dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since commit 9840354ff4 ("usb: dwc3: Add dual-role support") dwc3
node requires extcon property to be initialized as OTG mode and it
supports dual-role mode operation.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 has two usb 3.0 controllers: usbhost and usbdrd. usbhost
is host-only controller whereas usbdrd supports both peripheral and
host mode. "drd" means dual-role device, so usbhost cannot be labeled
with the name containing "drd". However, the label usbdrd_dwc3_0 was
used for usbhost's dwc3 node. It seems it obviously fault because TM2
and TM2E doesn't use usbhost but dr_mode property is assigned to it.
This patch assigns the proper label for two dwc3 nodes.
Signed-off-by: Dongwoo Lee <dwoo08.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The OF graph is not needed because the panel is a child of dsi. Remove
the ports node in DSI node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The decon uses HW-TRIGGER, so TE interrupt is not necessary.
Therefore, remove the te-gpios property in the TM2 dts.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the panel device tree node for s6e3hf2 display
controller to TM2e dts.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the burst and esc clock frequency properties to the parent (DSI node).
Currently the clock is parsed from the port node, while it should be
taken from the dsi node.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
TM2 and TM2E devices are provided with a ST-Microelectronics
Finger Tip S device with small differences:
- screen size
- TM2E uses the stmfts also as a touchkey for "back" and "menu"
In this commit the initial value of the interrupt line is set to
EXYNOS_PIN_PULL_UP as the interrupt is triggered when the line
goes down.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the device tree node for the ir-spi driver which enables the
IR LED for remote controlling.
This patch sets first the GPR3[3] gpio line as a regulator-fixed
for enabling an external regulator which powers the IR LED.
Removes also the default assignment of GPG3[7] related to the
MOSI line of the SPI3 bus.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIUAwUAWK9htWCrR//JCVInAQL5sg/40ehZk89xuReYHaOoL0jkEGxt7ogae2Q0
5SurlVNEjkr1A6KKcTKwy6c8E4GReq0ioVUxyYHlNo2MedtLQWssSvObfjt390E+
OYXhuHHyHFgut9jF6nq1IZbSqkhaDcoRFdK0EPzjdxTMMk59xqzG2t9Kbq0MFz0I
Fg0+xB44VAOwuM+45MjNzdpTzolkH3gxlK4TV/opbr2/9uEDCjFOLr1zqZuWqIDh
uyXXqHYUZ54kz2GvhfYPgcm+f+PjuV2fw/Jh5u3+jNvwMQvA70Erv52im1o1a3GV
UTjmBgccTKByrPk7gXP3lgRkHQGwPLNH0L+28AZ/BNuZbWqDrDe7uVfpq9nWb5Xl
IR0uleNBOuiOdqR6Ya4xosGSm6AOgQhCbE52trHdUhb03eqRbqHcLHEVmZXXea/i
EejGOciIvbV8ent9jjREw/kvGZ+Ws6v5notG4uPDwn+YZSJAyqvGh5Tul8WzZIxk
Wr1WZgbuwkI0KYiFzSINfgDX0Om2l6YoVZLnkjst5Exto+TGRSINJpVCXsuGIU7O
34qZD25yA8WlJTooBL0cvrW0NT2RewBqLogwhbwDnRW241SW5AnuzPsFPWldLzon
L5sFgsF60gWiIlbB2/BKdpF2jB/+brXNR6epnQYADigweg/4+pS8HPZRFj7g8wyE
s22+OYJ6Cg==
=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Adding fixed voltage regulators for Vbus and Vbus-boost required
by USB 3.0 DRD controller on Exynos7-espresso board.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add USB 3.0 DRD controller device node, with its clock
and phy information to enable the same on Exynos7.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.
TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 LPASS module requires some clocks for proper operation with
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LDO7 regulator beside DSI and HDMI provides power for core blocks in Exynos
5433 SoC. Disabling it causes serious current leak - about 200mA.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Ultra HD modes requires clock ticking at increased rate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As per Exynos7 datasheet FSYS1 pinctrl block does not support drive
strength value of 0x3. This patch fixes this and update the correct
drive strength for sd0_xxx pin definitions.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Common definition for I2S, PMC, SPDIF buses should not define any pull
control for the individual pins. Correct this by changing samsung,pin-pud
property to EXYNOS_PIN_PULL_NONE like it is defined for other Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "samsung,exynos5433-mipi-video-phy" and "samsung,exynos5250-dwusb3"
DT bindings don't specify a reg property for these nodes, so having a
unit name leads to the following DTC warnings:
Node /soc/video-phy@105c0710 has a unit name, but no reg property
Node /soc/usb@15400000 has a unit name, but no reg property
Node /soc/usb@15a00000 has a unit name, but no reg property
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
HDMI converts RGB/I80 signal from DECON_TV to HDMI/TMDS video stream.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DECON_TV is 2nd display controller on Exynos5433, used in HDMI path
or 2nd DSI path.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Address should not contain 0x prefix.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tree-wide replacement was done by commit 2ef7d5f342 ("ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), then the 2nd
round by commit 15b7cc78f0 ("arm64: dts: drop "arm,amba-bus" in
favor of "simple-bus" part 2").
Here, some new users have appeared for Linux v4.10-rc1. Eliminate
them now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently TM2E dts includes TM2 but there are some differences
between the two boards and TM2 has some properties that TM2E
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch fixes wrong values assigned to ldo23 and ldo25 on both TM2 and TM2E.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Change the PIN() macro definition so that it can use the macros
from pinctrl/samsung.h header file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use the macros defined in include/dt-bindings/pinctrl/samsung.h
instead of hardcoded values.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the bus Device-tree nodes for INT (Internal) block
and enables the bus frequency scaling.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the AMBA AXI bus nodes using VDD_INT for Exynos5433 SoC.
Following list specify the detailed correlation between sub-block and clock:
- CLK_ACLK_G2D_{400|266} : Bus clock for G2D (2D graphic engine)
- CLK_ACLK_MSCL_400 : Bus clock for MSCL (Memory to memory Scaler)
- CLK_ACLK_GSCL_333 : Bus clock for GSCL (General Scaler)
- CLK_SCLK_JPEG_MSCL : Bus clock for JPEG
- CLK_ACLK_MFC_400 : Bus clock for MFC (Multi Format Codec)
- CLK_ACLK_HEVC_400 : Bus clock for HEVC (High Efficient Video Codec)
- CLK_ACLK_BUS0_400 : NoC's (Network On Chip) bus clock for PERIC/PERIS/FSYS/MSCL
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds PPMU (Platform Performance Monitoring Unit) Device-tree node
to measure the utilization of each IP in Exynos SoC.
- PPMU_D{0|1}_CPU are used to measure the utilization of MIF (Memory Interface)
block with VDD_MIF power source.
- PPMU_D{0|1}_GENERAL are used to measure the utilization of INT(Internal)
block with VDD_INT power source.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
1. Add Performance Monitor Unit to Exynos7.
2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
3. Cleanups and fixes for recently added TM2 and TM2E boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/AE/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DeviceTree arm64 second update for v4.10" from Krzysztof Kozłowski:
1. Add Performance Monitor Unit to Exynos7.
2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
3. Cleanups and fixes for recently added TM2 and TM2E boards.
* tag 'samsung-dt64-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: dts: exynos: TM2 - add support for MFC video codec device
arm64: dts: exynos: TM2 - add support for JPEG codec device
arm64: dts: exynos: TM2 - add support for GScaler devices
arm64: dts: exynos: TM2 - remove unused UART3 and set clocks directly on CMU
arm64: dts: exynos: Assign parent clock of the clkout clock for TM2 board
arm64: dts: exynos: Move FSYS CMU configuration from Exynos5433 dtsi to TM2 dts
arm64: dts: exynos: Add missing parent clocks to audio block in Exynos5433 SoC
arm64: dts: exynos: Fix FSYS CMU parent clocks in Exynos5433 SoC
arm64: dts: exynos: Fix IRQ type flags for Exynos5433 SoC
arm64: dts: Add ARM PMU node for exynos7
TM2 can support the HS400 mode, but eMMC is working in the lowest mode.
This patch adds the properties for HS400 and other modes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the mshc_2 node for supporting T-Flash.
Also add the "mshc*" aliases. dwmmc driver should be assigned to
"ctrl_id" after parsing to "mshc". If there are no aliases for mshc,
then it might be set to the wrong capabilities.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=j/xt
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Topic branch with DT arm64 changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for interrupt properties in exynos7
arm64: dts: exynos: Fix invalid GIC interrupt flags in exynos7
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device nodes for MFC video codec device to Exynos5433 SoC
dtsi and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for JPEG codec device to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for GScaler devices to Exynos5433 SoC dtsi
and proper initial clock configuration to TM2 dts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
UART3 device is not really needed for enabling audio block on TM2.
Enabling it made it working by enabling some common parent clocks,
what is now handled by improved exynos5433 clocks driver. Thus the UART3
device node can be safely disabled. The assigned-clocks entries are
however still needed, so move them under the respective CMU node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Without this patch the clkout clock is orphaned and sound doesn't
work properly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move initial FSYS CMU (related to USB 3.0 devices) clocks configuration
from generic exynos5433.dtsi file to exynos5433-tm2.dts, as this is
a board specific item.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Audio PLL and oscillator clocks are proper parent clocks for AUD CMU.
They are not visible as such on first glance on Exynos5433 SoC docs,
but they are needed for this CMU to operate properly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch corrects FSYS CMU parent clocks specified in clock controller
node to let improved Exynos5433 clocks driver to control proper clocks
on FSYS<->TOP CMU boundary.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts. The
GIC requires shared interrupts to be edge rising or level high. Platform
declares support for both. Set all interrupts type to level high, as this
works fine - tested on Exynos5433-based TM2 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
