Asics that use an AGP to PCIE bridge don't have the AGP_STATUS
register so just use whatever mode the host side setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the connector is eDP, it can only be DP, not TMDS.
Always set the detected sink type. If the sink is
detected as non-DP, but there is no EDID, you can still
manually force the port on. If the sink type is DP
and there's no DPCD, there's no way to force the monitor
on since you need both ends to train the link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pins for ddc and aux are shared so you need to switch the
mode when doing ddc. The ProcessAuxChannel table already sets
the pin mode to DP. This should fix unreliable ddc issues
on DP ports using non-DP monitors.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows the tables to be run in some additional cases
where the connector info isn't necessary.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- INIT action takes the actual connector type id, not the enum id
- some evergreen cards have the ENABLE_OUTPUT/DISABLE_OUTPUT actions
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On most newer asics, digital encoders have two links each
and they can be used independantly. As such, treat them as
separate encoders otherwise the individual links will not
get programmed properly at modeset time.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add options necessary bits for:
- SS on DP
- SS on LVDS
- set clocks right for DP
- deep color on hdmi (needs additional encoder and edid work as well)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always zero-init a structure on the stack which is returned by a
function. Otherwise you may leak random stack data from previous
function calls.
This fixes the following warning I was seeing:
CC [M] drivers/gpu/drm/radeon/radeon_atombios.o
drivers/gpu/drm/radeon/radeon_atombios.c: In function "radeon_atom_get_hpd_info_from_gpio":
drivers/gpu/drm/radeon/radeon_atombios.c:261: warning: "hpd.plugged_state" is used uninitialized in this function
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GTT/VRAM overlapping test had a typo which leaded to not
detecting case when vram_end > gtt_end. This patch fix the
logic and should fix#16574
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the current screwed but its ABI, ioctls for the drm, Linus pointed out that we could allow userspace to specify the allocation size, but we pass it to the driver which then uses it blindly to store a struct. Now if userspace specifies the allocation size as smaller than the driver needs, the driver can possibly overwrite memory.
This patch restructures the driver ioctls so we store the structure size we are expecting, and make sure we allocate at least that size. The copy from/to userspace are still restricted to the size the user specifies, this allows ioctl structs to grow on both sides of the equation.
Up until now we didn't really use the DRM_IOCTL defines in the kernel, so this cleans them up and adds them for nouveau.
v2:
fix nouveau pushbuf arg (thanks to Ben for pointing it out)
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (55 commits)
io-mapping: move asm include inside the config option
vgaarb: drop vga.h include
drm/radeon: Add probing of clocks from device-tree
drm/radeon: drop old and broken mesa warning
drm/radeon: Fix pci_map_page() error checking
drm: Remove count_lock for calling lastclose() after 58474713 (v2)
drm/radeon/kms: allow FG_ALPHA_VALUE on r5xx
drm/radeon/kms: another r6xx/r7xx CS checker fix
DRM: Replace kmalloc/memset combos with kzalloc
drm: expand gamma_set
drm/edid: Split mode lists out to their own header for readability
drm/edid: Rewrite mode parse to use the generic detailed block walk
drm/edid: Add detailed block walk for VTB extensions
drm/edid: Add detailed block walk for CEA extensions
drm: Remove unused fields from drm_display_info
drm: Use ENOENT consistently for the error return for an unmatched handle.
drm/radeon/kms: mark 3D power states as performance
drm: Only set DPMS once on the CRTC not after every encoder.
drm/radeon/kms: add additional quirk for Acer rv620 laptop
drm: Propagate error code from fb_create()
...
Fix up trivial conflicts in drivers/gpu/drm/drm_edid.c
When we find no ROM we understand and a device-tree is present, see
if we can retreive clock info from there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This never really got fixed in mesa, and the kernel deals with the problem
just fine, so don't got reporting things that confuse people.
Signed-off-by: Dave Airlie <airlied@redhat.com>
0 is a valid DMA address from pci_map_page(), use pci_dma_mapping_error()
instead to check for errors
[airlied: fix warning + two other places with errors.]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a CS checker fix. I need this for FP16 alpha-test.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
add default case for buffer formats
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Andre Maasikas <amaasikas@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jesse's initial patch commit said:
"At panic time (i.e. when oops_in_progress is set) we should try a bit
harder to update the screen and make sure output gets to the VT, since
some drivers are capable of flipping back to it.
So make sure we try to unblank and update the display if called from a
panic context."
I've enhanced this to add a flag to the vc that console layer can set to
indicate they want this behaviour to occur. This also adds support to
fbcon for that flag and adds an fb flag for drivers to indicate they want
to use the support. It enables this for KMS drivers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Expand the crtc_gamma_set function to accept a starting offset. The
reason for this is to eventually use this function for setcolreg from
drm_fb_helper.c. The fbdev colormap function can start at any offset in
the color map.
Signed-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is consistent with trying to access a filename that not exist
within a directory which is a good analogy here. The main reason for the
change is that it is easy to confuse the error code of EBADF as an
performing an ioctl on an invalid file descriptor (rather than an
unknown object).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes lack of power saving with multiple heads on
some desktop cards.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16474
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Change the interface to expect a PTR_ERR specifing the real error code
as opposed to assuming a NULL return => -EINVAL. Just once the user may
not be at fault!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Smatch complained that the ERR_PTR from hwmon_device_register() wasn't
handled. I added some error handling in radeon_hwmon_init() to silence
the warning.
Unfortunately errors from radeon_pm_init() aren't handled so this
doesn't really make a difference beyond silencing the warning.
Also I changed DRM_ERROR() to dev_err() which is the new preferred
method.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
router objects are found on systems that use a mux to control
ddc line to connector routing or to control the actual clock and data
routing from the chip to the connectors. This patch implements ddc line
routing.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Handle asic specific table to hw mappings in
combios_setup_i2c_bus() directly. This allows us
to remove most of the combios quirks and clean up
the i2c bus setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we added i2c buses as needed when enumerating connectors
power management, etc. This only exposed the actual buses used and
could have lead to the same buse getting created more than once if
one buses was used for more than one purpose. This patch sets up
all i2c buses on the card in one place and users of the buses just
point back to the one instance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- buffer offsets in the base regs are 256b aligned so
shift properly when comparing, fixed by Andre Maasikas
- mipmap size was calculated wrong when nlevel=0
- texture bo offsets were used after the bo base address was added
- vertex resource size register is size - 1, not size
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Andre Maasikas <amaasikas@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This hasn't mattered up until the ioctl started using the value, and it fell
apart.
fixes fd.o 29340, Ubuntu LP 606081
[airlied: cleaned up whitespace and don't need an error before pushing]
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
R4xx also uses the atom add connector function, but underscan is only
supported on avivo chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Prior to this patch the code was dividing the src_v by the dst_h
and vice versa, rather than src_v/dst_v and src_h/dst_h.
This could lead to problems in the calculation of the display
watermarks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of /ssd/git/drm-next: (230 commits)
drm/i915: Clear the Ironlake dithering flags when the pipe doesn't want it.
drm/agp/i915: trim stolen space to 32M
drm/i915: Unset cursor if out-of-bounds upon mode change (v4)
drm/i915: Unreference object not handle on creation
drm/i915: Attempt to uncouple object after catastrophic failure in unbind
drm/i915: Repeat unbinding during free if interrupted (v6)
drm/i915: Refactor i915_gem_retire_requests()
drm/i915: Warn if we run out of FIFO space for a mode
drm/i915: Round up the watermark entries (v3)
drm/i915: Typo in (unused) register mask for overlay.
drm/i915: Check overlay stride errata for i830 and i845
drm/i915: Validate the mode for eDP by using fixed panel size
drm/i915: Always use the fixed panel timing for eDP
drm/i915: Enable panel fitting for eDP
drm/i915: Add fixed panel mode parsed from EDID for eDP without fixed mode in VBT
drm/i915/sdvo: Set sync polarity based on actual mode
drm/i915/hdmi: Set sync polarity based on actual mode
drm/i915/pch: Set transcoder sync polarity for DP based on actual mode
drm/i915: Initialize LVDS and eDP outputs before anything else
drm/i915/dp: Correctly report eDP in the core connector type
...
Intel variants don't support it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Logic was:
if (mode0 && mode1)
else if (mode0)
else
Should be:
if (mode0 && mode1)
else if (mode0)
else if (mode1)
Otherwise we may end up calculating the priority regs with
unitialized values.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16492
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I wrote this for the prime sharing work, but I also noticed other external
non-upstream drivers from a large company carrying a similiar patch, so I
may as well ship it in master.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we were not able to map the io bar in device init, don't attempt
to unmap it in device fini. All radeons should have a io bar, so
I doubt this would ever trigger, but just to be on the safe side...
Pointed out by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This interface allows userspace to request hyperz support, it probably
needs more locking, and really reporting that you can have hyperz is racy
since someone else might get it before you do.
v2: modify so we pass 0 valued packets to let DDX/r300c keep working.
also fixed incorrect 0x4f1c reference.
v3: fixup zb_bw_cntl so older drivers keep working
v4: add locking, fixup SC_HYPERZ_EN - patch stream to disable hiz
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We aren't using it, so no need. Save additional dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
group state that is emitted sequentially into fewer packets.
This saves a number of dwords.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use of HDP_*_COHERENCY_FLUSH_CNTL can cause a hang in certain
situations. Add workaround.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We used to limit the rs4xx gart aperture to 32 MB, but I suspect
that was due to not meeting the alignment requirements of the
aperture. This patch should only be applied after:
"drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics"
has been applied.
This patch should probably soak for a bit in d-r-t.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The "error" variable is unsigned so it's never less than zero. I
changed it to check if (freq < current_freq) directly.
"best_error" is also unsigned so "best_error - 100" could be a large
number instead of a negative. Since "error" is unsigned it is never
less than a negative and so the cases where "best_error" is less than or
equal to 100 are false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems using kexec, the new kernel is booted straight from the old kernel, without any warning to the graphics driver. So the GPU is basically left as-is in a running state, however the CPU side is completly reset.
Without stating the saneness of anyone using kexec on live systems, we should at least try not to crash the GPU. This patch resets 3 registers to 0 that could cause bad things to happen to the running system.
This allows kexec to work on a Power6/RN50 system.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a problem where on low VRAM cards we'd run out of space for validation.
[airlied: Tested on my M7, Thinkpad T42, compiz works with no problems.]
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required for the NB_MISC regs on rs780/rs880 which
means HDMI/DVI/DP ports using PCIEPHY won't work without
it. It might also help with s/r (asic init) issues on other
atombios cards.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28774
and similar issues reported by Alberto Milone.
[airlied: Squash io fix patch]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We will need method of selecting encoder that should receive HDMI block. For
now we assign HDMI block to first enabled encoder. Hopefully there are not many
RS6x0 chips with two digital encoders.
[airlied: add RS740 checks as per Alex suggestion.]
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable audio support on devices using polling. In case user
decides to disable audio (module parameter) we still will try to use timer in
r600_audio_enable_polling. This would lead to BUG in kernel/timer.c.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace needs this information to access tiled
buffers via the CPU.
v2: rebased on evergreen accel changes
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check for relocs for DB_DEPTH_INFO, CB_COLOR*_INFO, and texture
resources.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx/rv7xx/evergreen families supported; older asics did
not have an internal thermal sensor.
Note, not all oems use the internal thermal sensor, so it's
only exposed in cases where it is used.
Note also, that most laptops use an oem specific ACPI solution for
GPU thermal information rather than using the internal thermal
sensor directly.
v2: export millidegrees celsius, use hwmon device properly.
v3: fix Kconfig
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
By calling the ATIF method in the radeon driver we can make sure
that hotkeys such as the video switch key emit ACPI events when
pressed.
agd5f: fix warning
Signed-off-by: Alberto Milone <alberto.milone@canonical.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some tables have delays that can cause the timeout to hit
even when not intended.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=27744
and related bugs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Make the logic in r100_pll_errata_after_index() match the other
errata functions
- Use rdev->family rather than rdev->flags & RADEON_FAMILY_MASK for kms
- replace rn50 check using ids with ASIC_IS_RN50 convenience macro
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29062
Reported-by: Andres Cimmarusti <acimmarusti@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Return the crtc_id, not the counter value. They are not
necessarily the same.
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add delay after turning off the LVDS encoder.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16389
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We only add/remove crtcs at driver load, you cannot remove when
the GPU is running a CS packet since the fd is open, when
GPU hotplugging on radeons actually is needed all this locking
needs a review and I've started re-working kms core locking to deal
with this better. But for now avoid long delays in CS processing when
hotplug detect is happening in a different thread.
this fixes a regression introduced with hotplug detection.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disables the crts as per dpms and also disables the ppll
associated with the crtc. This should save additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reported-by: Alexander Y. Fomichev <git.user@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connector is actually DVI rather than HDMI.
Reported-by: trapDoor <trapdoor6@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a regression caused by b2ea4aa67b
due to the way shared ddc with multiple digital connectors was handled.
You generally have two cases where DDC lines are shared:
- HDMI + VGA
- HDMI + DVI-D
HDMI + VGA is easy to deal with because you can check the EDID for the
to see if the attached monitor is digital. A shared DDC line with two
digital connectors is more complex. You can't use the hdmi bits in the
EDID since they may not be there with DVI<->HDMI adapters. In this case
all we can do is check the HPD pins to see which is connected as we have
no way of knowing using the EDID.
Reported-by: trapdoor6@gmail.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The asics in question have the following requirements with regard to
their gart setups:
1. The GART aperture size has to be in the form of 2^X bytes, where X is from 25 to 31
2. The GART aperture MC base has to be aligned to a boundary equal to the size of the
aperture.
3. The GART page table has to be aligned to the boundary equal to the size of the table.
4. The GART page table size is: table_entry_size * (aperture_size / page_size)
5. The GART page table has to be allocated in non-paged, non-cached, contiguous system
memory.
This patch takes care 2. The rest should already be handled properly.
This fixes a regression noticed by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check ulBootUpMemoryClock on AMD IGPs.
Fix regression noticed by Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-platform:
drm: Make sure the DRM offset matches the CPU
drm: Add __arm defines to DRM
drm: Add support for platform devices to register as DRM devices
drm: Remove drm_resource wrappers
Connectors with a shared ddc line can be connected to different
encoders.
Reported by Pasi Kärkkäinen <pasik@iki.fi> on dri-devel
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some RV100 cards with 2 VGA ports show up with DVI+VGA, however
some boards with DVI+VGA have the same subsystem ids. Better
to have a VGA port show up as DVI than having a non-useable
DVI port.
reported by DHR in irc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is a regression from 2.6.34 related to the recent radeon power
management changes, caused by attempting to cancel a delayed work
item that's never been scheduled. However, the code as is has some
other issues potentially leading to visible problems.
First, the mutex around cancel_delayed_work() in radeon_pm_suspend()
doesn't really serve any purpose, because cancel_delayed_work() only
tries to delete the work's timer. Moreover, it doesn't prevent the
work handler from running, so the handler can do some wrong things if
it wins the race and in that case it will rearm itself to do some
more wrong things going forward. So, I think it's better to wait for
the handler to return in case it's already been queued up for
execution. Also, it should be prevented from rearming itself in that
case.
Second, in radeon_set_pm_method() the cancel_delayed_work() is not
sufficient to prevent the work handler from running and queing up
itself for the next run (the failure scenario is that
cancel_delayed_work() returns 0, so the handler is run, it waits on
the mutex and then rearms itself after the mutex has been released),
so again the work handler should be prevented from rearming itself in
that case..
Finally, there's a potential deadlock in radeon_pm_fini(), because
cancel_delayed_work_sync() is called under rdev->pm.mutex, but the
work handler tries to acquire the same mutex (if it wins the race).
Fix the issues described above.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some IGP systems specify the system memory clock in the Firmware
table rather than the IGP info table. Check both and make sure
we have a value system memory clock value.
v2: make sure rs690_pm_info is called on rs780/rs880 as well.
fixes a regression since 07d4190327b02ab3aaad25a2d168f79d92e8f8c2.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For some reason on resume, executing the BIOS scripts locks up the whole chipset, by avoiding the dynclk table the machine resumes properly and seems to function okay.
Signed-off-by: Dave Airlie <airlied@redhat.com>
They don't have an atombios so don't attempt to use it for
eng/mem clocks.
Reported by spoonb on #radeon
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28671
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
HDP non surface should cover the whole VRAM but we were misscomputing
the size and we endup in some case not covering the VRAM at all (if
VRAM size were > 1G). Covering more than the VRAM size shouldn't be
an issue.
Fix : https://bugs.freedesktop.org/show_bug.cgi?id=28016
[airlied: add evergreen fix]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since the VGA switcheroo, we'd attempt to read the BIOS from VRAM on startup
but on some unposted cards this can cause hangs/crashes.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=28592
(further problem pointed out by agd5f on IGP systems)
Reported-by: Reilithion on #radeon
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were returning 0 in both the success and failure paths. Noticed while
investigating FDO bug 26403.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This needs similar handling to other compressed textures.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Code did not handle projected 2d and depth coordinates, meaning potentially
set 3d or cube special handling might stick.
(Not sure what depth coord actually does, but I guess handling it
like a normal coordinate is the right thing to do.)
Might be related to https://bugs.freedesktop.org/show_bug.cgi?id=26428
Signed-off-by: sroland@vmware.com
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=28459
agd5f: apply to r1xx/r2xx as well.
Signed-off-by: Roland Scheidegger <sroland@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This works well enough on a js21, but it would be nice if IBM could supply
more tables for the later Power6/7 machines.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The transmitter needs to be enabled before the link is trained.
Reported-By: Lars Doelle <lars.doelle@on-line.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When suspending, we turn the display hw off, at resume the screen will stay black.
This patch turn it on. Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16180
Signed-off-by: Cedric Godin <cedric.godin@skynet.be>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Installing 2.6.34 on a Power5/rn50 combo machine, X showed buggy sw rendering,
enabling tiling in the DDX fixed it. Investigation showed that a further /16
was needed in the untiled case on this chipset. Need further investigations
on what other chips this could affect, possibly rv100->rv280.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Plugged in FireMV with the rv250 on it, and the second crtc/dac didn't work,
we were reading/writing different registers than we were modifying in the code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
So when we added output polling, we'd suddenly use this code more often, and the fact that it always takes over crtc2 and messes with it during probing isn't what we really want to be happening. A more complete fix would to change it to use whatever crtc was free at the time, but for now lets stay simple and just don't poll if crtc2 is already in use.
Although a more correct fix was found I suspect we should do this as well, until we get a chance to readdres the tv out polling issues.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We really don't want to be polling tv-out but since we weren't forcing the
i2c lines to invalid (tv-out has no DDC), we were adding tv connectors to the
polling setup and this was causing blinking on secondary displays.
This fixes the regression Torsten reported.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes FDO bug #28375, it's kind of regression, so quite important to have
it for .35.
V2: Fix on RV770+ as well. All other chipsets have only one clock mode per
state.
V3: I'm out of luck today. Grepped for voltage in r*.c and missed evergreen.
agd5f: rebased
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
track the current voltage level and avoid setting it
if the requested voltage is already set.
v2: check voltage type before checking current voltage
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vddc value in the power tables is not an actual voltage
like on discrete r6xx/r7xx/evergreen systems, but instead has
a symbolic meaning (e.g., NONE, LOW, HIGH, etc.). See atombios.h
Most RS780/RS880 vbioses don't have a SetVoltage table anyway,
so it shouldn't be doing anything to the hardware at the moment.
I need to figure out how voltage is supposed to work on the newer
IGPs; until then, disable it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds an additional profile, mid, to the pm profile
code which takes the place of the old low profile. The default
behavior remains the same, e.g., auto profile now selects between
mid and high profiles based on power source, however, you can now
manually force the low profile which was previously only available
as a dpms off state. Enabling the low profile when the displays
are on has been known to cause display corruption in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- don't rest the power state in pm_init()
We already boot up to the default power state. Note this
patch relies on:
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
To make sure the default power state matches the boot up state.
- In the pm resume path asic init will have set the power state
back to the default so reset the tracking state values.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed to enable accel in the ddx. However,
due to a bug in older versions of the ddx, it relies
on accel being disabled in order to load properly on
evergreen chips. To maintain compatility, we add a new
get accel param and call that from the ddx. The old one
always returns false for evergreen cards.
[this fixes a regression with older userspaces on newer kernels].
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
PM attemps to unmap objects that aren't actually mapped into userspace ever,
so just don't bother unmapping them at this point, since all you are doing
is nothing. We should be making sure all access to these objects are locked in
kernel space instead. In theory the VRAM gart table is already done, and both
the shaders and stolen vga memory blocks are never accessed at runtime.
fixes: https://bugzilla.kernel.org/show_bug.cgi?id=16127
Reported-by: Jure Repnic <jlp.bugs@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.
I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
drm/radeon/kms: make sure display hw is disabled when suspending
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
drm/vmwgfx: Fix framebuffer modesetting
drm/vmwgfx: Fix vga save / restore with display topology.
vgaarb: use MIT license
vgaarb: convert pr_devel() to pr_debug()
drm: fix typos in Linux DRM Developer's Guide
drm/radeon/kms/pm: voltage fixes
drm/radeon/kms/pm: radeon_set_power_state fixes
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
drm/radeon/kms/evergreen: add initial CS parser
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
drm/nv50: cast IGP memory location to u64 before shifting
drm/ttm: Fix ttm_page_alloc.c
drm/ttm: Fix cached TTM page allocation.
drm/vmwgfx: Remove some leftover debug messages.
...
Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The default power state does not always match the default clocks and voltage
for a particular card. The information in the firmware info table is correct
and should be used in preference to the info the default power state.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- This enables voltage adjustment on r6xx+ and certain
r5xx asics.
- Voltage drop support is already available for most
r1xx-r5xx asics.
V2: endian fix for voltage table.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Advanced validation is not implemented yet.
The mesa code that uses this will be released soon.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allow platform devices without PCI resources to be DRM devices.
[airlied: fixup warnings with dev pointers]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Remove the drm_resource wrappers and directly use the
actual PCI and/or platform functions in their place.
[airlied: fixup nouveau properly to build]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
airlied -> brown paper bag.
I blame Hi-5 or the Wiggles for lowering my IQ, move the fix inside some
brackets instead of breaking everything in site.
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least 'make CONFIG_DEBUG_SECTION_MISMATCH=y' causes
drivers/gpu/drm/radeon/atombios_crtc.c: In function 'atombios_crtc_set_pll':
drivers/gpu/drm/radeon/atombios_crtc.c:684: warning: 'pll' may be used uninitialized in this function
which has the looks of a falso positive.
Add a default: case so that gcc rests assured that all possible pll_id's are covered.
Keep the present cases that fall through to the default one for self-documentation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/nouveau/nv40_graph.c: In function `nv40_graph_init':
drivers/gpu/drm/nouveau/nv40_graph.c:400: warning: the frame size of 1184 bytes is larger than 1024 bytes
drivers/gpu/drm/radeon/radeon_atombios.c: In function `radeon_get_atom_connector_info_from_supported_devices_table':
drivers/gpu/drm/radeon/radeon_atombios.c:857: warning: the frame size of 1872 bytes is larger than 1024 bytes
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think it's good to release the AGP bridge at suspend
and reacquire it at resume. Also fix :
https://bugzilla.kernel.org/show_bug.cgi?id=15969
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
This saves some more power at the expense of performance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon needs power supply to get correct PM info so select it at the radeon
level not at the kms option.
Signed-off-by: Dave Airlie <airlied@redhat.com>
list reservation was too optimistic about ttm object reservation
and could think that an object reserved by some other process
as reserved by the list reservation which was false. Thus when
unreserving the list it might unreserve object that it didn't
reserved in the list. Sorry if it's hard to follow but this
kind of things are just causing headheck.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes AGP initialization failure with Apple UniNorth bridges due to trying to
ioremap() normal RAM.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some LVDS connectors don't have a ddc bus, so reset the
ddc bus to invalid before parsing the next connector
to avoid using stale ddc bus data. Should fix
fdo bug 28164.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
This patch is a combination of the previous two profile
patches, but without the index bugs. It cleans up and
fixes some issues with pm profile setup on r6xx chips.
Some tables have different orderings for the power states,
also, r600 only has 1 clock mode per power state. On
desktop cards there are no battery modes, so the low and high
power states are the same. For the low profile case, choose
the lower clock mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- disable gui idle interrupt use
Seems to hang some r5xx chips
- move vbl range check into
existing vbl check function in
radeon_pm.c
- disable crtc mc acccess for the
whole reclocking process
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This seems to be relatively stable now, so enable it for these chipsets
too.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With luck, dynamic memory reclocking on r600 should be stable with
the previous patches. Enable it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm bo workqueue may touch objects while we're reclocking, so make
sure it's blocked until we're done.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to block the drm core from doing anything that may touch our vram
during reclock, so take the drm mutex for the duration.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's a moderate amount of effort involved in setting the card up for
clock transitions, so unify the codepaths to make it easier to implement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add two new sysfs attributes:
- dynpm
- power_state
Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences. dynpm only scales sclk dynamically in single head
mode.
Echoing x.y to power_state selects a static power state (x) and clock
mode (y). This allows you to statically select a power state and clock
mode. Selecting a static clock mode will disable dynpm.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- pm_misc() - handles voltage, pcie lanes, and other non
clock related power mode settings. Currently disabled.
Needs further debugging
- pm_prepare() - disables crtc mem requests right now.
All memory clients need to be disabled when changing
memory clocks. This function can be expanded to include
disabling fb access as well.
- pm_finish() - enable active memory clients.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- remove non_clock_info struct
- track power state misc flags
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just adds overhead when the power state will never change.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hook the atom table parsing up to module loading, so we can automatically
load the appropriate hwmon drivers.
Based on initial patch for r6xx from Matthew Garrett
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.
Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).
(v2) Update for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On pre-r6xx, the power mode array is usually ordered:
low
...
high
default
On r6xx+:
default
low
...
high
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
set proper wait condition as noted by Rafał Miłecki.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Useful for certain power management operations. You
need to wait for the GUI engine (2D, 3D, CP, etc.) to be
idle before changing clocks or adjusting engine parameters.
(v2) Fix gui idle enable on pre-r6xx asics
(v3) The gui idle interrrupt status bit is permanently asserted
on pre-r6xx chips, but the interrrupt is still generated.
workaround it in the driver.
(v4) Add support for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check to see if the GUI engine and related blocks
(2D, 3D, CP, etc) are idle or not. There are a number
of cases when we need to know if the drawing engine
is busy.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm
crtc id. Bump the minor version so userspace can enable conditionaly
features depend on this.
V2 use num_crtc and avoid DRM_ERROR
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes LVDS issues on some laptops; notably laptops with
2048x1536 panels.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit b4fe945405 introduced 3 bugs,
fix them:
* Use the right command dword for second packet offset in
RADEON_CNTL_PAINT/BITBLT_MULTI.
* Don't leak memory if drm_buffer_copy_from_user() fails.
* Don't call drm_buffer_unprocessed() unless drm_buffer_alloc() and
drm_buffer_copy_from_user() have been called successfully first.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/radeon/r300.c
The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.
Previously we just set them to dpms off. This should save
additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bring radeon up to speed with the async event synchronization for
drmWaitVblank. See c9a9c5e02a for
more information. Without this patch event never get delivered
to userspace client.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/legacy: only enable load detection property on DVI-I
drm/radeon/kms: fix panel scaling adjusted mode setup
drivers/gpu/drm/drm_sysfs.c: sysfs files error handling
drivers/gpu/drm/radeon/radeon_atombios.c: range check issues
gpu: vga_switcheroo, fix lock imbalance
drivers/gpu/drm/drm_memory.c: fix check for end of loop
drivers/gpu/drm/via/via_video.c: fix off by one issue
drm/radeon/kms/agp The wrong AGP chipset can cause a NULL pointer dereference
drm/radeon/kms: r300 fix CS checker to allow zbuffer-only fastfill
DVI-D doesn't have analog. This matches the avivo behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should duplicate exactly what the ddx does for both
legacy and avivo.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This change makes the array larger, "MAX_SUPPORTED_TV_TIMING_V1_2" is 3
and the original size "MAX_SUPPORTED_TV_TIMING" is 2.
Also there were checks that were off by one.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Selecting the wrong or no CONFIG_AGP_* chipset can cause a NULL pointer
dereference when combined with CONFIG_DRM_RADEON_KMS and an old system
with a R100 AGP card (should effect other cards too). The agp field
will be set to NULL if no suitable AGP chipset driver is loaded,
drm_agp_acquire already preforms a suitable NULL check so it can be used
directly.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Fix sparc regression in r300_scratch()
drm: make sure vblank interrupts are disabled at DPMS time
drm/radeon/kms/evergreen: No EnableYUV table
drm/radeon: 9800 SE has only one quadpipe
drm/radeon/kms: don't print error for legal crtcs.
drm/radeon/kms/evergreen: fix LUT setup
Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.
Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit b4fe945405 ("drm/radeon: Fix
memory allocation failures in the preKMS command stream checking.")
added a regression in that it completely tossed the get_unaligned()
done by r300_scratch() which we added in commit
958a6f8ccb ("drm: radeon: Fix unaligned
access in r300_scratch().").
Put it back.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-ttm-unmappable:
drm/radeon/kms: enable use of unmappable VRAM V2
drm/ttm: remove io_ field from TTM V6
drm/vmwgfx: add support for new TTM fault callback V5
drm/nouveau/kms: add support for new TTM fault callback V5
drm/radeon/kms: add support for new fault callback V7
drm/ttm: ttm_fault callback to allow driver to handle bo placement V6
drm/ttm: split no_wait argument in 2 GPU or reserve wait
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bo.c
This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.
V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.
V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM
[airlied- squashed driver removals in here also]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.
V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly
kfree(gem_obj);
in every gem driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-radeon-evergreen-accel:
drm/radeon: fix cypress firmware typo.
drm/radeon/kms/evergreen: add hpd support
drm/radeon/kms/evergreen: implement irq support
drm/radeon/kms/evergreen: setup and enable the CP
drm/radeon/kms/evergreen: implement gfx init
drm/radeon/kms/evergreen: add soft reset function
drm/radeon/kms/evergreen: add gart support
drm/radeon/kms: add support for evergreen power tables
drm/radeon/kms: update atombios.h power tables for evergreen
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* drm-edid-fixes:
drm/edid: When checking duplicate standard modes, walked the probed list
drm/edid: Fix sync polarity for secondary GTF curve
drm/modes: Fix interlaced mode names
drm/edid: Add secondary GTF curve support
drm/edid: Strengthen the algorithm for standard mode codes
drm/edid: Fix the HDTV hack.
drm/edid: Extend range-based mode addition for EDID 1.4
drm/edid: Add test for monitor reduced blanking support.
drm/edid: Fix preferred mode parse for EDID 1.4
drm/edid: Remove some silly comments
drm/edid: Remove arbitrary EDID extension limit
drm/edid: Add modes for Established Timings III section
drm/edid: Reshuffle mode list construction to closer match the spec
drm/edid: Remove a redundant check
drm/edid: Remove some misleading comments
drm/edid: Fix secondary block fetch.
* drm-ttm-pool:
drm/ttm: using kmalloc/kfree requires including slab.h
drm/ttm: include linux/seq_file.h for seq_printf
drm/ttm: Add sysfs interface to control pool allocator.
drm/ttm: Use set_pages_array_wc instead of set_memory_wc.
arch/x86: Add array variants for setting memory to wc caching.
drm/nouveau: Add ttm page pool debugfs file.
drm/radeon/kms: Add ttm page pool debugfs file.
drm/ttm: Add debugfs output entry to pool allocator.
drm/ttm: add pool wc/uc page allocator V3
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On X startup we were getting a flicker where there shouldn't have been one.
the X DDX calls the kernel to set the properties to the same values (yes
it could be smarter), however the kernel was doing a pointless modeset then,
making my nice smooth boot ugly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
shr/shl ops need the full dst rather than the pre-masked
version. Fixes fdo bug 27478 and kernel bug 15738.
v2: remove some unsed vars, add comments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (29 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
The command processor (CP) fetches command buffers and
feeds the GPU. This patch requires the evergreen
family me and pfp ucode files.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initializes the gfx engine so accel can
eventually be used.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gart setup is more or less like r7xx. Copy
rv770d.h to evergreend.h and fix up changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is case where we want to be able to wait only for the
GPU while not waiting for other buffer to be unreserved. This
patch split the no_wait argument all the way down in the whole
ttm path so that upper level can decide on what to wait on or
not.
[airlied: squashed these 4 for bisectability reasons.]
drm/radeon/kms: update to TTM no_wait splitted argument
drm/nouveau: update to TTM no_wait splitted argument
drm/vmwgfx: update to TTM no_wait splitted argument
[vmwgfx patch: Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch is against the drm-fbdevfix1 branch. It removes the
drm_fb_helper_setcolreg function. The reason is that fb_setcolreg is only
used in the case where fb_setcmap is called and no fb_ops->fb_setcmap is
used. In the drm case we always need a fb_setcmap hook to handle multiple
crtcs so we don't need a fb_setcolreg hook. Please apply.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
a) slow work is always used now for any fbcon hotplug, as its not
a fast task and is more suited to being ran under slow work.
b) attempt to not do any fbdev changes when X is running as we'll
just mess it up. This hooks set_par to hopefully do the changes
once X hands control to fbdev.
This also adds the nouveau/intel hotplug support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we are running in a headless environment we have no idea what
output the user might plug in later, we only have hotplug detect
from the digital outputs. So if we detect no connected outputs at
initialisation, start a slow work operation to poll every 5 seconds
for an output.
this is only hooked up for radeon so far, on hw where we have full
hotplug detection there is no need for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.
All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.
Fixes from James Simmons and Ben Skeggs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some vbios dac_adj tables are all zeros. Check for that
case and use the default table if so.
Should fix fdo bug 27478.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- make sure legacy dac1 has an enc priv
- remove unused num var
- no need for extra tv_dac var in atom dac functions
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fix formatting
- clean up tv_dac_cntl handling for tv
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an unlikely memory leak, but we may as well fix it. It's easy
to fix and every static checker will complain if we don't.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
bad cast was overwriting the tvdac adj values
Fixes fdo bug 27478
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm_page_pool file is hooked ttm_page_alloc_debugfs for pool
allocator state.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
of the times but once in a while it fails for no obvious
reasons (same status than previous reset just no same
happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
it seems that it can fail after a bunch (reset every
2sec for 3hour bring down the GPU & computer)
This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).
Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.
Next step is to record the bogus command that leaded to
the lockup.
V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch cleanup the fence code, it drops the timeout field of
fence as the time to complete each IB is unpredictable and shouldn't
be bound.
The fence cleanup lead to GPU lockup detection improvement, this
patch introduce a callback, allowing to do asic specific test for
lockup detection. In this patch the CP is use as a first indicator
of GPU lockup. If CP doesn't make progress during 1second we assume
we are facing a GPU lockup.
To avoid overhead of testing GPU lockup frequently due to fence
taking time to be signaled we query the lockup callback every
500msec. There is plenty code comment explaining the design & choise
inside the code.
This have been tested mostly on R3XX/R5XX hw, in normal running
destkop (compiz firefox, quake3 running) the lockup callback wasn't
call once (1 hour session). Also tested with forcing GPU lockup and
lockup was reported after the 1s CP activity timeout.
V2 switch to 500ms timeout so GPU lockup get call at least 2 times
in less than 2sec.
V3 store last jiffies in fence struct so on ERESTART, EBUSY we keep
track of how long we already wait for a given fence
V4 make sure we got up to date cp read pointer so we don't have
false positive
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GPIO_I2C_INFO table does not always have
ATOM_MAX_SUPPORTED_DEVICE entries. Limit
the number of indices to the size of the
table.
Should fix Novell bug 589022.
v2: fix typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some GPUs have an APM/ACPI PM mode selection switch and some BIOSes
set this to APM. We really want this in ACPI mode for Linux.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we resume in a bad way, we'll get 0xffffffff in wptr, and then
oops with no console. This just adds a sanity check so that we can
avoid the oops and hopefully get more details out of people's systems.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Turn off hw i2c by default except for mm i2c which
is hw only until we sort out the remaining prescale
issues on older chips. hw i2c can be enabled with
hw_i2c=1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows us to remove the internal bit algo bus used by
the radeon i2c algo. We now register a radeon algo adapter
if the gpio line is hw capable and the hw inplementation is
available, otherwise we register a bit algo adapter.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Doesn't seem to work reliably and the pci quirks don't
always work.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Add module option to force the display priority
0 = auto, 1 = normal, 2 = high
- Default to high on r3xx/r4xx/rv515 chips
Fixes flickering problems during heavy acceleration
due to underflow to the display controllers
- Fill in minimal support for RS600
v2 - update display priority when bandwidth is updated
so the user can change the parameter at runtime and it
will take affect on the next modeset.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems have LCD* rather than DFP* device tags in the bios
for eDP connectors; notably the new apple iMac. This fixes
things up so eDP connectors with either tag will work.
v2: fix typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like a copy/paste typo from when evergreen support
was added.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- 8 lane links are not valid for DP
- remove unused num var
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This prevented radeon.test=1 from testing transfers from/to GTT beyond the
visible VRAM size.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- remove a few more drm only regs
- remove sampler, alu, bool, loop constant regs.
They are set via separate packet3's already
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Drop some more safe regs taht userspace shouldn't hit
- Constant base regs need relocs. This allows us to use
constant buffers rather than the constant register file.
Also we don't want userspace to be able to set arbitrary
mc base values for the const caches.
- Track SQ_CONFIG so we know whether userspace is using
the cfile or constant buffers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When there is allocation failure in radeon_cs_parser_relocs parser->nrelocs
is not cleaned. This causes NULL pointer defeference in radeon_cs_parser_fini
when clean up code is trying to loop over the relocation array and free the
objects.
Fix adds a check for a possible NULL pointer in clean up code.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_gart_fini might call GART unbind callback function which
might try to access GART table but if gart_disable is call first
the GART table will be unmapped so any access to it will oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get this if the user moves the mouse when we are waiting to move
some stuff around in the validate. Don't fail.
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check that atom cmd and data tables are valid
before using them.
(v2)
- fix some whitespace errors noticed by Rafał Miłecki
- check a few more cases
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- no longer needed with the latest new pll algo fixes.
- also don't use lcd pll limits. They don't seem
to work well for all systems. If we have a case where
they are useful, we can set the flag for that case.
fixes fdo bug 27083
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I missed rs4xx in 7f1e613daf0fdd0884316ab25a749db3c671329e
Fixes fdo bug 27219.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
RS4xx+ IGP chips use an internal gart, however,
some of them have the agp cap bits set in their pci
configs. Make sure to clear the AGP flag as AGP will
not work with them.
Should fix fdo bug 27225
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- rs780/880 were using the wrong bandwidth functions
- convert r1xx-r4xx to use the same pm sclk/mclk structs as
r5xx+
- move bandwidth setup to a common function
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes some issues with the last gfx init patch.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Look up i2c bus in the power table and expose it.
You'll need to load a hwmon driver for any chips
on the bus, this patch just exposes the bus.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
AMD says in section 2.5.4 (GFX MSI Enable) of #43291 (AMD 780G Family
Register Programming Requirements):
The SBIOS must enable internal graphics MSI capability in GCCFG by
setting the following: NBCFG.NB_CNTL.STRAP_MSI_ENABLE='1'
Quite a few BIOS writers misinterpret this sentence and think that
enabling MSI is an optional feature. However, clearing that bit just
prevents delivery of MSI messages but does not remove the MSI PCI
capabilities registers, and so leaves these devices unusable for any
driver that attempts to use MSI.
Setting that bit is not possible after the BIOS has locked down the
configuration registers, so we have to manually disable MSI for the
affected devices.
This fixes the codec communication errors in the HDA driver when
accessing the HDMI audio device, and allows us to get rid of the
overcautious quirk in radeon_irq_kms.c.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Alex Deucher <alexdeucher@gamil.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This just an example to show what radeon_asic.h might be good for.
Before Jerome kills it ;)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In essence this creates a home for all asic specific declarations in
radeon_asic.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With these static structs gone, radeon_asic.h is a real header file
and can be used as such.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
And move asic init plus a few related functions from radeon_device.c
to it. This file will hold all the asic structures in the future,
but atm they're still stuck in radeon_asic.h.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We tried to implement interruptible waiting with timeout (it was broken
anyway) which was not a good idea as explained by Andrew. It's possible
to avoid using additional variable but actually it inroduces using more
complex in-kernel tools. So simply add one variable for condition.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R6xx+ cards need to use the 3D engine to blit data which requires
quite a bit of hw state setup. Rather than pull the whole 3D driver
(which normally generates the 3D state) into the DRM, we opt to use
statically generated state tables. The regsiter state and shaders
were hand generated to support blitting functionality. See the 3D
driver or documentation for descriptions of the registers and
shader instructions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We still have many magic numbers in HDMI/audio to define
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Older GPUs are little different, HDMI blocks are not hard-wired, but routable.
We should just find some free HDMI block and route it to choosen encoder. In
case of RS6x0 there is only one HDMI block, we don't enable HDMI on RS6x00 yet
however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We almost always used first HDMI block for first encoder and second for sencod.
Exception was KLDSCP_LVTMA. Analyzing code picking DIG encoder shows the same
behaviour. It shows HDMI block are related to DIGs, which relation we now use.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already know same offsets are used for different encoders/transmitters, so
just numeric them instead naming incorrectly. Additionaly we found additional
registers needed for RV770+
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixing the i2c prescale in the last patch
gets it working on r1xx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
use the i2c pads to drive SDA
Possible fix for fdo bug 26430
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on ddx patch by Andrzej Hajda.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adjust modeset ordering to fix spread spectrum.
The spread spectrum command table relies on the
crtc routing to already be set in order to work
properly on some asics.
Should fix fdo bug 25741.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The bios has alternate pll output limits for LCD panels.
If available, use these for pll divider calculations.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The atom spread spectrum table does not always
disable ss. Explicitly disable it and then use
the atom table to enable later if needed (currently
only used for LVDS).
Fixes display issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In somecase the atombios code might lead to infinite loop because
the GPU is in broken state, this patch track the jump history and
will abort atombios execution if we are stuck executing the same
jump for more than 1sec. Note that otherwise in some case we might
enter an infinite loop in the kernel context which is bad.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (151 commits)
vga_switcheroo: disable default y by new rules.
drm/nouveau: fix *staging* driver build with switcheroo off.
drm/radeon: fix typo in Makefile
vga_switcheroo: fix build on platforms with no ACPI
drm/radeon: Fix printf type warning in 64bit system.
drm/radeon/kms: bump the KMS version number for square tiling support.
vga_switcheroo: initial implementation (v15)
drm/radeon/kms: do not disable audio engine twice
Revert "drm/radeon/kms: disable HDMI audio for now on rv710/rv730"
drm/radeon/kms: do not preset audio stuff and start timer when not using audio
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
...
Fixed trivial conflicts in drivers/gpu/vga/Kconfig
radeon was always including the atpx code unnecessarily, also core
switcheroo was including acpi headers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Type of iterator was promoted to unsigned long in 64bit systems.
*header is small structure so it is alwas safe to cast return value
of sizeof operator to int.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit "disabled" audio on RV710 and RV740 only, leaving RV770 and RV730.
The order is: CHIP_RV770 < CHIP_RV730 < CHIP_RV710 < CHIP_RV740.
It is not needed anway, as we do not even try to enable audio on RV770 and
newer. We call initializing function in r600.c only, not in rv770.c.
If there is something causing green tinges, it's HDMI mode setting for encoder
and I will try to debug that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-testing' of /ssd/git/drm-radeon-next:
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
radeon's have a special ability to passthrough writes in their internal
memory space directly to PCI, this ability means that if some of the internal
surfaces like the depth buffer point at 0x0, any writes to these will
go directly to RAM at 0x0 via PCI busmastering.
Now mesa used to always emit clears after emitting state, since the
radeon mesa driver was refactored a year or more ago, it was found it
could generate a clear request without ever sending any setup state to the
card. So the clear would attempt to clear the depth buffer at 0x0, which
would overwrite main memory at this point. fs corruption ensues.
Also once one app did this correctly, it would never get set back to 0
making this messy to reproduce.
The kernel should block this from happening as mesa runs without privs,
though it does require the user be connected to the current running X session.
This patch implements a check to make sure the depth offset has been set
before a depth clear occurs and if it finds one it prints a warning and
ignores the depth clear request. There is also a mesa fix to avoid sending
the badness going into mesa.
This only affects r100/r200 GPUs in user modesetting mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 asic was missing set_surface_reg callback leading to
oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
The whole attribute table is valid for
shr/shl ops.
Fixes fdo bug 26668
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add support for pre-avivo chips
- add support for fixed post/ref dividers
- add support for non-fractional fb dividers
By default avivo chips use the new algo and
pre-avivo chips use the old algo. Use the "new_pll"
module option to toggle between them.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
AtomBIOS tables on non-mobility GPU do not contain POWERSAVE/BATTERY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We kept pointers to requested and current clock modes in every power state.
That was useless, more /global/ pointers in power struct are enough.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- updated swizzle modes for backend map setup
- fix programming of a few gfx regs
- properly handle pipe/backend setup on LE cards
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Version 2 of memory controller did break the initialization for
R3XX/R4XX hardware. This patch fix it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a check on avivo chips to see if we are in the VBL
region for the active crtcs when we trigger the engine change.
I appear to have glitches locally on pm transistion (not sure all
fixes are in yet) and this at least seems to be correct here,
maybe others can test on systems with no glitches.
Allocation of single large block of memory may fail under memory
presure. drm_buffer object can hold one large block of data in
multiple independ pages which preents alloation failures.
This patch converts all access to command stream to use drm_buffer
interface. All direct access to array has to go tough drm_buffer
functions to get correct pointer.
Outputting the command stream to ring buffer needs to be awear of
the split nature of drm_buffer. The output operation requires the
new OUT_RING_DRM_BUFFER.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just compare the i2c id since the i2c structs
may be slighly different.
Fixes fdo bug 26616.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 board lists DVI port as HDMI.
Fixes fdo bug 26605
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For usec delays use udelay instead of scheduling, this should
allow reclocking to happen faster. This also was the cause
of reported 33s delays at bootup on certain systems.
fixes: freedesktop.org bug 25506
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.
Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880
RPB: resume previously broken
V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r200 cards have dma engine which can be used to tranfer data
between vram and system memory.
r300 dma engine registers match r200 dma engine. Enabling
dma copy for r200 is simple as hooking r200 asic to already
existing function r300_copy_dma.
Rename r300_dma_copy to r200_dma_copyto reflect that supports
starts from r200 cards.
v2: Created a new asic object for r200 cards.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Setting global asic structure to point to different function
would cause problem in system where is multiple r300 cards
with different bus type.
r300_asic_pcie is just copy from r300_asic with gart tlb
functions replaced with pcie versions.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r6xx/r7xx use the rs600 variant. This old one just
confuses things.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should stop audio-state-reading timer before we turn off engine
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_track_check’:
drivers/gpu/drm/radeon/r600_cs.c:166: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:166: note: ‘bpe’ was declared here
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_parse’:
drivers/gpu/drm/radeon/r600_cs.c:938: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:938: note: ‘bpe’ was declared here
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In testing I've never seen it go past 1 retry anyways but better
safe than sorry.
Reported by Droste on irc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noticed on a DEC Alpha.
Start up into console mode caused 15 unaligned accesses, and starting X
caused another 48.
Signed-off-by: Matt Turner <mattst88@gmail.com>
CC: Jerome Glisse <jglisse@redhat.com>
CC: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is partial revert of commit 9404c9c392d5 ("Fix misspelling of "should"
and "shouldn't" in comments"). According to Dave Airlie:
"Can we drop any cleanups to atombios.h? This file comes from
AMD and we normally drop it into place, so they just get overwritten
next time."
Reported-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
radeon_cs kfree the tracker structure but for r6xx/r7xx we want
to kfree it inside the parse function because we share it with
the UMS code path. Set tracker to NULL after freeing it will
avoid double free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this uses a new entrypoint to invalidate gart entries instead of using 0.
Changed to rather than pointing to 0 address point empty entry to dummy
page. This might help to avoid hard lockup if for some wrong
reasons GPU try to access unmapped GART entry.
I'm not 100% sure this is going to work, we probably need to allocate
a dummy page and point all the GTT entries at it similiar to what AGP does.
but we can test this first I suppose.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's happened time and time again (most recently with the support for EDID
hardcoded in the BIOS ROM) that new code didn't check for rdev->bios being
non-NULL before triggering dereferences of it. This would result in an
oops/panic on setups with no BIOS ROM. Hopefully this central test will be
more robust.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch add cs checker to r600/r700 hw. Command stream checking
will rewrite some of the cs value in order to restrict GPU access
to BO size. This doesn't break old userspace but just enforce safe
value. It should break any things that was using the r600/r700 cs
ioctl to do forbidden things (malicious software), though we are
not aware of such things.
Here is the list of thing we check :
- enforcing resource size
- enforcing color buffer slice tile max, will restrict cb access
- enforcing db buffer slice tile max, will restrict db access
We don't check for shader bigger than the BO in which they are
supposed to be, such use would lead to GPU lockup and is harmless
from security POV, as far as we can tell (note that even checking
for this wouldn't prevent someone to write bogus shader that lead
to lockup).
This patch has received as much testing as humanly possible with
old userspace to check that it didn't break such configuration.
However not all the applications out there were tested, thus it
might broke some odd, rare applications.
[airlied: fix rules for cs checker for parallel builds]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mostly obvious simplifications.
The i915 pread/pwrite ioctls, intel_overlay_put_image and
nouveau_gem_new were incorrectly using the locked versions
without locking: this is also fixed in this patch.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-linus' of ../drm-next:
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/radeon/kms: fix screen clearing before fbcon.
drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
drm/radeon/kms: change Kconfig text to reflect the new option.
drm/radeon/kms: suspend and resume audio stuff
ATOM appears to return 0x20 which seems to mean some sort of timeout.
retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>
original evergreen patches we against a kernel tree
without my radeon i2c algo changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a typo in crtc offset setup that set the crtc
instances wrong for all crtcs except the first.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pre-pcie chips seem to use the reference clock
rather than the sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_copy_dma is only available for r200 or newer cards.
Call to radeon_copy_dma would result to NULL pointer
dereference if benchmarking asic without dma engine.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This memset_io was added to debug something way back and got
left behind, memset the fb to black so the borders don't be all white.
Signed-off-by: Dave Airlie <airlied@redhat.com>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.
Major changes are DCE4 handling for PLLs for the > 2 crtcs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This merges ugly whitespace we want to keep for consistency
along with the latest upstream changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add an utilities function radeon_ib_bogus_add which will
save an ib into a list of ib which can then be dumped using
debugfs. Once dumped the ib is removed from the list. This
should allow to save & capute ib for further debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This already simplifies code significally and makes it maintaible
in case of adding memory reclocking plus voltage changing in future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
we need a constant sclk for i2c prescale. Also,
get the current sclk when calculating prescale rather
than using the default sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- only r4xx/r5xx/rs6xx/rs740 have clock gating atom table,
so disable it on r6xx. it's already disabled on r7xx
- check to make sure the clock_gating hook exists before
calling it. This avoids a segfault on asics without
that function.
- remove unused static power management function.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The idea is to flag a power state with a certain type and use
that type to decide on what state to select. On r6xx+, we
select a state and then transition between clock modes in that
state. On pre-r6xx, we transition between states directly.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The general idea is to validate the current hw state
against the set of power states and select a power
state based on that. This patch just pulls the power
states from the bios and prints the information. It
is not currently hooked up in the actual power management
code. Hooking it up will require reworking the the current
power state selection code and will be handled in a future
patch.
Additionally, we'd need to decide on some default lower
power states for cards without power tables.
v2 - increment state_index after checking for default state
v3 - fix typo in pm init on pre-atom cards, handle pre-atom
cards without x86 bioses
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
V2: reorganize functions, fix modesetting calls
V3: rebase patch, use radeon's workqueue
V4: enable on tested chipsets only, request VBLANK IRQs
V5: enable PM on older hardware (IRQs, mode_fixup, dpms)
V6: use separate dynpm module parameter
V7: drop RADEON_ prefix, set minimum mode for dpms off
V8: update legacy encoder call, fix order in rs600 IRQ
V9: update compute_clocks call in legacy, not only DPMS_OFF
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Set the number of crtcs in rdev at crtc init and use it
whenever we need the crtc count rather than recalculating
it everytime.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only flush the gpu caches before we submit a fence.
This leads to a small performance boost when we take
the extra gpu cache flushes out of the ddx and mesa.
Once this patch is in and the drm version is bumped,
we can remove the flushes from the ddx and drm.
Also, remove the extra cache flushes from the blit
routine.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is used in a lot of places in the atom encoder code.
While here fix the spelling of crtc_source_params.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The panel on the Toshiba A300-1BU laptop does not like the
PLL dividers selected by the avivo pll algo, but works fine
using the older method. Add a quirk to handle it.
Should fix fdo bug 26358.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Rework the pll algo selection so that the pll algo
in use can be selected more easily. This allows
us to select different pll divider selection algos
for specific monitors that work better with one algo
or the other. This is needed for the next patch which
adds an LVDS pll quirk for a specific notebook.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switch some magic numbers to their proper defines.
The register header madness needs to be cleaned up
at some point.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some servers hardcode an edid in rom so that they will
work properly with KVMs. This is a port of the relevant
code from the ddx.
[airlied: reworked to validate edid at boot stage - and
remove special quirk, if there is a valid EDID in the BIOS rom
we'll just try and use it.]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some servers have two VGA ports but only report
one in the bios connector tables. On these systems
always set up the TV DAC so that it displays properly
even if the bios is wrong.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
wire hw i2c support into radeon i2c algo.
fixes merged:
- handle bus probing correctly
- use meaningful error numbers
- abort if transaction fails
- The line mapping is different depending on the asic.
- protect hw i2c engine with a mutex
- rs300 doesn't have a pin select bit
- r200 has a different pin select setup
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is strange - like really really strange, twilight zone of strange.
VGA ports have DDC buses, but sometimes for some reasons the BIOS
says we don't and we oops - AMD mentioned bios bugs so we'll have
to add quirks.
reported on irc by nirbheek and
https://bugzilla.redhat.com/show_bug.cgi?id=554323
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ingo pointed out that we really don't give the user enough warning to make
a decision here. So revise the Kconfig text with a better warning.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: fix r300 vram width calculations
drm/radeon/kms: rs400/480 MC setup is different than r300.
drm/radeon/kms: make initial state of load detect property correct.
drm/radeon/kms: disable HDMI audio for now on rv710/rv730
drm/radeon/kms: don't call suspend path before cleaning up GPU
drivers/gpu/drm/radeon/radeon_combios.c: fix warning
ati_pcigart: fix printk format warning
drm/r100/kms: Emit cache flush to the end of command buffer. (v2)
drm/radeon/kms: fix regression rendering issue on R6XX/R7XX
drm/radeon/kms: move blit initialization after we disabled VGA
Some comments misspell "should" or "shouldn't"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Boot testing on my rs480 laptop found the MC idle never happened
on startup, a quick check with AMD found the idle bit is in a different
place on the rs4xx than r300.
Implement a new rs400 mc idle function to fix this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In suspend path we unmap the GART table while in cleaning up
path we will unbind buffer and thus try to write to unmapped
GART leading to oops. In order to avoid this we don't call the
suspend path in cleanup path. Cleanup path is clever enough
to desactive GPU like the suspend path is doing, thus this was
redondant.
Tested on: RV370, R420, RV515, RV570, RV610, RV770 (all PCIE)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/radeon_combios.c: In function 'radeon_combios_get_lvds_info':
drivers/gpu/drm/radeon/radeon_combios.c:893: warning: comparison is always false due to limited range of data type
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cache flush is required in case CPU is accessing rendered data.
This fixes glean/readPixSanity test case and random rendering
errors in sauerbraten and warzone2100.
v2 Fix comment ordering in r100_fence_ring_emit and remove extra
defines added in first version.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It seems that some R6XX/R7XX silently ignore HDP flush when
programmed through ring, this patch addback an ioctl callback
to allow R6XX/R7XX hw to perform such flush through MMIO in
order to fix a regression. For more details see:
http://bugzilla.kernel.org/show_bug.cgi?id=15186
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
VGA might be overwritting VRAM and corrupt our blit shader leading
to corruption, it likely won't happen if you load fbcon right after
radeon. Thanks to Shawn Starr and Andre Maasikas for tracking down
this issue.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some comments misspell "truly"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
