The ieee80211_queue_stopped() expects hw queue
number but it was given raw WMM AC number instead.
This could cause frame drops and problems with
traffic in some cases - most notably if driver
doesn't map AC numbers to queue numbers 1:1 and
uses ieee80211_stop_queues() and
ieee80211_wake_queue() only without ever calling
ieee80211_wake_queues().
On ath10k it was possible to hit this problem in
the following case:
1. wlan0 uses queue 0
(ath10k maps queues per vif)
2. offchannel uses queue 15
3. queues 1-14 are unused
4. ieee80211_stop_queues()
5. ieee80211_wake_queue(q=0)
6. ieee80211_wake_queue(q=15)
(other queues are not woken up because both
driver and mac80211 know other queues are
unused)
7. ieee80211_rx_h_mesh_fwding()
8. ieee80211_select_queue_80211() returns 2
9. ieee80211_queue_stopped(q=2) returns true
10. frame is dropped (oops!)
Fixes: d3c1597b8d ("mac80211: fix forwarded mesh frame queue mapping")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver can access the queue simultanously
while mac80211 tears down the interface. Without
spinlock protection this could lead to corrupting
sk_buff_head and subsequently to an invalid
pointer dereference.
Fixes: ba8c3d6f16 ("mac80211: add an intermediate software queue implementation")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unnecessory "if" statement and club it with previos "if" block.
Signed-off-by: Sunil Shahu <shshahu@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In VHT, the specification allows to limit the number of
MSDUs in an A-MSDU in the Extended Capabilities IE. There
is also a limitation on the byte size in the VHT IE.
In HT, the only limitation is on the byte size.
Parse the capabilities from the peer and make them
available to the driver.
In HT, there is another limitation when a BA agreement
is active: the byte size can't be greater than 4095.
This is not enforced here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The minimum chandef bandwidth calculation was done only in case
a new station was inserted (or when an existing station was removed).
However, it is possible that stations are inserted before they are
associated, e.g., when FULL_AP_CLIENT_STATE is supported and user
space adds stations unassociated.
Fix this by calling ieee80211_recalc_min_chandef() whenever
a station transitions in/out the associated state, and only
consider station marked as associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers offload some frames internally (e.g.
AddBa). Reporting such frames to mac80211 would
only confuse MLME. However it would be useful to
be able to pass such frames to monitor interfaces
for sniffing purposes, e.g. when running AP +
monitor.
To do that allow drivers to tell mac80211 whether
a given frame should be:
- processed but not delivered to any monitor vif
- not processed but delievered to monitor vifs
only
Signed-off-by: Grzegorz Bajorski <grzegorz.bajorski@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable driver to manage the reordering logic itself.
This is needed for example for the iwlwifi driver that
will support hardware assisted reordering.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change from cur_tp to the function
minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the
current throughput. For example in minstrel_ht the correct
conversion between them would be:
mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..).
This factor 10 must also be included in the calculation of
minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to
return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing
algorithms like B.A.T.M.A.N. V will make incorrect decision based on these
values. Its kernel based implementation expects expected_throughput always
to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps].
The same requirement has iw or olsrdv2's nl80211 based statistics module
which retrieve the same data via NL80211_STA_INFO_TX_BITRATE.
Cc: stable@vger.kernel.org
Fixes: 6a27b2c40b ("mac80211: restructure per-rate throughput calculation into function")
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patch fixes this splat
BUG: KASAN: slab-out-of-bounds in minstrel_ht_update_stats.isra.7+0x6e1/0x9e0
[mac80211] at addr ffff8800cee640f4 Read of size 4 by task swapper/3/0
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiNyJhSaVnE35qS6UCGaSb2Dx1_i5HcRavuOX14oTz2P+w@mail.gmail.com
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
Use kzalloc instead of kmalloc for struct tid_ampdu_rx to
initialize the "removed" field (all others are initialized
manually). That fixes:
UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29
load of value 2 is not a valid value for type '_Bool'
CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265
Workqueue: phy0 rt2x00usb_work_rxdone
0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007
ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500
ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032
Call Trace:
[<ffffffff8181d866>] dump_stack+0x45/0x5f
[<ffffffff8188422d>] ubsan_epilogue+0xd/0x40
[<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70
[<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730
[<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00
[<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750
[<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990
While at it, convert to use sizeof(*tid_agg_rx) instead.
Fixes: 788211d81b ("mac80211: fix RX A-MPDU session reorder timer deletion")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[reword commit message, use sizeof(*tid_agg_rx)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.
This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With upcoming CONFIG_UBSAN the following BUILD_BUG_ON in
net/mac80211/debugfs.c starts to trigger:
BUILD_BUG_ON(hw_flag_names[NUM_IEEE80211_HW_FLAGS] != (void *)0x1);
It seems, that compiler instrumentation causes some code
deoptimizations. Because of that GCC is not being able to resolve
condition in BUILD_BUG_ON() at compile time.
We could make size of hw_flag_names array unspecified and replace the
condition in BUILD_BUG_ON() with following:
ARRAY_SIZE(hw_flag_names) != NUM_IEEE80211_HW_FLAGS
That will have the same effect as before (adding new flag without
updating array will trigger build failure) except it doesn't fail with
CONFIG_UBSAN. As a bonus this patch slightly decreases size of
hw_flag_names array.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 does not inform the driver of the window
size when starting an RX aggregation session.
To enable managing the reorder buffer in the driver or hardware
the window size is needed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option for driver to check for packet duplication
by itself.
This is needed for example by the iwlwifi driver which
parallelizes the RX path and does the duplication check
per queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-bufferable MMPDUs are sent out to STAs even while in PS mode
(for example probe responses). Applying filtered frame handling for
these doesn't seem to make much sense and will only create more
air utilization when the STA wakes up. Hence, apply filtered frame
handling only for bufferable MMPDUs.
Discovered while testing an old VOIP phone that started probing
for APs while in PS mode. The mac80211/ath9k AP where the STA is
associated would reply with a probe response but the phone sometimes
moved to a new channel already and couldn't ack the probe response
anymore. In that case mac80211 applied filtered frame handling
for the un-acked probe response.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hw restart, mac80211 might try to reconfigure already
stopped sched scan, if ieee80211_sched_scan_stopped_work()
wasn't scheduled yet.
This in turn will keep the device driver with scheduled scan
configured, while both mac80211 and cfg80211 will clear
their sched scan state once the work is scheduled.
Fix it by ignoring ieee80211_sched_scan_stopped() calls
while in hw restart, and flush the work before starting
the reconfiguration.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit below broken PS-Poll handling. In case the driver
has no frames buffered, driver_release_tids will be 0, but
calling find_highest_prio_tid() with 0 as a parameter is
not a good idea:
fls(0) - 1 = -1.
This bug caused mac80211 to think that frames were buffered
in the driver which in turn was confused because mac80211
was asking to release frames that were not reported to
exist.
On iwlwifi, this led to the WARNING below:
WARNING: CPU: 0 PID: 11230 at drivers/net/wireless/intel/iwlwifi/mvm/sta.c:1733 iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]()
ffffffffc0627c60 ffff8800069b7648 ffffffff81888913 0000000000000000
0000000000000000 ffff8800069b7688 ffffffff81089d6a ffff8800069b7678
0000000000000001 ffff88003b35abf0 ffff88000698b128 ffff8800069b76d4
Call Trace:
[<ffffffff81888913>] dump_stack+0x4c/0x65
[<ffffffff81089d6a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff81089e5a>] warn_slowpath_null+0x1a/0x20
[<ffffffffc05f36bf>] iwl_mvm_sta_modify_sleep_tx_count+0x2af/0x320 [iwlmvm]
[<ffffffffc05dae41>] iwl_mvm_mac_release_buffered_frames+0x31/0x40 [iwlmvm]
[<ffffffffc045d8b6>] ieee80211_sta_ps_deliver_response+0x6e6/0xd80 [mac80211]
[<ffffffffc0461296>] ieee80211_sta_ps_deliver_poll_response+0x26/0x30 [mac80211]
[<ffffffffc048f743>] ieee80211_rx_handlers+0xa83/0x2900 [mac80211]
[<ffffffffc04917ad>] ieee80211_prepare_and_rx_handle+0x1ed/0xa70 [mac80211]
[<ffffffffc045e3d5>] ? sta_info_get_bss+0x5/0x4a0 [mac80211]
[<ffffffffc04925b6>] ieee80211_rx_napi+0x586/0xcd0 [mac80211]
[<ffffffffc05eaa3e>] iwl_mvm_rx_rx_mpdu+0x59e/0xc60 [iwlmvm]
Fixes: 0ead2510f8 ("mac80211: allow the driver to send EOSP when needed")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On reconfig, in case of sched_scan_req->n_scan_plans > 1,
local->sched_scan_req was never cleared, although
cfg80211_sched_scan_stopped_rtnl() was called, resulting
in local->sched_scan_req holding a stale and preventing
further scheduled scan requests.
Clear it explicitly in this case.
Fixes: 42a7e82c6792 ("mac80211: Do not restart scheduled scan if multiple scan plans are set")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Defer ROC requests during hw restart, as the driver
might not be fully configured in this stage (e.g.
channel contexts were not added yet)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan's previous commit 1b894521e6 ("mac80211: handle HW
ROC expired properly") neglected to take into account that
hw_begun was now always set in the software implementation
as well as the offloaded case.
Fix hw_begun to only apply to the offloaded case to make
the check in Ilan's commit safe and correct.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current (new) code recalculates the new work timeout
for software remain-on-channel whenever any item started.
In two of the callers of ieee80211_handle_roc_started(),
this is completely pointless since they're for hardware
and will skip the recalculation entirely; it's necessary
only in the case of having just added a new item to the
list, as in the last remaining case the recalculation had
just been done.
This last case, however, is also problematic - if one of
the items on the list actually expires during the recalc
the list iteration outside becomes corrupted and crashes.
Fix this by moving the recalculation to the only place
where it's required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP is advertising limited TX power, the message can be
printed over and over again. Suppress it when the power level
isn't changing.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reprogramming, mac80211 currently first adds all the channel
contexts, then binds them to the vifs and then goes to reconfigure
all the interfaces. Drivers might, perhaps implicitly, rely on the
operation order for certain things that typically happen within a
single function elsewhere in mac80211. To avoid problems with that,
reorder the code in mac80211's restart/reprogramming to work fully
within the interface loop so that the order of operations is like
in normal operation.
For iwlwifi, this fixes a firmware crash when reprogramming with an
AP/GO interface active.
Reported-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reconfiguration during resume fails while a scan is pending
for completion work, that work will never run, and the scan will
be stuck forever. Factor out the code to recover this and call it
also in ieee80211_handle_reconfig_failure().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HW ROC, when the driver reports that the ROC expired,
it is not sufficient to purge the ROCs based on the remaining
time, as it possible that the device finished the ROC session
before the actual requested duration.
To handle such cases, in case of ROC expired notification from
the driver, complete all the ROCs which are marked with hw_begun,
regardless of the remaining duration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When cancelling, you can cancel "any" (first in list) mgmt-tx
or remain-on-channel operation by using the value 0 for the
cookie along with the *opposite* operation, i.e.
* cancel the first mgmt-tx by cancelling roc with 0 cookie
* cancel the first roc by cancelling mgmt-tx with 0 cookie
This isn't really that bad since userspace should only pass
cookies that we gave it, but could lead to hard-to-debug
issues so better prevent it and reject zero values since we
never hand those out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While it was possible to create an IBSS with 80+80 MHz channel, joining
such an IBSS resulted in falling back to 20 MHz channel with VHT
disabled due to a missing switch case for 80+80.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni found a bug in the remain-on-channel logic: when a short item
is queued, a long item is combined with it extending the original
one, and then the long item is deleted, the timeout doesn't go back
to the short one, and the short item ends up taking a long time. In
this case, this showed as blocking scan when running two test cases
back to back - the scan from the second was delayed even though all
the remain-on-channel items should long have been gone.
Fixing this with the current data structures turns out to be a bit
complicated, we just remove the long item from the dependents list
right now and don't recalculate the timeouts.
There's a somewhat similar bug where we delete the short item and
all the dependents go with it; to fix this we'd have to move them
from the dependents to the real list.
Instead of trying to do that, rewrite the code to not have all this
complexity in the data structures: use a single list and allow more
than one entry in it being marked as started. This makes the code a
bit more complex, the worker needs to understand that it might need
to just remove one of the started items, while keeping the device
off-channel, but that's not more complicated than the nested data
structures.
This then fixes both issues described, and makes it easier to also
limit the overall off-channel time when combining.
TODO: as before, with hardware remain-on-channel, deleting an item
after combining results in cancelling them all - we can keep track
of the time elapsed and only cancel after that to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the cookie is assigned inside ieee80211_make_ack_skb()
now, we no longer need to return the ack_skb as the cookie
and can simplify the function's return and the callers. Also
rename it to ieee80211_attach_ack_skb() to more accurately
reflect its purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is quite a bit of code that logically depends here since
it has to deal with all the remain-on-channel logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a mgmt-tx operation is aborted before it runs, the wrong
cookie is reported back to userspace, and the ack_skb gets
leaked since the frame is freed directly instead of freeing
it using ieee80211_free_txskb(). Fix that.
Fixes: 3b79af973c ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If some code stops the queues more times than having started
(for when refcounting is used), warn on and reset the counter
to 0 to avoid blocking forever.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When freeing the TX skb for an off-channel TX, use the correct
API to also free the ACK skb that might have been allocated.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a new station is added to AP/GO interfaces the default behaviour
is for it to be added authenticated and associated, due to backwards
compatibility. To prevent that, the driver must be able to do that
(setting the NL80211_FEATURE_FULL_AP_CLIENT_STATE feature flag) and
userspace must set the flag mask to auth|assoc and clear the set.
Handle this quirk in the API entirely in nl80211, and always push the
full flags to the drivers. NL80211_FEATURE_FULL_AP_CLIENT_STATE is
still required for userspace to be allowed to set the mask including
those bits, but after checking that add both flags to the mask and
set in case userspace didn't set them otherwise.
This obsoletes the mac80211 code handling this difference, no other
driver is currently using these flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds implementation for abort scan in mac80211.
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[adjust to wdev change in previous patch and clean up code a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add ieee80211_iter_keys_rcu() to iterate over uploaded
keys in atomic context (when rcu is locked)
The station removal code removes the keys only after
calling synchronize_net(), so it's not safe to iterate
the keys at this point (and postponing the actual key
deletion with call_rcu() might result in some
badly-ordered ops calls).
Add a flag to indicate a station is being removed,
and skip the configured keys if it's set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can happen when the driver needs to send less frames
than expected and then needs to close the SP.
Mac80211 still needs to set the more_data properly based
on its buffer state (ps_tx_buffer and buffered frames on
other TIDs).
To that end, refactor the code that delivers frames upon
uAPSD trigger frames to be able to get only the more_data
bit without actually delivering those frames in case the
driver is just asking to set a NDP with EOSP and MORE_DATA
bit properly set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really should never happen except very early in the process
of bringing up a new driver, at which point you'll have to add
more debugging in the driver and this string isn't useful. Remove
it and save some size (when it's even compiled in.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no point in printing the mpath pointer since it can't
be used for anything - print the MAC address instead (like in
the forwarding case.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices or drivers cannot deal with having the same station
address for different virtual interfaces, say as a client to two
virtual AP interfaces. Rather than requiring each driver with a
limitation like that to enforce it, add a hardware flag for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the last change here, I neglected to update the cookie in one code
path: when a mgmt-tx has no real cookie sent to userspace as it doesn't
wait for a response, but is off-channel. The original code used the SKB
pointer as the cookie and always assigned the cookie to the TX SKB in
ieee80211_start_roc_work(), but my change turned this around and made
the code rely on a valid cookie being passed in.
Unfortunately, the off-channel no-wait TX path wasn't assigning one at
all, resulting in an uninitialized stack value being used. This wasn't
handed back to userspace as a cookie (since in the no-wait case there
isn't a cookie), but it was tested for non-zero to distinguish between
mgmt-tx and off-channel.
Fix this by assigning a dummy non-zero cookie unconditionally, and get
rid of a misleading comment and some dead code while at it. I'll clean
up the ACK SKB handling separately later.
Fixes: 3b79af973c ("mac80211: stop using pointers as userspace cookies")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
DFS channels should not be actively scanned as we can't be sure
if we are allowed or not.
If the current channel is in the DFS band, active scan might be
performed after CSA, but we have no guarantee about other channels,
therefore it is safer to prevent active scanning at all.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Interfaces are being initialized (setup) on addition,
and torn down on removal.
However, p2p device is being torn down when stopped,
resulting in the next p2p start operation being done
on uninitialized interface.
Solve it by calling ieee80211_teardown_sdata() only
on interface removal (for the non-netdev case).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[squashed in fix to call teardown after unregister]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertising reordering window in ADDBA less than 64 can crash some APs,
an example is LinkSys WRT120N (with FW v1.0.07 build 002 Jun 18 2012).
On the other hand, a driver may need to limit Tx A-MPDU size for its own
reasons, like specific HW limitations.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.
Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.
This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.
Cc: stable@vger.kernel.org
Fixes: eb2b9311fd ("mac80211: mesh path table implementation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, this feature doesn't actually work. To avoid shipping a
kernel that has it enabled but where it can't be used disable it
for now - we can re-enable it when it's fixed.
This partially reverts 44674d9c22 ("mac80211: advertise support
for full station state in AP mode").
Cc: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context driver operations can sleep, so add might_sleep()
and document this.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow distinguishing the non-station case from the case of a
station without rates, by using -1 for the non-station case.
This value cannot be reached with a station since that many
legacy rates don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.
The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)
Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drv_start() fails during hw_restart, all the running
interfaces are being closed/stopped, which results in
drv_stop() being called, although the driver was never
started successfully.
This might cause drivers to perform operations on uninitialized
memory (as they assume it was initialized on drv_start)
Consider the local->started flag, and call the driver's stop()
op only if drv_start() succeeded before.
Move drv_start() and drv_stop() to driver-ops.c, as they are no
longer simple wrappers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The recalc_smps work can run after the station disassociates.
At this stage we already released the channel, but the work
will be cancelled only when the interface stops.
In this scenario we can hit the warning in ieee80211_recalc_smps, so
just remove it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requesting hw restart during suspend might result
in the restart work being executed after mac80211
and the hw are suspended.
Solve the race by simply scheduling the restart
work on a freezable workqueue.
Note that there can be some cases of reconfiguration
on resume (besides the hardware restart):
* wowlan is not configured -
All the interfaces removed were removed on suspend,
and drv_stop() was called. At this point the driver
shouldn't expect for hw_restart anyway, so we can
simply cancel it (on resume).
* wowlan is configured, drv_resume() == 1
There is no definitive expected behavior in this case,
as each driver might have different expectations (e.g.
setting some flags on suspend/restart vs. not handling
spurious recovery).
For now, simply let the hw_restart work run again after
resume, and hope the driver will handle it well (or at
least initiate another hw restart).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Local request to deauthenticate wasn't handled while associating, thus
the association could continue even when the user space required to
disconnect.
Cc: stable@vger.kernel.org
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In TDLS channel-switch operations the chandef can sometimes be NULL.
Avoid an oops in the trace code for these cases and just print a
chandef full of zeros.
Cc: stable@vger.kernel.org
Fixes: a7a6bdd067 ("mac80211: introduce TDLS channel switch ops")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of one shot NOA the interval can be 0, catch that
instead of potentially (depending on the driver) crashing
like this:
divide error: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<ffffffffc08e891c>] ieee80211_extend_absent_time+0x6c/0xb0 [mac80211]
[<ffffffffc08e8a17>] ieee80211_update_p2p_noa+0xb7/0xe0 [mac80211]
[<ffffffffc069cc30>] ath9k_p2p_ps_timer+0x170/0x190 [ath9k]
[<ffffffffc070adf8>] ath_gen_timer_isr+0xc8/0xf0 [ath9k_hw]
[<ffffffffc0691156>] ath9k_tasklet+0x296/0x2f0 [ath9k]
[<ffffffff8107ad65>] tasklet_action+0xe5/0xf0
[...]
Cc: stable@vger.kernel.org [3.16+, due to d463af4a1c using it]
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=uZ5N
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another set of patches for the current cycle:
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.
Also rename the variables since the grouping now makes it
obvious where they belong.
This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This file only feeds a debugfs file that isn't very useful, so remove
it. If necessary, we can add other ways to get this information, for
example in the NL80211_CMD_PROBE_CLIENT response.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
That file contains just a single function, which itself is just a
single statement to call a different function. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single caller of this function, so it can
be moved to the same file and made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If multiple scan plans were set for scheduled scan, do not restart
scheduled scan on reconfig because it is possible that some scan
plans were already completed and there is no need to run them all
over again. Instead, notify userspace that scheduled scan stopped
so it can configure new scan plans for scheduled scan.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 30686bf7f5 ("mac80211: convert HW flags to unsigned long
bitmap") accidentally removed the newline delimiter from the hwflags
debugfs file. Fix this by adding back the newline between the HW flags.
Cc: stable@vger.kernel.org [4.2]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
[fix commit log]
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 5c48f12017.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
-----BEGIN PGP SIGNATURE-----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=BF9F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function returns always non-negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mac80211 code uses ktime_get_ts to measure the connected time.
As this uses monotonic time, it is y2038 safe on 32-bit systems,
but we still want to deprecate the use of 'timespec' because most
other users are broken.
This changes the code to use ktime_get_seconds() instead, which
avoids the timespec structure and is slightly more efficient.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of nesting two if statements, inline the second
check into the first if statement and to indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using software queueing, tx sequence number assignment happens at
ieee80211_tx_dequeue time, so the fast-xmit codepath must not do that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enables adding stations in unauthenticated mode, just after
receiving the first authentication frame; which in turn allows
sending a negative authentication reply if the station cannot be
added.
In addition init rate control for unassociated station only when
it becomes associated, prior to that low rates will be used.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain tests, for example replay detection, it can be useful
to be able to influence/set the PN used in outgoing packets. Make
it possible to change the TX PN in debugfs.
For now, this doesn't support TKIP since I haven't needed it, but
there's no reason it couldn't be added if necessary.
Note that this must be used very carefully: it could, for example,
be used to make "valid replays" where the PN reuse happens on a
different TID. This couldn't be done by an attacker since the TID
is protected as part of the AAD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining these functions have sizes and callsite counts
as follows:
drv_get_tsf: 634 bytes, 6 calls
drv_set_tsf: 626 bytes, 2 calls
drv_reset_tsf: 617 bytes, 2 calls
Total size reduction is about 4.2 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 755 bytes and there are
6 callsites.
Total size reduction is about 3.3 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 821 bytes and there are
2 callsites, reducing code size by about 800 bytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
[adjust code-style a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there are no supported rates in the rate mask with the required
flags, we warn, but it's not clear which part causes the warning.
Add the relevant data to the warning to understand why it happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace the average symbol by "avg" to avoid being warned about the
non-ASCII symbol all the time, line up the columns properly.
(I changed my mind - the warnings are getting annoying)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of "any" wowlan trigger, there is no reason to tear down
aggregations, as we want the device to continue working normally.
Similarly, there's no reason to tear down aggregations on resume,
as they should have been torn down on suspend if needed.
However, since the reconfiguration flow is shared with HW restart,
tear down aggregations on reconfiguration when we are not resuming.
To keep things working after non-wowlan suspend, keep clearing the
WLAN_STA_BLOCK_BA flag.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining these functions have sizes and callsite counts
as follows:
drv_add_interface: 638 bytes, 5 calls
drv_remove_interface: 611 bytes, 6 calls
drv_change_interface: 658 bytes, 1 call
Total size reduction is about 9 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 706 bytes and there are
2 callsites, reducing code size by about 700 bytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config_ALLYES_Os,
after deinlining the function size is 785 bytes and there are
7 callsites.
Total size reduction is about 3.5 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When debugging wireless powersave issues on the AP side it's quite helpful
to see our own beacons that are transmitted by the hardware/driver. However,
this is not that easy since beacons don't pass through the regular TX queues.
Preferably drivers would call ieee80211_tx_status also for tx'ed beacons
but that's not always possible. Hence, just send a copy of each beacon
generated by ieee80211_beacon_get_tim to monitor devices when they are
getting fetched by the driver.
Also add a HW flag IEEE80211_HW_BEACON_TX_STATUS that can be used by
drivers to indicate that they report TX status for beacons.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
(with a fix from Christian Lamparted rolled in)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes dropped packets in the tx path in case a non-PS station triggers
the tx filter.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current behavior of notifying CQM events is inconsistent:
Upon first configuration there is a cqm event with the current
status according to threshold configured, regardless of signal
stability.
When there is reconfiguration no event is sent unless there is
a significant change to the signal level according to the new
configuration.
Since the current reconfiguration behavior might cause missing
CQM events in case the current signal did not change but is on
the other side of the new threshold, fix that by resetting the
stored signal level upon reconfiguration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows ieee80211_tx_monitor to be used directly for sending 802.11 frames
to all monitor interfaces.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't seem problematic to change the weight for the average
beacon signal from 3 to 4, so use DECLARE_EWMA. This also makes
the code easier to maintain since bugs like the one fixed in the
previous patch can't happen as easily.
With a fix from Avraham Stern to invert the sign since EMWA uses
unsigned values only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
Fixes: 615f7b9bb1 ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These file aren't really useful:
- if per beacon data is required then you need to use
radiotap or similar anyway, debugfs won't help much
- average beacon signal is reported in station info in
nl80211 and can be looked up with iw
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the basics required for supporting very high throughput
with mesh: include VHT information elements in beacons, probe
responses, and peering action frames, and check for compatible VHT
configurations when peering.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clear the Channel Center Frequency Segment 2 in VHT operation
IEs to avoid sending non-zero values if the SKB wasn't zeroed
before adding the VHT operation IE.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[change commit message a bit - not necessarily just mesh related]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may be interested in receiving A-MSDU within A-MDPU.
Not all the devices may be able to do so, make it configurable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The direct probe step before authentication was done mostly for
two reasons:
1) the BSS data could be stale
2) the beacon might not have included all IEs
The concern (1) doesn't really seem to be relevant any more as
we time out BSS information after about 30 seconds, and in fact
the original patch only did the direct probe if the data was
older than the BSS timeout to begin with. This condition got
(likely inadvertedly) removed later though.
Analysing this in more detail shows that since we mostly use
data from the association response, the only real reason for
needing the probe response was that the code validates the WMM
parameters, and those are optional in beacons. As the previous
patches removed that behaviour, we can now remove the direct
probe step entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When checking if a TDLS chandef can be upgraded, IR-relaxation can be
taken into account to allow more channels.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Queued frames aren't processed during scan, which results in an inability
to complete the BA session establishment until the scan ends. Since we
can't tx frames until the BA agreement setup is complete, it might result
in a very large latency during scan.
Fix this by allowing to process queued skbs while scanning in HW. This
should be ok since the devices which support hw scan should be able
to handle tx/rx while scanning.
During SW scan, mac80211 drops any txed frames besides probes and NDPs,
so it is still needed to delay processing of the queued frames till the
SW scan is done.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The HT MCS mask has 9 bytes, the VHT one only has 8 streams.
Split the loops to handle this correctly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When beacon filtering is enabled the mac80211 software implementation
for RSSI CQM cannot work as beacons will not be available. Rather than
accepting such a configuration without proper effect, reject it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently if 80MHz channels are not allowed for use, the VHT IE is not
included in the probe request for an AP. This is not good enough if the
AP is configured with the wrong regulatory and supports VHT even where
prohibited or in TDLS scenarios.
Mark the ifmgd with the DISABLE_VHT flag for the misbehaving-AP case, and
unset VHT support from the peer-station entry for the TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT TDLS traffic should be protected in a non-HT BSS to avoid
collisions. Therefore, when TDLS peers join/leave, check if
protection is (now) needed and set the ht_operation_mode of
the virtual interface according to the HT capabilities of the
TDLS peer(s).
This works because a non-HT BSS connection never sets (or
otherwise uses) the ht_operation_mode; it just means that
drivers must be aware that this field applies to all HT
traffic for this virtual interface, not just the traffic
within the BSS. Document that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate_control_cap_mask() function takes a parameter mcs_mask, which
GCC will take to be u8 * even though it was declared with a fixed size.
This causes the following warning:
net/mac80211/rate.c: In function 'rate_control_cap_mask':
net/mac80211/rate.c:719:25: warning: 'sizeof' on array function parameter 'mcs_mask' will return size of 'u8 * {aka unsigned char *}' [-Wsizeof-array-argument]
for (i = 0; i < sizeof(mcs_mask); i++)
^
net/mac80211/rate.c:684:10: note: declared here
u8 mcs_mask[IEEE80211_HT_MCS_MASK_LEN],
^
This can be easily fixed by using the IEEE80211_HT_MCS_MASK_LEN directly
within the loop condition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using the out-of-line average calculation, use the new
DECLARE_EWMA() macro to declare a signal EWMA, and use that.
This actually *reduces* the code size slightly (on x86-64) while
also reducing the station info size by 80 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define rc_rateidx_vht_mcs_mask array and rate_idx_match_vht_mcs_mask()
method in order to apply mcs mask for vht rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define rate_control_apply_mask_ratetbl() in order to apply ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove ieee80211_tx_rate dependency in rate_idx_match_legacy_mask(),
rate_idx_match_mcs_mask() and rate_idx_match_mask() in order to use the
previous logic to define a ratemask in rate_control_set_rates() for
station rate table. Moreover move rate mask definition logic in
rate_control_cap_mask()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove unnecessary ieee80211_tx_info pointer from rate_control_apply_mask
signature. rate_control_apply_mask() will be used to define a ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Perform the BSS_CHANGED_BSSID action when joining an OCB network.
This is required to set the broadcast BSSID in some network drivers.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently OCB mode accepts frames with bssid==broadcast and type!=beacon.
Some non-data frames are sent matching this, for example probe responses.
This results in unnecessary creation of STA entries.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make mac80211 accept the multicast rate requested by the user the
rate control should be told that it is operating in BSS mode.
Without this, the default rate is selected in rate_control_send_low
(!pubsta and !txrc->bss)
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the last iteration of the loop, j may equal zero and thus
tp_list[j - 1] causes an invalid read.
Change the logic of the loop so that j - 1 is always >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The outside if statement checks that IEEE80211_TX_INTFL_MLME_CONN_TX is
set so this condition is always true. Checking twice upsets the static
checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlwifi driver was the only driver that used this, but as
it turns out it never needed it, so we can remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config,
after deinlining these functions have sizes and callsite counts
as follows:
rate_control_rate_init: 554 bytes, 8 calls
rate_control_rate_update: 1596 bytes, 5 calls
Total size reduction: about 11 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this .config: http://busybox.net/~vda/kernel_config,
after deinlining the function size is 3132 bytes and there are
7 callsites.
Total size reduction: about 20 kbytes.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of using peer link id for AID, generate a new
AID when creating mesh STAs in the kernel peering manager.
This enables smaller TIM elements and more closely follows
the standard, and it also enables mesh to work on drivers
that require a valid AID when the STA is inserted (ath10k
firmware has this requirement, for example).
In the case of userspace-managed stations, we use the AID
from NL80211_CMD_NEW_STATION.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 13.3.1, a mesh STA should assign an AID
upon receipt of a mesh peering open frame rather than using the link
id of the peer. Using the peer link id has two potential issues:
it may not be unique among the peers, and by its nature it is random,
so the TIM may not compress well.
In preparation for allocating it properly, use sta->sta.aid, but keep
the existing behavior of using the plid in the aid we send.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move mesh_plink_frame_tx() above the first caller to remove
the forward declaration.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 calls drv_resume() on wowlan resume,
but drops any incoming frame until local->suspended is
cleared later on.
This requires the low-level driver to support a new state,
in which it is expected to fully work (as it was resumed)
but not passing rx frames yet (as they will be dropped).
iwlwifi (and probably other drivers as well) has issues
supporting such mode.
Since in the wowlan case we already short-circuit
ieee80211_reconfig, there's nothing that prevents us from
clearing local->suspend before calling drv_resume(),
and letting the low-level driver work normally.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a TDLS station is not allowed to beacon on a channel, don't accept
a channel switch request to this channel.
Move channel building code up to avoid lockdep violations - reg_can_beacon
needs to take the wdev lock.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move TDLS channel-switch Rx handling into an RTNL locked work. This is
required to add proper regulatory checking to incoming channel-switch
requests.
Queue incoming requests in a dedicated skb queue and handle the request
in a device-specific work to avoid deadlocking on interface removal.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for declaring MU-MIMO beamformee capability for
relevant hardware.
When sending association request, the capability is included if both
hardware and the AP support it, and no other virtual interface
is using it.
This is in order to avoid multiple interfaces using MU-MIMO in parallel
which might lead to contradictions in the group-id mechanism.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an SKB will be segmented by the driver, count it for multiple
MSDUs that are being transmitted rather than just a single.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most of the fields in this struct use too wide types, change
that to shrink the struct from 64 to 48 bytes (on 64-bit.)
This results in a total saving of 64 bytes for each interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of Dynamic SMPS enable RTS/CTS for all rates.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
[change comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch does the following:
- Remove unnecessary flags field used by PERR element
- Use the per target flags defined in <linux/ieee80211.h>
- Process the target only subfield based on case E2 of
IEEE802.11-2012 13.10.9.3
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.
To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.
While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.
Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already set a station to be associated when peering completes, both
in user space and in the kernel. Thus we should always have an
associated sta before sending data frames to that station.
Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized. This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.
Cc: stable@vger.kernel.org
Reported-by: Alexis Green <agreen@cococorp.com>
Tested-by: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When processing a PREQ or PREP it's critical to use the incoming SN. If
that is improperly done routing loops and other types of badness can
happen. But the code was always processing path messages for deactivated
paths. This path fixes that so that if we have a valid SN then we use it
to verify that it is a message we can accept. For reference the relevant
section of the standard is 13.10.8.4 which doesn't address the deactivated
path case at all.
I also included a special case for when our peer reboots or restarts
networking. This is an important case because without it there can be a
very long delay before we accept path messages from that peer. It's also a
simple case and intimately associated with processing messages for
deactivated paths so I used one patch instead of two.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 2012 spec mentions that path SNs can be invalid when created (see
section 13.10.8.4 table 13-9) but AFAICT never talks about invalidating
SNs. Which makes sense: if we have figured out the path to a target at a
certain SN then we want to remember that fact. Failing to do so can lead
to routing loops because if we don't have a valid SN then we have no way
of knowing whether an incoming path message leads to or away from the
target.
However currently when discovery fails we zero out mpath->flags which
clears MESH_PATH_SN_VALID. This patch fixes that so that only the
discovery relevant flags are cleared.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the nexthop is unable to resolve its own nexthop it will send back a
PERR with a zero target_sn. According to section 13.10.11.4.3 step b in the
2012 standard that perr should be forwarded and the associated mpath->sn
should be incremented. Neither one of those was happening which is rather
bad because the originator was not told that packets are black holing.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define a station chandef, to be used for wider-bw TDLS peers. When both
peers support the feature, upgrade the channel bandwidth to the maximum
allowed by both peers and regulatory. Currently widths up to 80MHz are
supported in the 5GHz band.
When a TDLS peer connects/disconnects recalculate the channel type of the
current chanctx.
Make the chanctx width calculation consider wider-bw TDLS peers and
similarly fix the max_required_bw calculation for the chanctx min_def.
Since the sta->bandwidth is calculated only later on, take
bss_conf.chandef.width as the minimal width for station interface.
Set the upgraded channel width in the VHT-operation set during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow a device to specify support for the TDLS wider-bandwidth feature.
Indicate this support during TDLS setup in the ext-capab IE and set an
appropriate station flag when our TDLS peer supports it.
This feature gives TDLS peers the ability to use a wider channel than
the base width of the BSS. For instance VHT capable TDLS peers connected
on a 20MHz channel can extend the channel to 80MHz, if regulatory
considerations allow it.
Do not cap the bandwidth of such stations by the current BSS channel width
in mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If reconfiguration fails, local->in_reconfig is never
cleaned, resulting in rx frames being dropped next
time the device is started.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simply return NULL in this case, instead of crashing. This can
simplify callers that would otherwise have to check for this
explicitly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The beacon struct is already available in many contexts that
are also already in an RCU read-locked section. Avoid that by
using the existing beacon struct pointer directly.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
[rewrite subject/add commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code was always a bit awkward due to the 80-col restriction
and got worse in the previous patch. Refactor it a bit into its
own function to make it read nicer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are now a fairly large number of mesh fields that really
aren't needed in any other modes; move those into their own
structure and allocate them separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a long-standing TODO item to use this flag in the cooked
monitor RX, but clearly it was never needed and now this hasn't
been used by userspace for a long time, so no userspace changes
could require it now.
Remove the unused flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the station hash table lookup (or iteration) must
access two cachelines for each station - the one with the hash
table node, and the one with the MAC address.
Duplicate the MAC address next to the hash node to get rid of
this. Since the MAC address is static there's no consistency
problem introduced by this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are multiple RX queues, the PN checks in mac80211 cannot be
used since packets might be processed out of order on different CPUs.
Allow the driver to report that the PN has been checked, drivers that
will use multi-queue RX will have to set this flag.
For now, the flag is only valid when the frame has been decrypted, in
theory that restriction doesn't have to be there, but in practice the
hardware will have decrypted the frame already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This counter is inherently racy (since it can be incremented by RX
as well as by concurrent TX) and only available in debugfs. Instead
of fixing it to be per-CPU or similar, remove it for now. If needed
it should be added without races and with proper nl80211, perhaps
even addressing the threshold reporting TODO item that's been there
since the code was originally added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As there's no driver using this capability and reporting zero-length
A-MPDU subframes for radiotap monitoring, remove the capability to
free up two RX flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no RX queues in mac80211 (yet), the comment should refer
to the TID (including one slot for non-QoS) rather than 'RX queue'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is only used in the RX code, so moving it into
that file gives the compiler better optimisation possibilities
and also allows us to remove the check for short frames (which
in the RX path cannot happen, but as a generic utility needed
to be checked.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Short frames less than 16 octets are already blocked in the monitor
code by the should_drop_frame() function, and cannot get into the
regular RX path. Therefore, this check can never trigger and the
counter invariably stays zero. Remove the useless code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We typically use 'sta' for the station info struct, and if needed
'pubsta' for the public (driver-visible) portion thereof. Do this
in the ieee80211_sta_ps_transition() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RTNL is required to check for IR-relaxation conditions that allow
more channels to beacon. Export an RTNL locked version of reg_can_beacon
and use it where possible in AP/STA interface type flows, where
IR-relaxation may be applicable.
Fixes: 06f207fc54 ("cfg80211: change GO_CONCURRENT to IR_CONCURRENT for STA")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Although mesh_rx_plink_frame() already checks that frames have enough
bytes for the action code plus another two bytes for capability/reason
code, it doesn't take into account that confirm frames also have an
additional two-byte aid. As a result, a corrupt frame could cause a
subsequent subtraction to wrap around to ill effect. Add another
check for this case.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 8.5.16.3.2 AID comes directly after the
capability bytes in mesh peering confirm frames. The existing
code, however, was adding a 2 byte offset to this location,
resulting in garbage data going out over the air. Remove the
offset to fix it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the hardware is unregistered while interfaces are up, mac80211 will
unregister all interfaces, which in turns causes mac80211 to be called
again to remove them all from the driver and eventually shut down the
hardware.
During this shutdown, however, it's currently already unsafe to iterate
the list of interfaces atomically, as the list is manipulated in an
unsafe manner. This puts an undue burden on the driver - it must stop
all its activities before calling ieee80211_unregister_hw(), while in
the normal stop path it can do all cleanup in the stop method. If, for
example, it's using the iteration during RX for some reason, it would
have to stop RX before unregistering to avoid crashes.
Fix this problem by closing all interfaces before unregistering them.
This will cause the driver stop to have completed before we manipulate
the interface list, and after the driver is stopped *and* has called
ieee80211_unregister_hw() it really musn't be iterating any more as
the memory will be freed as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If for any reason we're in the middle of PS-polling or awake after
TX due to dynamic powersave while going to suspend, go back to save
power. This might cause a response frame to get lost, but since we
can't really wait for it while going to suspend that's still better
than not enabling powersave which would cause higher power usage
during (and possibly even after) suspend.
Note that this really only affects the very few drivers that use
the powersave implementation in mac80211.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
[rewrite misleading commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When acting as AP and a PS-Poll frame is received
associated station is marked as one in a Service
Period. This state is kept until Tx status for
released frame is reported. While a station is in
Service Period PS-Poll frames are ignored.
However if PS-Poll was received during A-MPDU
teardown it was possible to have the to-be
released frame re-queued back to pending queue.
In such case the frame was stripped of 2 important
flags:
(a) IEEE80211_TX_CTL_NO_PS_BUFFER
(b) IEEE80211_TX_STATUS_EOSP
Stripping of (a) led to the frame that was to be
released to be queued back to ps_tx_buf queue. If
station remained to use only PS-Poll frames the
re-queued frame (and new ones) was never actually
transmitted because mac80211 would ignore
subsequent PS-Poll frames due to station being in
Service Period. There was nothing left to clear
the Service Period bit (no xmit -> no tx status ->
no SP end), i.e. the AP would have the station
stuck in Service Period. Beacon TIM would
repeatedly prompt station to poll for frames but
it would get none.
Once (a) is not stripped (b) becomes important
because it's the main condition to clear the
Service Period bit of the station when Tx status
for the released frame is reported back.
This problem was observed with ath9k acting as P2P
GO in some testing scenarios but isn't limited to
it. AP operation with mac80211 based Tx A-MPDU
control combined with clients using PS-Poll frames
is subject to this race.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we don't do this, and we then fail to recreate the debugfs
directory during a mode change, then we will fail later trying
to add stations to this now bogus directory:
BUG: unable to handle kernel NULL pointer dereference at 0000006c
IP: [<c0a92202>] mutex_lock+0x12/0x30
Call Trace:
[<c0678ab4>] start_creating+0x44/0xc0
[<c0679203>] debugfs_create_dir+0x13/0xf0
[<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211]
Cc: stable@kernel.org
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Conflicts:
drivers/net/ethernet/mellanox/mlx4/main.c
net/packet/af_packet.c
Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a "param_lock" mutex to each module, and update params.c to use
the correct built-in or module mutex while locking kernel params.
Remove the kparam_block_sysfs_r/w() macros, replace them with direct
calls to kernel_param_[un]lock(module).
The kernel param code currently uses a single mutex to protect
modification of any and all kernel params. While this generally works,
there is one specific problem with it; a module callback function
cannot safely load another module, i.e. with request_module() or even
with indirect calls such as crypto_has_alg(). If the module to be
loaded has any of its params configured (e.g. with a /etc/modprobe.d/*
config file), then the attempt will result in a deadlock between the
first module param callback waiting for modprobe, and modprobe trying to
lock the single kernel param mutex to set the new module's param.
This fixes that by using per-module mutexes, so that each individual module
is protected against concurrent changes in its own kernel params, but is
not blocked by changes to other module params. All built-in modules
continue to use the built-in mutex, since they will always be loaded at
runtime and references (e.g. request_module(), crypto_has_alg()) to them
will never cause load-time param changing.
This also simplifies the interface used by modules to block sysfs access
to their params; while there are currently functions to block and unblock
sysfs param access which are split up by read and write and expect a single
kernel param to be passed, their actual operation is identical and applies
to all params, not just the one passed to them; they simply lock and unlock
the global param mutex. They are replaced with direct calls to
kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or
if the module is built-in, it locks the built-in mutex.
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
Unfortunately, Michal's change to fix AP_VLAN crypto tailroom
caused a locking issue that was reported by lockdep, but only
in a few cases - the issue was a classic ABBA deadlock caused
by taking the mtx after the key_mtx, where normally they're
taken the other way around.
As the key mutex protects the field in question (I'm adding a
few annotations to make that clear) only the iteration needs
to be protected, but we can also iterate the interface list
with just RCU protection while holding the key mutex.
Fixes: f9dca80b98 ("mac80211: fix AP_VLAN crypto tailroom calculation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes a bug in hwmp_preq_frame_process where the wrong metric
can be used when forwarding a PREQ. This happens because the code uses
the same metric variable to record the value of the metric to the source
of the PREQ and the value of the metric to the target of the PREQ.
This comes into play when both reply and forward are set which happens
when IEEE80211_PREQ_PROACTIVE_PREP_FLAG is set and when MP_F_DO | MP_F_RF
is set. The original code had a special case to handle the first case
but not the second.
The patch uses distinct variables for the two metrics which makes the
code flow much clearer and removes the need to restore the original
value of metric when forwarding.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In mesh mode there is a race between establishing links and processing
rates and capabilities in beacons. This is very noticeable with slow
beacons (e.g. beacon intervals of 1s) and manifested for us as stations
using minstrel when minstrel_ht should be used. Fixed by changing
mesh_sta_info_init so that it always checks rates and such if it has not
already done so.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa counter has moved from sdata to beacon/presp but
it is not updated accordingly for mesh and ibss. Fix this.
Fixes: af296bdb8d ("mac80211: move csa counters from sdata to beacon/presp")
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The last hop metric should refer to link cost (this is how
hwmp_route_info_get uses it for example). But in mesh_rx_path_sel_frame
we are not dealing with link cost but with the total cost to the origin
of a PREQ or PREP.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The scan result ignores those invalid values and the
station last signal should not be updated as well.
In case the scan determines the signal to be invalid turn on
the flag so the station last signal will not be updated with
the value and thus user space probing for NL80211_STA_INFO_SIGNAL
and NL80211_STA_INFO_SIGNAL_AVG will not get this invalid RSSI
value.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few rare cases when upon
authentication failure channel wasn't released.
This could cause stale pointers to remain in
chanctx assigned_vifs after interface removal and
trigger general protection fault later.
This could be triggered, e.g. on ath10k with the
following steps:
1. start an AP
2. create 2 extra vifs on ath10k host
3. connect vif1 to the AP
4. connect vif2 to the AP
(auth fails because ath10k firmware isn't able
to maintain 2 peers with colliding AP mac
addresses across vifs and consequently
refuses sta_info_insert() in
ieee80211_prep_connection())
5. remove the 2 extra vifs
6. goto step 2; at step 3 kernel was crashing:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: ath10k_pci ath10k_core ath
...
Call Trace:
[<ffffffff81a2dabb>] ieee80211_check_combinations+0x22b/0x290
[<ffffffff819fb825>] ? ieee80211_check_concurrent_iface+0x125/0x220
[<ffffffff8180f664>] ? netpoll_poll_disable+0x84/0x100
[<ffffffff819fb833>] ieee80211_check_concurrent_iface+0x133/0x220
[<ffffffff81a0029e>] ieee80211_open+0x3e/0x80
[<ffffffff817f2d26>] __dev_open+0xb6/0x130
[<ffffffff817f3051>] __dev_change_flags+0xa1/0x170
...
RIP [<ffffffff81a23140>] ieee80211_chanctx_radar_detect+0xa0/0x170
(gdb) l * ieee80211_chanctx_radar_detect+0xa0
0xffffffff81a23140 is in ieee80211_chanctx_radar_detect (/devel/src/linux/net/mac80211/util.c:3182).
3177 */
3178 WARN_ON(ctx->replace_state == IEEE80211_CHANCTX_REPLACES_OTHER &&
3179 !list_empty(&ctx->assigned_vifs));
3180
3181 list_for_each_entry(sdata, &ctx->assigned_vifs, assigned_chanctx_list)
3182 if (sdata->radar_required)
3183 radar_detect |= BIT(sdata->vif.bss_conf.chandef.width);
3184
3185 return radar_detect;
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The conversion to the fast-xmit path lost proper aggregation session
timeout handling - the last_tx wasn't set on that path and the timer
would therefore incorrectly tear down the session periodically (with
those drivers/rate control algorithms that have a timeout.)
In case of iwlwifi, this was every 5 seconds and caused significant
throughput degradation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the pointers are really only accessible to root and used
pretty much only by wpa_supplicant, this is still not great; even
for debugging it'd be easier to have something that's easier to
read and guaranteed to never get reused.
With the recent change to make mac80211 create an ack_skb for the
mgmt-tx path this becomes possible, only the client probe method
needs to also allocate an ack_skb, and we can store the cookie in
that skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we return the TX status for an nl80211 mgmt TX SKB, we
should also return the original frame with the status to
allow userspace to match up the submission (it could also
use the cookie but both ways are permissible.)
As TX SKBs could be encrypted, at least in the case of ANQP
while associated with the AP, copy the original SKB, store
it with an ACK frame ID and restructure the status path to
use that to return status with the original SKB. Otherwise,
userspace (in particular wpa_supplicant) will get confused.
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers supporting TSO or similar features, but that still have
PN assignment in software, there's a need to have some memory to
store the current PN value. As mac80211 already stores this and it's
somewhat complicated to add a per-driver area to the key struct (due
to the dynamic sizing thereof) it makes sense to just move the TX PN
to the keyconf, i.e. the public part of the key struct.
As TKIP is more complicated and we won't able to offload it in this
way right now (fast-xmit is skipped for TKIP unless the HW does it
all, and our hardware needs MMIC calculation in software) I've not
moved that for now - it's possible but requires exposing a lot of
the internal TKIP state.
As an bonus side effect, we can remove a lot of code by assuming the
keyseq struct has a certain layout - with BUILD_BUG_ON to verify it.
This might also improve performance, since now TX and RX no longer
share a cacheline.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to associate, the AP could send a deauth frame instead.
Currently mac80211 drops that frame and doesn't report it to the
supplicant, which, in some versions and/or in certain circumstances
will simply keep trying to associate over and over again instead of
trying authentication again.
Fix this by reacting to deauth frames while associating, reporting
them to the supplicant and dropping the association attempt (which
is bound to fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJVaEyAAAoJEDBSmw7B7bqrPiIQAKOrX4g2UNtyoTWJzA7YRu+g
GEUu/CE4LQKCodCpBiEhFlhQo2WzXsHoLj5+Nr56aFAZx19VZjXWVC5JS785wYn5
r8hpOVWUUA3MVnXeL/+yz4chm0wTYN9pSpElZ4FHlUI0OkCMh2rPCTvdrbSKoGzV
MN8NEO0jVE89AgOMF8gHk5YKpJ6B4QibZuUuZpgkqdwIi5udaCcrPFFrUg/NfRpA
nTauP6blFUPOUV0sxbhS78uC3rqGQuYsnvab/QeGc9PDKk5ukrXzFdgRCVZq8224
Ge0JcPzwzWldk892oEJoc2OfGkg5HOil9HtC+S2ehBGuK0yEXOBIkO1ZgudTH1kC
0rLOPWVKRzTWE+sq+gWK/OjfaA7Dl6HFYYHRQ2dhm1XkqtAw8SwGQMDSIPJYWr4O
jp4gYpwKVjnMmsEAg7FdKWyIiTgLyI07VnIciORXDyefddYMuofXI2pJkfzUeFeH
HjCVYm2NYXDty6uneP4RC1nUbNc53FKJ5O9fW3BPMyVXD4pTjam50p9H6N7OcDN3
k3dEevWiVgvBjZPVc3HI8RaCzS/Ww1ym+MYgV97QkMfgiuE2VkiFwK+zhWn9axbc
eutkzFEdDcIACCZ74hIWqMJjsMnZm9E11Uq7tifAE0bi1Wpku1xPAnxMPnI+0eiF
Dgo2bmlQ/d1dHr3N3FC0
=KmwY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
As we get closer to the merge window, here are a few
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a possible race between
ieee80211_reconfig() and
ieee80211_delayed_tailroom_dec(). This could
result in inability to transmit data if driver
crashed during roaming or rekeying and subsequent
skbs with insufficient tailroom appeared.
This race was probably never seen in the wild
because a device driver would have to crash AND
recover within 0.5s which is very unlikely.
I was able to prove this race exists after
changing the delay to 10s locally and crashing
ath10k via debugfs immediately after GTK
rekeying. In case of ath10k the counter went below
0. This was harmless but other drivers which
actually require tailroom (e.g. for WEP ICV or
MMIC) could end up with the counter at 0 instead
of >0 and introduce insufficient skb tailroom
failures because mac80211 would not resize skbs
appropriately anymore.
Fixes: 8d1f7ecd2a ("mac80211: defer tailroom counter manipulation when roaming")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch makes use of the new AEAD interface which uses a single
SG list instead of separate lists for the AD and plain text.
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a station does a channel switch, it's not well defined what its TDLS
peers would do. Avoid a situation when the local side marks a potentially
disconnected peer as a TDLS peer.
Keeping peers connected through CSA is doubly problematic with the upcoming
TDLS WIDER-BW feature which allows peers to widen the BSS channel. The
new channel transitioned-to might not be compatible and would require
a re-negotiation anyway.
Make sure to disallow new TDLS link during CSA.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some splats I was seeing:
(a) WARNING: CPU: 1 PID: 0 at /devel/src/linux/net/mac80211/wep.c:102 ieee80211_wep_add_iv
(b) WARNING: CPU: 1 PID: 0 at /devel/src/linux/net/mac80211/wpa.c:73 ieee80211_tx_h_michael_mic_add
(c) WARNING: CPU: 3 PID: 0 at /devel/src/linux/net/mac80211/wpa.c:433 ieee80211_crypto_ccmp_encrypt
I've seen (a) and (b) with ath9k hw crypto and (c)
with ath9k sw crypto. All of them were related to
insufficient skb tailroom and I was able to
trigger these with ping6 program.
AP_VLANs may inherit crypto keys from parent AP.
This wasn't considered and yielded problems in
some setups resulting in inability to transmit
data because mac80211 wouldn't resize skbs when
necessary and subsequently drop some packets due
to insufficient tailroom.
For efficiency purposes don't inspect both AP_VLAN
and AP sdata looking for tailroom counter. Instead
update AP_VLAN tailroom counters whenever their
master AP tailroom counter changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to remain-on-channel scheduling delays, when we split an ROC
while coalescing, we'll usually get a picture like this:
existing ROC: |------------------|
current time: ^
new ROC: |------| |-------|
If the expected response frames are then transmitted by the peer
in the hole between the two fragments of the new ROC, we miss
them and the process (e.g. ANQP query) fails.
mac80211 expects that the window to miss something is small:
existing ROC: |------------------|
new ROC: |------||-------|
but that's normally not the case.
To avoid this problem, coalesce only if the new ROC's duration
is <= the remaining time on the existing one:
existing ROC: |------------------|
new ROC: |-----|
and never split a new one but schedule it afterwards instead:
existing ROC: |------------------|
new ROC: |-------------|
type=bugfix
bug=not-tracked
fixes=unknown
Reported-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: EliadX Peller <eliad@wizery.com>
Reviewed-by: Matti Gottlieb <matti.gottlieb@intel.com>
Tested-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers with fast-xmit (e.g. ath10k) running in
AP_VLAN setups would fail to communicate with
connected 4addr stations.
The reason was when new station associates it
first goes into master AP interface. It is not
until later that a dedicated AP_VLAN is created
for it and the station itself is moved there.
After that Tx directed at the station should use
4addr header. However fast-xmit wasn't
recalculated and 3addr header remained to be used.
This in turn caused the connected 4addr stations
to drop packets coming from the AP until some
other event would cause fast-xmit to recalculate
for that station (which could never come).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My recent change here introduced a possible memory leak if the
driver registers an invalid cipher schemes. This won't really
happen in practice, but fix the leak nonetheless.
Fixes: e3a55b5399 ("mac80211: validate cipher scheme PN length better")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* LED throughput trigger was crashing
* fast-xmit wasn't treating QoS changes in IBSS correctly
* TDLS could use the wrong channel definition
* using a reserved channel context could use the wrong channel width
-----BEGIN PGP SIGNATURE-----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=iUFe
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This just has a few fixes:
* LED throughput trigger was crashing
* fast-xmit wasn't treating QoS changes in IBSS correctly
* TDLS could use the wrong channel definition
* using a reserved channel context could use the wrong channel width
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter how the driver manages its NAPI context, there's no way
sending frames to it from a timer can be correct, since it would
corrupt the internal GRO lists.
To avoid that, always use the non-NAPI path when releasing frames
from the timer.
Cc: stable@vger.kernel.org
Reported-by: Jean Trivelly <jean.trivelly@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
As I was testing with hwsim, I missed that my previous commit to
make LED work depend on activation broke the code because I missed
removing the old trigger struct and some code was still using it,
now erroneously, causing crashes.
Fix this by always using the correct struct.
Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The chandef of the current channel context might be wider (though
compatible). The TDLS link cares only about the channel of the BSS.
In addition make sure to specify the VHT operation IE when VHT is supported
on a non-2.4GHz band, as required by IEEE802.11ac-2013. This is not the
same as HT-operation, to be specified only if the BSS doesn't support HT.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove checking tailroom when adding IV as it uses only
headroom, and move the check to the ICV generation that
actually needs the tailroom.
In other case I hit such warning and datapath don't work,
when testing:
- IBSS + WEP
- ath9k with hw crypt enabled
- IPv6 data (ping6)
WARNING: CPU: 3 PID: 13301 at net/mac80211/wep.c:102 ieee80211_wep_add_iv+0x129/0x190 [mac80211]()
[...]
Call Trace:
[<ffffffff817bf491>] dump_stack+0x45/0x57
[<ffffffff8107746a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff8107755a>] warn_slowpath_null+0x1a/0x20
[<ffffffffc09ae109>] ieee80211_wep_add_iv+0x129/0x190 [mac80211]
[<ffffffffc09ae7ab>] ieee80211_crypto_wep_encrypt+0x6b/0xd0 [mac80211]
[<ffffffffc09d3fb1>] invoke_tx_handlers+0xc51/0xf30 [mac80211]
[...]
Cc: stable@vger.kernel.org
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an IBSS station gets QoS enabled after having been added,
check fast-xmit to make sure the QoS header gets added to the
cache properly and frames can go out with QoS and higher rates.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a vif starts using a reserved channel context (during CSA, for example)
the required chandef was recalculated, however it was never applied.
This could result in using chanctx with narrower width than actually
required. Fix this by calling ieee80211_change_chanctx with the recalculated
chandef. This both changes the chanctx's width and recalcs min_def.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was missed in the previous patch, add some documentation
for rate_ctrl_lock to avoid docbook warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a cipher scheme can advertise an arbitrarily long
sequence counter, but mac80211 only supports up to 16 bytes
and the initial value from userspace will be truncated.
Fix two things:
* don't allow the driver to register anything longer than
the 16 bytes that mac80211 reserves space for
* require userspace to specify a starting value with the
correct length (or none at all)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No current (and planned, as far as I know) wifi devices support
encapsulation checksum offload, so remove the useless test here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When LED triggers are compiled in, but not used, mac80211 will still
call them to update the status. This isn't really a problem for the
assoc and radio ones, but the TX/RX (and to a certain extend TPT)
ones can be called very frequently (for every packet.)
In order to avoid that when they're not used, track their activation
and call the corresponding trigger (and in the TPT case, account for
throughput) only when the trigger is actually used by an LED.
Additionally, make those trigger functions inlines since theyre only
used once in the remaining code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is just a code cleanup, make the LED trigger names const
as they're not expected to be modified by drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove items that can be retrieved through nl80211. This also
removes two items (tx_packets and tx_bytes) where only the VO
counter was exposed since they are split up per AC but in the
debugfs file only the first AC was shown.
Also remove the useless "dev" file - the stations have long
been in a sub-directory of the netdev so there's no need for
that any more.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This counter is unsafe with concurrent TX and is only exposed
through debugfs and ethtool. Instead of trying to fix it just
remove it for now, if it's really needed then it should be
exposed through nl80211 and in a way that drivers that do the
fragmentation in the device could support it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since these counters can only be read through debugfs, there's
very little point in maintaining them all the time. However,
even just making them depend on debugfs is pointless - they're
not normally used. Additionally a number of them aren't even
concurrency safe.
Move them under MAC80211_DEBUG_COUNTERS so they're normally
not even compiled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debugfs statistics macros are pointlessly verbose, so change
that macro to just have a single argument. While at it, remove
the unused counters and rename rx_expand_skb_head2 to the better
rx_expand_skb_head_defrag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently while associated to an AP and sending a (public) action
frame to a different AP on the same channel, the action frame will
be sent like a regular tx frame without going off channel.
When power save is enabled this can cause problems, since the device
can go into power save and miss the response to the action frame
that is sent by the other AP.
Force off-channel transmission to avoid this issue in case
- HW offchannel is used,
- the user didn't forbid transmitting frames off channel
- the frame is not sent to the AP that we are associated with
(if it is we assume the response would be bufferable)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When frames time out in the reordering buffer, it is a
good indication that something went wrong and the driver
may want to know about that to take action or trigger
debug flows.
It is pointless to notify the driver about each frame that
is released. Notify each time the timer fires.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we receive a BAR, this typically means that our peer
doesn't hear our Block-Acks or that we can't hear its
frames. Either way, it is a good indication that the link
is in a bad condition. This is why it can serve as a probe
to the driver.
Use the event_callback callback for this.
Since more events with the same data will be added in the
feature, the structure that describes the data attached to
the event is called in a generic name: ieee80211_ba_event.
This also means that from now on, the event_callback can't
sleep.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT and VHT override configurations were ignored during association and
applied only when first beacon recived, or not applied at all.
Fix the code to apply HT/VHT overrides during association. This is a bit
tricky since the channel was already configured during authentication
and we don't want to reconfigure it unless there's really a change.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't all that relevant for RX right now, but TX can be concurrent
due to multi-queue and the accounting is therefore broken.
Use the standard per-CPU statistics to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't necessary any more as the stack will automatically
update the TXQ's trans_start after calling ndo_start_xmit().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The OCB input path already checked that the BSSID is the broadcast
address, so the later check can never fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function really shouldn't be called prepare_for_handlers(),
all it does is check if the frame should be dropped. Rename it
to ieee80211_accept_frame() and clean it up a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With promisc support gone, only AP and P2P-Device type interfaces
still clear IEEE80211_RX_RA_MATCH. In both cases this isn't really
necessary though, so we can remove that flag and the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hashtable behaviour change was merged into the tree
at about the same time as the mac80211 use of rhashtable,
but of course these don't really conflict in the normal
sense. Enable hash table shrinking now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow debug builds to configure the station hash table maximum
size in order to run with hash collisions in limited scenarios
such as hwsim testing. The default remains 0 which effectively
means no limit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My conversion of the mac80211 station hash table to rhashtable
completely broke the lookup in sta_info_get() as it no longer
took into account the virtual interface. Fix that.
Fixes: 7bedd0cfad ("mac80211: use rhashtable for station table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All users of AEAD should include crypto/aead.h instead of
include/linux/crypto.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Implement the necessary software segmentation on the normal
TX path so that fast-xmit can use segmentation offload if
the hardware (or driver) supports it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If drivers want to support S/G (really just gather DMA on TX) then
we can now easily support this on the fast-xmit path since it just
needs to write to the ethernet header (and already has a check for
that being possible.)
However, disallow this on the regular TX path (which has to handle
fragmentation, software crypto, etc.) by calling skb_linearize().
Also allow the related HIGHDMA since that's not interesting to the
code in mac80211 at all anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
