For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver. This commit adds analogous
support for the SPI driver. Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).
Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
ath.git patches for v5.17. Major changes:
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
We are seeing below error on QCA6390:
...
[70211.671189] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70212.696154] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
[70213.092941] ath11k_pci 0000:72:00.0: failed to parse rx error in wbm_rel ring desc -22
...
The reason is that, with commit 734223d784 ("ath11k: change return
buffer manager for QCA6390"), ath11k expects the return buffer manager
(RBM) field of descriptor configured as HAL_RX_BUF_RBM_SW1_BM when
parsing error frames from WBM2SW3_RELEASE ring. This is a wrong change
cause the RBM field is set as HAL_RX_BUF_RBM_SW3_BM.
The same issue also applies to REO2TCL ring though we have not got any
error reported.
Fix it by changing RBM from HAL_RX_BUF_RBM_SW1_BM to HAL_RX_BUF_RBM_SW3_BM
for these two rings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Fixes: 734223d784 ("ath11k: change return buffer manager for QCA6390")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211222013536.582527-1-quic_bqiang@quicinc.com
Similar to the same bug in ath10k, a napi disable w/out it being enabled
will hang forever. I believe I saw this while trying rmmod after driver
had some failure on startup. Fix it by keeping state on whether napi is
enabled or not.
And, remove un-used napi pointer in ath11k driver base struct.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200903195254.29379-1-greearb@candelatech.com
The strlcpy should not be used because it doesn't limit the source
length. So that it will lead some potential bugs.
But the strscpy doesn't require reading memory from the src string
beyond the specified "count" bytes, and since the return value is
easier to error-check than strlcpy()'s. In addition, the implementation
is robust to the string changing out from underneath it, unlike the
current strlcpy() implementation.
Thus, replace strlcpy with strscpy.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211221070931.725720-1-wangborong@cdjrlc.com
Register cfg80211_sar_capa with type NL80211_SAR_TYPE_POWER and four
frequency ranges for configurations in unit of 0.25 dBm. And handle
callback set_sar_specs.
Originally, TX power has three main parameters, i.e. power base,
power by rate, and power limit. The formula can be simply considered
as TX power = power base + min(power by rate, power limit). With the
support of SAR which can be treated as another power limit, there is
one more parameter for TX power. And the formula will evolve into
TX power = power base + min(power by rate, power limit, power sar).
Besides, debugfs tx_pwr_tbl is also refined to show SAR information.
The following is an example for the difference.
Before supporting SAR,
-----------------------------------
...
path rate pwr base (byr lmt ) rem
A CCK_1M 66(0x42) 78 -12 ( 12 -12) 0
A CCK_2M 66(0x42) 78 -12 ( 8 -12) 0
...
-----------------------------------
After supporting SAR and making some configurations,
-----------------------------------
...
path rate pwr base (byr lmt sar ) rem
A CCK_1M 62(0x3e) 78 -16 ( 12 -12 -16) 0
A CCK_2M 62(0x3e) 78 -16 ( 8 -12 -16) 0
...
-----------------------------------
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211220093656.65312-1-pkshih@realtek.com
Declare this function allows us to use customized scanning policy.
By doing so we can be more time efficient on each scan. In order to
make existing coex mechanism work as usual, firmware notifies driver
on each channel switch event, then decide antenna ownership based on
the current channel/band. Do note that this new mechanism affects
throughput more than the sw_scan we used to have, but the overall
average throughput is not affected since each scan take less time.
Since the firmware size is limited, we only support probe requests
with custom IEs length under 128 bytes for now, if any user space
tools requires more than that, we'll introduce related changes
afterwards. For backward compatibility, we fallback to sw_scan when
using older firmware that does not support this feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221085010.39421-1-pkshih@realtek.com
wlwifi patches for v5.17 v2
* Support for Time-Aware-SAR (TAS) as read from the BIOS;
* Fix scan timeout issue when 6GHz is enabled;
* Work continues for new HW family Bz;
* Support for Optimized Connectivity Experience (OCE) scan;
* A bunch of FW debugging improvements and fixes;
* Fix one 32-bit compilation issue;
* Some RX changes for new HW family
* Some fixes for 6 GHz scan;
* Fix SAR table fixes with newer platforms;
* Fix early restart crash;
* Small fix in the debugging code;
* Add new Killer device IDs;
* Datapath updates for Bz family continues;
* A couple of important fixes in iwlmei;
* Some other small fixes, clean-ups and improvements.
The shared area is a DMA memory allocated in the host and
mapped so that the host and the CSME firmware can
exchange data. It is mapped through a dedicated PCI device
that is driven by the mei bus driver.
The bus driver is in charge of allocating and mapping this
memory. It also needs to configure the CSME firmware with
a specific set of commands, so that the CSME firmware will
know that this memory is meant to be used by its internal
WLAN module.
For this, the CSME firmware first needs to completely
initialize its WLAN module and only then get the mapping
request.
The problem is that the mei bus enumeration completes
before the WLAN is completely ready. This means that
the WLAN module's initialization is racing with iwlmei's
allocation and mapping flow.
Testing showed a problem in resume flows where iwlmei
was too fast and the DMA mapping failed.
Add a delay to avoid this. This is still racy, but our
measurements showed that we have a good margin and we
should now be safe.
Fixes: 2da4366f9e ("iwlwifi: mei: add the driver to allow cooperation with CSME")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211220142940.8b6279e3d0be.I6fe128b0b86149a85535104822c8355b367887c8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the driver is unregistered, CSME will take ownership on the
device. Reflect this in the iwlmei object so that we will remember
to re-ask for ownership when the driver will register again.
Not doing so will cause CSME not to give the host ownership and
we will see the following error message when trying to bring up
the interface:
iwlwifi 0000:a9:00.0: iwl_pcie_prepare_card_hw iwl_trans_prepare_card_hw enter
iwlwifi 0000:a9:00.0: iwl_pcie_set_hw_ready hardware not ready
iwlwifi 0000:a9:00.0: iwl_pcie_set_hw_ready hardware not ready
iwlwifi 0000:a9:00.0: iwl_pcie_prepare_card_hw Couldn't prepare the card but SAP is connected
iwlwifi 0000:a9:00.0: Error while preparing HW: -16
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211220142940.c7bb5b7644df.I48498d9fd6e3959562205af67aa5f1a822eb762d@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If OEM isn't in the allowed list, TAS should be disabled in US/CA.
Currently, if the OEM isn't allowed - we're sending the TAS only
if we are not in US or CA.
But this country check is done before we even know the country
(usually the configuration is ZZ in that stage).
So do the following instead:
1. Check if the current OEM is in the allowed list
2. If not - add US and CA to tas_block_list_array
3. Send the TAS table to FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of a conflict between BIOS version and FW
version of the PPAG table - the values arrive in the FW in the wrong
places. This happens because we're storing the table in different
structures depending on the BIOS version, not on the FW version,
and so the FW doesn't get what it expect to.
Always store the table in a v2 structure (which is a superset
of v1 and v0).
Also store the table in a structured way and in it's own structure,
rather then storing it in the ppag command structure, similarly to
the WRDS, EWRD and WGDS tables.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211219121514.793a509da7bd.Ia176746a28b816b5f788cce9a281139735909e2a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, iwlwifi crashes
when the opmode module cannot be loaded, due to completing
the completion before using drv->dev, which can then already
be freed.
Fix this by removing the (fairly useless) message. Moving the
completion later causes a deadlock instead, so that's not an
option.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20211210091245.289008-2-luca@coelho.fi
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
