overwrites a few thresholds in the bf command. On the other hand,
when entering D0i3 the thresholds are set to higher values on purpose,
so ignore CQM in this case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The slow filtering threshold should be higher in D0i3 case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TCP software implementation on the host requires extensive computing
power. Offloading even some of the TCP/IP stack to the NIC might save
a significant overhead. In order to enable this feature on our hw,
we need to configure it first. Once done, we mark this capability,
to be advertised later to the OS via ieee80211_register_hw.
The driver Rx indications for TCP Checksum is integrated within the
standard Rx status. The driver responds to those indications as follows:
If the frame was tested by hw and checksum ok report CHECKSUM_UNNECESSARY.
Otherwise, report CHECKSUM_NONE.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware debug infrastructure allows the user to
provide a firmware that will toggle a few registers to
configure the debugging capabilities.
On certain devices, certain operations are forbidden.
Executing a forbidden operation will cause the hardware to
die in a way that only driver unload / load will bring it
back to life.
Fortunately, there is a way to know in advance if those
operations will be accepted by the device. This is where
the new PRPH_BLOCKBIT operation plays its role. If the bit
X from PRPH register Y is set, then we should prevent any
further register configuration. When that happens, drop a
line in the kernel log since this is really an error state:
the user won't have his device configured as he expected.
Add operations that will be used in the future:
INDIRECT_ASSIGN, INDIRECT_SETBIT, and INDIRECT_CLEARBIT.
Other debugging configurations (such as destination
configuration for the monitor) will take place in any case.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
use the AP station for multicast frames instead of the auxiliary
station as otherwise the frames can be sent to an absent P2P GO as
the FW does not block transmissions for the auxiliary station
since it is not associated with the station MAC context.
Note that this is not possible for unicast frames, as a TDLS
discovery response is sent without a station entry, and in this
case the P2P GO NoA should not block transmission to the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow the transport layer to return an error upon suspend.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This reverts commit 088070a2f6.
When working in d0i3_on_idle mode, we explicitly go out
of d0i3 on resume (so other potential commands could
be sent).
However, D0I3_DEFER_WAKEUP is currently cleared on
resume complete (which happens only later on), causing
d0i3 exit to timeout.
Since mac80211 was modified to accept incoming frames
once drv_resume was called, we can safely revert this
patch, and handle the pending work on iwl_mvm_resume().
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Existing UMAC commands already use the long header, but are sent
with group 0 and the long header inserted manually. Move them to
the group 1 to take advantage of the header building in the low-
level transport.
Existing firmware ignores the group_id field (it's reserved) and
the first firmware that really supports long command headers can
parse all commands in both group 0 (with short header) and group
1 (with long header.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As the firmware is slowly running out of command IDs and grouping of
commands is desirable anyway, the firmware is extending the command
header from 4 bytes to 8 bytes to introduce a group (in place of the
former flags field, since that's always 0 on commands and thus can
be easily used to distinguish between the two.
In order to support this most easily in the driver widen the command
command ID used in the command sending functions and encode the new
values (group and version) in the ID. That way existing code doesn't
have to be changed (since the higher bits are 0 automatically) and
newer code can easily use the new ID generation function to create a
value to use in place of just the command ID.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ToF is a time based method for measurement of the WiFi device
location within a WiFi environment. The driver functionality provided
by this patch is the interface for communication with FW and receiving
location related updates from the FW. The interface provided by this
patch is via debugfs.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares support this API.
This includes removing dwell per band, as band is no longer a factor
in calculating the dwell. Only basic dwell is used and FW will calculate
the actual dwell time.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 'flags' field really has been reserved in the firmware API for a
very long time, probably since 4965. As a consequence, the field is
always 0 and checking for a IWL_CMD_FAILED_MSK flag makes no sense.
Rename the field to 'reserved', get rid of IWL_CMD_FAILED_MSK and
all the code for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In iwlmvm firmwares, the Byte count written in the scheduler
byte count table is in DWORDs and not in bytes.
We should check that this value fits in the 12 bits and
the value can be either in bits of in DWORD or bytes
depending on the firmware. Check the value after the
translation to DWORDs is done (if needed).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In a few places, we were disabling interrupts but didn't
make sure that the interrupt handler has finished running.
Add calls to synchronize_irq() to ensure we finish handling
the interrupts before we free resources or other things that
could lead to a crash if the interrupt were to be handled
later.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the firmware crashes, we can't expect the Tx queues to
progress. Cancel their timer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the time-event is sent with the immediate flag set, there is
no need to sample the device time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
With the previous patch series, no opmode continues using the
command or handler_status (i.e. the return value from the RX)
so it can be removed now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the mvm driver, neither the old command nor the return value
are used, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the previous patches, the command that's passed in nor the
return value are used any more, so can be removed.
While at it, make some functions static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This makes the logging a little less useful, but as they're mostly
synchronous commands it won't matter much. It gets rid of the
dependency on the input command, which this is the only user of.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This driver currently has some very confusing ADD_STA response handling
that runs asynchronously in the background for all of the commands, but
is only really necessary for synchronous ones (the really asynchronous
ones can only be done for already existing stations), and for the sync
ones it actually waits for the RX handler to return a status code.
Rework this to keep the debug printing in the handler, but do the code
that's supposed to have an effect only for sync commands in the command
sending function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current key offset assignment algorithm always uses the lowest
unused key offset, which will potentially lead to issues when the
firmware will change to take the key material for TX from the key
table rather than from the TX command.
In order to avoid those issues (and avoid forgetting about them)
change the key offset allocation algorithm now to avoid reusing key
offsets quickly.
The new algorithm always picks as the next offset the least recently
freed offset, i.e. the offset that has been unused for the longest
amount of time. This is implemented by having a generation counter
for each key offset that is incremented every time a key is deleted,
except for the one that's deleted, which is reset to zero. Thus the
highest counter is the key that's been unused longest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During NIC initialization shared HW is reset and this disables the
scheduler. Some HW platforms do not activate the scheduler after it.
Consequently all HCMD sent by the driver stay at the queues which cause
to queue stuck.
Set the scheduler to work on auto active mode so it would be activated upon
change over one of the queues' write pointer.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver code allows for the disabling of MSI interrupts; however the
module_parm line was missed and the option fails to show with modinfo.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.15+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVu222AAoJEG4XJFUm622biQIH/1A5WVvXw1WbxbnKh3xJmLSZ
OkuSORBl0rbzf0CTtxDax59JqjZaCUZ2MdehKiCFQsv7DKuYk3JnkkvIhSkuTcpX
k4x5CbTIY0MuERtvtsoH+A4hi571jqYprtECRDCZiyDkhNyEnKpKA+ImPXa8HMeQ
iXny9IsH//jtsgcorM2bNcV6QmeUjUozU1jbcRk1pOLd6755ntmI4dRgR0vEpolt
UUEjPEStiaxovXF+dIpEaaANpTggspjku+lFJ1mH6IIyCZMLsnQ3+V/mlFxnPKAA
xFneaOkDYdQYyBAjG7yrPaWWg705Oraamfl2W5a665cOqbfAsUZ+9H0AbHOzSYI=
=99A8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6301566e0b. Oleksij Rempel
noticed that the randomness doesn't look to be good enough and Stephan Mueller
commented:
"I would say that the discussed RNG does not seem fit for hooking it up with the
hwrandom framework."
http://lkml.kernel.org/g/3945775.m5HblJPgiO@tauon.atsec.com
So let's the revert the patch until we are sure that we can trust this random
generator.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 33511b157b ("rtlwifi: add support to
send beacon frame"), the mechanism for sending beacons was established. That
patch works correctly for rtl8192cu, but there is a possibility of getting
the following warnings in the PCI drivers:
WARNING: CPU: 1 PID: 2439 at net/mac80211/driver-ops.h:12
ieee80211_bss_info_change_notify+0x179/0x1d0 [mac80211]()
wlp5s0: Failed check-sdata-in-driver check, flags: 0x0
The warning is followed by a NULL pointer dereference as follows:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000006
IP: [<ffffffffc073998e>] rtl_get_tcb_desc+0x5e/0x760 [rtlwifi]
This problem was reported at http://thread.gmane.org/gmane.linux.kernel.wireless.general/138645,
but no solution was found at that time.
The problem was also reported at https://bugzilla.kernel.org/show_bug.cgi?id=9744
and this solution was developed and tested there.
The USB driver works with a NULL final argument in the adapter_tx() callback;
however, the PCI drivers need a struct rtl_tcb_desc in that position.
Fixes: 33511b157b ("rtlwifi: add support to send beacon frame.")
Signed-off-by: Luis Felipe Dominguez Vega <lfdominguez@nauta.cu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.19+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On the 2GHz and and on the 5GHZ band only the extpa_gain setting from
the 5GHz band was checked. this patch makes it check the property from
the correct band.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes commit eae79b4f3e ("rsi: fix memory leak in rsi_load_ta_instructions()")
which stopped the driver from functioning.
Firmware data has been allocated using vmalloc(), resulting in memory
that cannot be used for DMA. Hence the firmware was first copied to a
buffer allocated with kmalloc() in the original code. This patch reverts
the commit and only calls "kfree()" to release the buffer after sending
the data. This fixes the memory leak without breaking the driver.
Add a comment to the kmemdup() calls to explain why this is done, and abort
if memory allocation fails.
Tested on a Topic Miami-Florida board which contains the rsi SDIO chip.
Also added the same kfree() call to the USB glue driver. This was not
tested on actual hardware though, as I only have the SDIO version.
Fixes: eae79b4f3e ("rsi: fix memory leak in rsi_load_ta_instructions()")
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
noisy false alarms.
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems.
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gMW5
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-07-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* a fix for the stuck TFD queue mechanism - it was producing
noisy false alarms.
* a fix for the NIC prepare flow that prevented the driver
from being able to access the device on certain systems.
* a fix for the scan prority handling which allows the
regular scan to run even if a scheduled scan is already
running.
The stuck queue detection mechanism allows to detect queues
that are stuck. For sleeping clients, a queue may rightfully
be stuck: if a poor client implementation stays asleep for
more than 10s, then we don't want to trigger recovery flows
because of that client.
In order to cope with this, I added a mechanism that
monitors the state of the client: when a client goes to
sleep, the timer of his queues is frozen. When he wakes up,
the timer is reset to the right value so that if a client
was awake for more than 10s and the queues are stuck, only
then, the recovery flow will kick in.
This is valid only on non-shared queues: A-MPDU queues.
There was a bug in case we Tx to a sleeping client that has
an empty A-MPDU queue: the timer was armed to now + 10s.
This is bad, but pretty harmless.
The problem is that when the client wakes up, the timer is
modified to be now + remainder. But remainder is 0 since the
queue was empty when that client went to sleep...
Fix this by checking the state of the client before playing
with the timer when we add a packet to an empty queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initial QCA99X0 support has a known issue with TCP Tx throughput.
All other path such as UDP Tx/Rx and TCP Rx meet their expectation
(> 900Mbps), but TCP Tx marked as low as 5Mbps when single pair is
used on iperf.
The root cause is turned out because TSO flag is not initialized
properly so that firmware configures TSO in wrong way.
TSO flags in msdu extension descriptor is required to be reset
to indicate firmware there is no TSO is enabled, otherwise it
could act as TSO is enabled which causes huge throughput drop.
In fact, it's enough by resetting TSO flags only to prevent the
unexpected behavior, but initializing whole msdu ext. descriptor
will help to clear uncertainty of firmware could bring on as it
constantly updated.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.
kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.
Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@tieto.com>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During tx completion, tx_lock is held for longer than required, preventing
efficient refill of htt->pending_tx. Refactor the code so that only MSDU
related operations are protected by the lock.
Improves downstream performance on a dual-core ARM Freescale LS1024A
(f.k.a. Mindspeed Comcerto 2000) AP with a 3x3 client from 495 to 580 Mbps.
Other CPU bound multicore systems may also benefit.
Signed-off-by: Denton Gentry <dgentry@google.com>
Signed-off-by: Avery Pennarun <apenwarr@google.com>
[mfaltesek@google.com: removed conflicting code for tracking msdu_ids.]
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
