Commit Graph

6511 Commits

Author SHA1 Message Date
Linus Torvalds
87367a0b71 Merge branch 'for-usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci
* 'for-usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
  Intel xhci: Limit number of active endpoints to 64.
  Intel xhci: Ignore spurious successful event.
  Intel xhci: Support EHCI/xHCI port switching.
  Intel xhci: Add PCI id for Panther Point xHCI host.
  xhci: STFU: Be quieter during URB submission and completion.
  xhci: STFU: Don't print event ring dequeue pointer.
  xhci: STFU: Remove function tracing.
  xhci: Don't submit commands when the host is dead.
  xhci: Clear stopped_td when Stop Endpoint command completes.
2011-05-28 12:36:15 -07:00
Sarah Sharp
2cf95c18d5 Intel xhci: Limit number of active endpoints to 64.
The Panther Point chipset has an xHCI host controller that has a limit to
the number of active endpoints it can handle.  Ideally, it would signal
that it can't handle anymore endpoints by returning a Resource Error for
the Configure Endpoint command, but they don't.  Instead it needs software
to keep track of the number of active endpoints, across configure endpoint
commands, reset device commands, disable slot commands, and address device
commands.

Add a new endpoint context counter, xhci_hcd->num_active_eps, and use it
to track the number of endpoints the xHC has active.  This gets a little
tricky, because commands to change the number of active endpoints can
fail.  This patch adds a new xHCI quirk for these Intel hosts, and the new
code should not have any effect on other xHCI host controllers.

Fail a new device allocation if we don't have room for the new default
control endpoint.  Use the endpoint ring pointers to determine what
endpoints were active before a Reset Device command or a Disable Slot
command, and drop those once the command completes.

Fail a configure endpoint command if it would add too many new endpoints.
We have to be a bit over zealous here, and only count the number of new
endpoints to be added, without subtracting the number of dropped
endpoints.  That's because a second configure endpoint command for a
different device could sneak in before we know if the first command is
completed.  If the first command dropped resources, the host controller
fails the command for some reason, and we're nearing the limit of
endpoints, we could end up oversubscribing the host.

To fix this race condition, when evaluating whether a configure endpoint
command will fix in our bandwidth budget, only add the new endpoints to
xhci->num_active_eps, and don't subtract the dropped endpoints.  Ignore
changed endpoints (ones that are dropped and then re-added), as that
shouldn't effect the host's endpoint resources.  When the configure
endpoint command completes, subtract off the dropped endpoints.

This may mean some configuration changes may temporarily fail, but it's
always better to under-subscribe than over-subscribe resources.

(Originally my plan had been to push the resource allocation down into the
ring allocation functions.  However, that would cause us to allocate
unnecessary resources when endpoints were changed, because the xHCI driver
allocates a new ring for the changed endpoint, and only deletes the old
ring once the Configure Endpoint command succeeds.  A further complication
would have been dealing with the per-device endpoint ring cache.)

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-27 12:08:14 -07:00
Sarah Sharp
ad808333d8 Intel xhci: Ignore spurious successful event.
The xHCI host controller in the Panther Point chipset sometimes produces
spurious events on the event ring.  If it receives a short packet, it
first puts a Transfer Event with a short transfer completion code on the
event ring.  Then it puts a Transfer Event with a successful completion
code on the ring for the same TD.  The xHCI driver correctly processes the
short transfer completion code, gives the URB back to the driver, and then
prints a warning in dmesg about the spurious event.  These warning
messages really fill up dmesg when an HD webcam is plugged into xHCI.

This spurious successful event behavior isn't technically disallowed by
the xHCI specification, so make the xHCI driver just ignore the spurious
completion event.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-27 12:08:13 -07:00
Sarah Sharp
69e848c209 Intel xhci: Support EHCI/xHCI port switching.
The Intel Panther Point chipsets contain an EHCI and xHCI host controller
that shares some number of skew-dependent ports.  These ports can be
switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX
that is controlled by registers in the xHCI PCI configuration space.  The
USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled
separately from the USB 2.0 data wires.

This switchover mechanism is there to support users who do a custom
install of certain non-Linux operating systems that don't have official
USB 3.0 support.  By default, the ports are under EHCI, SuperSpeed
terminations are off, and USB 3.0 devices will show up under the EHCI
controller at reduced speeds.  (This was more palatable for the marketing
folks than having completely dead USB 3.0 ports if no xHCI drivers are
available.)  Users should be able to turn on xHCI by default through a
BIOS option, but users are happiest when they don't have to change random
BIOS settings.

This patch introduces a driver method to switchover the ports from EHCI to
xHCI before the EHCI driver finishes PCI enumeration.  We want to switch
the ports over before the USB core has the chance to enumerate devices
under EHCI, or boot from USB mass storage will fail if the boot device
connects under EHCI first, and then gets disconnected when the port
switches over to xHCI.

Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI.  The
PCI quirks code will run before any other PCI probe function is called, so
this avoids the issue with boot devices.

Another issue is with BIOS behavior during system resume from hibernate.
If the BIOS doesn't support xHCI, it may switch the devices under EHCI to
allow use of the USB keyboard, mice, and mass storage devices.  It's
supposed to remember the value of the port routing registers and switch
them back when the OS attempts to take control of the xHCI host controller,
but we all know not to trust BIOS writers.

Make both the xHCI driver and the EHCI driver attempt to switchover the
ports in their PCI resume functions.  We can't guarantee which PCI device
will be resumed first, so this avoids any race conditions.  Writing a '1'
to an already set port switchover bit or a '0' to a cleared port switchover
bit should have no effect.

The xHCI PCI configuration registers will be documented in the EDS-level
chipset spec, which is not public yet.  I have permission from legal and
the Intel chipset group to release this patch early to allow good Linux
support at product launch.  I've tried to document the registers as much
as possible, so please let me know if anything is unclear.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-27 12:07:36 -07:00
Graeme Gregory
5ccee4ae8e USB: TWL6025 allow different regulator name
The twl6025 uses a different regulator for USB than the 6030 so select
the correct regulator name depending on the subclass of device.

Since V1

Use features passed via platform data instead of global variable.

Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-05-27 10:49:30 +01:00
Sarah Sharp
f444ff27e9 xhci: STFU: Be quieter during URB submission and completion.
Unsurprisingly, URBs get submitted and completed a lot in the xHCI
driver.  If we have to print 10 lines of debug for every URB submitted
or completed, then that can cause the whole system to stay in the
interrupt handler too long, and can cause Missed Service completion
codes for isochronous transfers.

Cut down the debugging in the URB submission and completion paths:
 - Don't squawk about successful transfers, only unsuccessful ones.
 - Only print the number of bytes transferred if this was a short
   transfer.
 - Don't print the endpoint index for successful transfers (will add
   more debug to failed transfers to show endpoint index there later).
 - Stop printing MMIO writes.  This debugging shows up when the endpoint
   doorbell is rung a to start a transfer (basically for every URB).
 - Don't print out the ring enqueue and dequeue pointers
 - Stop printing when we're pointing to a link TRB.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-25 16:03:14 -07:00
Sarah Sharp
5153b7b391 xhci: STFU: Don't print event ring dequeue pointer.
Stop printing out the event ring dequeue pointer and status register in
the operational register set.  The host will report an OK status 99% of
the time the interrupt handler is called, and usually when it's really
hosed, a host controller won't even call the interrupt handler.  So the
line is really useless.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-25 16:01:51 -07:00
Sarah Sharp
380032c3c8 xhci: STFU: Remove function tracing.
Remove unnecessary debugging from the xHCI driver.  We don't need to
know what function we're calling or returning from.  Now I know how to
use markup-oops.pl to de-mystify stack dumps of crashes.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-25 15:23:35 -07:00
Sarah Sharp
fe6c6c13d8 xhci: Don't submit commands when the host is dead.
When the xHCI host controller dies, the USB core may attempt to reset the
devices to their default configuration before disconnecting them.  This
causes calls into the xHCI bandwidth allocation functions.  Don't allow
those functions to submit commands or work on xHCI structures if the host
controller is marked as dying.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-25 15:23:35 -07:00
Sarah Sharp
0714a57c68 xhci: Clear stopped_td when Stop Endpoint command completes.
When an URB is cancelled, the xHCI driver issues a Stop Endpoint command
so that it can manipulate the ring and remove the transfer.  The xHC
hardware then places a transfer event with the completion code "Stopped"
or "Stopped Invalid" to let the driver know what TD it was in the middle
of processing.  This TD and TRB is stored in ep->stopped_td and
ep->stopped_trb.  These pointers are also used in handling stalled
endpoints.

By design, the Stop Endpoint command can race with URB completion.  By
the time the Stop Endpoint command is handled, the URBs to be cancelled
may have been given back to the driver.  Unfortunately, the stopped_td
and stopped_trb pointers were not getting cleared in this case.

The USB core unconditionally tries to reset the toggle bits on any
endpoints when a new alternate interface setting is installed.  When the
xHCI driver saw that ep->stopped_td was still set from the Stop Endpoint
command, xhci_reset_endpoint assumed the endpoint was actually stalled,
and attempted to clean up the endpoint rings.  This would manifest
itself in a failed Reset Endpoint command and failed Set TR dequeue
Pointer command after a successful Configure Endpoint command.  It may
have also been causing driver oops when the stopped_td was accessed.

This patch should be backported to stable kernels since 2.6.31.  Before
2.6.33, stopped_td was found in the xhci_endpoint_ring, not the
xhci_virt_ep.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2011-05-25 15:23:35 -07:00
Linus Torvalds
f50d1d9e8d Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia: Make struct pcmcia_device_id const, sound drivers edition
  staging: pcmcia: Convert pcmcia_device_id declarations to const
  pcmcia: Convert pcmcia_device_id declarations to const
  pcmcia: Make declaration and uses of struct pcmcia_device_id const
  pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
2011-05-24 13:28:35 -07:00
Linus Torvalds
c44dead70a Merge branch 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
  USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
  USB: UHCI: Support big endian GRUSBHC HC
  sparc: add {read,write}*_be routines
  USB: UHCI: Add support for big endian descriptors
  USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
  USB: UHCI: Add support for big endian mmio
  usb-storage: Correct adjust_quirks to include latest flags
  usb/isp1760: Fix possible unlink problems
  usb/isp1760: Move function isp1760_endpoint_disable() within file.
  USB: remove remaining usages of hcd->state from usbcore and fix regression
  usb: musb: ux500: add configuration and build options for ux500 dma
  usb: musb: ux500: add dma glue layer for ux500
  usb: musb: ux500: add dma name for ux500
  usb: musb: ux500: add ux500 specific code for gadget side
  usb: musb: fix compile error
  usb-storage: fix up the unusual_realtek device list
  USB: gadget: f_audio: Fix invalid dereference of initdata
  EHCI: don't rescan interrupt QHs needlessly
  OHCI: fix regression caused by nVidia shutdown workaround
  USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
  ...
2011-05-23 12:33:02 -07:00
Linus Torvalds
57d19e80f4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  b43: fix comment typo reqest -> request
  Haavard Skinnemoen has left Atmel
  cris: typo in mach-fs Makefile
  Kconfig: fix copy/paste-ism for dell-wmi-aio driver
  doc: timers-howto: fix a typo ("unsgined")
  perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
  md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
  treewide: fix a few typos in comments
  regulator: change debug statement be consistent with the style of the rest
  Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
  audit: acquire creds selectively to reduce atomic op overhead
  rtlwifi: don't touch with treewide double semicolon removal
  treewide: cleanup continuations and remove logging message whitespace
  ath9k_hw: don't touch with treewide double semicolon removal
  include/linux/leds-regulator.h: fix syntax in example code
  tty: fix typo in descripton of tty_termios_encode_baud_rate
  xtensa: remove obsolete BKL kernel option from defconfig
  m68k: fix comment typo 'occcured'
  arch:Kconfig.locks Remove unused config option.
  treewide: remove extra semicolons
  ...
2011-05-23 09:12:26 -07:00
Linus Torvalds
ad9471752e Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (110 commits)
  [SCSI] qla2xxx: Refactor call to qla2xxx_read_sfp for thermal temperature.
  [SCSI] qla2xxx: Unify the read/write sfp mailbox command routines.
  [SCSI] qla2xxx: Clear complete initialization control block.
  [SCSI] qla2xxx: Allow an override of the registered maximum LUN.
  [SCSI] qla2xxx: Add host number in reset and quiescent message logs.
  [SCSI] qla2xxx: Correctly read sfp single byte mailbox register.
  [SCSI] qla2xxx: Add qla82xx_rom_unlock() function.
  [SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.
  [SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function
  [SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.
  [SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.
  [SCSI] qla2xxx: Fix hang during driver unload when vport is active.
  [SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.
  [SCSI] qla2xxx: Fix virtual port failing to login after chip reset.
  [SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.
  [SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)
  [SCSI] ipr: Rate limit DMA mapping errors
  [SCSI] hpsa: add P2000 to list of shared SAS devices
  [SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.
  [SCSI] hpsa: remove superfluous sleeps around reset code
  ...
2011-05-20 13:29:52 -07:00
Linus Torvalds
268bb0ce3e sanitize <linux/prefetch.h> usage
Commit e66eed651f ("list: remove prefetching from regular list
iterators") removed the include of prefetch.h from list.h, which
uncovered several cases that had apparently relied on that rather
obscure header file dependency.

So this fixes things up a bit, using

   grep -L linux/prefetch.h $(git grep -l '[^a-z_]prefetchw*(' -- '*.[ch]')
   grep -L 'prefetchw*(' $(git grep -l 'linux/prefetch.h' -- '*.[ch]')

to guide us in finding files that either need <linux/prefetch.h>
inclusion, or have it despite not needing it.

There are more of them around (mostly network drivers), but this gets
many core ones.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-05-20 12:50:29 -07:00
Jan Andersson
d5f6db9e1a USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
{read,write}l_be are now defined for SPARC and do not need to be
defined for SPARC_LEON in ehci.h. This patch fixes the following
warnings:

  CC      drivers/usb/host/ehci-hcd.o
In file included from drivers/usb/host/ehci-hcd.c:119:
drivers/usb/host/ehci.h:631:1: warning: "readl_be" redefined
...
drivers/usb/host/ehci-hcd.c:119:
drivers/usb/host/ehci.h:632:1: warning: "writel_be" redefined
...

Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:49:52 -07:00
Jan Andersson
fda928ac97 USB: UHCI: Support big endian GRUSBHC HC
This patch adds support for big endian GRUSBHC UHCI controllers.
The HCD bus glue will probe the register interface to determine
the endianness of the controller.

Tested on GR-LEON4-ITX board which has a controller with little endian
interface and on custom LEON3 board with a BE controller.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:45:32 -07:00
Jan Andersson
51e2f62fe7 USB: UHCI: Add support for big endian descriptors
This patch adds support for universal host controllers that use
big endian descriptors. Support for BE descriptors requires a non-PCI
host controller. For kernels with PCI-only UHCI there should be no
change in behaviour.

This patch tries to replicate the technique used to support BE descriptors
in the EHCI HCD. Parts added to uhci-hcd.h are basically copy'n'paste from
ehci.h.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:43:20 -07:00
Alan Stern
bab1ff1bda USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
This patch (as1462) updates the special accessor functions defined in
uhci-hcd.h.  Rather than using a full compiler barrier, all we really
need is the ACCESS_ONCE() mechanism, because the idea is to force the
compiler to store a fixed copy of a possibly changing value.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:43:19 -07:00
Jan Andersson
8452c6745e USB: UHCI: Add support for big endian mmio
This patch adds support for big endian mmio to the UHCI HCD. Big endian
mmio is supported by adding a flag bit to the UHCI HCD replicating the
solution used in the EHCI HCD.

When adding big endian support this patch also adds a check to see if we
need to support HCs with PCI I/O registers when we support HCs with MMIO.

This patch also adds 'const' to the register access functions' uhci_hcd
argument.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:43:19 -07:00
Karl Relton
5116901d85 usb-storage: Correct adjust_quirks to include latest flags
Commits ae38c78a03
and 00914025cc added quirk flags
US_FL_NO_READ_DISC_INFO and US_FL_NO_READ_CAPACITY_16 to
the usb-storage driver. However they did not add the corresponding flags
to adjust_quirks() in usb.c, so there was no facility for a user
to over-ride/add them via the quirks module parameter.

Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:34:05 -07:00
Arvid Brodin
d05b6ec01b usb/isp1760: Fix possible unlink problems
Use skip map to avoid spurious interrupts from unlinked transfers.
Also changes to urb_dequeue() and endpoint_disable() to avoid
release of spinlock in uncertain state.

Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:34:04 -07:00
Arvid Brodin
079cdb0947 usb/isp1760: Move function isp1760_endpoint_disable() within file.
Preparation for patch . The function isp1760_endpoint_disable() does almost
the same thing as urb_dequeue(). In patch  I change these to use a common
helper function instead of calling each other - for clarity but also to
avoid releasing the spinlock while in a "questionable" state. It seemed
proper to have these functions close to each other in the code.

Signed-off-by: Arvid Brodin <arvid.brodin@enea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:34:04 -07:00
Alan Stern
69fff59de4 USB: remove remaining usages of hcd->state from usbcore and fix regression
This patch (as1467) removes the last usages of hcd->state from
usbcore.  We no longer check to see if an interrupt handler finds that
a controller has died; instead we rely on host controller drivers to
make an explicit call to usb_hc_died().

This fixes a regression introduced by commit
9b37596a2e (USB: move usbcore away from
hcd->state).  It used to be that when a controller shared an IRQ with
another device and an interrupt arrived while hcd->state was set to
HC_STATE_HALT, the interrupt handler would be skipped.  The commit
removed that test; as a result the current code doesn't skip calling
the handler and ends up believing the controller has died, even though
it's only temporarily stopped.  The solution is to ignore HC_STATE_HALT
following the handler's return.

As a consequence of this change, several of the host controller
drivers need to be modified.  They can no longer implicitly rely on
usbcore realizing that a controller has died because of hcd->state.
The patch adds calls to usb_hc_died() in the appropriate places.

The patch also changes a few of the interrupt handlers.  They don't
expect to be called when hcd->state is equal to HC_STATE_HALT, even if
the controller is still alive.  Early returns were added to avoid any
confusion.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Manuel Lauss <manuel.lauss@googlemail.com>
CC: Rodolfo Giometti <giometti@linux.it>
CC: Olav Kongas <ok@artecdesign.ee>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-19 16:34:04 -07:00
Jean Delvare
e05503ef11 Haavard Skinnemoen has left Atmel
Haavard's e-mail address at Atmel is no longer valid.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-05-18 23:24:50 +02:00
Grant Likely
b1608d69cb drivercore: revert addition of of_match to struct device
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time.  This was unsafe
because matching is not an atomic operation with probing a driver.  If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.

This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-05-18 12:32:23 -06:00
Mian Yousaf Kaukab
d23894402b usb: musb: ux500: add configuration and build options for ux500 dma
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-05-18 14:43:16 +03:00
Mian Yousaf Kaukab
8dcc8f72e3 usb: musb: ux500: add dma glue layer for ux500
Unaligned sizes and buffers are not supported and they will be filtered
out by is_compatible().

Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-05-18 14:43:15 +03:00
Mian Yousaf Kaukab
e3c496f9b3 usb: musb: ux500: add dma name for ux500
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-05-18 14:43:14 +03:00
Mian Yousaf Kaukab
a48ff90678 usb: musb: ux500: add ux500 specific code for gadget side
Although U8500 and U5500 platforms use paltform dma, Inventra dma specific code
can work for them for the most part. Only difference is for the Rx path where
this patch is making use of request->short_not_ok to select dma mode.

Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-05-18 14:43:13 +03:00
Felipe Balbi
28e4970555 usb: musb: fix compile error
commit 35a83365da6aa10095c6138cc428c15853409c32
(usb: musb: drop unneeded musb_debug trickery)
introduced a compile error for blackfin and
tusb6010 glue layers. Fix it.

Reported-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-05-18 14:43:12 +03:00
Alan Stern
a8e62dd6d9 usb-storage: fix up the unusual_realtek device list
This patch (as1461) fixes the unusual_devs entries for the Realtek USB
card reader.  They should be ordered by PID, and they should not
override the Subclass and Protocol values provided by the device.
Otherwise a notification about unnecessary entries gets printed in the
kernel log during probing.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-By: Tony Vroon <tony@linx.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:56:28 -07:00
Martin Jackson
e6251a9217 USB: gadget: f_audio: Fix invalid dereference of initdata
as_out_ep_desc contines to be used during gadget enumeration and thus
should not be marked as __initdata

Signed-off-by: Martin Jackson <mjackson220.list@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:20:24 -07:00
Alan Stern
1e12c910ee EHCI: don't rescan interrupt QHs needlessly
This patch (as1466) speeds up processing of ehci-hcd's periodic list.
The existing code will pointlessly rescan an interrupt endpoint queue
each time it encounters the queue's QH in the periodic list, which can
happen quite a few times if the endpoint's period is low.  On some
embedded systems, this useless overhead can waste so much time that
the driver falls hopelessly behind and loses events.

The patch introduces a "periodic_stamp" variable, which gets
incremented each time scan_periodic() runs and each time the scan
advances to a new frame.  If the corresponding stamp in an interrupt
QH is equal to the current periodic_stamp, we assume the QH has
already been scanned and skip over it.  Otherwise we scan the QH as
usual, and if none of its URBs have completed then we store the
current periodic_stamp in the QH's stamp, preventing it from being
scanned again.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:20:24 -07:00
Alan Stern
2b7aaf503d OHCI: fix regression caused by nVidia shutdown workaround
This patch (as1463) fixes a regression caused by commit
3df7169e73 (OHCI: work around for nVidia
shutdown problem).

The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down.  For
example, the LED on an optical mouse would remain on, draining a
laptop's battery.  The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown.  The workaround was to put the
controllers into the Suspend state instead.

It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately.  Thus, working around the original bug
on some machines exposes other bugs on other machines.

The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID.  I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess.  So far it was worked out okay for all the people who have
tested it.

This fixes Bugzilla .

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: Yury Siamashka <yurand2@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:20:23 -07:00
Mark Brown
e99c4309fb USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
If for some reason we fail to set the voltage range for the VDDCX regulator
when removing it's better to still disable and free the regulator as that
avoids leaking a reference to it and is likely to ensure that it's turned
off completely.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:20:23 -07:00
Mark Brown
7b521fcb6b USB: OTG: msm: Allow the widest possible range for VDDCX when removing
When not active the hardware should be able to tolerate voltages within
the normal operating range so when removing set the maximum voltage we
can use to the maximum rather than minimum of the operating range. This
will improve interoperability in case we end up sharing the supply in
some design.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:20:23 -07:00
Marcin Gałczyński
610ba42f29 USB: option: add support for Huawei E353 device
I am sharing patch to the devices/usb/serial/option.c. This allows
operation of Huawei E353 broadband modem using the “option” driver. The
patch simply adds new constant with proper product ID and an entry to
usb_device_id. I worked on the 2.6.38.6 sources. Tested on Dell inspiron
1764 (i3 core cpu) and brand new Huawei E353 modem, Fedora 15 beta.

Looking at the type of change, i doubt it has potential to introduce
problems in other parts of kernel or the driver itself.

Signed-off-by: Marcin Galczynski <marcin@galczynski.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-17 11:20:22 -07:00
Sarah Sharp
834cb0fc47 xhci: Fix memory leak bug when dropping endpoints
When the USB core wants to change to an alternate interface setting that
doesn't include an active endpoint, or de-configuring the device, the xHCI
driver needs to issue a Configure Endpoint command to tell the host to
drop some endpoints from the schedule.  After the command completes, the
xHCI driver needs to free rings for any endpoints that were dropped.

Unfortunately, the xHCI driver wasn't actually freeing the endpoint rings
for dropped endpoints.  The rings would be freed if the endpoint's
information was simply changed (and a new ring was installed), but dropped
endpoints never had their rings freed.  This caused errors when the ring
segment DMA pool was freed when the xHCI driver was unloaded:

[ 5582.883995] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff88003371d000 busy
[ 5582.884002] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033716000 busy
[ 5582.884011] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033455000 busy
[ 5582.884018] xhci_hcd 0000:06:00.0: Freed segment pool
[ 5582.884026] xhci_hcd 0000:06:00.0: Freed device context pool
[ 5582.884033] xhci_hcd 0000:06:00.0: Freed small stream array pool
[ 5582.884038] xhci_hcd 0000:06:00.0: Freed medium stream array pool
[ 5582.884048] xhci_hcd 0000:06:00.0: xhci_stop completed - status = 1
[ 5582.884061] xhci_hcd 0000:06:00.0: USB bus 3 deregistered
[ 5582.884193] xhci_hcd 0000:06:00.0: PCI INT A disabled

Fix this issue and free endpoint rings when their endpoints are
successfully dropped.

This patch should be backported to kernels as old as 2.6.31.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
2011-05-16 17:59:22 -07:00
Sarah Sharp
30f89ca021 xhci: Fix memory leak in ring cache deallocation.
When an endpoint ring is freed, it is either cached in a per-device ring
cache, or simply freed if the ring cache is full.  If the ring was added
to the cache, then virt_dev->num_rings_cached is incremented.  The cache
is designed to hold up to 31 endpoint rings, in array indexes 0 to 30.
When the device is freed (when the slot was disabled),
xhci_free_virt_device() is called, it would free the cached rings in
array indexes 0 to virt_dev->num_rings_cached.

Unfortunately, the original code in xhci_free_or_cache_endpoint_ring()
would put the first entry into the ring cache in array index 1, instead of
array index 0.  This was caused by the second assignment to rings_cached:

	rings_cached = virt_dev->num_rings_cached;
	if (rings_cached < XHCI_MAX_RINGS_CACHED) {
		virt_dev->num_rings_cached++;
		rings_cached = virt_dev->num_rings_cached;
		virt_dev->ring_cache[rings_cached] =
			virt_dev->eps[ep_index].ring;

This meant that when the device was freed, cached rings with indexes 0 to
N would be freed, and the last cached ring in index N+1 would not be
freed.  When the driver was unloaded, this caused interesting messages
like:

xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880063040000 busy

This should be queued to stable kernels back to 2.6.33.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
2011-05-16 17:59:11 -07:00
Sarah Sharp
b513d44751 xhci: Fix full speed bInterval encoding.
Dmitry's patch

dfa49c4ad1 USB: xhci - fix math in xhci_get_endpoint_interval()

introduced a bug.  The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)).  Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.

Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding.  The isochronous endpoint encoding was the same.

This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:

[  100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[  100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[  100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[  100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000

When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 16:34:06 -07:00
Greg Kroah-Hartman
2efeaeb00f Merge branch 'for-next' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb into usb-next
* 'for-next' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb:
  MAINTAINERS: tree moved to kernel.org
  usb: musb: Calling VBUS pulsing API when SRP is initiated.
  usb: otg: TWL6030: OMAP4430: Adding SRP VBUS pulsing API
  usb: musb: host: remove duplicate check in musb_ep_program()
  usb: musb: export musb_interrupt symbol
  usb: musb: allow musb and glue layers to be modules
  usb: musb: drop unneeded musb_debug trickery
2011-05-13 16:04:02 -07:00
Felipe Balbi
472b91274a usb: gadget: rndis: don't test against req->length
composite.c always sets req->length to zero
and expects function driver's setup handlers
to return the amount of bytes to be used
on req->length. If we test against req->length
w_length will always be greater than req->length
thus making us always stall that particular
SEND_ENCAPSULATED_COMMAND request.

Tested against a Windows XP SP3.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:09 -07:00
Jean-Christophe PLAGNIOL-VILLARD
bf1f0a05d4 usb/gadget: at91sam9g20 fix end point max packet size
on 9g20 they are the same as the 9260

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:08 -07:00
Julia Lawall
b0795bbf6d drivers/usb/serial/opticon.c: Release resources on kmalloc failure
Several resources have been allocated before this kmalloc failure, and thus
they should be released in this error handling code, as done in nearby
error handling code.

The semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
local idexpression urb;
statement S;
position p1,p2;
@@

urb = usb_alloc_urb@p1(...);
... when != urb
if (urb == NULL) S
... when != urb
(
return <+...urb...+>;
|
return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

cocci.print_main("",p1)
cocci.print_secs("",p2)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:08 -07:00
Jingoo Han
2328ceaea4 USB: s3c-hsotg: return proper error if clk_get fails
Return PTR_ERR(hsotg->clk) instead of -EINVAL if clk_get fails

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:07 -07:00
Jingoo Han
66e5c64348 USB: s3c-hsotg: fix checkpatch warnings
This patch fixes the checkpatch warnings listed below:

WARNING: braces {} are not necessary for any arm of this statement
WARNING: please, no space before tabs

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:07 -07:00
Jingoo Han
d6167660b2 USB: s3c-hsudc: fix checkpatch error and warning
This patch fixes the checkpatch error and warning listed below:

ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:06 -07:00
Jingoo Han
004c127ef0 USB: s3c-hsudc: use IS_ERR() instead of NULL check
clk_get() returns ERR_PTR() on error, not NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-13 15:51:06 -07:00
Hema HK
8620543eda usb: musb: Calling VBUS pulsing API when SRP is initiated.
Call VBUS pulsing API when there is SRP initiation from user space.

Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2011-05-13 14:43:56 +03:00