Add a spinlock and a 'enabled' boolean on channel descriptor, to avoid
using buffer descriptors in the interrupt context,
when sdma_disable_channel is called meanwhile.
Signed-off-by: Thierry Bultel <tbultel@pixelsurmer.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This avoid the following error when using an initramfs on wandboard quad
Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver already supports DMA_DEV_TO_DEV in sdma_config(),
DMA_SLAVE_BUSWIDTH_2_BYTES and DMA_SLAVE_BUSWIDTH_1_BYTE in
sdma_prep_slave_sg(). So this patch adds them to the lists.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace '%d' by '%zu' to fix the following compilation warning:-
drivers/dma/imx-sdma.c: In function ‘sdma_prep_dma_cyclic’:
drivers/dma/imx-sdma.c:1327:5: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat=]
channel, period_len, 0xffff);
^
drivers/dma/imx-sdma.c:1350:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 5 has type ‘size_t’ [-Wformat=]
dev_dbg(sdma->dev, "entry %d: count: %d dma: %#llx %s%s\n",
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
sdma_disable_channel() cannot ensure dma is stopped to access
module's FIFOs. There is chance SDMA core is running and accessing
BD when disable of corresponding channel, this may cause sometimes
even after call of .sdma_disable_channel(), SDMA core still be
running and accessing module's FIFOs.
According to NXP R&D team a delay of one BD SDMA cost time (maximum
is 1ms) should be added after disable of the channel bit, to ensure
SDMA core has really been stopped after SDMA clients call
.device_terminate_all.
This patch introduces adds a new function sdma_disable_channel_with_delay()
which simply adds 1ms delay after call sdma_disable_channel(),
and set it as .device_terminate_all.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The SDMA hardware/driver does not actually report the transfer residue at
burst size granularity, but in fact is only able to report residue after
each finished segment.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The residue calculation was taking in consideration that dma
transaction status will be always retrieved in the dma callback
used to inform that dma transfer is complete. However this is not
the case for all subsystems that use dma. Some subsystems use a
timer to check the dma status periodically.
Therefore the calculation was updated and residue is calculated
accordingly by a) update the residue calculation taking in
consideration the last used buffer index by using *buf_ptail* variable
and b) chn_real_count (number of bytes transferred) is initialized to
zero, when dma channel is created, to avoid using an uninitialized
value in residue calculation when dma status is checked without
waiting dma complete event.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of dmaenegine to
register a callback_result which tells them the result of the dma
transaction. Right now only one user ntb is using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no place in
kernel, this also remove NO_IRQ from dmaengine subsystem (both arm and
ppc users)
- Support for IOMMU slave transfers and it implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of driver,
and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9iA3
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of
dmaenegine to register a callback_result which tells them the
result of the dma transaction. Right now only one user (ntb) is
using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no
place in kernel, this also remove NO_IRQ from dmaengine subsystem
(both arm and ppc users)
- Support for IOMMU slave transfers and its implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of
driver, and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers"
* tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (169 commits)
async_pq_val: fix DMA memory leak
dmaengine: virt-dma: move function declarations
dmaengine: omap-dma: Enable burst and data pack for SG
DT: dmaengine: rcar-dmac: document R8A7743/5 support
dmaengine: fsldma: Unmap region obtained by of_iomap
dmaengine: jz4780: fix resource leaks on error exit return
dma-debug: fix ia64 build, use PHYS_PFN
dmaengine: coh901318: fix integer overflow when shifting more than 32 places
dmaengine: edma: avoid uninitialized variable use
dma-mapping: fix m32r build warning
dma-mapping: fix ia64 build, use PHYS_PFN
dmaengine: ti-dma-crossbar: enable COMPILE_TEST
dmaengine: omap-dma: enable COMPILE_TEST
dmaengine: edma: enable COMPILE_TEST
dmaengine: ti-dma-crossbar: Fix of_device_id data parameter usage
dmaengine: ti-dma-crossbar: Correct type for of_find_property() third parameter
dmaengine/ARM: omap-dma: Fix the DMAengine compile test on non OMAP configs
dmaengine: edma: Rename set_bits and remove unused clear_bits helper
dmaengine: edma: Use correct type for of_find_property() third parameter
dmaengine: edma: Fix of_device_id data parameter usage (legacy vs TPCC)
...
The calculation of the DMA transaction residue supports only fixed
size data transfers. This implementation is not covering all
operations (e.g. data receiving) when we need to know the exact amount
of bytes transferred.
The loop channels handling was changed to clear the buffer
descriptor errors and use the bd->mode.count to calculate the
residue.
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having the SDMA driver use a tasklet for running the clients
callback introduce some issues:
- probability to have desynchronized data because of the
race condition created since the DMA transaction status
is retrieved only when the callback is executed, leaving
plenty of time for transaction status to get altered.
- inter-transfer latency which can leave channels idle.
Move the callback execution, for cyclic channels, to SDMA
interrupt (as advised in `Documentation/dmaengine/provider.txt`)
to (a)reduce the inter-transfer latency and (b) eliminate the
race condition possibility where DMA transaction status might
be changed by the time is read.
The responsibility of the SDMA interrupt latency
is moved to the SDMA clients which case by case should defer
the work to bottom-halves when needed.
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow i.MX7 to work with the imx-sdma driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is in preperation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
David reported:
[drivers/dma/imx-sdma.c:769]: (style) Variable 'emi_2_emi' is assigned a value that is never used
Since emi_2_emi is never used afterwards, remove thsi as well
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
David reported:
drivers/dma/imx-sdma.c:1003]: (style) Same expression on both sides of '|='
ORing with itself yields same result, So remove this
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine device should explicitly call devm_free_irq() when using
devm_request_irq().
The irq is still ON when devices remove is executed and irq should be
quiesced before remove is completed.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Currently the handler ignores the channel 0 interrupt and thus doesn't ack
it properly. This is done in order to allow sdma_run_channel0() to poll
on the irq status bit, as this function may be called in atomic context,
but needs to know when the channel has finished.
This works mostly, as the polling happens under a spinlock, disabling IRQs
on the local CPU, leaving only a very slight race window for a spurious
IRQ to happen if the handler is executed on another CPU in an SMP system.
Still this is clearly suboptimal.
This behavior turns into a real problem on an RT system, where the spinlock
doesn't disable IRQs on the local CPU. Not acking the IRQ in the handler
in such a setup is very likely to drown the CPU in an IRQ storm, leaving
it unable to make any progress in the polling loop, leading to the IRQ
never being acked.
Fix this by properly acknowledging the channel 0 IRQ in the handler.
As the IRQ status bit can no longer be used to poll for the channel
completion, switch over to using the SDMA_H_STATSTOP register for this
purpose, where bit 0 is cleared by the hardware when the channel is done.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sdma_probe function will call sdma_event_remap, but sdma_event_remap
marked with the __init annotation which make the kbuild complains as the
following log:
WARNING: drivers/dma/built-in.o(.text+0x56fc): Section mismatch in reference
from the function sdma_probe() to the function .init.text:sdma_event_remap()
The function sdma_probe() references
the function __init sdma_event_remap().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_event_remap is wrong.
Remove the __init annotation on sdma_event_remap to kill this build warning
Signed-off-by: Jason Liu <r64343@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to print that the driver has been initialized
or removed, so remove such messages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit d078cd1b41 ("dmaengine: imx-sdma: Add imx6sx platform
support") we get this message on every boot on mx6q:
imx-sdma 20ec000.sdma: no event needs to be remapped
, which is not very helpful.
Move the message to debug level instead.
Cc: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_enable() may fail, so we should better check the return value and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new Solo X has more requirements for SDMA events. So it creates
a event mux to remap most of event numbers in GPR (General Purpose
Register). If we want to use SDMA support for those module who do
not get the even number as default, we need to configure GPR first.
Thus this patch adds this support of GPR event remapping configuration
to the SDMA driver.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DEV_TO_DEV support for i.MX SDMA driver to support data
transfer between two peripheral FIFOs.
The per_2_per script requires two peripheral addresses and two DMA
requests, and it need to check the src addr and dst addr is in the SPBA
bus space or in the AIPS bus space.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently when version 3.1 of the mx6q SDMA firmware is used we get:
[ 0.392169] imx-sdma 20ec000.sdma: unknown firmware version
[ 0.399281] imx-sdma 20ec000.sdma: initialized
Add support for it.
Based on a patch from Shengjiu Wang from the internal FSL kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Below comments got from Page4724 of Reference Manual of i.mx6q:
http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf
--"Static context mode should be used for the first channel called
after reset to ensure that the all context RAM for that channel is
initialized during the context SAVE phase when the channel is
done or yields. Subsequent calls to the same channel or
different channels may use any of the dynamic context modes.
This will ensure that all context locations for the bootload
channel are initialized, and prevent undefined values in context
RAM from being loaded during the context restore if the
channel is re-started later"
Unfortunately, the rule was broken by commit(5b28aa319b)
.This patch just take them back.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to return a 'fake' value upon platform_get_irq() failure.
Just propagate the real error instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
By using devm functions we can make the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since ecc19d1786 ("dmaengine: Add a warning for drivers not using the
generic slave caps retrieval") the following warning is observed:
[ 0.224981] ------------[ cut here ]------------
[ 0.225013] WARNING: CPU: 0 PID: 1 at drivers/dma/dmaengine.c:830 dma_async_device_register+0x2a0/0x4c8()
[ 0.225023] this driver doesn't support generic slave capabilities reporting
Declare the slave capabilities to avoid such warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Split the device_control callback of the Freescale IMX SDMA driver to make use
of the newly introduced callbacks, that will eventually be used to retrieve
slave capabilities.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fixed a coding style error, switch and case should be at the same indent
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a firmware cannot be found for the SDMA engine then we can
continue with the internal ROM firmware.
The meaning of this message is frequently asked for, so make clear
that the driver still works with the internal ROM firmware and reduce
the loglevel from err to info.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch simply adds a new DMATYPE for SAI which's included
in i.MX6 Solo X.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When platform_driver_probe() is not used, sdma_probe() can be called
by bind/unbind via sysfs. In addition, sdma_init() can be called by
sdma_probe(). Thus, __init annotation should be removed from sdma_init(),
Also, this patch fixes section mismatch warning.
WARNING: drivers/dma/built-in.o(.text+0xd6e4): Section mismatch in reference from the function sdma_probe() to the function
.init.text:sdma_init()
The function sdma_probe() references
the function __init sdma_init().
This is often because sdma_probe lacks a __init
annotation or the annotation of sdma_init is wrong.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In e34b731faa ("dma: imx-sdma: Remove spurious __init annotation on
sdma_probe()"), Mark found an extraneous __init label and fixed it.
However, he missed another one, because now we get this other warning:
WARNING: drivers/dma/imx-sdma.o(.text+0x3bb4): Section mismatch in reference from the function sdma_probe() to the function .init.text:sdma_get_firmware()
The function sdma_probe() references
the function __init sdma_get_firmware().
Same reasoning as the last time, the function may get called at
runtime, so it can't be __init.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We can't annotate probe functions as __init since binding can occur at
any time, not just during kernel init.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several dma drivers calls tasklet_kill() in remove function. This is done
because all running tasklets should be killed on remove. This is missing
in imx sdma driver, so adding tasklet_kill() in sdma_remove function.
Signed-off-by: Vignesh Raman <Vignesh_Raman@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently there is no module_exit declared in SDMA driver, so that once
sdma module is inserted, it's shown with permanent attribute by lsmod,
and it can't be removed.
Use module_platform_driver to register/unregister SDMA driver and modify
SDMA's remove operation, to make SDMA driver possible to be removed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The argument is always set to NULL and never used. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Shared Peripheral ASRC, running on SPBA, needs to use shp sciprts for
DMA transfer. So this patch just adds a new DMATYPE for it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The filter() function is currently called by xlate() while it transfers
imx_dma_data as a local variable to the filter() but releases the data
right after returning a DMA channel pointer, which results chan->private
pointing an invalid memory space.
So this patch just stores the imx_dma_data into sdmac to make usre the
private pointer valid as long as the channel exists.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
I received a report this morning from one of the Novena developers that
the behaviour of the iMX6 ASoC codec driver (using imx-pcm-dma.c) was
sub-optimal under high system load.
While there are issues relating to system load remaining, upon reviewing
the ASoC imx-pcm-dma.c driver, it was noticed that it not using the
residue support, because SDMA doesn't support it. This has the effect
that SDMA has to make multiple calls into the ASoC and ALSA code, one
for each period.
Since ALSA's snd_pcm_elapsed() does not need to be called multiple times
and it is entirely sufficient to call it once to update ALSA with the
current buffer position via the pointer method, we can do better here.
We can also avoid stopping the DMA entirely, just like real cyclic DMA
implementations behave. While this means that we replay some old samples,
this is a nicer behaviour than having audio stop and restart.
The changes to achieve this are relatively minor - imx-sdma.c can track
where the DMA is to the nearest descriptor boundary - it does this
already when deciding how many callbacks to issue. In doing this,
buf_tail always points at the descriptor which will complete next.
The residue is defined by the bytes remaining to the end of the buffer,
when the buffer is viewed as a single block of memory [start...end].
So, when we start out, there's a full buffer worth of residue, and this
counts down as we approach the end of the buffer, eventually becoming
zero at the end, before returning to the full buffer worth when we
wrap back to the start.
Moving the walking of the descriptors into the interrupt handler means
that we can update the BD_DONE flag at interrupt time, thus avoiding
a delayed tasklet stopping the cyclic DMA.
This means that the residue can be calculated from (total descriptors -
buf_tail) * descriptor size. This is what the change below does. We
update imx-pcm-dma.c to remove the NO_RESIDUE flag since we now provide
the residue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In cyclic dma tx's handler sdma_handle_channel_loop(),
SDMA channel statue is set to either DMA_ERROR or DMA_IN_PROGRESS
based on each period's status. This has the following issues:
1) If one period's status is BD_RROR, then channel status
will be set to DMA_ERROR, but it will be overwritten to DMA_IN_PROGRESS
if the following periods are OK.
2) DMA client may call sdma_control(DMA_TERMINATE_ALL) to stop the cyclic dma
operation, sdma channel status will be set to DMA_ERROR,
but if after this handler is called, then again the channel status will be overwritten
to DMA_IN_PROGRESS. Then the following dmaengine_prep_dma_cyclic() will always fail,
as channel status is DMA_IN_PROGRESS.
As in cyclic dma tx, channel status will be initially set to DMA_IN_PROGRESS,
driver only needs to change it to DMA_ERROR, when something wrong happens
(one period status is wrong, or stoped by client explicitly).
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the
default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding
documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
i.MX series have inner firmware in its ROM code: when SDMA isn't provided
any firmware from Kernel or rootfs, the default inner ROM firmware will be
activated. However the current driver doesn't assign any script number to
this situation, and those platform running in this case would be broken.
Thus this patch adds a default script number when no external firmware being
loaded so that people would continue to be able to use basic scripts to run
their platform without any firmware.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
