Machine constraints is configured during regulator register. If current
constraints are provided through machine constraints then it is observed
that sometime the current configured on rail is out of range what machine
constraint has.
Set the current constraints when setting machine constraints to make
sure that rail's current is within the range of given machine constraints.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet, voltage range for LDOs are as follows:
0000 = 0.9V
...(50mV steps)
01111 = 1.65V
10000 = 1.8V
... (100mV stepns)
11111 = 3.3V
So, there is no selector for 1.65V to 1.8V.
Correcting the range for max_uV for selector between 0 to 15.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The turn-on time of the regulator depends on the regulator device's
electrical characteristics. Sometimes regulator turn-on time also
depends on the capacitive load on the given platform and it can be
more than the datasheet value.
The driver provides the enable-time as per datasheet.
Add support for configure the enable ramp time through regulator
constraints so that regulator core can take this value for enable
time for that regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current equation on the comment is wrong.
For linear mapping starting from 0, the equation is (maxV-minV)/stepV + 1.
Since the linear mapping for PALMAS is not all starting from 0, the equation
on the comment is not useful and misleading. Thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ST Microelectronics STw481x PMIC used for the Nomadik
has one single software-controlled regulator for VMMC.
This driver registers directly to the compatible string
as there is just one regulator.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet (Referred TPS65913), the on-time for LDO is
500micro second. If LDO6 is in vibrator mode then the on-time
is 2000us.
Set the enable_time on regulator descriptor accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas rails like LDOs, SMPSs, REGENs, SYSENs can be enable and disable
by register programming through I2C communication as well as it can be
enable/disable with the external control input ENABLE1, ENABLE2 and NSLEEP.
Add support for configuring these rails to be controlled by external control
inputs. This is require to configure the rail's control register as well as
configuration of resource register.
Provide the external input names through parameter "roof-floor". Updated the
DT binding document to details different value of the roof-floor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No boards have used this functionality and the new default of providing
dummy regulators by default provides a better solution to the problem it
was trying to solve.
Signed-off-by: Mark Brown <broonie@linaro.org>
When a system has said that it has fully specified constraints for its
regulators it is still possible that some supplies may be missing,
especially if regulator support has been added to a driver after the
board was integrated. We can handle such situations more gracefully by
providing a dummy regulator.
Unless the caller has specifically indicated that the system design may
not include a given regulator by using regulator_get_optional() or that
it needs its interactions to have an effect using regulator_get_exclusive()
provide a dummy regulator if we can't locate a real one.
The kconfig option REGULATOR_DUMMY that provided similar behaviour for all
regulators has been removed, systems that need it should flag that they
have full constraints instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cut down on the size of core.c a bit more and ensure that the devres
versions of things don't do too much peering inside the internals of
the APIs they wrap.
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation of devm_regulator_get, devm_regulator_get_exclusive and
devm_regulator_get_optional are almost the same.
Introduce _devm_regulator_get helper function and refactor the code.
Also move devm_regulator_get_exclusive to proper place, put it after
regulator_get_exclusive() function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commmit af40a94aba "regulator: palmas: Use devm_regulator_register" missed
removing a regulator_unregister() call if palmas_extreg_init falis. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
NULL assignment corrupts the error pointer and is not
necessary.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
[Fixups from rebase onto v3.12 code -- broonie]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit e398b51a ("regulator: s2mps11: Convert to devm_regulator_register()")
intended to do this conversion. However the actual conversion to devm_* got
missed out. Fix this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulator drivers have a remove function that consists solely of
calling regulator_unregister() so provide a devm_regulator_register()
in order to allow this repeated code to be removed and help eliminate
error handling code.
Signed-off-by: Mark Brown <broonie@linaro.org>
With gcc 4.1.2:
drivers/regulator/da9063-regulator.c: In function ‘da9063_regulator_probe’:
drivers/regulator/da9063-regulator.c:847: warning: ‘da9063_reg_matches’ is used
uninitialized in this function
If the parent device already has platform data, da9063_reg_matches will
not be initialized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide the rail supply voltage through descriptor to the
core and remove the callbacks which implement the get_voltage
and list_voltage.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If given rail has the single voltage (n_voltages = 1) then provide the
rail voltage through regulator descriptor so that core can use this
value for finding voltage.
This will avoid the implementation of the callback for get_voltage() or
list_voltage() callback on regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If CONFIG_OF=n:
drivers/regulator/da9063-regulator.c: In function ‘da9063_parse_regulators_dt’:
drivers/regulator/da9063-regulator.c:712: warning: passing argument 1 of ‘PTR_ERR’ makes pointer from integer without a cast
drivers/regulator/da9063-regulator.c:712: warning: return makes pointer from integer without a cast
Use ERR_PTR() to encode an error code in a pointer.
PTR_ERR() is meant to decode an error code from a pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet (Referred TPS65913), the on-time for LDO is
500micro second. If LDO6 is in vibrator mode then the on-time
is 2000us.
Set the enable_time on regulator descriptor accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
With the following change
---------
commit ad02e84687
Author: Axel Lin <axel.lin@ingics.com>
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
----------
The list_voltage() takes the true value of selector which is
programmed in the register. As per smsp voltage table
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
121 1650000 (0.49V + 116 * 0.1) * RANGE
Hence making n_voltages for smps to 122.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
da9063_ldo_lim_event() is only referenced in this driver, make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
lp872x regulator driver can be built a module after commit 631a1fc
"regulator: build: Allow most regulators to be built as modules".
Make REGULATOR_LP872X depend on I2C to allow building lp872x module when I2C=m.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Below is the equation in original code:
tps65217_uv1_ranges:
0 ... 24: uV = vsel * 25000 + 900000;
25 ... 52: uV = (vsel - 24) * 50000 + 1500000;
= (vsel - 25) * 50000 + 1550000;
53 ... 55: uV = (vsel - 52) * 100000 + 2900000;
= (vsel - 53) * 100000 + 3000000;
56 ... 62: uV = 3300000;
tps65217_uv2_ranges:
0 ... 8: uV = vsel * 50000 + 1500000;
9 ... 13: uV = (vsel - 8) * 100000 + 1900000;
= (vsel - 9) * 100000 + 2000000;
14 ... 31: uV = (vsel - 13) * 50000 + 2400000;
= (vsel - 14) * 50000 + 2450000;
The voltage tables are composed of linear ranges.
This patch converts this driver to use multiple linear ranges APIs.
In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range
for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in
tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52.
This change makes it possible to reuse the same linear_ranges table for DCDCx.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_register() does not return NULL, it returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All the current limit tables have the values in ascend order.
So we can slightly optimize the for loop iteration because the first match
is the minimal value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver adds support for the following DA9063 PMIC regulators:
- 11x LDOs (named LDO1 - LDO11),
- 6x buck converters (BCORE1, BCORE2, BPRO, BMEM, BIO, BPERI),
Regulators provide following operations:
- REGULATOR_CHANGE_STATUS and REGULATOR_CHANGE_VOLTAGE for all regulators,
- REGULATOR_CHANGE_MODE for LDOs and buck converters, where:
- LDOs allow REGULATOR_MODE_NORMAL and REGULATOR_MODE_STANDBY,
- buck converters allow REGULATOR_MODE_FAST, REGULATOR_MODE_NORMAL
and REGULATOR_MODE_STANDBY,
- REGULATOR_CHANGE_CURRENT for buck converters (current limits).
The driver generates REGULATOR_EVENT_OVER_CURRENT for LDO3, LDO4, LDO7, LDO8
and LDO11.
Internally, PMIC provides two voltage configurations for normal and suspend
system state for each regulator. The driver switches between those on
suspend/wake-up to provide quick and fluent output voltage change.
This driver requires MFD core driver for operation.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is supposed to be testing "i < ARRAY_SIZE()" instead of just
"ARRAY_SIZE()".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The code to check whether num_regulator is valid is wrong because it should
iterate all array entries rather than break from the for loop if
pdata->regulators[i] is NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code has wrong mask and val arguments for updating ramp_delay. Fix it.
Also ensure the return value of get_ramp_delay() won't greater than 3 because
the mask field for ramp_val only takes 2 bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SMPS10 has two outputs OUT1 and OUT2 and have one input IN1.
SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either
in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures
it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be
used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using
regulator_enable().
[ axel.lin@ingics.com : Simplify regulator_desc setting for SMPS10_[OUT1|OUT2]
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move regulator_list_voltage_{linear,linear_range,table} helper functions to
helpers.c.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix a build warning for !CONFIG_OF and a cast from void* to
unsigned int which is invalid on 64bit machines.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I2C driver for the Dialog DA9210 Multi-phase 12A DC-DC Buck.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds devicetree bindings for max8660, along with some
documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
max_register should be register count - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No functional change, just makes the code shorter.
[Resolved conflict with platdata patch -- broonie]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce an enum and denote the device type via struct i2c_id's
driver_data field rather than comparing strings.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify the equation to calculate ramp_delay.
Below equations are equivalent:
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 50000 / (4 * ramp_delay);
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 12500 / ramp_delay;
So we don't need to read BIT6 of rdev->desc->vsel_reg for applying different
equations.
Also use rdev->desc->vsel_reg instead of run-time calculate register address.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the majority of supplies on devices are mandatory and can't be
physically omitted for electrical reasons some devices do have optional
supplies and need to know if they are missing, MMC being the most common
of these.
Currently the core accurately reports all errors when regulators are
requested since it does not know if the supply is one that must be provided
even if by a regulator software does not know about or if it is one that
may genuinely be disconnected. In order to allow this behaviour to be
changed and stub regulators to be provided in the former case add a new
regulator request function regulator_get_optional() which provides a hint
to the core that the regulator may genuinely not be connected.
Currently the implementation is identical to the current behaviour, future
patches will add support in the core for returning stub regulators in the
case where normal regulator_get() fails and the board has requested it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code adjust min_uV and uV_step but missed adjusting the n_voltages
setting.
When BIT6 is clear:
n_voltages = (1975000 - 400000) / 25000 + 1 = 64
When BIT6 is set:
n_voltages = (3300000 - 800000) / 50000 + 1 = 51
The n_voltages needs update because when BIT6 is set 0x73 ~ 0x7f are reserved.
When using regulator_list_voltage_linear, the n_voltages does matter here
because wrong n_voltages setting make the equation return wrong result.
e.g. if selector is 63, regulator_list_voltage_linear returns
800000 + (50000 * 63) = 4000000
It should return -EINVAL if the selector is in the range of 51 ~ 63.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All table based voltage list have ascendant order.
Use regulator_map_voltage_ascend for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since this is a i2c driver, use i2c_[set|get]_clientdata instead of
dev_[set|get]_drvdata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes below build errors:
CC [M] drivers/regulator/pfuze100-regulator.o
drivers/regulator/pfuze100-regulator.c:342:21: error: variable 'pfuze_regmap_config' has initializer but incomplete type
drivers/regulator/pfuze100-regulator.c:343:2: error: unknown field 'reg_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:343:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:343:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: error: unknown field 'val_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:344:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: error: unknown field 'max_register' specified in initializer
drivers/regulator/pfuze100-regulator.c:345:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: error: unknown field 'cache_type' specified in initializer
drivers/regulator/pfuze100-regulator.c:346:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c: In function 'pfuze100_regulator_probe':
drivers/regulator/pfuze100-regulator.c:370:2: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
drivers/regulator/pfuze100-regulator.c:370:21: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[2]: *** [drivers/regulator/pfuze100-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix building error on x86_64 and i386:
WARNING: modpost: missing MODULE_LICENSE() in
drivers/regulator/pfuze100-regulator.o
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The voltage table of da9034 LDO12 is:
1700000, 1750000, 1800000, 1850000, 1900000, 1950000, 2000000, 2050000
2700000, 2750000, 2800000, 2850000, 2900000, 2950000, 3000000, 3050000
The voltage table is composed of two linear ranges:
for selector 0 ... 7:
volt = 1700000 + 50000 * selector
for selector: 8 ... 15:
volt = 2700000 + 50000 * (selector - 8)
This patch converts da9034 LDO12 to use newly introduced helpers for multiple
linear ranges.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the regulator class code to use
the correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ldo voltage table is composed of linear ranges.
Below is the equation in original code (tps65912_vsel_to_uv_ldo):
0 ... 32: uv = vsel * 25000 + 800000;
33 ... 60: uv = (vsel - 32) * 50000 + 1600000;
= (vsel -33) * 50000 + 1650000;
61 ...63: uv = (vsel - 60) * 100000 + 3000000;
= (vsel - 61) * 100000 + 3100000;
This patch converts tps65912_ops_ldo to use multiple linear ranges APIs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SD, ALDO, and DLDO vlotage tables are composed of linear ranges.
This patch converts as3711 to use newly introduced helpers for multiple
linear ranges.
Below is the voltage table on datasheet:
SD:
00h: DC/DC powered down
01h-40h: Volt = 0.6V + sdx_vsel * 12.5mV
41h-70h: Volt = 1.4V + (sdx_vsel - 40h) * 25mV
71h-7Fh: Volt = 2.6V + (sdx_vsel - 70h) * 50mV
ALDO:
0h-0Fh: 1.2V + ldox_vsel * 50mV
10h-1Fh: 1.8V + (ldox_vsel - 10h) * 100mV
DLDO:
00h-10h: Volt = 0.9V + ldox_vsel * 50mV
11h-1fh: Do not use
20h-3fh: Volt = 1.75V + (ldox_vsel - 20h) * 50mV
Note, when convert to use linear ranges APIs, the equation for SD needs below
adjustment because the linear ranges APIs wiil substract range->min_sel when
apply the equation.
SD ( the equation to be used with linear ranges APIs )
01h-40h: Volt = 0.6125V + (sdx_vsel - 1h) * 12.5mV
41h-70h: Volt = 1.425V + (sdx_vsel - 41h) * 25mV
71h-7Fh: Volt = 2.650V + (sdx_vsel - 71h) * 50mV
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some regulator APIs are broken if n_voltages setting is not set.
e.g. regulator_count_voltages(), regulator_list_voltage(), and
regulator_can_change_voltage() do not work if n_voltages setting is missing.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver can be built as a module, make it depend on MFD_88PM800.
Otherwise, we are not able to select this driver when MFD_88PM800=m.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the regulator driver for PMIC 88pm800 including device tree
support.
88pm800 is an I2C-based power-management IC containing voltage
regulators, a real-time clock, and some general purpose ADC devices,
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code does not allow fixed voltage range in multiple linear ranges.
If someone does set range->uV_step == 0 in one of the linear ranges, we hit
divided by zero bug. This patch fixes this issue.
For fixed voltage range, return any selector means the same voltage.
Thus just return 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to use a normal per-CPU workqueue for delayed power downs
as they're not timing or performance critical and waking up a core for them
would defeat some of the point.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Since now we have ramp_delay and ramp_disable as standard regulator
constraints and DT part using it so this patch removes legacy part i.e. getting
ramp_delayxx and ramp_enable from pdata since it can be passed as
standard regulator constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds DT support for parsing regulators constraints for parent(mfd)
node and moves some common intialising code out of loop while registering.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Implementing set_ramp_rate() and using standard constraints for getting
ramp_delay and ramp_disable, instead of getting it as s2mps11 specific data
through platform data, makes driver more compliant with framework and reduces
the complexity for adding DT support.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently driver uses local struct s2mps11_info to store ramp rate for bucks
whic its getting through platform data, so instead of using regulator
constraints it should use s2mps11_info to calculate ramp delay.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In function _regulator_do_set_voltage(), old_selector gets intialised only
if (_regulator_is_enabled(rdev) && rdev->desc->ops->set_voltage_time_sel &&
rdev->desc->ops->get_voltage_sel)) is true.
Before calling set_voltage_time_sel() we checks if (old_selector >= 0) and it
will true if it got intialised properly. so we don't need to check again
_regulator_is_enabled(rdev) && rdev->desc->ops->set_voltage_time_sel before
calling set_voltage_time_sel().
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix a warning below.
drivers/regulator/lp872x.c:910:33: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
And checkpatch warnings are fixed.
WARNING: space prohibited before semicolon
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulators have several linear ranges of selector with different
step sizes, for example offering better resolution at lower voltages.
Provide regulator_{map,list}_voltage_linear_range() allowing these
regulators to use generic code. To do so a table of regulator_linear_range
structs needs to be pointed to from the descriptor.
This was inspired by similar code included in a driver submission from
Chao Xie and Yi Zhang at Marvell.
Signed-off-by: Mark Brown <broonie@linaro.org>
