Move the (DDR) SDRAM controller headers to include/soc/at91 to remove the
dependency on mach/ headers from the at91-reset driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In the case of at91sam9g45_restart(), the driver is writing
AT91_DDRSDRC_LPCB_POWER_DOWN to AT91_DDRSDRC_RTR, this should actually be
AT91_DDRSDRC_LPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cP1w
-----END PGP SIGNATURE-----
Merge tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull restart handler infrastructure from Guenter Roeck:
"This series was supposed to be pulled through various trees using it,
and I did not plan to send a separate pull request. As it turns out,
the pinctrl tree did not merge with it, is now upstream, and uses it,
meaning there are now build failures.
Please pull this series directly to fix those build failures"
* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
arm/arm64: unexport restart handlers
watchdog: sunxi: register restart handler with kernel restart handler
watchdog: alim7101: register restart handler with kernel restart handler
watchdog: moxart: register restart handler with kernel restart handler
arm: support restart through restart handler call chain
arm64: support restart through restart handler call chain
power/restart: call machine_restart instead of arm_pm_restart
kernel: add support for kernel restart handler call chain
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
Fix
drivers/power/ab8500_fg.c: In function 'ab8500_fg_probe':
drivers/power/ab8500_fg.c:2989:27:
warning: 'i' may be used uninitialized in this function
drivers/power/ab8500_fg.c:2972:15: note: 'i' was declared here
which actually points to a real bug.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch is to fix some bugs in reboot driver. Which includes auto selection
of the MFD_SYSCON for the driver, use of container to locate restart handler,
correction of the count down failure timer and ordering of the header file.
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[ sre: return err instead of 0 in syscon_reboot_probe() ]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fix the following issues.
- Flag for bq27742 is 2 bytes contracy to 1 byte for older hardware
- Don't read FLAG_CI as bq27742 does not have it
- Use Battery full capacity register as last measure discharge
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This change replaces use of arm_pm_restart with recently introduced
reset mechanism in Linux kernel called restart_notifier.
Choosing priority 128, which is default priority, as according to
documentation, this mechanism is sufficient to restart the entire system.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This driver registers a restart handler to set a GPIO line high/low
to reset a board based on devicetree bindings.
Signed-off-by: David Riley <davidriley@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This driver adds the restart functionality for STiH415 and STiH416
platforms from STMicroelectronics. This driver registers an
arm_pm_restart function to reset the platform.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
machine_restart is supported on non-ARM platforms, and and ultimately
calls arm_pm_restart, so dont call arm_pm_restart directly but use the
more generic function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This driver enabled us to drive the reboot of the Versatile family
of ARM reference boards. Even though only the RealView boards are
supported initially, these boards all have the same procedure for
reboot:
- Write a magic value into an unlocking register
- Write another magic value into a reset control register
The driver will be reusable for Versatile and possibly also the
Integrator family of reference boards.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
IO domain voltages on some Rockchip SoCs are variable but need to be
kept in sync between the regulators and the SoC using a special
register.
A specific example using rk3288:
- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to
that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1.
Said another way, this driver simply handles keeping bits in the SoC's
general register file (GRF) in sync with the actual value of a voltage
hooked up to the pins.
Note that this driver specifically doesn't include:
- any logic for deciding what voltage we should set regulators to
- any logic for deciding whether regulators (or internal SoC blocks)
should have power or not have power
If there were some other software that had the smarts of making
decisions about regulators, it would work in conjunction with this
driver. When that other software adjusted a regulator's voltage then
this driver would handle telling the SoC about it. A good example is
vqmmc for SD. In that case the dw_mmc driver simply is told about a
regulator. It changes the regulator between 3.3V and 1.8V at the
right time. This driver notices the change and makes sure that the
SoC is on the same page.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman: fix compiler warnings]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Make the max14577 charger driver depending on SYSFS instead selecting
it. This fixes warning on x86_64 with allmodconfig:
scripts/kconfig/conf --allmodconfig Kconfig
fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1: symbol SYSFS is selected by CHARGER_MAX14577
drivers/power/Kconfig:327: symbol CHARGER_MAX14577 depends on POWER_SUPPLY
drivers/power/Kconfig:1: symbol POWER_SUPPLY is selected by HID_SONY
drivers/hid/Kconfig:638: symbol HID_SONY depends on NEW_LEDS
drivers/leds/Kconfig:8: symbol NEW_LEDS is selected by SENSORS_APPLESMC
drivers/hwmon/Kconfig:299: symbol SENSORS_APPLESMC depends on HWMON
drivers/hwmon/Kconfig:5: symbol HWMON is selected by EEEPC_LAPTOP
drivers/platform/x86/Kconfig:496: symbol EEEPC_LAPTOP depends on HOTPLUG_PCI
drivers/pci/hotplug/Kconfig:5: symbol HOTPLUG_PCI depends on SYSFS
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Some gpio implementations return interesting values for gpio_get_value when
the value is not 0 - as seen on a imx6sl board. Therefore do not use the
value returned from gpio_get_value directly but simply check for 0 or not 0.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use of_get_child_by_name to obtain reference to charger node instead of
of_find_node_by_name which can walk outside of the parent node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Check the return value of devm_kzalloc() to fix possible NULL pointer
dereference and properly exit the probe() on memory allocation failure.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support to bq27742 in bq27x00 driver. bq27742 register
addresses are mostly mostly the same as bq27500 addresses
with minor differences.
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
MAX77836 has the same Fuel Gauge as MAX17040/17048. The max17040 driver
can be safely re-used. The patch adds MAX77836 device to the array of
i2c_device_id. Additionally it removes the id associated with MAX17040
device as the value is not used.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove hard-coded values for:
- Fast Charge current,
- End Of Charge current,
- Fast Charge timer,
- Overvoltage Protection Threshold,
- Battery Constant Voltage,
and use DTS or sysfs to configure them. This allows using the max14577 charger
driver with different batteries.
Now the charger driver requires valid configuration data from DTS. In
case of wrong configuration data it fails during probe.
The fast charge timer is configured through sysfs entry.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 charger to the max14577 driver. The MAX77836
charger is almost the same as 14577 model except:
- No dead-battery detection;
- Support for special charger (like in MAX77693);
- Support for DX over-voltage protection (like in MAX77693);
- Lower values of charging current (two times lower current for
slow/fast charge, much lower EOC current);
- Slightly different values in ChgTyp field of STATUS2 register. On
MAX14577 0x6 is reserved and 0x7 dead battery. On the MAX77836 the
0x6 means special charger and 0x7 is reserved. Regardless of these
differences the driver maps them to one enum max14577_muic_charger_type.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a driver for the LTC2952, an external power control chip,
which signals the OS to shut down. Additionally this driver lets the
kernel power down the board.
Signed-off-by: René Moll <rene.moll@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This piece of code was added so that we return -EPROBE_DEFER when no devices are
registered. But even if class_for_each_device() returns 0, we are going to
return -EPROBE_DEFER only.
And so this code isn't required at all. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Using 'goto' statements for freeing resources on failures is a good choice as it
makes code very clean, and reduces the chances of human errors.
Though in most cases compiler may take care of this. But adding unnecessary
'goto' statements wouldn't make anything better. Code becomes less readable
actually.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In power_supply_show_property() routine, we call ->get_property() conditionally
and should check for failure in that case only. There is no point comparing
'ret' for errors when 'ret' is surely zero.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
At multiple places we are doing exactly what PTR_ERR_OR_ZERO() does. And so that
routine can be reused instead of increasing lines of code here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The 'if' statements in power_supply_changed_work() are mostly there for taking
care of races and normally they will always evaluate to true. Optimize them for
fast execution with 'likely' statements.
Also there is need to have better comments in code to mention about the races
clearly. Get them in place.
Cc: Zoran Markovic <zrn.markovic@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
There is no need to check the value of ret.intval before returning it, as we
will be returning zero explicitly when ret.intval is zero.
So essentially we will end up returning value of ret.intval as it is. Drop the
unnecessary 'if' statements.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We need to stop 'class_for_each_device' loop when a supply matches with the
of-node. In order to achieve this we currently return -EINVAL from
__power_supply_populate_supplied_from() on successful match.
class_for_each_device() is free to return similar errors in other cases as well
and so the choice of return value here isn't particularly great.
This commit isn't removing the Hack but making it more elegant by returning '1'
instead.
Also power_supply_find_supply_from_node() can return errors other than
-EPROBE_DEFER now if class_for_each_device() fails.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Callers of power_supply_find_supply_from_node(), i.e.
power_supply_check_supplies(), must propagate the errors returned by it instead
of returning their own.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
of_node_put() was called twice in power_supply_check_supplies() whereas a single
call will also work. Rearrange code a bit to make that feasible.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In few routines, we need to end the do-while loop when no more "power-supplies"
are available. Currently we are doing 'continue' which will make the
'while(np)' conditional statement run again.
Skip this by doing a 'break' instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Typecast from 'void *' to any other pointer type falls under implicit typecasts
category and so doesn't require explicit typecasts. Drop them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If power-supply's DT node doesn't have a valid "power-supplies" entry, then
power_supply_check_supplies() should return early instead of trying to allocate
memory for "supplied_from" array.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In routine power_supply_check_supplies(), 'cnt' is counting the number of
supplies passed in "power-supplies" field of a node. The value of 'cnt' will
always be one more than the number of supplies after the do-while loop ends. And
so we need to allocate memory for 'cnt - 1' char pointers. But we are allocating
memory for 'cnt' instead.
Fix this by not over-allocating memory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Usually PMIC's come with coulomb counting mechanism which can be
used to implement a Fuel Gauginig solution in Software itself.
One of key input to these SW Fuel Gauge solutioons is the boot up
parameters like boot voltage and boot current.
This patch adds the VOLTAGE_BOOT and CURRENT_BOOT power supply attributes
to report bootup voltage and current.
This patch also adds CALIBRATE power supply attribute which useful is
for calibrating the battery/coulomb counter.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch check the charging state after completed initialization of charger-
manager and update current charging state. If charger-manager never check and
update current charging state, charger-manager would have the mismatch issue
between real state of cable connection and the charging state of charger-manager
until first polling time of charger-manager.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch fix minor issue about checking wrong return type.
The of_cm_parse_desc() return ERR_PTR(errnor number) when some error happen
in this function. But, charger_manager_probe() has only checked whether
desc is NULL or not. If of_cm_parse_desc() returns ERR_PTR(-ENOMEM), desc
isn't NULL but desc is (void *)(-ENOMEM). Althouhg some error happen for parsing
DT, charger_manager_probe() can't detect error of desc instance.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The xgene-reset driver uses xgene_restart() as arm_pm_restart() but that
function should take an enum reset_type as the first argument rather than
a char. Fix this; the paramter is not referenced in the implementation.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
sbs-battery has a max design voltage but not a min design voltage field.
The SBS spec only has one design voltage:
http://www.sbs-forum.org/specs/sbdat110.pdf
Currently this is being used for max design voltage. This patch uses it
for min design voltage as well.
Signed-off-by: Simon Que <sque@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This CL supports two power_supply_property items for smart battery:
POWER_SUPPLY_PROP_MANUFACTURER and POWER_SUPPLY_PROP_MODEL_NAME such
that battery information 'manufacturer' and 'model_name' can be exported
to sysfs.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The wakeup status is read from Shutdown Status Register and not the
SHDW_CR which is the one at address 0.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
MACH_AT91 doesn't exist so we can't "depend" on it. Fix the typo
by using the proper ARCH_AT91 config option.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YBPz
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux
Pull AT91 reset, poweroff and ram drivers from Maxime Ripard:
"This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled."
Conflicts:
arch/arm/mach-at91/Kconfig
