MCP251xFD supports internal loopback mode which can be used to verify CAN
functionality in the absence of a real CAN device.
Link: https://lore.kernel.org/r/20201201054019.11012-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[mkl: mcp251xfd_get_normal_mode(): move CAN_CTRLMODE_LOOPBACK check to front]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan driver runs only on DT platforms, so simplify the code by using
of_device_get_match_data() to retrieve the driver data and also by removing the
unused id_table.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201128132855.7724-1-festevam@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus.
It integrates the Bosch M_CAN controller with Message RAM and the wrapper IP
block with additional registers which all of them are within the same MMIO
range.
Currently only interrupt control register from wrapper IP is used and the MRAM
configuration is expected to come from the firmware via "bosch,mram-cfg" device
property and parsed by m_can.c core.
Initial implementation is done by Felipe Balbi while he was working at Intel
with later changes from Raymond Tan and me.
Co-developed-by: Felipe Balbi (Intel) <balbi@kernel.org>
Co-developed-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Felipe Balbi (Intel) <balbi@kernel.org>
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20201117160827.3636264-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparatory patch for upcoming PCI based M_CAN devices. The current
PM implementation would cause PCI based drivers to enable PM twice, once when
the PCI device is added and a second time in m_can_class_register(). This will
cause 'Unbalanced pm_runtime_enable!' to be logged, and is a situation that
should be avoided.
Therefore, in anticipation of PCI devices, move PM enabling out from M_CAN
class registration to its only user, the m_can_platform driver.
Signed-off-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Link: https://lore.kernel.org/r/20201023115800.46538-2-patrik.flykt@linux.intel.com
[mkl: m_can_plat_probe(): fix error handling
m_can_class_register(): simplify error handling]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CSR bit is already cleared when arriving here so remove this section of
duplicate code.
The registers set in m_can_config_endisable() is set to same exact values as
before this patch.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20191211063227.84259-1-sean@geanix.com
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The definition of IS_ERR() already applies the unlikely() notation when
checking the error status of the passed pointer. For this reason there is no
need to have the same notation outside of IS_ERR() itself.
Clean up code by removing redundant notation.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Link: https://lore.kernel.org/r/20201210085321.18693-1-a@unstable.cc
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the function m_can_class_unregister() directly after the
m_can_class_register() function.
Link: https://lore.kernel.org/r/20201130133713.269256-7-mkl@pengutronix.de
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There's no need to unset the drvdata on remove, so remove the unneeded call to
platform_set_drvdata() in m_can_plat_remove().
Link: https://lore.kernel.org/r/20201130133713.269256-6-mkl@pengutronix.de
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Both struct tcan4x5x_priv::mram_start and struct tcan4x5x_priv::reg_offset are
only assigned once with a constant and then always used read-only. This patch
changes the driver to use the constant directly instead.
Link: https://lore.kernel.org/r/20201130133713.269256-2-mkl@pengutronix.de
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename the tcan4x5x_parse_config() function to tcan4x5x_get_gpios() since the
function retrieves the gpio configurations from the firmware.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: http://lore.kernel.org/r/20200226140358.30017-1-dmurphy@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the error handling in c_can_power_up(), there are two bugs:
1) c_can_pm_runtime_get_sync() will increase usage counter if device is not
empty. Forgetting to call c_can_pm_runtime_put_sync() will result in a
reference leak here.
2) c_can_reset_ram() operation will set start bit when enable is true. We
should clear it in the error handling.
We fix it by adding c_can_pm_runtime_put_sync() for 1), and
c_can_reset_ram(enable is false) for 2) in the error handling.
Fixes: 8212003260 ("can: c_can: Add d_can suspend resume support")
Fixes: 52cde85acc ("can: c_can: Add d_can raminit support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201128133922.3276973-2-zhangqilong3@huawei.com
[mkl: return "0" instead of "ret"]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sun4i driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sja1000 driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 8935f57e68 ("can: sja1000: fix network statistics update")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The clocks mcan_class->cclk and mcan_class->hclk are not prepared by any call
during tcan4x5x_can_probe(), so remove erroneous clk_disable_unprepare() on
them.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Link: http://lore.kernel.org/r/20201130114252.215334-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes a redundant return at the end of
tcan4x5x_clear_interrupts().
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: http://lore.kernel.org/r/20191211141635.322577-1-sean@geanix.com
Reported-by: Daniels Umanovskis <daniels@umanovskis.se>
Acked-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reduce the number of separate SPI core requests when setting the UINC bit in
the TEF FIFO, and instead batch them up into a single SPI core request.
Link: https://lore.kernel.org/r/20201126132144.351154-6-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the struct mcp251xfd_tef_ring upwards, so that the union
mcp251xfd_write_reg_buf and struct spi_transfer can be made members of it.
Link: https://lore.kernel.org/r/20201126132144.351154-5-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the struct mcp251xfd_tef_ring member within the struct
mcp251xfd_priv into an array of length one. This way all rings (tef, tx and rx)
can be accessed in the same way.
Link: https://lore.kernel.org/r/20201126132144.351154-4-mkl@pengutronix.de
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by
moving the "default" to the end of the "switch" statement and explicitly adding
a break statement instead of letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: http://lore.kernel.org/r/aab7cf16bf43cc7c3e9c9930d2dae850c1d07a3c.1605896059.git.gustavoars@kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[mkl: move default to end]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It would directly return if the variable err equals to 0 or other errors.
Only when the err equals to -ETIMEDOUT it can reach the 'if (err)'
statement, so the 'if (err)' and last 'return -ETIMEDOUT' statements are
useless. Romove them.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1605605352-25298-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for a new variant of devices using the hydra platform, based on
NXP i.MX RT (flexcan).
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-5-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add USB_{LEAF,HYDRA}_PRODUCT_ID_END defines, representing the last USB PID
entry in respectively family. This removes the need to update the
kvaser_is_{leaf,hydra}() functions whenever new devices are added.
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-3-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There haven been reports, that the flexcan_close() soradically hangs during
simultanious ifdown, sending of CAN messages and probably open CAN bus:
| (__schedule) from [<808bbd34>] (schedule+0x90/0xb8)
| (schedule) from [<808bf274>] (schedule_timeout+0x1f8/0x24c)
| (schedule_timeout) from [<8016be44>] (msleep+0x18/0x1c)
| (msleep) from [<80746a64>] (napi_disable+0x60/0x70)
| (napi_disable) from [<8052fdd0>] (flexcan_close+0x2c/0x140)
| (flexcan_close) from [<80744930>] (__dev_close_many+0xb8/0xd8)
| (__dev_close_many) from [<8074db9c>] (__dev_change_flags+0xd0/0x1a0)
| (__dev_change_flags) from [<8074dc84>] (dev_change_flags+0x18/0x48)
| (dev_change_flags) from [<80760c24>] (do_setlink+0x44c/0x7b4)
| (do_setlink) from [<80761560>] (rtnl_newlink+0x374/0x68c)
I was unable to reproduce the issue, but a cleanup of the flexcan close
sequence has probably fixed the problem at the reporting user.
This patch changes the sequence in flexcan_close() to:
- stop the TX queue
- disable the interrupts on the chip level and wait via free_irq()
synchronously for the interrupt handler to finish
- disable RX offload, which disables synchronously NAPI
- disable the flexcan on the chip level
- free RX offload
- disable the transceiver
- close the CAN device
- disable the clocks
Link: https://lore.kernel.org/r/20201119100917.3013281-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the order in which the flexcan controller is brought up
during flexcan_open(). It makes sure that the chip is completely initialized
before the IRQs are requested and finally enabled.
Link: https://lore.kernel.org/r/20201119100917.3013281-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function flexcan_chip_start() first configures the CAN controller and then
enables the interrupt, flexcan_chip_stop() does the opposite.
In an upcoming patch the order of operations in flexcan_open() and
flexcan_close() are changed. This requires
flexcan_chip_start()/flexcan_chip_stop_disable_on_error() and
flexcan_chip_interrupts_{enable,disable}() to be independent of each other.
This patch moves the enabling of the interrupts from flexcan_chip_start() to
its callers flexcan_open() and flexcan_resume(). Likewise the disabling of the
interrupts is moved from __flexcan_chip_stop() to its indirect callers
flexcan_close() and flexcan_suspend().
Link: https://lore.kernel.org/r/20201119100917.3013281-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The upcoming patches are going to move the enabling and disabling of the
interrupts. Introduce convenience functions to make these patches simpler.
Link: https://lore.kernel.org/r/20201119100917.3013281-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch intends to rename FLEXCAN_QUIRK_SETUP_STOP_MODE quirk
to FLEXCAN_QUIRK_SETUP_STOP_MODE_GRP for non-scu SoCs, coming patch will
add quirk for scu SoCs.
For non-scu SoCs, setup stop mode with GPR register.
For scu SoCs, setup stop mode with SCU firmware.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-4-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Support the Classical CAN raw DLC functionality to send and receive DLC values
from 9 .. 15 for the Classical CAN capable CAN network driver esd_usb that
supports the esd CAN-USB/2 and CAN-USB/Micro devices:
- esd_usb2
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Tested-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://lore.kernel.org/r/20201116184430.25462-2-stefan.maetje@esd.eu
[mkl: rewrapped some long lines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Support the Classical CAN raw DLC functionality to send and receive DLC values
from 9 .. 15 on various Classical CAN capable CAN network drivers:
- sja1000
- gs_usb
- pcan_usb
- pcan_usb_fd
- usb_8dev
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201111095923.2535-1-socketcan@hartkopp.net
[mkl: usb_8dev: changed indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The helper functions can_len2dlc and can_dlc2len are only relevant for
CAN FD data length code (DLC) conversion.
To fit the introduced can_cc_dlc2len for Classical CAN we rename:
can_dlc2len -> can_fd_dlc2len to get the payload length from the DLC
can_len2dlc -> can_fd_len2dlc to get the DLC from the payload length
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The macro was always used together with can_dlc2len() which sanitizes the
given dlc value on its own.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-4-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).
Rename the macro and use the correct constant in preparation of the len/dlc
cleanup for Classical CAN frames.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
