* R-Car Gen3 boards and SoCs
- Make phy-mode of EtherAVB a board-specific property.
The SoC DTs file now uses "rgmii" and boards override this with
"rgmii-txid" as appropriate. Previously "rgmii-txid" was used
in SoC DTs but this did not describe that more sophiticated
functionality is a board rather than SoC property.
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* R-Car D3 (r8a77995)
- Add I2C nodes and then describing the PCA9654 I/O expander connected to
the I2C0 bus.
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable PFC support for configuring SCIF0 pins
This uses PFC support added to the V3M DT
- Describe EtherAVB PHY IRQ
This uses support for GPIO added to the V3M DT
- Enable I2C0 support
Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
we're only describing the former chip now)."
* R-Car V3M (r8a77970) SoCs
- Add PFC support
- Describe GPIO devices
- Describe I2C devices
- Srt subnodes of root node alphabetically to eas future maintence overhead
* Draak board with R-Car D3 (r8a77995) SoC
- Enable SDHI2
Wolfram Sang says "The single SDHI controller is connected to eMMC."
- Enable DU
Kieran Bingham says "Enable the DU, providing only the VGA output for
now."
* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
- Move nodes which have no reg property out of bus
By deffinition the bus only has hardware with an address on the bus
- Remove non-existing STBE region from EtherAVB
Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
* R-Car D3 (r8a77995) SoC
- Add FCPV, VSP and DU support
Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
One VSPBS can be used as a dual-input image blender, while two VSPD
instances can be utilised as part of a display (DU) pipeline.
Add support for these, along with their required FCPV nodes."
* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
- Add GPIO extender
This is a basis for follow-up work to configure the GPIOs of the extender
* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
- Initial upstream support
* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Add OPPs table for cpu devices
This, along with recently upstreamed Z and Z2 clock support allows
use of CPUFreq with both A57 and A53 CPUs.
- Add thermal cooling management
Allows the use of CPUFreq as a cooling device on A57 CPUs
- Correct register size of thermal node
Niklas Söderlund says "To be able to read fused calibration values from
hardware the size of the register resource of TSC1 needs to be
incremented to cover one more register which holds the information if
the calibration values have been fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry"
- Fix register mappings on VSPs
Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
register space is mapped correctly to support this."
* R-Car H3 (r8a7795) SoC
- Move SCIF node into alphabetical order to ease future maintenance overhead
- Add IPMMU-PV1 device node
This resolves an oversight when IPMMU nodes were added to the H3 DT.
All IPMMU devices should now be described in DT.
- Add missing SYS-DMAC2 dmas
Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
can make use of DMA are wired to either SYS-DMAC0 only, or to both
SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has
been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
2016)."
-----BEGIN PGP SIGNATURE-----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=wu1f
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM64 Based SoC DT Updates for v4.17" from Simon Horman:
* R-Car Gen3 boards and SoCs
- Make phy-mode of EtherAVB a board-specific property.
The SoC DTs file now uses "rgmii" and boards override this with
"rgmii-txid" as appropriate. Previously "rgmii-txid" was used
in SoC DTs but this did not describe that more sophiticated
functionality is a board rather than SoC property.
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* Condor board with R-Car V3H (r8a77980) SoC
- Initial upstream support
* R-Car D3 (r8a77995)
- Add I2C nodes and then describing the PCA9654 I/O expander connected to
the I2C0 bus.
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable PFC support for configuring SCIF0 pins
This uses PFC support added to the V3M DT
- Describe EtherAVB PHY IRQ
This uses support for GPIO added to the V3M DT
- Enable I2C0 support
Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor
PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but
we're only describing the former chip now)."
* R-Car V3M (r8a77970) SoCs
- Add PFC support
- Describe GPIO devices
- Describe I2C devices
- Srt subnodes of root node alphabetically to eas future maintence overhead
* Draak board with R-Car D3 (r8a77995) SoC
- Enable SDHI2
Wolfram Sang says "The single SDHI controller is connected to eMMC."
- Enable DU
Kieran Bingham says "Enable the DU, providing only the VGA output for
now."
* R-Car D3 (r8a77995) and V3M (r8a77970) SoCs
- Move nodes which have no reg property out of bus
By deffinition the bus only has hardware with an address on the bus
- Remove non-existing STBE region from EtherAVB
Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs
* R-Car D3 (r8a77995) SoC
- Add FCPV, VSP and DU support
Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances.
One VSPBS can be used as a dual-input image blender, while two VSPD
instances can be utilised as part of a display (DU) pipeline.
Add support for these, along with their required FCPV nodes."
* Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs
- Add GPIO extender
This is a basis for follow-up work to configure the GPIOs of the extender
* Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC
- Initial upstream support
* R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Add OPPs table for cpu devices
This, along with recently upstreamed Z and Z2 clock support allows
use of CPUFreq with both A57 and A53 CPUs.
- Add thermal cooling management
Allows the use of CPUFreq as a cooling device on A57 CPUs
- Correct register size of thermal node
Niklas Söderlund says "To be able to read fused calibration values from
hardware the size of the register resource of TSC1 needs to be
incremented to cover one more register which holds the information if
the calibration values have been fused or not.
Instead of increasing TSC1 size to the value from the datasheet update
all TSC's size to the smallest granularity of the address decoder
circuitry"
- Fix register mappings on VSPs
Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the
register space is mapped correctly to support this."
* R-Car H3 (r8a7795) SoC
- Move SCIF node into alphabetical order to ease future maintenance overhead
- Add IPMMU-PV1 device node
This resolves an oversight when IPMMU nodes were added to the H3 DT.
All IPMMU devices should now be described in DT.
- Add missing SYS-DMAC2 dmas
Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that
can make use of DMA are wired to either SYS-DMAC0 only, or to both
SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has
been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25,
2016)."
* tag 'renesas-arm64-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
arm64: dts: renesas: v3msk: add SCIF0 pins
arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas
arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node
arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically
arm64: dts: renesas: eagle: add I2C0 support
arm64: dts: renesas: r8a77970: add I2C support
arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header
arm64: dts: renesas: r8a77965: Add EtherAVB device node
arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"
arm64: dts: renesas: v3msk: Override EtherAVB phy-mode
arm64: dts: renesas: eagle: Override EtherAVB phy-mode
arm64: dts: renesas: draak: Override EtherAVB phy-mode
arm64: dts: renesas: ulcb: Override EtherAVB phy-mode
arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode
arm64: dts: renesas: r8a77965: Add INTC-EX device node
arm64: dts: renesas: r8a77965: Add IIC-DVFS device node
arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N
...
Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.
-----BEGIN PGP SIGNATURE-----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=u8uZ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "arm64: tegra: Device tree changes for v4.17-rc1" from Thierry Reding:
Adds initial support for the P2972-0000 development board based on
Tegra194 and enables the AHCI controller on Jetson TX1.
* tag 'tegra-for-4.17-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable AHCI on Jetson TX1
arm64: tegra: Add SATA node for Tegra210
arm64: tegra: Add device tree for the Tegra194 P2972-0000 board
arm64: tegra: Add Tegra194 chip device tree
Pull "Freescale arm64 device tree updates for 4.17" from Shawn Guo:
- Move cpu_thermal device out of bus node to fix DTC simple_bus_reg
warning seen with W=1 switch.
- Fix IFC child nodes' unit-address to eliminate DTC simple_bus_reg
warnings.
- Add a dummy size memory 'reg' property for LS1046A device tree to
avoid unit_address_vs_reg DTC warning, and the real size will be
filled by bootloader.
- Update ls208xa-qds board device tree to fix unit_address_vs_reg
warnings with DSPI device.
- Add idle-states for LS1012A and LS1043A, and correct
arm,psci-suspend-param setting for already added idle-states.
- DPAA QBMan portal and watchdog device addition.
* tag 'imx-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: ifc: Fix the unit address format in the examples
arm64: dts: ls1046a: add a dummy memory 'reg' property
arm64: dts: fsl: fix ifc simple-bus unit address format warnings
arm64: dts: fsl: update the cpu idle node
arm64: dts: ls1043a: add cpu idle support
arm64: dts: ls1012a: add cpu idle support
arm64: dts: ls208xa-qds: Fix the 'reg' property
arm64: dts: ls208xa-qds: Pass unit name to dspi child nodes
arm64: dts: ls208xa: Move cpu_thermal out of bus node
arm64: dts: ls1088a: Move cpu_thermal out of bus node
arm64: dts: ls1046a: Move cpu_thermal out of bus node
arm64: dts: ls1043a: Move cpu_thermal out of bus node
arm64: dts: ls1012a: Move cpu_thermal out of bus node
arm64: dts: Add DPAA QBMan portal 9
arm64: dts: ls1088a: add DT node of watchdog
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds regulators that have fixed voltage for audio codec
on UniPhier LD11/20 Global boards. This patch fixes warnings about
TAS57xx audio codec such as "tas571x 0-001b: 0-001b supply AVDD
not found, using dummy regulator".
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of the AVE ethernet controller for LD11 and LD20 SoCs
and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds compress audio node for S/PDIF on UniPhier LD11/20
global boards. And adds settings of AIO for it.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds codec node for TI TAS571x on UniPhier LD11/20
global boards. And adds settings of AIO for speaker out.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable AHCI on Jetson TX1 and add sata phy node.
Signed-off-by: Preetham Chandru R <pchandru@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the (previously omitted) SCIF0 pin data to the V3M Starter Kit board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On R-Car H3, on-chip peripheral modules that can make use of DMA are
wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2.
Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2],
SCIF[0125], and I2C[0-2]. These were initially left out because early
firmware versions prohibited using SYS-DMAC2. This restriction has been
lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7795 IPMMU-PV1 and keep it disabled by default.
This device is not present in r8a7795 ES1.x and
is removed from the DT of those SoCs.
This corrects an omission in
3b7e7848f0 ("arm64: dts: renesas: r8a7795: Add IPMMU device nodes")
This does not have any runtime effect.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Sort root sub-nodes alphabetically for allow for easier maintenance of
this file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Eagle board dependent part of the I2C0 device node.
The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and
Analog Devices ADV7511W HDMI transmitter (but we're only describing the
former chip now).
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A77970 parts of the I2C[0-4] device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the V3MSK board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii"
mode and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Eagle board provides TX and RX
channels delays, make the "phy-mode" property a board-specific one,
meant to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77970 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Draak board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a77995 SoC DTSI to use "rgmii" mode
and let the board file override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96/965 SoC DTSI to use "rgmii"
mode and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the Interrupt Controller for External
Devices (INTC-EX) on R-Car M3-N, which serves external IRQ pins
IRQ[0-5].
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Populate the device node for the IIC Bus Interface for DVFS (IIC for
DVFS) on R-Car M3-N, and add an alias to fix its bus number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-N SiP.
Most features are enabled through the shared salvator-xs.dtsi board
description. The memory configuration is specific to the M3-N SiP.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Switch to SPDX-License-Identifier, update patch description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#interrupt-cells" property and "interrupt-controller" label to
"interrupt-controller@e61c0000" device node.
This silences the following DTC compiler warnings:
Warning (interrupts_property): Missing interrupt-controller or
interrupt-map property in /soc/interrupt-controller@e61c0000
Warning (interrupts_property): Missing #interrupt-cells in
interrupt-parent /soc/interrupt-controller@e61c000
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#pwm-cells" property to "pwm@e6e31000" device node.
This silences the following DTC compiler warning:
Warning (pwms_property): Missing property '#pwm-cells' in node
/soc/pwm@e6e31000 or bad phandle (referred from /backlight:pwms[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#phy-cells" property to "usb-phy@e65ee000" device node.
This silences the following DTC compiler warning:
Warning (phys_property): Missing property '#phy-cells' in node
/soc/usb-phy@e65ee000 or bad phandle (referred from
/soc/usb@ee020000:phys[0])
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove "reg" property from cache-controller-0 device node as it does not
have any unit address.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /cpus/cache-controller-0 has a reg
or ranges property, but no unit name
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "#address-cells" and "#size-cells" properties to all place-holder nodes
that have children nodes defined by salvator-x[s].dtsi device tree.
This silences the following DTC compiler warnings:
Warning (reg_format): "reg" property in /soc/.. has invalid length (4 bytes)
(#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells
value for /soc/...
Warning (avoid_default_addr_size): Relying on default #size-cells value
for /soc/...
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "reg" properties to place-holder nodes with unit address defined for
R-Car M3-N SoC.
This silences the following DTC compiler warning:
Warning (unit_address_vs_reg): Node /soc/... has a unit name,
but no reg property
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic support for R-Car Salvator-X M3-N (R8A77965) board.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Gen 3 R-Car M3-N SoC.
Based on original work from:
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe frequencies, other than the default for CA53 cores. This is a
pre-requisite for using providing alternative frequencies for use with
CPUFreq with these cores.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWqLBBgAKCRALBhiOFHI7
1dQ0AKCOUzXMHkC5/f0hwgPYpmzKuQGZjACfQA6eVistsl3QfTN0Nph57jRW9IE=
=KBPW
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.17 (part 1)" from Gregory CLEMENT:
- convert to the SPDX-License-Identifier
- add missing clocks (for the registers) on some of the peripherals
- use the new nand driver
- add more uart for Armada 7K/8K SoCs
* tag 'mvebu-dt64-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Add apb_pclk clock for the uart nodes
arm64: dts: marvell: use reworked NAND controller driver on Armada 8K
arm64: dts: marvell: use reworked NAND controller driver on Armada 7K
ARM64: dts: marvell: armada-cp110: Add registers clock for sata node
arm64: dts: marvell: armada-8080-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-mcbin: use SPDX-License-Identifier
arm64: dts: marvell: armada-8040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-7040-db: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-espressobin: use SPDX-License-Identifier
arm64: dts: marvell: armada-3720-db: use SPDX-License-Identifier
arm64: dts: marvell: use SPDX-License-Identifier for Armada SoCs
arm64: dts: marvell: mcbin: fix board name typo
arm64: dts: marvell: mcbin: enable uart headers
arm64: dts: marvell: add CP110 uart peripherals
ARM64: dts: marvell: armada-cp110: Add registers clock for I2C nodes
ARM64: dts: marvell: armada-cp110: Add registers clock for SPI nodes
- Add XGE CPLD control support for hip07 SoC
- Disable the SMMU on hip06 and hip07 SoCs becuase of
the hardware limitation
- Enable HS200 mode for the MMC controller on hi6220 hikey board
- Remove "cooling-{min|max}-level" this kind unused properties
for hi6220 SoC
- Add watchdog node for hi6220 SoC
- Remove "CPU_NAP" idle state on hikey960 board since it is
not stable and useless with the updated firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HIMw
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-4.17' of git://github.com/hisilicon/linux-hisi into next/dt
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.17" from Wei Xu:
- Add XGE CPLD control support for hip07 SoC
- Disable the SMMU on hip06 and hip07 SoCs becuase of
the hardware limitation
- Enable HS200 mode for the MMC controller on hi6220 hikey board
- Remove "cooling-{min|max}-level" this kind unused properties
for hi6220 SoC
- Add watchdog node for hi6220 SoC
- Remove "CPU_NAP" idle state on hikey960 board since it is
not stable and useless with the updated firmware
* tag 'hisi-arm64-dt-for-4.17' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Hi3660: Remove 'CPU_NAP' idle state
arm64: dts: hi6220: enable watchdog
ARM64: dts: hi6220: Remove "cooling-{min|max}-level" for CPU nodes
arm64: dts: hikey: Enable HS200 mode on eMMC
arm64: dts: hisi: Disable hisilicon smmu node on hip06/hip07
arm64: dts: hisi: add hns-dsaf cpld control for the hip07 SoC
