The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: Alex Gal <a.gal@motsai.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new device IDs and assigning generic function/variable
names instead of using device-id specific names.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.
This fixes this warning:
[ 5.488733] ath: phy0: ASPM enabled: 0x43
[ 5.488735] ath: EEPROM regdomain: 0x0
[ 5.488736] ath: EEPROM indicates default country code should be used
[ 5.488736] ath: doing EEPROM country->regdmn map search
[ 5.488737] ath: country maps to regdmn code: 0x3a
[ 5.488737] ath: Country alpha2 being used: US
[ 5.488738] ath: Regpair used: 0x3a
[ 5.488738] ------------[ cut here ]------------
[ 5.488745] WARNING: CPU: 0 PID: 161 at
/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[ 5.488746] wiphy should have REGULATORY_CUSTOM_REG
The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GRO layer has a limit of 8 flows being held in GRO list,
for performance reason.
When a packet comes for a flow not yet in the list,
and list is full, we immediately give it to upper
stacks, lowering aggregation performance.
With TSO auto sizing and FQ packet scheduler, this situation
happens more often.
This patch changes strategy to simply evict the oldest flow of
the list. This works better because of the nature of packet
trains for which GRO is efficient. This also has the effect
of lowering the GRO latency if many flows are competing.
Tested :
Used a 40Gbps NIC, with 4 RX queues, and 200 concurrent TCP_STREAM
netperf.
Before patch, aggregate rate is 11Gbps (while a single flow can reach
30Gbps)
After patch, line rate is reached.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use the native GRO handling of encapsulated protocols on
mlx4, we need to call napi_gro_receive() instead of netif_receive_skb()
unless busy polling is in action.
While we are at it, rename mlx4_en_cq_ll_polling() to
mlx4_en_cq_busy_polling()
Tested with GRE tunnel : GRO aggregation is now performed on the
ethernet device instead of being done later on gre device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
net/ipv4/gre_offload.c:253:5: warning:
symbol 'gre_gro_complete' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
It includes:
* A new NFC driver for Marvell's 8897, and a few NCI fixes and
improvements needed to support this chipset.
* An LLCP fix for how we were setting the default MIU on a p2p link. If
there is no explicit MIU extension announced at connection time, we
must use the default one and not the one announced at LLCP link
establishement time.
* A pn544 EEPROM config update. Some of the currently EEPROM configured
values are overwriting the firmware ones while other should not be set
by the driver itself.
* Some NFC digital stack fixes and improvements. Asynchronous functions
are better documented, RF technologies and CRC functions are set upon
PSL_REQ reception, and a few minor bugs are fixed.
* Minor and miscelaneous pn533, mei_phy and port100 fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=ydBy
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC pull request for 3.14
It includes:
* A new NFC driver for Marvell's 8897, and a few NCI fixes and
improvements needed to support this chipset.
* An LLCP fix for how we were setting the default MIU on a p2p link. If
there is no explicit MIU extension announced at connection time, we
must use the default one and not the one announced at LLCP link
establishement time.
* A pn544 EEPROM config update. Some of the currently EEPROM configured
values are overwriting the firmware ones while other should not be set
by the driver itself.
* Some NFC digital stack fixes and improvements. Asynchronous functions
are better documented, RF technologies and CRC functions are set upon
PSL_REQ reception, and a few minor bugs are fixed.
* Minor and miscelaneous pn533, mei_phy and port100 fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hannes Frederic Sowa says:
====================
path mtu hardening patches
After a lot of back and forth I want to propose these changes regarding
path mtu hardening and give an outline why I think this is the best way
how to proceed:
This set contains the following patches:
* ipv4: introduce ip_dst_mtu_maybe_forward and protect forwarding path against pmtu spoofing
* ipv6: introduce ip6_dst_mtu_forward and protect forwarding path with it
* ipv4: introduce hardened ip_no_pmtu_disc mode
The first one switches the forwarding path of IPv4 to use the interface
mtu by default and ignore a possible discovered path mtu. It provides
a sysctl to switch back to the original behavior (see discussion below).
The second patch does the same thing unconditionally for IPv6. I don't
provide a knob for IPv6 to switch to original behavior (please see
below).
The third patch introduces a hardened pmtu mode, where only pmtu
information are accepted where the protocol is able to do more stringent
checks on the icmp piggyback payload (please see the patch commit msg
for further details).
Why is this change necessary?
First of all, RFC 1191 4. Router specification says:
"When a router is unable to forward a datagram because it exceeds the
MTU of the next-hop network and its Don't Fragment bit is set, the
router is required to return an ICMP Destination Unreachable message
to the source of the datagram, with the Code indicating
"fragmentation needed and DF set". ..."
For some time now fragmentation has been considered problematic, e.g.:
* http://www.hpl.hp.com/techreports/Compaq-DEC/WRL-87-3.pdf
* http://tools.ietf.org/search/rfc4963
Most of them seem to agree that fragmentation should be avoided because
of efficiency, data corruption or security concerns.
Recently it was shown possible that correctly guessing IP ids could lead
to data injection on DNS packets:
<https://sites.google.com/site/hayashulman/files/fragmentation-poisoning.pdf>
While we can try to completly stop fragmentation on the end host
(this is e.g. implemented via IP_PMTUDISC_INTERFACE), we cannot stop
fragmentation completly on the forwarding path. On the end host the
application has to deal with MTUs and has to choose fallback methods
if fragmentation could be an attack vector. This is already the case for
most DNS software, where a maximum UDP packet size can be configured. But
until recently they had no control over local fragmentation and could
thus emit fragmented packets.
On the forwarding path we can just try to delay the fragmentation to
the last hop where this is really necessary. Current kernel already does
that but only because routers don't receive feedback of path mtus, these are
only send back to the end host system. But it is possible to maliciously
insert path mtu inforamtion via ICMP packets which have an icmp echo_reply
payload, because we cannot validate those notifications against local
sockets. DHCP clients which establish an any-bound RAW-socket could also
start processing unwanted fragmentation-needed packets.
Why does IPv4 has a knob to revert to old behavior while IPv6 doesn't?
IPv4 does fragmentation on the path while IPv6 does always respond with
packet-too-big errors. The interface MTU will always be greater than
the path MTU information. So we would discard packets we could actually
forward because of malicious information. After this change we would
let the hop, which really could not forward the packet, notify the host
of this problem.
IPv4 allowes fragmentation mid-path. In case someone does use a software
which tries to discover such paths and assumes that the kernel is handling
the discovered pmtu information automatically. This should be an extremly
rare case, but because I could not exclude the possibility this knob is
provided. Also this software could insert non-locked mtu information
into the kernel. We cannot distinguish that from path mtu information
currently. Premature fragmentation could solve some problems in wrongly
configured networks, thus this switch is provided.
One frag-needed packet could reduce the path mtu down to 522 bytes
(route/min_pmtu).
Misc:
IPv6 neighbor discovery could advertise mtu information for an
interface. These information update the ipv6-specific interface mtu and
thus get used by the forwarding path.
Tunnel and xfrm output path will still honour path mtu and also respond
with Packet-too-Big or fragmentation-needed errors if needed.
Changelog for all patches:
v2)
* enabled ip_forward_use_pmtu by default
* reworded
v3)
* disabled ip_forward_use_pmtu by default
* reworded
v4)
* renamed ip_dst_mtu_secure to ip_dst_mtu_maybe_forward
* updated changelog accordingly
* removed unneeded !!(... & ...) double negations
v2)
* by default we honour pmtu information
3)
* only honor interface mtu
* rewritten and simplified
* no knob to fall back to old mode any more
v2)
* reworded Documentation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This new ip_no_pmtu_disc mode only allowes fragmentation-needed errors
to be honored by protocols which do more stringent validation on the
ICMP's packet payload. This knob is useful for people who e.g. want to
run an unmodified DNS server in a namespace where they need to use pmtu
for TCP connections (as they are used for zone transfers or fallback
for requests) but don't want to use possibly spoofed UDP pmtu information.
Currently the whitelisted protocols are TCP, SCTP and DCCP as they check
if the returned packet is in the window or if the association is valid.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the IPv6 forwarding path we are only concerend about the outgoing
interface MTU, but also respect locked MTUs on routes. Tunnel provider
or IPSEC already have to recheck and if needed send PtB notifications
to the sending host in case the data does not fit into the packet with
added headers (we only know the final header sizes there, while also
using path MTU information).
The reason for this change is, that path MTU information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv6 forwarding path to
wrongfully emit Packet-too-Big errors and drop IPv6 packets.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While forwarding we should not use the protocol path mtu to calculate
the mtu for a forwarded packet but instead use the interface mtu.
We mark forwarded skbs in ip_forward with IPSKB_FORWARDED, which was
introduced for multicast forwarding. But as it does not conflict with
our usage in unicast code path it is perfect for reuse.
I moved the functions ip_sk_accept_pmtu, ip_sk_use_pmtu and ip_skb_dst_mtu
along with the new ip_dst_mtu_maybe_forward to net/ip.h to fix circular
dependencies because of IPSKB_FORWARDED.
Because someone might have written a software which does probe
destinations manually and expects the kernel to honour those path mtus
I introduced a new per-namespace "ip_forward_use_pmtu" knob so someone
can disable this new behaviour. We also still use mtus which are locked on a
route for forwarding.
The reason for this change is, that path mtus information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv4 forwarding path to
wrongfully emit fragmentation needed notifications or start to fragment
packets along a path.
Tunnel and ipsec output paths clear IPCB again, thus IPSKB_FORWARDED
won't be set and further fragmentation logic will use the path mtu to
determine the fragmentation size. They also recheck packet size with
help of path mtu discovery and report appropriate errors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to be compatible with the use of "get_time" (i.e. default
time unit in us) in iproute2 patch for HHF as requested by Stephen.
Signed-off-by: Terry Lam <vtlam@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc is a limited resource. Don't use it unnecessarily.
It seems this allocation should work with kcalloc.
Remove unnecessary memset(,0,) of buf as it's completely
overwritten as the previously only unset field in
struct qlcnic_pci_func_cfg is now set to 0.
Use kfree instead of vfree.
Use ETH_ALEN instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know how large "tp->vlan_shift" is but static checkers worry
about shift wrapping bugs here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disassociate in managed mode, we flush the queues
after mac80211 has already removed the station.
During that time, the pointer to ieee80211_sta to the
fw_id_to_mac_id map is -EINVAL. In that case we should not
set the station as being drained when the last Tx of this
station has exited the shared Tx queue since we are
flushing all the queues anyway.
The draining logic is meant to be used in GO / AP mode only.
In GO / AP mode, we set -EBUSY in the fw_id_to_mac_id map.
This is why testing the ieee80211_sta pointer in the
fw_id_to_mac_id map with IS_ERR isn't enough to set the
station as draining, we need to check that it is -EBUSY.
The only impact of the bug was a print:
Drained sta 1, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
If we can't switch to a column because no rates are supported
in that column this led to a state where the search cycle
got stuck and never ended. This in turn also led to aggregation
not being turned on. Fix this by marking a column as
visited if we can't switch to it.
Reported-and-tested-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The power settings need to be updated after a binding flow is done
and before quota calculations. This was missing in the start_ap_ibss()
flow. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The state variable was not set to false in case of a failure to
complete the start_ap_ibss() flow.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull powerpc fix from Ben Herrenschmidt:
"Here's one regression fix for 3.13 that I would appreciate if you
could still pull in. It was an "interesting" one to debug, basically
it's an old bug that got somewhat "exposed" by new code breaking the
boot on PA Semi boards (yes, it does appear that some people are still
using these!)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Check return value of instance-to-package OF call
Pull x86 fixes from Peter Anvin:
"Sorry, meant to push out this batch earlier this weekend"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu, amd: Clear exceptions in AMD FXSAVE workaround
ftrace/x86: Load ftrace_ops in parameter not the variable holding it
On PA-Semi firmware, the instance-to-package callback doesn't seem
to be implemented. We didn't check for error, however, thus
subsequently passed the -1 value returned into stdout_node to
thins like prom_getprop etc...
Thus caused the firmware to load values around 0 (physical) internally
as node structures. It somewhat "worked" as long as we had a NULL in the
right place (address 8) at the beginning of the kernel, we didn't "see"
the bug. But commit 5c0484e25e
"powerpc: Endian safe trampoline" changed the kernel entry point causing
that old bug to now cause a crash early during boot.
This fixes booting on PA-Semi board by properly checking the return
value from instance-to-package.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Olof Johansson <olof@lixom.net>
---
That code has been around for ages without being used.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a huge mess currently, that is really hard to read. This cleanup
doesn't touch the logic at all, it only breaks easy-to-fix long lines and
updates comment styles.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.
This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The crc16 functionality is not used anymore, therefore
we can safely remove the dependency in the Kbuild file.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With unrolling the batadv_header into the respective structures, the
offsetof checks are now useless. Instead, add build checks for all
packet types which go over the wire to avoid problems with wrong sizes
or compatibility issues on some architectures which don't use every day.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Add missing sysfs attributes in the proper section of the README
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Return at the end of void functions is not needed.
Since most of the void functions in the code do not do so,
make all the others consistent by removing the useless
returns. Actually all the functions to be "fixed" are in
network-coding.h only.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Show tables for the multi interface operation. Originator tables
are added per hard interface.
This patch also changes the API by adding the interface to the
bat_orig_print() parameters.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
To show information per interface, add a debugfs hardif structure
similar to the system in sysfs. Hard interface folders will be created
in "$debugfs/batman-adv/". Files are not yet added.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
