The musb_dsps driver is special in that the parent (glue) device's
driver is accessing registers mapped by the child. The clock is however
shared and is managed by the grandparent device.
Since commit 869c597829 ("usb: musb: dsps: add support for suspend and
resume") the dsps driver has been accessing these registers as part of
suspend and resume.
The parent driver obviously cannot runtime resume the child during
system suspend and is currently relying on the fact that the child will
be RPM_ACTIVE throughout suspend. The suspend implementation also makes
sure to check that the child is indeed present (and hence the clock
enabled) before accessing the registers.
Let's add an explicit runtime resume of the glue device itself to enable
the clock before doing the register accesses in case these assumptions ever
change (i.e. if the child is left runtime suspended).
Note that the glue-timer cancellation is moved after the child-presence
check to keep error handling simple. This should be fine as the timer is
not setup until the controller is being registered and at that time
glue->musb and its driver data have already been initialised.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e18 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5d
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f9546 ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5d ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e18 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: stable <stable@vger.kernel.org> # 4.8+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo memory allocation in mode_2_cfg[] doesn't utilize all the 4KB
memory.
Increse some endpoint fifo buffers to fully use all the 4KB memory. Now
we can support more webcam usecases on DA8xx.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple places in usb core or controller driver which returns
-EMSGSIZE when a class driver queueing urb failed, so the "Message too
long" log doesn't help much for understanding the error.
Let the musb driver to specifically print a error message when
musb_urb_enqueue() returns -EMSGSIZE.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print an error message with qh maxpacket size and hb_mult when hwep
allocation failed, so we have a better idea why it is failed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function musb_ep_xfertype_string() to return the ep transfer
type string.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68fe05e2a4 ("usb: musb: fix tx fifo flush handling") drops the
1ms delay trying to solve the long disconnect time issue when
application queued many tx urbs. However, the 1ms delay is needed for
some use cases, for example, without the delay, reconnecting AR9271 WIFI
dongle no longer works if the connection is dropped from the AP.
So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the
long disconnect time problem with a separate patch for
usb_hcd_flush_endpoint().
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable assignment.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the port_window support in DMAengine and the sDMA driver we can
convert the driver to DMAengine.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the DMA TX in a similar way as we do for the RX: in the DMA
completion callback.
Since we are no longer using DMA completion interrupt for the TX we can as
wall keep these interrupts disabled, but keep the handler for debug
purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of requesting the DMA channel in tusb_omap_dma_allocate() do it
when the controller is created and in runtime work from the DMA channel
pool.
This change is needed for the DMAengine conversion of the driver since the
tusb_omap_dma_allocate() is called in interrupt context which might lead
to lock within the DMAengine API when requesting channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the DMA we have ch (channel), dmareq and sync_dev parameters both
within the tusb_omap_dma_ch and tusb_omap_dma struct.
By creating a common struct the code can be simplified when selecting
between the shared or multichannel DMA parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having one musb_ep_select() instead the two calls in if/else is the same
thing, but makes the code a bit simpler to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_request_slave_channel() failed to return a channel,
then the driver will print an error and request to defer probe,
regardless of the cause of the failure.
Defer if the DMA is not ready yet otherwise print an error.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently VBUS is turned off while a usb device is detached, and turned
on again by the polling routine. This short period VBUS loss prevents
usb modem to switch mode.
VBUS should be constantly on for host-only mode, so this changes the
driver to not turn off VBUS for host-only mode.
Fixes: 2f3fd2c5bd ("usb: musb: Prepare dsps glue layer for PM runtime support")
Cc: stable@vger.kernel.org #v4.11
Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.
To fix this issue, only modify the TX or RX part of the register.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe
lock order error") caused a regression where musb keeps trying to
enable host mode with no cable connected. This seems to be caused
by the fact that now phy is enabled earlier, and we are wrongly
trying to force USB host mode on an OTG port. The errors we are
getting are "trying to suspend as a_idle while active".
For ports configured as OTG, we should not need to do anything
to try to force USB host mode on it's OTG port. Trying to force host
mode in this case just seems to completely confuse the musb state
machine.
Let's fix the issue by making musb_host_setup() attempt to force the
mode only if port_mode is configured for host mode.
Fixes: d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe lock order error")
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function is not __init since it can be called for deferred
probing or when unbinding/rebinding the device, and therefore it must
not reference objects in __initdata, as pointed out by this link
time warning:
WARNING: drivers/usb/musb/da8xx.o(.text+0x9d4): Section mismatch in reference from the function da8xx_probe() to the (unknown reference) .init.data:(unknown)
This removes the annotation.
Reported-by: Olof's autobuilder <olof@lixom.net>
Fixes: d6299b6efb ("usb: musb: Add support of CPPI 4.1 DMA controller to DA8xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA may hang up if a teardown is initiated while an endpoint is still
active (Advisory 2.3.27 of DA8xx errata).
To workaround this issue, add a delay before to initiate the teardown.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, only the PIO mode is supported.
This add support of CPPI 4.1 to DA8xx.
As in DA8xx the CPPI 4.1 DMA is a part of the USBSS, create the CPPI 4.1
device as a child of USB.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
[b-liu@ti.com: minor tweak in the commit log]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the DA8xx, USB and CPPI 4.1 are sharing the same interrupt line.
Update the driver to request a shared irq.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DIV_ROUND_UP is bit useful than series of "/" and "%" operations.
Replace "/%" sequence with DIV_ROUND_UP macro.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanly iounmap the pointer in error and exit paths.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d8 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Cc: <stable@vger.kernel.org> #4.1+
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add code comment to make it clear that the fall-through is intentional.
Read the link for more details: https://lkml.org/lkml/2017/2/9/292
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in tusb_omap_dma structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi41_dma_controller structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update cppi41_dma_callback() to detect an aborted transfer.
This was not required before because cppi41_dma_callback() was only
invoked on transfer completion.
In order to make CPPI 4.1 driver more generic, cppi41_dma_callback()
will be invoked after a transfer abort in order to let the MUSB driver
perform some action such as acknowledge the interrupt that may be fired
during a teardown.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the CPPI 4.1 driver is not completely generic and
only works on DSPS. This is because of IRQ management.
Add a callback to dma_controller that could be invoked on DMA completion
to acknowledge the IRQ.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/usb/musb/musb_dsps.c:270:6: warning:
symbol 'dsps_musb_clear_ep_rxintr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for arm
architecture.
File size before: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4141 400 8 4549 11c5 usb/musb/omap2430.o
File size after: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4333 200 8 4541 11bd usb/musb/omap2430.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
[b-liu@ti.com: added omap2430 in commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now configure the PMIC interrupt to provide us VBUS
events. In that case we don't need to constantly poll the
status and can make it optional. This is only wired up
for the mini-B interface on beaglebone.
Note that eventually we should get also the connect status
for the host interface when the am335x internal PM coprocessor
provides us with an IRQ chip. For now, we still need to poll
for the host mode status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PM_SLEEP is disabled, SIMPLE_DEV_PM_OPS does not use
bfin_resume and bfin_suspend even if CONFIG_PM is enabled:
drivers/usb/musb/blackfin.c:602:12: warning: ‘bfin_resume’ defined but
not used [-Wunused-function]
static int bfin_resume(struct device *dev)
^~~~~~~~~~~
drivers/usb/musb/blackfin.c:585:12: warning: ‘bfin_suspend’ defined but
not used [-Wunused-function]
static int bfin_suspend(struct device *dev)
^~~~~~~~~~~~
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However it is better to mark these functions as __maybe_unused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dsps glue uses PLATFORM_DEVID_AUTO when creating the musb-hdrc
platform devices, this causes that the id will change in each system
depending on the order of driver probe, the order of the usb instances
defined in device-tree, or the list of enabled devices which use also
PLATFORM_DEVID_AUTO in kernel config. This id inconsistency causes
trouble in shell scripting or user guide documentation.
So switch it to static id, starting from 0 to the musb instance with
lower MMR offset. This scheme is also aligned to the naming in the SoC.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the musb ug, force_host bit is allowed to be set along with
force_hs or force_fs bit.
It could help to implement forced host mode via testmode on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch just uses the resource-managed extcon API when registering
the extcon notifier.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Use the quirk MUSB_PRESERVE_SESSION to preseve MUSB_DEVCTL during suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the session during
a suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement PM methods specifics for da8xx glue.
The only thing to do is to power off the phy.
As the registers are in retention during suspend,
there is no need to save them.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
