controllers with XHCI_AVOID_BEI quirk cause too frequent interrupts
and affect power management.
To avoid interrupting on every isochronous interval the BEI (Block
Event Interrupt) flag is set for all except the last Isoch TRB in a URB.
This lead to event ring filling up in case several isoc URB were
queued and cancelled rapidly, which some controllers didn't
handle well, and thus the XHCI_AVOID_BEI quirk was introduced.
see commit 227a4fd801 ("usb: xhci: apply XHCI_AVOID_BEI quirk to all
Intel xHCI controllers")
With the XHCI_AVOID_BEI quirk each Isoch TRB will trigger an interrupt.
This can cause up to 8000 interrupts per second for isochronous transfers
with HD USB3 cameras, affecting power saving.
The event ring fits 256 events, instead of interrupting on every
isochronous TRB if XHCI_AVOID_BEI is set we make sure at least every
8th Isochronous TRB asserts an interrupt, clearing the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this change, there will be a wakeup entry at /sys/../power/wakeup,
and the user could use this entry to choose whether enable xhci wakeup
features (wake up system from suspend) or not.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The if {} condition is duplicated with outer if {} condition.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms (eg cdns3) may have special sequences between
xhci_bus_suspend and xhci_suspend, add .suspend_quick for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some xhci hosts (eg dwc3 and cdns3) do not use OF to create
platform device, they create xhci-plat platform device runtime.
And these platforms may also have quirks, and the quirks could
be supplied by their parent device through platform data.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Buffers should be u8*, not unsigned char*
Buffers have an unsigned length and using an int
as a boolean is a bit outdated.
No functional change intended.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200917110235.11854-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ROLE_CONTROL register would not have the actual CC terminations
unless the port does not set ROLE_CONTROL.DRP. For DRP ports,
CC_STATUS.cc1/cc2 indicates the final terminations applied
when TCPC enters potential_connect_as_source/_sink.
For DRP ports, infer port role from CC_STATUS and set corresponding
CC terminations before setting the orientation.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI spec forbids direct access of TX_BUF_BYTE_x register.
The existing version of tcpci driver assumes that those registers
are directly addressible. Add support for tcpci chips which do
not support direct access to TX_BUF_BYTE_x registers. TX_BUF_BYTE_x
can only be accessed by I2C_WRITE_BYTE_COUNT.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer has introduced a new macro for recording the result
of a command. Use it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC expects the USB Type-C ports numbers to be starting with 0.
If the port number is passed as it is, the IOM status will not be
updated. The IOM port status check fails which will eventually
lead to PMC IPC communication failure.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Suggested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver now needs to find the IOM ACPI node, the
driver depends on ACPI. Without the dependency set, the
driver will only fail to compile when ACPI is not enabled.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_recv() function can handle data on the stack, as
well as properly detecting short reads, so move to use that function
instead of the older usb_control_msg() call. This ends up removing a
lot of extra lines in the driver.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler and the code smaller.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200914153756.3412156-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New core functions to make sending/receiving USB control messages easier
and saner.
In discussions, it turns out that the large majority of users of
usb_control_msg() do so in potentially incorrect ways. The most common
issue is where a "short" message is received, yet never detected
properly due to "incorrect" error handling.
Handle all of this in the USB core with two new functions to try to make
working with USB control messages simpler.
No more need for dynamic data, messages can be on the stack, and only
"complete" send/receive will work without causing an error.
Link: https://lore.kernel.org/r/20200914153756.3412156-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usb_pipe_sanity_check() is a great function, so let's move it into
the USB core so that other parts of the kernel, including the USB core,
can call it.
Name it usb_pipe_type_check() to match the existing
usb_urb_ep_type_check() call, which now uses this function.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Eli Billauer <eli.billauer@gmail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Tsoy <alexander@tsoy.me>
Cc: "Geoffrey D. Bennett" <g@b4.vu>
Cc: Jussi Laako <jussi@sonarnerd.net>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Dmitry Panchenko <dmitry@d-systems.ee>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jesus Ramos <jesus-ramos@live.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek MT6360 is a multi-functional IC that includes USB Type-C.
It works with Type-C Port Controller Manager to provide USB PD
and USB Type-C functionalities.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1598928042-22115-1-git-send-email-u0084500@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'distrust_firmware' module parameter dates from 2004 and the USB
subsystem is a lot more mature and reliable now than it was then.
Alter the default to false now.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-2-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci controller found in some Broadcom switches with integrated SoCs
has an issue which causes a soft lockup with large transfers like you
see when running ext4 on USB3 flash drive.
Port the fix from the Broadcom XLDK to increase the OUT_THRESHOLD to
avoid the problem.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200913215926.29880-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX1embwAKCRALxc3C7H1l
CLYoAQDVrO56s8bOd5JW3NpuDCDUgDSt3dBrXNF+PhHKX0TDAAEAztQesI4MgXLz
p0X1nJvdlwQgRTTJzI84HaUTRZk+EQc=
=1W7v
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.9-rc5
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: support dynamic Quectel USB compositions
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
This adds support for device data role, and data role
swapping. The driver no longer relies on the cached role, as
it may not be valid (for example after bootup). Instead, the
role is always checked by readding the port status from IOM.
Note. After this, the orientation is always only cached, so
the driver does not support scenario where the role is set
before orientation. It means the typec drivers must always
set the orientation first before role.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMC microcontroller that we use for configuration, does
not supply any status information back. For port status we
need to talk to another controller on the board called IOM
(I/O manager).
By checking the port status before configuring the muxes, we
can make sure that we do not reconfigure the port after
bootup when the system firmware (for example BIOS) has
already configured it.
Using the status information also to check if DisplayPort
HPD is still asserted when the cable plug is disconnected,
and clearing it if it is.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bits 4 and 5 are reserved in Alternate modes.
SBU Orientation and HSL Orientation needs to be configured only during
initial cable detection in USB connect flow based on device property of
"sbu-orientation" and "hsl-orientation".
Configuring these reserved bits in the Alternate modes may result in delay
in display link training or some unexpected behaviour.
So do not configure them while issuing Alternate Mode requests.
Fixes: ff4a30d5e2 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation")
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bit 14 is reserved in Alternate mode.
In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the
status update command VDO is set to HPD_HIGH, HPD is configured via
separate HPD mode request after configuring DP Alternate mode request.
Configuring reserved bit may show unexpected behaviour.
So do not configure them while issuing the Alternate Mode request.
Fixes: 7990be48ef ("usb: typec: mux: intel: Handle alt mode HPD_HIGH")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no reason for uas to use a smaller value of max_sectors than
usb-storage.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-3-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_add_host_with_dma() instead of scsi_add_host().
When the scsi request queue is initialized/allocated, hw_max_sectors is clamped
to the dma max mapping size. Therefore, the correct device that should be used
for the clamping needs to be set.
The same clamping is still needed in uas as hw_max_sectors could be changed
there. The original clamping would be invalidated in such cases.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-2-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_add_host_with_dma() instead of scsi_add_host().
When the scsi request queue is initialized/allocated, hw_max_sectors is clamped
to the dma max mapping size. Therefore, the correct device that should be used
for the clamping needs to be set.
The same clamping is still needed in usb-storage as hw_max_sectors could be
changed there. The original clamping would be invalidated in such cases.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-1-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-4-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-5-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903112554.34263-8-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903112554.34263-9-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8bb54ab573 ("usbcore: add usb_device_driver definition") added
the printk() calls with the error massages spoilt due to the stray tabs
in the middle. Remove these tabs and convert printk() calls to pr_err()
for consistency with the other code, while at it.
Fixes: 8bb54ab573 ("usbcore: add usb_device_driver definition")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/4beb55c4-eb34-7744-155f-033b8f527e23@omprussia.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7a410953d1.
This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.
In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.
Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.
Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.
Fixes: 7a410953d1 ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
