Tested with a MX25-based custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Remove !ap test, where ap is guaranteed not-NULL. Found by way of automated
bug report from Alexander Strakh via "Linux Device Drivers Verification
Project (Svace Detector)"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The clock turnaround code still doesn't work for several reasons:
- 'USE_DPLL' flag in 'ap->host->private_data' is never initialized
or updated, so the driver can only set the chip to the DPLL clock
mode, not the PCI mode;
- the driver doesn't serialize access to the channels depending on
the current clock mode like the vendor drivers, so the clock
turnaround is only executed "optionally", not always as it should be;
- the wrong ports are written to when hpt3x2n_set_clock() is called
for the secondary channel;
- hpt3x2n_set_clock() can inadvertently enable the disabled channels
when resetting the channel state machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It appears the size for cs1 is calculated using the wrong resource.
Use the function resource_size to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The mv_init_host will be used to initialize the host hw on resume.
The PCI bar description need to be initialized only once when the
device probed.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The old value (0xbc) in cycles of the IORDY timeout is suitable for
devices with core clock of 166 MHz, but some SoC controllers have
faster core clocks. The new value will make the IORDY timeout large
enough also for all SoC devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
The octeon-ethernet driver shares an mdio bus with the octeon-mgmt
driver. Here we convert the octeon-ethernet driver to use the PHY
Abstraction Layer.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon MGMT Ethernet ports are present in some members of the
Octeon SOC family (cn52XX and cn56XX have them).
The mdio bus connected to the MGMT PHYs is shared with the main
octeon-ethernet driver, we force it to be loaded first by calling
octeon_mdiobus_force_mod_depencency. The platform devices for the
MGMT Ethernet ports are added in
arch/mips/cavium-octeon/octeon-platform.c, and the register
definitions for the ports live in arch/mips/include/asm/octeon/ along
with their ilk.
Although it currently is the only driver in drivers/net/octeon, the
directory was created looking forward to the day that octeon-ethernet
will move there from its current home in drivers/staging.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon SOC has two types of Ethernet ports, each type with its own
driver. However, the PHYs for all the ports are controlled by a
common MDIO bus. Because the mdio driver is not associated with a
particular driver, but is instead a system level resource, we create s
stand-alone driver for it.
As for the driver, we put the register definitions in
arch/mips/include/asm/octeon where most of the other Octeon register
definitions live. This is a platform driver with the platform device
for "mdio-octeon" being registered in the platform startup code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Chris Leech <christopher.leech@intel.com>
Cc: linux-scsi@vger.kernel.org
* 'drm-vmware-staging' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vmwgfx: Add DRM driver for VMware Virtual GPU
drm/vmwgfx: Add svga headers for vmwgfx driver
drm/ttm: Add more driver type enums
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the mach/usb.h with plat/usb.h
Cc: linux-usb-devel@lists.sourceforge.net
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit b72656dbc4 introduced
a bug leading to the w83627hf_find function no longer finding
any chips.
Signed-off-by: Christian Schulte <cs@schulte.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix an off-by-one error in array index + incorrect constants.
Signed-off-by: Christoph Walser <walser@tik.ee.ethz.ch>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a driver for the on-die digital temperature sensor of
VIA's recent CPU models.
[JD: Misc clean-ups.]
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
If the address is set but the device isn't enabled, attempt to enable
it. If it won't work for any reason (resource conflict, no function
enabled) the initial state is restored. The initial state is also
restored on module unloading.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
If an error occurs during probing, there's no point in keeping the
module in memory. Better fail the module loading early to make the
problem more visible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
The I/O area of the SMSC LPC47M1xx chips which we use, gives access to
a lot of registers, some of which are related to fan speed monitoring
and control, but many are not. At the moment, the smsc47m1 driver
requests the whole I/O port range. This could easily result in
resource conflicts with either ACPI or other drivers.
Request only the I/O ports we really use, to prevent such conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Sean Fidler <fidlersean@gmail.com>
This adds a driver for the internal temperature sensor of AMD Family 10h
and 11h CPUs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'hwpoison' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6: (34 commits)
HWPOISON: Remove stray phrase in a comment
HWPOISON: Try to allocate migration page on the same node
HWPOISON: Don't do early filtering if filter is disabled
HWPOISON: Add a madvise() injector for soft page offlining
HWPOISON: Add soft page offline support
HWPOISON: Undefine short-hand macros after use to avoid namespace conflict
HWPOISON: Use new shake_page in memory_failure
HWPOISON: Use correct name for MADV_HWPOISON in documentation
HWPOISON: mention HWPoison in Kconfig entry
HWPOISON: Use get_user_page_fast in hwpoison madvise
HWPOISON: add an interface to switch off/on all the page filters
HWPOISON: add memory cgroup filter
memcg: add accessor to mem_cgroup.css
memcg: rename and export try_get_mem_cgroup_from_page()
HWPOISON: add page flags filter
mm: export stable page flags
HWPOISON: limit hwpoison injector to known page types
HWPOISON: add fs/device filters
HWPOISON: return 0 to indicate success reliably
HWPOISON: make semantics of IGNORED/DELAYED clear
...
Commit d0d26c33b6 broke the driver by
propagating a pointer to the platform_device where a pointer to the
generic device was expected, leading to a spectacular crash...
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (38 commits)
direct I/O fallback sync simplification
ocfs: stop using do_sync_mapping_range
cleanup blockdev_direct_IO locking
make generic_acl slightly more generic
sanitize xattr handler prototypes
libfs: move EXPORT_SYMBOL for d_alloc_name
vfs: force reval of target when following LAST_BIND symlinks (try #7)
ima: limit imbalance msg
Untangling ima mess, part 3: kill dead code in ima
Untangling ima mess, part 2: deal with counters
Untangling ima mess, part 1: alloc_file()
O_TRUNC open shouldn't fail after file truncation
ima: call ima_inode_free ima_inode_free
IMA: clean up the IMA counts updating code
ima: only insert at inode creation time
ima: valid return code from ima_inode_alloc
fs: move get_empty_filp() deffinition to internal.h
Sanitize exec_permission_lite()
Kill cached_lookup() and real_lookup()
Kill path_lookup_open()
...
Trivial conflicts in fs/direct-io.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: rwsem.h need not be included into main.c
PM: Remove unnecessary goto from device_resume_noirq()
PM: Add initcall_debug style timing for suspend/resume
PM: allow for usage_count > 0 in pm_runtime_get()
Due to the merge of processor_start() (declared with __cpuinit) into
processor_add(), a section mismatch warning appears:
WARNING: drivers/built-in.o(.text+0x4d59d): Section mismatch in reference
from the function acpi_processor_add() to the function
.cpuinit.text:acpi_processor_power_init()
...
This patch fixes the warning by declaring processor_add() as __cpuinit
and also declares acpi_processor_add_fs() as __cpuinit as it is only
used in acpi_processor_add().
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
v2->v1:
.improve debug info as suggedted by Bjorn,Kenji
.API is using uuid string as suggested by Alexey
Add an API to execute _OSC. A lot of devices can have this method, so add a
generic API.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
ixgbe: allow tx of pre-formatted vlan tagged packets
ixgbe: Fix 82598 premature copper PHY link indicatation
ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
bcm63xx_enet: fix compilation failure after get_stats_count removal
packet: dont call sleeping functions while holding rcu_read_lock()
tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
ipvs: zero usvc and udest
netfilter: fix crashes in bridge netfilter caused by fragment jumps
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
sky2: leave PCI config space writeable
sky2: print Optima chip name
x25: Update maintainer.
ipvs: fix synchronization on connection close
netfilter: xtables: document minimal required version
drivers/net/bonding/: : use pr_fmt
can: CAN_MCP251X should depend on HAS_DMA
drivers/net/usb: Correct code taking the size of a pointer
drivers/net/cpmac.c: Correct code taking the size of a pointer
drivers/net/sfc: Correct code taking the size of a pointer
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (22 commits)
Input: ALPS - add interleaved protocol support (Dell E6x00 series)
Input: keyboard - don't override beep with a bell
Input: altera_ps2 - fix test of unsigned in altera_ps2_probe()
Input: add mc13783 touchscreen driver
Input: ep93xx_keypad - update driver to new core support
Input: wacom - separate pen from express keys on Graphire
Input: wacom - add defines for data packet report IDs
Input: wacom - add support for new LCD tablets
Input: wacom - add defines for packet lengths of various devices
Input: wacom - ensure the device is initialized properly upon resume
Input: at32psif - do not sleep in atomic context
Input: i8042 - add Gigabyte M1022M to the noloop list
Input: i8042 - allow installing platform filters for incoming data
Input: i8042 - fix locking in interrupt routine
Input: ALPS - do not set REL_X/REL_Y capabilities on the touchpad
Input: document use of input_event() function
Input: sa1111ps2 - annotate probe() and remove() methods
Input: ambakmi - annotate probe() and remove() methods
Input: gscps2 - fix probe() and remove() annotations
Input: altera_ps2 - add annotations to probe and remove methods
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix r100->r500 CS checker for compressed textures. (v2)
drm/radeon/kms: allow for texture tiling
drm/radeon/kms: init pm on all chipsets
drm/radeon/kms: HDMI support for R600 KMS
drm/radeon/kms: make sure mc is initialized before mapping blit bo
drm/radeon/kms: Return to userspace on ERESTARTSYS
drm/radeon/gem: don't leak a gem object if reserve fails on get tiling (v2)
drm/radeon/kms: don't report allocate failure on ERESTARTSYS
drm/radeon/kms: Check if bo we got from ttm are radeon object or not
drm/radeon/kms: If no placement is supplied fallback to system
drm/ttm: Fix memory type manager debug information printing
drm/ttm: Fix printk format & compute bo->mem.size at bo initialization
drm/ttm: Fix potential ttm_mem_evict_first races.
drm/ttm: Delayed delete fixes.
drm/ttm: fix two bugs in new placement routines.
drm/ttm: fix incorrect logic in ttm_bo_io path
drm/nouveau: remove use of -ERESTART
nouveau: Fix endianness with new context program loader
drm/nouveau: fix build with CONFIG_AGP=n
drm/nouveau: fix ch7006 build
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
ppc440spe-adma: adds updated ppc440spe adma driver
iop-adma.c: use resource_size()
dmaengine: clarify the meaning of the DMA_CTRL_ACK flag
sh: stylistic improvements for the DMA driver
dmaengine: fix dmatest to verify minimum transfer length and test buffer size
sh: DMA driver has to specify its alignment requirements
Add COH 901 318 DMA block driver v5
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: Fixup last users of irq_chip->typename
parisc: convert /proc/pdc/{lcd,led} to seq_file
parisc: Convert BUG() to use unreachable()
parisc: Replace old style lock init in smp.c
parisc: use sort() instead of home-made implementation (v2)
parisc: add CALLER_ADDR{0-6} macros
parisc: remove unused IRQSTAT_SIRQ_PEND and IRQSTAT_SZ defines
parisc: remove duplicated #include
* git://git.infradead.org/iommu-2.6:
implement early_io{re,un}map for ia64
Revert "Intel IOMMU: Avoid memory allocation failures in dma map api calls"
intel-iommu: ignore page table validation in pass through mode
intel-iommu: Fix oops with intel_iommu=igfx_off
intel-iommu: Check for an RMRR which ends before it starts.
intel-iommu: Apply BIOS sanity checks for interrupt remapping too.
intel-iommu: Detect DMAR in hyperspace at probe time.
dmar: Fix build failure without NUMA, warn on bogus RHSA tables and don't abort
iommu: Allocate dma-remapping structures using numa locality info
intr_remap: Allocate intr-remapping table using numa locality info
dmar: Allocate queued invalidation structure using numa locality info
dmar: support for parsing Remapping Hardware Static Affinity structure
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (116 commits)
V4L/DVB (13698): pms: replace asm/uaccess.h to linux/uaccess.h
V4L/DVB (13690): radio/si470x: #include <sched.h>
V4L/DVB (13688): au8522: modify the attributes of local filter coefficients
V4L/DVB (13687): cx231xx: use NULL when pointer is needed
V4L/DVB: Davinci VPFE Capture: remove unused #include <linux/version.h>
V4L/DVB (13685): Correct code taking the size of a pointer
V4L/DVB (13684): Fix some cut-and-paste noise in dib0090.h
V4L/DVB (13683): sanio-ms: clean up init, exit and id_table
V4L/DVB (13682): dib8000: make some constant static
V4L/DVB: lgs8gxx: Use shifts rather than multiply/divide when possible
V4L/DVB (13680b): DocBook/media: create links for included sources
V4L/DVB (13680a): DocBook/media: copy images after building HTML
V4L/DVB (13678): Add support for yet another DvbWorld, TeVii and Prof USB devices
V4L/DVB (13676): configurable IRQ mode on NetUP Dual DVB-S2 CI; IRQ from CAM processing (CI interface works faster)
V4L/DVB (13674): stv090x: Add DiSEqC envelope mode
V4L/DVB (13673): lnbp21: Implement 22 kHz tone control
V4L/DVB (13671): sh_mobile_ceu_camera: Remove frame size page alignment
V4L/DVB (13670): soc-camera: Add mt9t112 camera driver
V4L/DVB (13669): tw9910: Add sync polarity support
V4L/DVB (13668): tw9910: remove cropping
...
Now depends on BACKLIGHT_CLASS_DEVICE.
Driver will return an error if it can't get actual backlight value
Fix remapping of brightness keys when backlight is not controlled by ACPI.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Len Brown <len.brown@intel.com>
There should be less code duplication with usage of gotos
Driver won't load if there's no hardware to control
Safer error handling at input driver allocation
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver serves backlight (including switching) and volume up/down
keys for MSI machines providing a specific wmi interface:
551A1F84-FBDD-4125-91DB-3EA8F44F1D45
B6F3EEF2-3D2F-49DC-9DE3-85BCE18C62F2
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Carlos Corbacho <carlos@strangeworlds.co.uk>
CC: Matthew Garrett <mjg59@srcf.ucam.org>
Tested-by: Matt Chen <machen@novell.com>
Reviewed-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Len Brown <len.brown@intel.com>
* don't reinvent the wheels, please - open_bdev_exclusive() is there
for purpose
* both open_by_devnum() and open_bdev_exclusive() return ERR_PTR(...)
upon error, not NULL
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch adds support for the ACPI events generated by the RFKill
switch on modern Toshiba laptops, and re-enables the Bluetooth USB
device when the switch is flipped back to the 'on' position.
The RFKill switch brute force pulls out the USB device when flipped to
'off', but it doesn't automatically re-enable it. Without this driver,
the Bluetooth is gone until after a reboot on my Portege R500.
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Although reporting of benign GART TLB errors is disabled in
__mcheck_cpu_apply_quirks, those are still being logged, and, as a
result, trip up amd64_edac. Pull up reporting check so that machines
with loaded edac module bail out early and don't spit fragments into
dmesg.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
GRU Message queue instructions are used to deliver messages to other SSIs
within the numalink domain. In most cases, a single GRU mesq instruction
will deliver both the message AND an interrupt to notify the other SSI
that a messsage is present. In some cases, however, the interrupt must be
sent explicitly.
To improve resilency, the GRU driver should send these explicit interrupts
using the GRU to write the remote chipset register. Current code sends
the interrupt using a cpu instruction to write the chipset register.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the version number of the GRU driver.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the TLB dropin statistics kept for each GRU context. Count TLB
dropins separate from the misses - some misses do not result in a TLB
dropin. Some of the diagnostics need both counts.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a race where an interrupt could be received for a GRU context that has
been deallocated.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for hugepages. Easier than I originally thought.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the assignment of GRU contexts used for kernel functions. If
a sleep occurs on the wait for a semaphore, the thread could switch cpus
and allocate resources on the wrong blade.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a few new definitions for chipset MMR field names. This matches rev
0.7 of the hardware spec.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify the code that checks for correct assignment of GRU contexts to
users.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove a stray local_irq_enable() in the GRU TLB dropin code.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use symbol names instead of numbers for error return values for the vtop
functions.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a GRU driver bug converting a CBR address to the context that contains
the CBR. The conversion is rarely done so performance does not matter.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add anticipatory TLB dropins for GRU TLB misses that occur on BCOPY
instructions that copy large amounts of data.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Explicitly set GRU instructions to "ACTIVE". This eliminates the need for
barriers that would have been necessary to prevent reading the instruction
"status" field before the GRU had actually started the instruction.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the GRU irq allocate/free functions to use the latest upstream
infrastructure.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix several bugs related to prefetch, ordering & speculation:
- GRU cch_allocate() instruction causes cacheable memory
to be created. Add a barriers to prevent speculation
from prefetching data before it exists.
- Add memory barriers before cache-flush instructions to ensure
that previously stored data is included in the line flushed to memory.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug caused by failure to allocate a GRU gts structure. The old code
failed to handle the case where the vma was invalid.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve existing driver self-tests. Add a new debugging test to the SGI
GRU driver for verifying the global GRU copy function.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a debug option to the SGI GRU driver for flushing GRU cache lines from
memory. In theory this is not needed but it is useful for debugging.
This has no use by end users.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under some conditions, mmu_notifier_register() will fail to register a
mmu_notifier. Fix the GRU driver to correctly handle these failures.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Increase the maximum address supported by the SGI GRU driver to a full 64
bits. Note that GRU addresses are not always the same as socket virtual
addresses. Sockets may not necessarily support the full 64 bits.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve error messages for malfunctioning GRUs. Identify the type of
instruction that is failing.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in module unload. Previous code was not correctly deleting the
files in /proc.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch builds on the infrastructure introduced in the patches that
allow user specification of GRU blades & chiplets for context allocation.
This patch simplifies the algorithms for migrating GRU contexts between
blades.
No new functionality is introduced.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to the GRU driver to allow users to specify the blade &
chiplet for allocation of GRU contexts. Add new statistics for context
loading/unloading/retargeting. Also deleted a few GRU stats that were no
longer being unused.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add table & user request infrastructure that is needed to allow users to
specify the blade and chiplet for allocation of GRU contexts. Use of this
information is in a subsequent patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not use alloc_pages_exact_node() to allocate GRU tables. If a blade
has no local memory, nid will be -1. Use alloc_pages_node() instead.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TLB dropins require updates to the CBR instruction istatus field. This is
needed to resolve race conditions in the chip.
The code currently uses the user address of the CBR. This works but opens
up additional endcases related to stealing of contexts and accessing the
CBR from tasks that do not have access to the user address space. (Some
of this non-user task access is debug code that is not currently being
pushed to the community).
User CBRs are also directly accessible using the kernel mapping of the
CBR. Change the TLB dropin code to use the the kernel mapping of the CBR.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add comments from previous code reviews. The comments help explain some
of the more esoteric aspects of the driver.
Move a free() to the other side of an unlock.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the GRU initialization code to initialize based on blade topology
instead of node topology. The result is the same but blade-based
initialization is cleaner.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the UV xpc code is passing nid to the gru_create_message_queue
instead of nasid as it expects.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was a difficult bug to trip. XPC was in the middle of sending an
acknowledgement for a received message.
In xpc_received_payload_uv():
.
ret = xpc_send_gru_msg(ch->sn.uv.cached_notify_gru_mq_desc, msg,
sizeof(struct xpc_notify_mq_msghdr_uv));
if (ret != xpSuccess)
XPC_DEACTIVATE_PARTITION(&xpc_partitions[ch->partid], ret);
msg->hdr.msg_slot_number += ch->remote_nentries;
at the point in xpc_send_gru_msg() where the hardware has dispatched the
acknowledgement, the remote side is able to reuse the message structure
and send a message with a different slot number. This problem is made
worse by interrupts.
The adjustment of msg_slot_number and the BUG_ON in
xpc_handle_notify_mq_msg_uv() which verifies the msg_slot_number is
consistent are only used for debug purposes. Since a fix for this that
preserves the debug functionality would either have to infringe upon the
payload or allocate another structure just for debug, I decided to remove
it entirely.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many times while the initial connection is being made, the contacted
partition will send back both the ACTIVATING and the ACTIVE
remote_act_state changes in very close succescion. The 1/4 second delay
in the make first contact loop is large enough to nearly always miss the
ACTIVATING state change.
Since either state indicates the remote partition has acknowledged our
state change, accept either.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Under heavy load conditions, our set of xpc messages may become exhausted.
The code handles this correctly with the exception of the management code
which hits a NULL pointer dereference.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UV BIOS has moved the location of some of their pointers to the
"partition reserved page" from memory into a uv hub MMR. The GRU does not
support bcopy operations from MMR space so we need to special case the MMR
addresses using VLOAD operations.
Additionally, the BIOS call for registering a message queue watchlist has
removed the 'blade' value and eliminated the structure that was being
passed in. This is also reflected in this patch.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The BIOS has decided to store a pointer to the partition reserved page in
a scratch MMR. The GRU is only able to read an MMR using a vload
instruction. The gru_read_gpa() function will implemented.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide an SGI SN2/UV agnositic method for converting a global physical
address into a socket physical address.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for 6 ranks per channel to the i5100 chipset. I have tested
the patch as far as possible with correctible errors and things appear
good. The DIMM mapping is correct for our board, but boards may differ.
Signed-off-by: Nils Carlson <nils.carlson@ludd.ltu.se>
Acked-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Addscrubbing to the i5100 chipset. The i5100 chipset only supports one
scrubbing rate, which is not constant but dependent on memory load. The
rate returned by this driver is an estimate based on some experimentation,
but is substantially closer to the truth than the speed supplied in the
documentation.
Also, scrubbing is done once, and then a done-bit is set. This means that
to accomplish continuous scrubbing a re-enabling mechanism must be used.
I have created the simplest possible such mechanism in the form of a
work-queue which will check every five minutes. This interval is quite
arbitrary but should be sufficient for all sizes of system memory.
Signed-off-by: Nils Carlson <nils.carlson@ludd.ltu.se>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i5100 driver uses the word controller instead of channel in a lot of
places, this is simply a cleanup of the patch.
Signed-off-by: Nils Carlson <nils.carlson@ludd.ltu.se>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KCS_IDLE and KCS_IDLE state have the same value, but in this function the
constants ending in _STATE are compared to the state variable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Core Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert code away from ->read_proc/->write_proc interfaces. Switch to
proc_create()/proc_create_data() which make addition of proc entries
reliable wrt NULL ->proc_fops, NULL ->data and so on.
Problem with ->read_proc et al is described here commit
786d7e1612 "Fix rmmod/read/write races in
/proc entries"
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Adam Belay <abelay@mit.edu>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intelfb driver sets color map depending on currently active pipe.
However, if an LVDS display is attached (like in laptop) the active pipe
variable is never set. The default value is PIPE_A and can be wrong. Set
up the pipe variable during driver initialization after hardware state was
read.
Also, the detection of the active display (and hence the pipe) is wrong.
The pipes are assigned to so called planes. Both pipes are always enabled
on my laptop but only one plane is enabled (the plane A for the CRT or the
plane B for the LVDS). Change active pipe detection code to take into
account a status of the plane assigned to each pipe.
The problem is visible in the 8 bpp mode if colors above 15 are used. The
first 16 color entries are displayed correctly.
The graphics chip description is here (G45 vol. 3):
http://intellinuxgraphics.org/documentation.html
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13285
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Michal Suchanek <hramrach@centrum.cz>
Cc: Dean Menezes <samanddeanus@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A humble attempt to simplify the coding style to improve readability
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Regression caused in 2.6.23 and then despite repeated requests never fixed
or dealt with (Petr promised to sort it in 2008 but seems to have
forgotten).
Enough is enough - remove the problem line that was added. If it upsets
someone they've had two years to deal with it and at the very least it'll
rattle their cage and wake them up.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9709
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Damon <account@bugzilla.kernel.org.juxtaposition.net>
Tested-by: Ruud van Melick <rvm1974@raketnet.nl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul A. Clarke <pc@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement frame buffer blank operation feature for DA8xx/OMAP-L1xx driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suspend/resume support DA8xx/OMAP-L1xx frame buffer driver. This feature
has been tested on DA850/OMAP-L138 EVM. For the purpose of testing, the
patch series[1] which adds suspend support for DA850/OMAP-L138 SoC was
applied.
[1] http://patchwork.kernel.org/patch/60260/
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a helper function to enable raster. Also add one member in the
private data structure to track the current blank status, another function
pointer which takes in the platform specific callback function to control
panel power.
These updates will help in adding suspend/resume and frame buffer blank
operation features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixed a typo: missing *. This would lead to a kernel oops if the kernel
was compiled without support for the /proc file system.
Found with a static checker. Compile tested.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Scott Fang <ScottFang@viatech.com.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch provides the acceleration entry points for the SM501
framebuffer driver.
This patch provides the sync, copyarea and fillrect entry points, using
the SM501's 2D acceleration engine to perform the operations in-chip
rather than across the bus.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the old style use of <asm/io.h> by replacing it with <linux/io.h>.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: Vincent Sanders <vince@simtec.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several places in the SM501 fb driver that could do with using
resource_size() to calculate the size of a resource.
Also fix a bug where request_mem_region() is being passed one too few
bytes when requesting the register memory region, which was causing the
following in /proc/iomem:
13e80000-13e8ffff : sm501-fb.0
13e80000-13e8fffe : sm501-fb
fixed, this reads:
13e80000-13e8ffff : sm501-fb.0
13e80000-13e8ffff : sm501-fb
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: Vincent Sanders <vince@simtec.co.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox has found that the i810fb function "uses a whopping 2.5K of stack".
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GRUB folks requested copyright/license info for lxfb.h, so here it is.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add cpufreq support for DA8xx/OMAP-L1xx frame buffer driver
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock divider value can be calculated from the pixel clock value for
the panel. This gives more flexiblity to the driver to change the divider
value on the fly as in the case of cpufreq feature- support for which will
be added shortly.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the NULL test on fbi is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add check if palette register number is in correct range for few drivers
which miss it. The regno value comes indirectly from user space.
Two drivers has converted check from BUG_ON() macro to just return an
error (non-zero value).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel has simple_strtol() implementation which could be used as atoi().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TV_PALN bit was tested twice, replace one by TV_PALM.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The height/width framebuffer members need to be set in millimeters so that
software can do proper scaling.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD commands DMA/timers as well as PPI which we need to save/restore.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers may use gpiolib sysfs as part of their public user space
interface. The GPIO number and polarity might change from board to
board. The gpio_export_link() call can be used to hide the GPIO number
from user space. Add support for also hiding the GPIO line polarity
changes from user space.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Timberdale FPGA found on the Intel Atom board
Russellville.
The GPIO driver also has an IRQ-chip to support interrupts on the pins.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrong test was used, gpio is unsigned and it had an off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All callsites of x1205_set_datetime() want the date to be set as well, so
remove the flag parameter and set it unconditionally.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible to have RTC irq shared with other device (e.g.
mpc8349e-mitx board shares ds1339 irq with phy one). Handle this in
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This switches __raw_[read|write]l() for plain [read|write]l in the PL031
RTC driver. The sister driver for PL030 use the simple accessors as most
PrimeCell drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds basic support for Texas Instruments BQ32000 I2C RTC. Only
time reading/writing is implemented. Advanced features, such as trickle
charger and crystal calibration are not supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-omap driver currently assumes that the rtc's registers are at a
fixed address and already mapped into virtual memory space. Remove those
assumptions so the same driver can be used for similar devices that reside
at different physical addresses (e.g., TI's DA8xx/OMAP-L13x SoC's).
Also allow the possibility for the timer and alarm interrupts to use the
same IRQ.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver provides support for the RTC part integrated into the
Freescale MC13783 PMIC and bases on patch created earlier by Sascha
Hauer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the Alarm support, this mode enabled when adding
IORESOURCE_IRQ to the platform device resources.
The patch also enables the wakeup mode, so the wakealarm sysfs file (under
/sys/class/rtc/rtcX/) can be used to configure the alarm clock.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add setting and clearing of the "pending" flag of the RTC alarm. The
semantics follow the UEFI specification 2.2 available at
http://www.uefi.org/specs/, i.e., the "pending" flag is cleared by
disabling the alarm, but not by any other condition (such as the passing
of time, a successful wakeup, or setting of a new alarm.)
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we've removed the BKL here, let's explicitly set llseek to
no_llseek since the default llseek is not used here.
The default_llseek function still contains the BKL. When we are auditing
code to see if we can remove the BKL, this is one of the hidden
considerations we need to take into account. i.e., is there
syncronization between code that has the BKL and llseek.
At the same time we remove the BKL it would be a good idea to do indicate
when no llseek function is required, so we don't have to revisit this code
again, when we are trying to determine if we can remove the BKL from the
default_llseek.
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The to_platform_device macro itself uses container_of macro. Nested use
of container_of macro causes following sparse warnings:
rtc-ds1553.c:259:3: warning: symbol '__mptr' shadows an earlier one
rtc-ds1553.c:259:3: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
