If we do nothing in suspend/resume, some platform PCIe ip-block
can't guarantee the link back to L0 state from sleep, then, when
we read the EP device will hang. Only we send pme turnoff message
in pci controller suspend, and send pme exit message in resume, the
link state will be normal.
When we send pme turnoff message in pci controller suspend, the
links will into l2/l3 ready, then, host cannot communicate with
ep device, but pci-driver will call back EP device to save them
state. So we need to change platform_driver->suspend/resume to
syscore->suspend/resume.
So the new suspend/resume implementation, send pme turnoff message
in suspend, and send pme exit message in resume. And add a PME handler,
to response PME & message interrupt.
Change platform_driver->suspend/resume to syscore->suspend/resume.
pci-driver will call back EP device, to save EP state in
pci_pm_suspend_noirq, so we need to keep the link, until
pci_pm_suspend_noirq finish.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For PEXCSRBAR, bit 3-0 indicate prefetchable and address type.
So when getting base address, these bits should be masked,
otherwise we may get incorrect base address.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are much pci compatible with version on existing platforms.
To stop putting version numbers in device tree later, we add a
generic compatible 'fsl,qoriq-pcie'.
The version number is readable directly from a register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Moved the following functions out of the __init section:
arch/powerpc/sysdev/fsl_pci.c : fsl_add_bridge()
arch/powerpc/sysdev/indirect_pci.c : setup_indirect_pci()
Those are referenced by arch/powerpc/sysdev/fsl_pci.c : fsl_pci_probe() when
compiling for Book E support.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Freescale platform has class code = 0x0b2000, when it boots. This makes
kernel PCI bus code to setup these devices resulting into the following
notice information when trying to enable them:
pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01)
The above information is outputted by judging value of dev->class before
pci_setup_device() function, and the DECLARE_PCI_FIXUP_HEADER quirk runs
after pci_setup_device() function. But the DECLARE_PCI_FIXUP_EARLY quirk
runs before judging value of dev->class and pci_setup_device() function.
So we use the DECLARE_PCI_FIXUP_EARLY macro to fix this issue.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For Freescale powerpc platform, the PCI-e bus number uses the reassign mode
by default. It means the second PCI-e controller's hose->first_busno is the
first controller's last bus number adding 1. For some hotpluged device(or
controlled by FPGA), the device is linked to PCI-e slot at linux runtime.
It needs rescan for the system to add it and driver it to work. It successes
to rescan the device linked to the first PCI-e controller's slot, but fails to
rescan the device linked to the second PCI-e controller's slot. The cause is
that the bus->number is reset to 0, which isn't equal to the hose->first_busno
for the second controller checking PCI-e link. So it doesn't really check the
PCI-e link status, the link status is always no_link. The device won't be
really rescaned. Reset the bus->number to hose->first_busno in the function
fsl_pcie_check_link(), it will do the real checking PCI-e link status for the
second controller, the device will be rescaned.
Signed-off-by: Yuanquan Chen <Yuanquan.Chen@freescale.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This function contains all the stuff we need to check if SWIOTLB
should be enabled or not. So it is more convenient to enable
the SWIOTLB here than later.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The (1ull << mem_log) is never greater than mem unless mem_log++;
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A PCIe erratum of mpc85xx may causes a core hang when a link of PCIe
goes down. when the link goes down, Non-posted transactions issued
via the ATMU requiring completion result in an instruction stall.
At the same time a machine-check exception is generated to the core
to allow further processing by the handler. We implements the handler
which skips the instruction caused the stall.
This patch depends on patch:
powerpc/85xx: Add platform_device declaration to fsl_pci.h
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Liu Shuo <soniccat.liu@gmail.com>
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The following commit caused a fatal oops when booting on mpc83xx with
a non-express PCI bus (regardless of whether a PCI device is present):
commit 50d8f87d2b
Author: Rojhalat Ibrahim <imr@rtschenk.de>
Date: Mon Apr 8 10:15:28 2013 +0200
powerpc/fsl-pci Make PCIe hotplug work with Freescale PCIe controllers
Up to now the PCIe link status on Freescale PCIe controllers was only
checked once at boot time. So hotplug did not work. With this patch the
link status is checked on every config read. PCIe devices not present at
boot time are found after doing 'echo 1 >/sys/bus/pci/rescan'.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes the issue by calling setup_indirect_pci for all device types.
fsl_indirect_read_config is now only used for booke/86xx PCIe controllers.
Reported-by: Michael Guntsche <mike@it-loops.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The PCI core supports an offset per aperture nowadays but our arch
code still has a single offset per host bridge representing the
difference betwen CPU memory addresses and PCI MMIO addresses.
This is a problem as new machines and hypervisor versions are
coming out where the 64-bit windows will have a different offset
(basically mapped 1:1) from the 32-bit windows.
This fixes it by using separate offsets. In the long run, we probably
want to get rid of that intermediary struct pci_controller and have
those directly stored into the pci_host_bridge as they are parsed
but this will be a more invasive change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linux next is currently failing to compile mpc85xx_defconfig with:
arch/powerpc/sysdev/fsl_pci.c:944:2: error: too many arguments to function 'setup_pci_atmu'
This is caused by (from Kumar's next branch):
commit 34642bbb3d
Author: Kumar Gala <galak@kernel.crashing.org>
powerpc/fsl-pci: Keep PCI SoC controller registers in pci_controller
Which changed definition of setup_pci_atmu() but didn't update one of
the callers. Below fixes this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up to now the PCIe link status on Freescale PCIe controllers was only
checked once at boot time. So hotplug did not work. With this patch the
link status is checked on every config read. PCIe devices not present at
boot time are found after doing 'echo 1 >/sys/bus/pci/rescan'.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to keeping the SoC registers that control and config the PCI
controllers on FSL SoCs in the pci_controller struct. This allows us to
not need to ioremap() the registers in multiple different places that
use them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The size might be 64 bit, so use ilog2() instead of __ilog2() or
__ilog2_u64().
ilog2() can select 32bit or 64bit function automatically.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The T4240 utilizes a new PCIe controller block that has some minor
programming model differences from previous versions.
The major one that impacts initialization is how we determine the link
state. On the 3.x controllers we have a memory mapped SoC register
instead of a PCI config register that reports the link state.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pci controller structure has a provision to store the device structure
pointer of the corresponding platform device. Currently this information is
not stored during fsl pci controller initialization. This information is
required while dealing with iommu groups for pci devices connected to the
fsl pci controller. For the case where the pci devices can't be paritioned,
they would fall under the same device group as the pci controller.
This patch stores the platform device information in the pci controller
structure during initialization.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix and/or improve the compatible strings of the PCI device tree nodes for
some Freescale SOCs. This fixes some issues and improves consistency among
the SOCs.
Specifically:
1) The P1022 has a v1 PCIe controller, so the compatible property should just
say "fsl,mpc8548-pcie". U-Boot does not look for "fsl,p1022-pcie", so it
wasn't fixing up the node.
2) The P4080 has a v2.1 PCIe controller, so add that version-specific string
to the device tree. Update the kernel to also look for that string.
Currently, the kernel looks for "fsl,p4080-pcie" specifically, but
eventually that check should be deleted.
3) The P1010 device tree claims compatibility with v2.2 and v2.3, but that's
redundant. No other device tree does this. Remove the v2.2 string.
4) The kernel looks for both "fsl,p1023-pcie" and "fsl,qoriq-pcie-v2.2",
even though the P1023 device trees has always included both strings. Remove
the search for "fsl,p1023-pcie".
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull powerpc update from Benjamin Herrenschmidt:
"The main highlight is probably some base POWER8 support. There's more
to come such as transactional memory support but that will wait for
the next one.
Overall it's pretty quiet, or rather I've been pretty poor at picking
things up from patchwork and reviewing them this time around and Kumar
no better on the FSL side it seems..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (73 commits)
powerpc+of: Rename and fix OF reconfig notifier error inject module
powerpc: mpc5200: Add a3m071 board support
powerpc/512x: don't compile any platform DIU code if the DIU is not enabled
powerpc/mpc52xx: use module_platform_driver macro
powerpc+of: Export of_reconfig_notifier_[register,unregister]
powerpc/dma/raidengine: add raidengine device
powerpc/iommu/fsl: Add PAMU bypass enable register to ccsr_guts struct
powerpc/mpc85xx: Change spin table to cached memory
powerpc/fsl-pci: Add PCI controller ATMU PM support
powerpc/86xx: fsl_pcibios_fixup_bus requires CONFIG_PCI
drivers/virt: the Freescale hypervisor driver doesn't need to check MSR[GS]
powerpc/85xx: p1022ds: Use NULL instead of 0 for pointers
powerpc: Disable relocation on exceptions when kexecing
powerpc: Enable relocation on during exceptions at boot
powerpc: Move get_longbusy_msecs into hvcall.h and remove duplicate function
powerpc: Add wrappers to enable/disable relocation on exceptions
powerpc: Add set_mode hcall
powerpc: Setup relocation on exceptions for bare metal systems
powerpc: Move initial mfspr LPCR out of __init_LPCR
powerpc: Add relocation on exception vector handlers
...
Power supply for PCI controller ATMU registers is off when system go to
deep-sleep state. So ATMU registers should be re-setup during PCI
controllers resume from sleep.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Neither of these should ever be changed once set. Make them const and
fix up the users that try to modify it in-place. In one case
kmalloc+memcpy is replaced with kstrdup() to avoid modifying the string.
Build tested with defconfigs on ARM, PowerPC, Sparc, MIPS, x86 among
others.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Julian Calaby <julian.calaby@gmail.com>
The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, some latest silicons do not support this
functionality. According to PCIE specification, 'Header Type' offset 0x0e
is used to indicate header type, so change code to use 'Header Type' field
to judge PCIE mode. Because FSL PCI controller does not support
'Header Type', patch still uses 'Programming Interface' to identify PCI
mode.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the following warning:
arch/powerpc/sysdev/fsl_pci.c: In function 'fsl_pci_probe':
arch/powerpc/sysdev/fsl_pci.c:867:25: error: unused variable 'hose'
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We unified the Freescale pci/pcie initialization by changing the fsl_pci
to a platform driver. In previous PCI code architecture the initialization
routine is called at board_setup_arch stage. Now the initialization is done
in probe function which is architectural better. Also It's convenient for
adding PM support for PCI controller in later patch.
Now we registered pci controllers as platform devices. So we combine two
initialization code as one platform driver.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Freescale PCIe IP block revision bigger than rev2.2 will also need
redefine the sequence of inbound windows. So change to use IP block
revision instead of compatible for the judgment.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the dependency on PCI initialization for SWIOTLB initialization.
So that PCI can be initialized at proper time.
SWIOTLB is partly determined by PCI inbound/outbound map which is assigned
in PCI initialization. But swiotlb_init() should be done at the stage of
mem_init() which is much earlier than PCI initialization. So we reserve the
memory for SWIOTLB first and free it if not necessary.
All boards are converted to fit this change.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI controller on the Freescale P5040 is v2.4.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We change fsl_add_bridge to return -ENODEV if the controller is working in
agent mode. Then check the return value of fsl_add_bridge to guarantee
that only successfully added host bus will be scanned.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As an alternative incremental starting point to Jia Hongtao's patchset,
get the FSL PCI init out of the board files, but do not yet convert to a
platform driver.
Rather than having each board supply a magic register offset for
determining the "primary" bus, we look for which PCI host bridge
contains an ISA node within its subtree. If there is no ISA node,
normally that would mean there is no primary bus, but until certain
bugs are fixed we arbitrarily designate a primary in this case.
Conversion to a platform driver and related improvements can happen
after this, as the ordering issues are sorted out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change quirk_fsl_pcie_header from __init to __devinit to ensure if we
have a runtime access (like via an FPGA being loaded after boot on the
PCIe link) that we dont access randomly freed memory.
Signed-off-by: Matias Garcia <mgarcia@rossvideo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Upstream changes to the way PHB resources are registered
broke the resource fixup for FSL boards.
We can no longer rely on the resource pointer array for the PHB's
pci_bus structure, so let's leave it alone and go straight for
the PHB resources instead. This also makes the code generally
more readable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for vmpic-msi nodes to the fsl_msi driver. The MSI is
virtualized by the hypervisor, so the vmpic-msi does not contain a 'reg'
property. Instead, the driver uses hcalls.
Add support for the "msi-address-64" property to the fsl_pci driver.
The Freescale hypervisor typically puts the virtualized MSIIR register
in the page after the end of DDR, so we extend the DDR ATMU to cover it.
Any other location for MSIIR is not supported, for now.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is an issue on FSL-BookE 64-bit devices (P5020) in which PCIe
devices that are capable of doing 64-bit DMAs (like an Intel e1000) do
not function and crash the kernel if we have >4G of memory in the system.
The reason is that the existing code only sets up one inbound window for
access to system memory across PCIe. That window is limited to a 32-bit
address space. So on systems we'll end up utilizing SWIOTLB for dma
mappings. However SWIOTLB dma ops implement dma_alloc_coherent() as
dma_direct_alloc_coherent(). Thus we can end up with dma addresses that
are not accessible because of the inbound window limitation.
We could possibly set the SWIOTLB alloc_coherent op to
swiotlb_alloc_coherent() however that does not address the issue since
the swiotlb_alloc_coherent() will behave almost identical to
dma_direct_alloc_coherent() since the devices coherent_dma_mask will be
greater than any address allocated by swiotlb_alloc_coherent() and thus
we'll never bounce buffer it into a range that would be dma-able.
The easiest and best solution is to just make it so that a 64-bit
capable device is able to DMA to any internal system address.
We accomplish this by opening up a second inbound window that maps all
of memory above the internal SoC address width so we can set it up to
access all of the internal SoC address space if needed.
We than fixup the dma_ops and dma_offset for PCIe devices with a dma
mask greater than the maximum internal SoC address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
This renames pci flags functions and enums in preparation for creating
generic version in asm-generic/pci-bridge.h. The following search and
replace is done:
s/ppc_pci_/pci_/
s/PPC_PCI_/PCI_/
Direct accesses to ppc_pci_flag variable are replaced with helper
functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
FSL PCIe controller can act as agent(EP) or host(RC). Under Agent(EP) mode
the controller will be configured by the host system. So its not required
to be registered with the PCI(e) sub-system. We only register the
controller if its configured in host(RC) mode.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We fixup every FSL PCIe Root Complex we need to fixup a few things.
Rather than adding every device under the sun we move to just matching
only on the vendor (PCI_VENDOR_ID_FREESCALE) and than check that we are
a PCIe controller in host mode in the fixup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PCIe nodes with the property status="disabled" are not usable and so
avoid adding "disabled" PCIe bridge with the system.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller v2.1:
- New MSI inbound window
- Same Inbound windows address as PCIe controller v1.x
Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window
FSL PCIe controller v2.2 and v2.3:
- Different addresses for PCIe inbound window 3,2,1
- Exposed PCIe inbound window 0
- New PCIe interrupt status register
Added new config and interrupt Status register to struct ccsr_pci & updated
pit_t array size to reflect the 4 inbound windows.
Device tree is used to maintain backward compatibility i.e. update inbound
window 1 index depending upon "compatible" field witin PCIE node.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following commit broke 83xx because it assumed the 83xx platforms
exposed the "IMMR" address in BAR0 like the 85xx/86xx/QoriQ devices do:
commit 3da34aae03
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue May 12 15:51:56 2009 -0500
powerpc/fsl: Support unique MSI addresses per PCIe Root Complex
However that is not true, so we have to search through the inbound
window settings on 83xx to find which one matches the IMMR address to
determine its PCI address.
Reported-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed for proper PCI-E support on P1021 SoCs.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
