Kcov causes the compiler to add a call to __sanitizer_cov_trace_pc() in
every basic block. Ftrace patches in a call to _mcount() to each
function it has annotated.
Letting these mechanisms annotate each other is a bad thing. Break the
loop by adding 'notrace' to __sanitizer_cov_trace_pc() so that ftrace
won't try to patch this code.
This patch lets arm64 with KCOV and STACK_TRACER boot.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When kswapd goes to sleep it checks if the node is balanced and at first
it sleeps only for HZ/10 time, then rechecks if the node is still
balanced and nobody has woken it during the initial sleep. Only then it
goes fully sleep until an allocation slowpath wakes it up again.
For higher-order allocations, waking up kcompactd is done only before
the full sleep. This turns out to be an issue in case another
high-order allocation fails during the initial sleep. It will wake
kswapd up, however kswapd considers the zone balanced from the order-0
perspective, and will just quickly try to sleep again. So if there's a
longer stream of high-order allocations hitting the slowpath and waking
up kswapd, it might never actually wake up kcompactd, which may be
considered a regression from kswapd-based compaction. In the worst
case, it might be that a single allocation that cannot direct
reclaim/compact itself is waking kswapd in the retry loop and preventing
kcompactd from being woken up and unblocking it.
This patch makes sure kcompactd is woken up in such situations by simply
moving the wakeup before the short initial sleep. More efficient
solution would be to wake kcompactd immediately instead of kswapd if the
node is already order-0 balanced, but in that case we should also move
reset_isolation_suitable() call to kcompactd so it's not adding to the
allocator's latency. Since it's late in the 4.6 cycle, let's go with
the simpler change for now.
Fixes: accf62422b ("mm, kswapd: replace kswapd compaction with waking up kcompactd")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: David Rientjes <rientjes@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set current email address to replace obsolete email addresses.
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, migration code increses num_poisoned_pages on *failed*
migration page as well as successfully migrated one at the trial of
memory-failure. It will make the stat wrong. As well, it marks the
page as PG_HWPoison even if the migration trial failed. It would mean
we cannot recover the corrupted page using memory-failure facility.
This patches fixes it.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyeongdon reported below error which is BUG_ON(!PageSwapCache(page)) in
page_swap_info. The reason is that page_endio in rw_page unlocks the
page if read I/O is completed so we need to hold a PG_lock again to
check PageSwapCache. Otherwise, the page can be removed from swapcache.
Kernel BUG at c00f9040 [verbose debug info unavailable]
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 4 PID: 13446 Comm: RenderThread Tainted: G W 3.10.84-g9f14aec-dirty #73
task: c3b73200 ti: dd192000 task.ti: dd192000
PC is at page_swap_info+0x10/0x2c
LR is at swap_slot_free_notify+0x18/0x6c
pc : [<c00f9040>] lr : [<c00f5560>] psr: 400f0113
sp : dd193d78 ip : c2deb1e4 fp : da015180
r10: 00000000 r9 : 000200da r8 : c120fe08
r7 : 00000000 r6 : 00000000 r5 : c249a6c0 r4 : = c249a6c0
r3 : 00000000 r2 : 40080009 r1 : 200f0113 r0 : = c249a6c0
..<snip> ..
Call Trace:
page_swap_info+0x10/0x2c
swap_slot_free_notify+0x18/0x6c
swap_readpage+0x90/0x11c
read_swap_cache_async+0x134/0x1ac
swapin_readahead+0x70/0xb0
handle_pte_fault+0x320/0x6fc
handle_mm_fault+0xc0/0xf0
do_page_fault+0x11c/0x36c
do_DataAbort+0x34/0x118
Fixes: 3f2b1a04f4 ("zram: revive swap_slot_free_notify")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Tested-by: Kyeongdon Kim <kyeongdon.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have been reclaimed highmem zone if buffer_heads is over limit but
commit 6b4f7799c6 ("mm: vmscan: invoke slab shrinkers from
shrink_zone()") changed the behavior so it doesn't reclaim highmem zone
although buffer_heads is over the limit. This patch restores the logic.
Fixes: 6b4f7799c6 ("mm: vmscan: invoke slab shrinkers from shrink_zone()")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In gather_pte_stats() a THP pmd is cast into a pte, which is wrong
because the layouts may differ depending on the architecture. On s390
this will lead to inaccurate numa_maps accounting in /proc because of
misguided pte_present() and pte_dirty() checks on the fake pte.
On other architectures pte_present() and pte_dirty() may work by chance,
but there may be an issue with direct-access (dax) mappings w/o
underlying struct pages when HAVE_PTE_SPECIAL is set and THP is
available. In vm_normal_page() the fake pte will be checked with
pte_special() and because there is no "special" bit in a pmd, this will
always return false and the VM_PFNMAP | VM_MIXEDMAP checking will be
skipped. On dax mappings w/o struct pages, an invalid struct page
pointer would then be returned that can crash the kernel.
This patch fixes the numa_maps THP handling by introducing new "_pmd"
variants of the can_gather_numa_stats() and vm_normal_page() functions.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> [4.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Khugepaged detects own VMAs by checking vm_file and vm_ops but this way
it cannot distinguish private /dev/zero mappings from other special
mappings like /dev/hpet which has no vm_ops and popultes PTEs in mmap.
This fixes false-positive VM_BUG_ON and prevents installing THP where
they are not expected.
Link: http://lkml.kernel.org/r/CACT4Y+ZmuZMV5CjSFOeXviwQdABAgT7T+StKfTqan9YDtgEi5g@mail.gmail.com
Fixes: 78f11a2557 ("mm: thp: fix /dev/zero MAP_PRIVATE and vm_flags cleanups")
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patchwork introduced a garbled Polish character in commit 1e3012d0fd
("crypto: s5p-sss - Use memcpy_toio for iomem annotated memory") so fix
the mail mapping. Additionally prefer to use kernel.org account for
personal work, instead of my gmail address.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrea has found[1] a race condition on MMU-gather based TLB flush vs
split_huge_page() or shrinker which frees huge zero under us (patch 1/2
and 2/2 respectively).
With new THP refcounting, we don't need patch 1/2: mmu_gather keeps the
page pinned until flush is complete and the pin prevents the page from
being split under us.
We still need patch 2/2. This is simplified version of Andrea's patch.
We don't need fancy encoding.
[1] http://lkml.kernel.org/r/1447938052-22165-1-git-send-email-aarcange@redhat.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HugeTLB pages cannot be split, so we use the compound_mapcount to track
rmaps.
Currently page_mapped() will check the compound_mapcount, but will also
go through the constituent pages of a THP compound page and query the
individual _mapcount's too.
Unfortunately, page_mapped() does not distinguish between HugeTLB and
THP compound pages and assumes that a compound page always needs to have
HPAGE_PMD_NR pages querying.
For most cases when dealing with HugeTLB this is just inefficient, but
for scenarios where the HugeTLB page size is less than the pmd block
size (e.g. when using contiguous bit on ARM) this can lead to crashes.
This patch adjusts the page_mapped function such that we skip the
unnecessary THP reference checks for HugeTLB pages.
Fixes: e1534ae950 ("mm: differentiate page_mapped() from page_mapcount() for compound pages")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PageAnon() always look at head page to check PAGE_MAPPING_ANON and tail
page's page->mapping has just a poisoned data since commit 1c290f6421
("mm: sanitize page->mapping for tail pages").
If makedumpfile checks page->mapping of a compound tail page to
distinguish anonymous page as usual, it must fail in newer kernel. So
it's necessary to export OFFSET(page.compound_head) to avoid checking
compound tail pages.
The problem is that unnecessary hugepages won't be removed from a dump
file in kernels 4.5.x and later. This means that extra disk space would
be consumed. It's a problem, but not critical.
Signed-off-by: Atsushi Kumagai <ats-kumagai@wm.jp.nec.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
makedumpfile refers page.lru.next to get the order of compound pages for
page filtering.
However, now the order is stored in page.compound_order, hence
VMCOREINFO should be updated to export the offset of
page.compound_order.
The fact is, page.compound_order was introduced already in kernel 4.0,
but the offset of it was the same as page.lru.next until kernel 4.3, so
this was not actual problem.
The above can be said also for page.lru.prev and page.compound_dtor,
it's necessary to detect hugetlbfs pages. Further, the content was
changed from direct address to the ID which means dtor.
The problem is that unnecessary hugepages won't be removed from a dump
file in kernels 4.4.x and later. This means that extra disk space would
be consumed. It's a problem, but not critical.
Signed-off-by: Atsushi Kumagai <ats-kumagai@wm.jp.nec.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull Ceph fixes from Sage Weil:
"There is a lifecycle fix in the auth code, a fix for a narrow race
condition on map, and a helpful message in the log when there is a
feature mismatch (which happens frequently now that the default
server-side options have changed)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: report unsupported features to syslog
rbd: fix rbd map vs notify races
libceph: make authorizer destruction independent of ceph_auth_client
Pull s390 fixes from Martin Schwidefsky:
"Three more bug fixes for 4.6
- Due to a race in the dynamic page table code a multi-threaded
program can cause a translation specification exception. With
panic_on_oops a user space program can crash the system.
- An information leak with the /dev/sclp device.
- A use after free in the s390 PCI code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/sclp_ctl: fix potential information leak with /dev/sclp
s390/mm: fix asce_bits handling with dynamic pagetable levels
s390/pci: fix use after free in dma_init
Alternatively one could free the skb, OTOH I don't think this test is
useful so just remove it.
Cc: <linux-rdma@vger.kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Alexei Starovoitov says:
====================
bpf: fix several bugs
First two patches address bugs found by Jann Horn.
Last patch is a minor samples fix spotted during the testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
llvm cannot always recognize memset as builtin function and optimize
it away, so just delete it. It was a leftover from testing
of bpf_perf_event_output() with large data structures.
Fixes: 39111695b1 ("samples: bpf: add bpf_perf_event_output example")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 35578d7984 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter")
introduced clever way to check bpf_helper<->map_type compatibility.
Later on commit a43eec3042 ("bpf: introduce bpf_perf_event_output() helper") adjusted
the logic and inadvertently broke it.
Get rid of the clever bool compare and go back to two-way check
from map and from helper perspective.
Fixes: a43eec3042 ("bpf: introduce bpf_perf_event_output() helper")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a system with >32Gbyte of phyiscal memory and infinite RLIMIT_MEMLOCK,
the malicious application may overflow 32-bit bpf program refcnt.
It's also possible to overflow map refcnt on 1Tb system.
Impose 32k hard limit which means that the same bpf program or
map cannot be shared by more than 32k processes.
Fixes: 1be7f75d16 ("bpf: enable non-root eBPF programs")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Rivshin says:
====================
drivers: net: cpsw: phy-handle fixes
This series fixes a number of related issues around using phy-handle
properties in cpsw emac nodes.
Patch 1 fixes a bug if more than one slave is used, and either
slave uses the phy-handle property in the devicetree.
Patch 2 fixes a NULL pointer dereference which can occur if a
phy-handle property is used and of_phy_connect() return NULL,
such as with a bad devicetree.
Patch 3 fixes an issue where the phy-mode property would be ignored
if a phy-handle property was used. This also fixes a bogus error
message that would be emitted.
Patch 4 fixes makes the binding documentation more explicit that
exactly one PHY property should be used, and also marks phy_id as
deprecated.
Patch 5 cleans up the fixed-link case to work like the now-fixed
phy-handle case.
I have tested on the following hardware configurations:
- (EVMSK) dual emac, phy_id property in both slaves
- (EVMSK) dual emac, phy-handle property in both slaves
- (EVMSK) a bad phy-handle property pointing to &mmc1
- (EVMSK) phy_id property with incorrect PHY address
- (BeagleBoneBlack) single emac, phy_id property
- (custom) single emac, fixed-link subnode
Andrew Goodbody reported testing v2 on a board that doesn't use
dual_emac mode, but with 2 PHYs using phy-handle properties [1].
Nicolas Chauvet reported testing v2 on an HP t410 (dm8148).
Markus Brunner reported testing v1 on the following [2]:
- emac0 with phy_id and emac1 with fixed phy
- emac0 with phy-handle and emac1 with fixed phy
- emac0 with fixed phy and emac1 with fixed phy
[1] https://lkml.org/lkml/2016/4/22/537
[2] http://www.spinics.net/lists/netdev/msg357890.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a fixed-link DT subnode is used, the phy_device was looked up so
that a PHY ID string could be constructed and passed to phy_connect().
This is not necessary, as the device_node can be passed directly to
of_phy_connect() instead. This reuses the same codepath as if the
phy-handle DT property was used.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-handle, phy_id, and fixed-link properties are mutually exclusive,
and only one need be specified. Make this clear in the binding doc.
Also mark the phy_id property as deprecated, as phy-handle should be
used instead.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-mode emac property was only being processed in the phy_id
or fixed-link cases. However if phy-handle was specified instead,
an error message would complain about the lack of phy_id or
fixed-link, and then jump past the of_get_phy_mode(). This would
result in the PHY mode defaulting to MII, regardless of what the
devicetree specified.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.
Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9e42f71526 ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.
This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When newlink creation fails at device-registration, the port->count
is decremented twice. Francesco Ruggeri (fruggeri@arista.com) found
this issue in Macvlan and the same exists in IPvlan driver too.
While fixing this issue I noticed another issue of missing unregister
in case of failure, so adding it to the fix which is similar to the
macvlan fix by Francesco in commit 3083796075 ("macvlan: fix failure
during registration v3")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_tx_ring.tx_lock is only used in the hard_xmit handler and
in the transmit completion reaper called from NAPI context.
Compile-tested only. Potential victims Cced.
Someone more knowledgeable may check if pch_gbe_tx_queue could
have some use for a mmiowb.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Cress <andy.cress@us.kontron.com>
Cc: bryan@fossetcon.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch overloads the DSA master netdev, aka CPU Ethernet MAC to also
include switch-side statistics, which is useful for debugging purposes,
when the switch is not properly connected to the Ethernet MAC (duplex
mismatch, (RG)MII electrical issues etc.).
We accomplish this by retaining the original copy of the master netdev's
ethtool_ops, and just overload the 3 operations we care about:
get_sset_count, get_strings and get_ethtool_stats so as to intercept
these calls and call into the original master_netdev ethtool_ops, plus
our own.
We take this approach as opposed to providing a set of DSA helper
functions that would retrive the CPU port's statistics, because the
entire purpose of DSA is to allow unmodified Ethernet MAC drivers to be
used as CPU conduit interfaces, therefore, statistics overlay in such
drivers would simply not scale.
The new ethtool -S <iface> output would therefore look like this now:
<iface> statistics
p<2 digits cpu port number>_<switch MIB counter names>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP prequeue goal is to defer processing of incoming packets
to user space thread currently blocked in a recvmsg() system call.
Intent is to spend less time processing these packets on behalf
of softirq handler, as softirq handler is unfair to normal process
scheduler decisions, as it might interrupt threads that do not
even use networking.
Current prequeue implementation has following issues :
1) It only checks size of the prequeue against sk_rcvbuf
It was fine 15 years ago when sk_rcvbuf was in the 64KB vicinity.
But we now have ~8MB values to cope with modern networking needs.
We have to add sk_rmem_alloc in the equation, since out of order
packets can definitely use up to sk_rcvbuf memory themselves.
2) Even with a fixed memory truesize check, prequeue can be filled
by thousands of packets. When prequeue needs to be flushed, either
from sofirq context (in tcp_prequeue() or timer code), or process
context (in tcp_prequeue_process()), this adds a latency spike
which is often not desirable.
I added a fixed limit of 32 packets, as this translated to a max
flush time of 60 us on my test hosts.
Also note that all packets in prequeue are not accounted for tcp_mem,
since they are not charged against sk_forward_alloc at this point.
This is probably not a big deal.
Note that this might increase LINUX_MIB_TCPPREQUEUEDROPPED counts,
which is misnamed, as packets are not dropped at all, but rather pushed
to the stack (where they can be either consumed or dropped)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The collect metadata mode does not support GUE nor FOU. This might be
implemented later; until then, we should reject such config.
I think this is okay to be changed. It's unlikely anyone has such
configuration (as it doesn't work anyway) and we may need a way to
distinguish whether it's supported or not by the kernel later.
For backwards compatibility with iproute2, it's not possible to just check
the attribute presence (iproute2 always includes the attribute), the actual
value has to be checked, too.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petko Manolov says:
====================
pegasus: correct buffer & packet sizes
As noticed by Lincoln Ramsay <a1291762@gmail.com> some old (usb 1.1) Pegasus
based devices may actually return more bytes than the specified in the datasheet
amount. That would not be a problem if the allocated space for the SKB was
equal to the parameter passed to usb_fill_bulk_urb(). Some poor bugger (i
really hope it was not me, but 'git blame' is useless in this case, so anyway)
decided to add '+ 8' to the buffer length parameter. Sometimes the usb transfer
overflows and corrupts the socket structure, leading to kernel panic.
The above doesn't seem to happen for newer (Pegasus2 based) devices which did
help this bug to hide for so long.
The new default is to not include the CRC at the end of each received package.
So far CRC has been ignored which makes no sense to do it in a first place.
The patch is against v4.6-rc5 and was tested on ADM8515 device by transferring
multiple gigabytes of data over a couple of days without any complaints from the
kernel. Please apply it to whatever net tree you deem fit.
Changes since v1:
- split the patch in two parts;
- corrected the subject lines;
Changes since v2:
- do not append CRC by default (based on a discussion with Johannes Berg);
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The default Pegasus setup was to append the status and CRC at the end of each
received packet. The status bits are used to update various stats, but CRC has
been ignored. The new default is to not append CRC at the end of RX packets.
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: Lincoln Ramsay <a1291762@gmail.com>
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 (which will be the first user of the
fq.h) recently started to support software A-MSDU
aggregation. It glues skbuffs together into a
single one so the backlog accounting needs to be
more fine-grained.
To avoid backlog sorting logic duplication split
it up for re-use.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
gre: fix lwtunnel support
This patchset fixes a few bugs in ipgre metadata mode implementation.
As an example, in this setup:
ip a a 192.168.1.1/24 dev eth0
ip l a gre1 type gre external
ip l s gre1 up
ip a a 192.168.99.1/24 dev gre1
ip r a 192.168.99.2/32 encap ip dst 192.168.1.2 ttl 10 dev gre1
ping 192.168.99.2
the traffic does not go through before this patchset and does as expected
with it applied.
v3: Back to v1 in order not to break existing users. Dropped patch 3, will
be fixed in iproute2 instead.
v2: Rejecting invalid configuration, added patch 3, dropped patch for
ETH_P_TEB (will target net-next).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipgre (i.e. not gretap) + collect metadata mode, the skb was assumed to
contain Ethernet header and was encapsulated as ETH_P_TEB. This is not the
case, the interface is ARPHRD_IPGRE and the protocol to be used for
encapsulation is skb->protocol.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipgre mode (i.e. not gretap) with collect metadata flag set, the tunnel
is incorrectly assumed to be mGRE in NBMA mode (see commit 6a5f44d7a0).
This is not the case, we're controlling the encapsulation addresses by
lwtunnel metadata. And anyway, assigning dev->header_ops in collect metadata
mode does not make sense.
Although it would be more user firendly to reject requests that specify
both the collect metadata flag and a remote/local IP address, this would
break current users of gretap or introduce ugly code and differences in
handling ipgre and gretap configuration. Keep the current behavior of
remote/local IP address being ignored in such case.
v3: Back to v1, added explanation paragraph.
v2: Reject configuration specifying both remote/local address and collect
metadata flag.
Fixes: 2e15ea390e ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(root user triggerable) error case.
-----BEGIN PGP SIGNATURE-----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=EWBn
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a single fix, for a per-CPU memory leak in a
(root user triggerable) error case.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is never called with a NULL "buf" and anyway, we dereference 's' on
the lines before so it would Oops before we reach the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030. However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct mlx5e_channel_param is a large structure that is allocated
on the stack of mlx5e_open_channels, and with a recent change
it has grown beyond the warning size for the maximum stack
that a single function should use:
mellanox/mlx5/core/en_main.c: In function 'mlx5e_open_channels':
mellanox/mlx5/core/en_main.c:1325:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The function is already using dynamic allocation and is not in
a fast path, so the easiest workaround is to use another kzalloc
for allocating the channel parameters.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) check skb size to avoid reading beyond its border when delivering
payloads, by Sven Eckelmann
2) initialize last_seen time in neigh_node object to prevent cleanup
routine from accidentally purge it, by Marek Lindner
3) release "recently added" slave interfaces upon virtual/batman
interface shutdown, by Sven Eckelmann
4) properly decrease router object reference counter upon routing table
update, by Sven Eckelmann
5) release queue slots when purging OGM packets of deactivating slave
interface, by Linus Lüssing
Patch 2 and 3 have no "Fixes:" tag because the offending commits date
back to when batman-adv was not yet officially in the net tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=o059
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
In this patchset you can find the following fixes:
1) check skb size to avoid reading beyond its border when delivering
payloads, by Sven Eckelmann
2) initialize last_seen time in neigh_node object to prevent cleanup
routine from accidentally purge it, by Marek Lindner
3) release "recently added" slave interfaces upon virtual/batman
interface shutdown, by Sven Eckelmann
4) properly decrease router object reference counter upon routing table
update, by Sven Eckelmann
5) release queue slots when purging OGM packets of deactivating slave
interface, by Linus Lüssing
Patch 2 and 3 have no "Fixes:" tag because the offending commits date
back to when batman-adv was not yet officially in the net tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to calculate rps hash if it was not enabled. So this
patch export rps_needed and check it before trying to get rps
hash. Tests (using pktgen to inject packets to guest) shows this can
improve pps about 13% (when rps is disabled).
Before:
~1150000 pps
After:
~1300000 pps
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
----
Changes from V1:
- Fix build when CONFIG_RPS is not set
Signed-off-by: David S. Miller <davem@davemloft.net>
The size allocated for target->hwinfo and the number of bytes copied in it
should be consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
