The logic at em28xx_isoc_dvb_max_packetsize() sucks, at least for newer
the needed packet size. Yet, it is better than nothing.
Rewrite the code in order to change the default to 752 for em2884 and
newer chips and provide a better way to handle per-chipset specifics.
For em2874, the current default should be enough, as the only em2874
board is currently a 1-seg ISDB-T board, so, it needs only a limited
amount of bandwidth.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the driver assumes that all QAM carriers are spaced with
8MHz. This is wrong, and may decrease QoS on Countries like Brazil,
that have DVB-C carriers with 6MHz-spaced.
Fortunately, both ITU-T J-83 and EN 300 429 specifies a way to
associate the symbol rate with the bandwidth needed for it.
For ITU-T J-83 2007 annex A, the maximum symbol rate for 6 MHz is:
6 MHz / 1.15 = 5217391 Bauds
For ITU-T J-83 2007 annex C, the maximum symbol rate for 6 MHz is:
6 MHz / 1.13 = 5309735 Bauds.
As this tuner is currently used only for DRX-K, and it is currently
hard-coded to annex A, I've opted to use the roll-off factor of 0.15,
instead of 0.13.
If we ever support annex C, the better would be to add a DVB S2API
call to allow changing between Annex A and C, and add the 0.13 roll-off
factor to it.
This code is currently being used on other frontends, so I think we
should later add a core function with this code, to warrant that
it will be properly implemented everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My previous commit left the file empty and present in the
Makefile, which is a bit dirty and caused problems with
'make distclean', as pointed out by David Howells.
This hopefully cleans it up the right way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: John Linn <john.linn@xilinx.com>
instead of reading the registers everytime
the current implementation respect the following constrain:
- allow 1 to n soc to be enabled
- allow to have a virtual cpu type and subtype
- always detect the cpu type and subtype and report it
- detect if the soc support is enabled
- prepare for sysfs export support
- drop soc specific code via compiler when the soc not enabled
(via cpu_is_xxx)
Today if we read the exid we will have the same value for 9g35 and 9m11
and we will need to check the cidr too
with the new implementation we just need to check the soc subtype
this will also allow to have specific virtual subtype for rm9200 which the
board will have to specify via at91rm9200_set_type(int) as we have no way to
detect it.
this implementation is inspired by the SH cpu detection support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
they are the same except the default priority
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
n2_crypto: Attach on Niagara-T3.
n2rng: Attach on Niagara-T3.
sparc: Detect and handle UltraSPARC-T3 cpu types.
sparc: Don't do expensive hypervisor PCR write unless necessary.
sparc: Add T3 sun4v cpu type and hypervisor group defines.
sparc: Don't leave sparc_pmu_type NULL on sun4v.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9
gro: Only reset frag0 when skb can be pulled
...
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
ALSA: hda - Fix duplicated DAC assignments for Realtek
ALSA: asihpi - off by one in asihpi_hpi_ioctl()
ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
ALSA: asihpi - bug fix pa use before init.
ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
A small modification was necessary since in the machine description
for 'n2cp' and 'ncp' nodes, there no longer is an 'intr' property.
That's OK because this property was always nothing more than an
array of integers '1' ... 'nr_inos + 1' so we can just compute it
in-place.
Signed-off-by: David S. Miller <davem@davemloft.net>
And stop referring to Victoria Falls, as the attribute we're
talking about is whether the rng is multi-unit capable which
applies to several chip variants now.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add min_timeout (minimum timeout) and max_timeout
values so that the framework can check if the new
timeout value is between the minimum and maximum
timeout values. If both values are 0, then the
framework will leave the check for the watchdog
device driver itself.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for extra ioctl calls by adding a
ioctl watchdog operation. This operation will be
called before we do our own handling of ioctl
commands. This way we can override the internal
ioctl command handling and we can also add
extra ioctl commands. The ioctl watchdog operation
should return the appropriate error codes or
-ENOIOCTLCMD if the ioctl command should be handled
through the internal ioctl handling of the framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for the nowayout feature to the
WatchDog Timer Driver Core framework.
This feature prevents the watchdog timer from being
stopped.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add support for the Magic Close feature to the
WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_SETTIMEOUT and WDIOC_GETTIMEOUT ioctl
functionality to the WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_SETOPTIONS ioctl functionality
to the WatchDog Timer Driver Core framework.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the WDIOC_KEEPALIVE ioctl functionality to the
WatchDog Timer Driver Core framework. Please note that the
WDIOF_KEEPALIVEPING bit has to be set in the watchdog_info
options field.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This part add's the basic ioctl functionality to the
WatchDog Timer Driver Core framework. The supported
ioctl call's are:
WDIOC_GETSUPPORT
WDIOC_GETSTATUS
WDIOC_GETBOOTSTATUS
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The WatchDog Timer Driver Core is a framework
that contains the common code for all watchdog-driver's.
It also introduces a watchdog device structure and the
operations that go with it.
This is the introduction of this framework. This part
supports the minimal watchdog userspace API (or with
other words: the functionality to use /dev/watchdog's
open, release and write functionality as defined in
the simplest watchdog API). Extra functionality will
follow in the next set of patches.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This patch is required to enable hpwdt to work on next generation HP servers
with iLO.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For testing the dt work, define a dt-enabled versatile platform.
This patch adds a new versatile platform for when using the device
tree. Add platform and amba devices are discovered and registered by
parsing the device tree. Clocks and initial io mappings are still
configured statically.
This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
irq_domain_generate_simple() is an easy way to generate an irq translation
domain for simple irq controllers. It assumes a flat 1:1 mapping from
hardware irq number to an offset of the first linux irq number assigned
to the controller
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The A0 revision of this chip is the only device that requires these
features to be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5719 has bug where RDMAs larger than 4k can cause problems. This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped. This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates all code that populates tx BDs into a single
routine. Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches are going to break skb fragments into smaller
sizes. This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.
The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment. Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following patches, unmapping skb fragments will get just as
complicated as mapping them. This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first fragment of an skb should always be greater than 8 bytes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated. To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated. It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches will require the use of an additional flag in the
ring_info structure. The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AX88772B uses only 11 bits of the header for the actual size. The other bits
are used for something else. This causes dmesg full of messages:
asix_rx_fixup() Bad Header Length
This patch trims the check to only 11 bits. I believe on older chips, the
remaining 5 top bits are unused.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to send to correct address this time!
---------- Forwarded Message ----------
Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org
cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not? To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>
I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are. The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...
Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init
Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.
Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.
This was reported and based on work by Takuma Umeya. I also verified
the problem and tested that this fix resolves it.
V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.
I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.
V3: Actually sending the proper patch....
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs. This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path. Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs. A subsequent patch will audit drivers to ensure that the
flag is set properly
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Jiri Pirko <jpirko@redhat.com>
CC: Robert Olsson <robert.olsson@its.uu.se>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
