Make sure that changing the standard or format is not allowed while
one or more of the video, vbi or mpeg vb2 queues are busy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vb2 framework knows if streaming is in progress, no need to use
a separate field for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The width, height and field values are core fields since both vbi, video
and blackbird use the same video input.
Move those fields to the correct struct.
Also fix the field checks in the try_fmt functions: add V4L2_FIELD_SEQ_BT/TB
support and map incorrect field values to a correct field value instead of
returning an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The timeout is way too small. Especially complicated command like
CX2341X_ENC_STOP_CAPTURE takes much more time than 10 ms. Increase the
timeout to 1 second, just as ivtv does (the cx88-blackbird has the
same IP core for MPEG compression as ivtv).
This solves a nasty issue where STOP_CAPTURE would timeout and the
mailbox is left in a busy state, making it impossible to start streaming
a second time without reloading the driver first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
btcx-risc is for the bt8xx driver and other drivers shouldn't depend
on it. There is no benefit to use that module just to do a
pci_zalloc_consistent.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove this function. This makes all vb2 queues behave the same, which
simplifies comparing the various vb2 queue op implementations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't return -1, return a proper error.
Replace dprintk(0, ...) by pr_err since firmware load errors should just be
reported as an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects blackbird, alsa, core, dvb, vbi and
video the changes are all over.
What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.
Much simpler and more robust.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx88/cx88-mpeg.c: In function 'cx8802_mpeg_irq':
drivers/media/pci/cx88/cx88-mpeg.c:419:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-mpeg.c: In function 'cx8802_irq':
drivers/media/pci/cx88/cx88-mpeg.c:453:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c: In function 'snd_cx88_create':
drivers/media/pci/cx88/cx88-alsa.c:818:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c:837:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c: In function 'cx88_audio_initdev':
drivers/media/pci/cx88/cx88-alsa.c:912:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_mbox_func':
drivers/media/pci/cx88/cx88-blackbird.c:327:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:333:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:360:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_find_mailbox':
drivers/media/pci/cx88/cx88-blackbird.c:421:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_load_firmware':
drivers/media/pci/cx88/cx88-blackbird.c:444:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:451:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:453:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:459:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:466:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:487:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:492:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:503:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_initialize_codec':
drivers/media/pci/cx88/cx88-blackbird.c:560:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:566:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:569:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With a filter function you can control more precisely which controls
are added. This is useful in particular for radio device nodes for
combined TV/Radio cards where you want to show just the radio-specific
controls and not controls like brightness.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
