According to the documentation, the limit is 0x3f == 63, not 64.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's software scan implementation uses a passive dwell time of
(HZ / 5) which means we stay 200ms on each passive channel. Compared
to iwlwifi's hw scan and the old ipw* drivers which use values around
120ms this is quite long.
Reducing the passive dwell time from 200ms to 125ms should save us
something around a second on cards capable of 11a and we should still be
able to catch beacons from most access points (assuming a ~100ms beacon
interval).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't allow users to open debugfs files, because it can cause oopses.
When a user opens some file, driver unlinks it and frees the
corresponding structure, we will dereference freed memory.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't allow users to open debugfs files, because it can cause oopses.
When a user opens some file, driver unlinks it and frees the
corresponding structure, we will dereference freed memory.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We want to see the buffer contents when the error occurs without
needing to set any debug flags.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register locking rework addressed the problem where nic
access was obtained incorrectly when PS is enabled.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes B0 hardware support. Nobody is using it anyway.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch simplifies calibration map by combining the init_calib_map
and periodic_calib_map into one calib_map in struct iwm_conf. Now the
initial calibration map is stored in the lower 16 bits of calib_map
and the periodic calibration map is stored in the higher 16 bits.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch uses netif_rx_ni() over netif_rx() to post buffers to
upper network code because it is always scheduled in a workqueue.
The problem was first observed from a dynamic ticks warning:
"NOHZ: local_softirq_pending ..."
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue when the TX and RX streams are different.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI calibration shouldn't be done when we are not on our home channel.
This is already verified. However, it is racy. Fix this by proper
spin locks.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI is not required when the STA is disconnected. So stop it and enable
ANI for adhoc and monitor mode.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unncessary STATION mode check in ath9k_bss_assoc_info() as
it is called only for STATION mode.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the remaining p54 files to account for the new file organization.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the TX/RX code from p54common.c into a new file txrx.c
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the mac80211 glue code from p54common.c into a new file main.c
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the LMAC Interface specific definitions from p54common.h into a new file lmac.h
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the LED code from p54common.c into a new file led.c
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the firmware i/o code from p54common.c into a new file fwio.c
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the eeprom code from p54common.h into a new file eeprom.h
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copy the eeprom code from p54common.c into a new file eeprom.c
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bufsize and remainder are unsigned. When negative they are wrapped and caught by
the other test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch slightly optimizes p54_rx_data's stack and code size.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Yurovsky reported that the driver forwarded erroneously the
parent device structure instead of the real thing, which of course
led to some dodgy sysfs links (at least?).
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies setup_rxon_timing funcions
of AGN and 3945. HWs differ only in supported maximal
beacon interval. This is reflected in hw_paras.max_beacon_itrvl
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When userspace requests only certain channels to be scanned,
we currently ignore that request entirely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no reason to be assigning txq->swq_id all the
time, once at aggregation setup is sufficient.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each HW supported by iwlwifi is capable of hardware crypto
so drop this flag from hw_params structure.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware may be ready for us to manage it without us trying to prepare
it first. Check if this is the case.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not differentiating quality between legacy and HT
configurations. We change this to consider the differences.
New theory for reporting quality:
At a hardware RSSI of 45 you will be able to use MCS 7 reliably.
At a hardware RSSI of 45 you will be able to use MCS 15 reliably.
At a hardware RSSI of 35 you should be able use 54 Mbps reliably.
MCS 7 is the highets MCS index usable by a 1-stream device.
MCS 15 is the highest MCS index usable by a 2-stream device.
All ath9k devices are either 1-stream or 2-stream.
How many bars you see is derived from the qual reporting.
A more elaborate scheme can be used here but it requires tables
of SNR/throughput for each possible mode used. For the MCS table
you can refer to the wireless wiki:
http://wireless.kernel.org/en/developers/Documentation/ieee80211/802.11n
This should fix this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=13537
Cc: Janath.Peiris@atheros.com
Cc: Matt.Smith@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO driver sets the surpriseremoved flag before calling
lbs_remove_card. With IEEE PS enabled, lbs_remove_card must issue a
command to exit IEEE PS mode, however with that flag set the command
path is blocked and the card is never taken out of IEEE PS mode. This
step is required to ensure that the driver can be reloaded. This patch
moves the setting of surpriseremoved after lbs_remove_card is called.
Tested with V9 firmware by ensuring that IEEE PS is disabled when the
driver is removed. Reloading the driver is not fully tested due to a
separate issue with module reload in the SDIO driver, however this
patch at least leaves the card in a better state when we bring the
driver down.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPI driver does a couple of card cleanup steps in the wrong order on
module removal. If IEEE PS is enabled, this results in the card being
left in IEEE PS mode and subsequent failures to reload the module. The
problem is that the surpriseremoved flag is set before calling
lbs_remove_card, but that function needs to issue a command to exit IEEE
PS mode (the flag blocks the command path). In addition, lbs_stop_card
should be called first because it clears out any pending commands.
Tested on a GSPI device with V9 firmware by confirming that we can
reload the module with or without IEEE PS enabled.
Also fix a warning from the wrong uint format in a printk.
V2: use z modifier, thanks Sebastian.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Libertas currently maintains a copy of the WPA unicast and group keys
when using WPA or WPA2. This copy is checked when deciding whether or
not to return to sleep in IEEE PS mode but the actual copying back to
priv was omitted, which breaks IEEE PS mode with WPA/WPA2 when one
issues commands that require temporarily keeping the device awake.
This patch introduces the omitted copy-back of the keys so that IEEE PS
functions correctly in WPA/WPA2 mode. Thanks to Dan Williams for
clearing up the issue.
V2: fix typo. Also, this has been tested on GSPI and SDIO with V9 firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: Advertise ciphers via WE according to driver capability"
unfortunately broke iwrange -- it used the variable c
that needs to be 0 for the channel list.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this case, only one cipher makes sense, unlike for
connect() where it may be possible to have the card or
driver select.
No changes to mac80211 due to the way the structs are
laid out -- but the loop in net/mac80211/cfg.c will
degrade to just zero or one passes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This addresses the following compile warnings on 64-bit platforms.
drivers/net/wireless/orinoco/scan.c: In function 'orinoco_add_hostscan_results':
drivers/net/wireless/orinoco/scan.c:194: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/orinoco/scan.c:211: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/orinoco/scan.c:211: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible that there are different BSS structs with
the same BSSID, but we cannot authenticate with multiple
of them them because we need the BSSID to be unique for
deauthenticating/disassociating.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function from mac80211 seems generally useful, and
I will need it in cfg80211 soon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the interface is brought down, we need to
reset the auth algorithm because wpa_supplicant
doesn't reset it, and then we fail to use shared
key auth when required later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the userspace SME is in control, we are currently not sending
events, but this means that any userspace applications using wext
or nl80211 to receive events will not know what's going on unless
they can also interpret the nl80211 assoc event. Since we have all
the required code, let the SME follow events from the userspace
SME, this even means that you will be refused to connect() while
the userspace SME is in control and connected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 now always controlled by an external SME,
a lot of code is dead -- SSID, BSSID, channel selection
is always done externally, etc. Additionally, rename
IEEE80211_STA_TKIP_WEP_USED to IEEE80211_STA_DISABLE_11N
and clean up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The automatic auth algorithm issue is now solved in
cfg80211, so mac80211 no longer needs code to try
different algorithms -- just using whatever cfg80211
asked for is good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IEEE80211_STA_TKIP_WEP_USED flag is used internally to
disable HT when WEP or TKIP are used. Now that cfg80211 is
giving us the required information, we can set the flag
appropriately again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By dropping the noise reporting, we can implement
wireless stats in cfg80211. We also make the
handler return NULL if we have no information,
which is possible thanks to the recent wext change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, let's implement that using a very hackish way:
simply mirror the wext API in the cfg80211 API. This
will have to be changed later when we implement proper
bitrate API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements siocsiwap/giwap for WDS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
