BT Coex needs to be updated when the bandwidth is modified
by the AP.
While at it, remove the vif parameter from
bt_coex_vif_change since it was unused.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Until now, after WoWLAN, we weren't able to keep the
connection to the AP because the firmware didn't give
us the right information. Since the firmware API has
been changed to include all the information we need,
change the driver to work with the new API (if it is
available) and program all the relevant information
in mac80211 to keep the connection.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NICs embedded in platforms that have only 16 Tx queues,
this affect the mapping of the Tx queues.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NICs aren't allowed to be powered up at driver load time.
Fix it, and move the external NVM loading from driver load time to
driver up time (parsing the external nvm file remains at driver load time).
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In loose BT Coex scheme, the aggregation size doesn't need to
be limited.
To avoid triggering it, remove a lockdep assertion - we need
to compute the AMPDU size limit from rate control code which
can't take mvm->mutex. This means that there is a race but in
the worst case, we will have a wrong AMPDU size limit which
is not a big issue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In RF KILL the init ucode is running, but don't complete
all its tasks, so we need to run the init ucode again.
Change the flag name to init_ucode_complete, to be more appropriate.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the new API for BT Coex. The full functionality
will be implemented in further patches.
Note: this disables BT Coex for the currently existing
fw (-7 version).
There is also a new command - the channel inhibition command.
This command tells BT what channels to avoid in order to
minimise the interaction between BT and WiFi.
We can tell BT about 2 channels, primary and secondary.
BT will not tune to primary at all and will avoid secondary
as much as possible.
This also means that we need to track vifs that AP / GO.
So rename iwl_mvm_bt_coex_vif_assoc to
iwl_mvm_bt_coex_vif_change to better reflect its real
meaning.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for scheduled scan according to firmware support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use beacon statistics notification handler
to notify bt coex about rssi changes.
Mac80211's mechanism is not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option to set rx antennas for the scan command from debugfs.
Create a file called ant_rxchain in the mvm debugfs directory.
To choose antennas, write a number between 1-7 to ant_rxchain.
Write 1 for A, 2 for B, 3 for AB and so on.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing, implement setting continuous NoA duration
using a new MVM-specific testmode command.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Performance Based Window snooze mechanism is based on uAPSD and is
used in low-medium traffic scenarios, in order to provide better power
performance while insuring low latency and jitter for the incoming traffic.
This patch enables PBW snoozing in case uAPSD is enabled and all ACs are
uAPSD trigger and delivery enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use beacon statistics notification to track RSSI.
Notify mac80211 when the tresholds are crossed.
The roaming treshold is configured to be
equal to cqm_thold. If the beacon filtering command
is not supported by fw fall back and use mac80211
mechanism.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement basic uAPSD client support adding the following:
- Advertise uAPSD support in HW capabilities
- Set all ACs trigger- and delivery-enabled
- Set max SP length to 2 buffered frames
- Assign QNDP with the highest TID with no mandatory admission
control required
- Set uAPSD related parameters in Power Table command
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs entry for the RX statistics received from
the firmware.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If fw_restart is disabled, using the fw_restart debugfs
file will enable fw_restart and then send the failing
command, but this still frequently fails restart because
it resets fw_restart afterwards and is thus racy.
Fix this by tracking fw_restart separately and allowing
"always restart", "never restart" and "restart N times".
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change beacon filtering command due to a change in the API.
In case the FW supports the old API, we do not send the
BF HCMD and assume that since the corresponding struct in
the FW is zeroed by default then we don't need to disable
it in the FW actively.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To make maintaining some constant default values in the
driver easier, declare them in a separate file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware supports offloading more IPv6 addresses for NDP,
adjust the code to send the correct command depending on the
firmware capability.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change power management implementation to support new host-device API
containing uAPSD parameters. Verify FW support for this new API.
Use the new power table command (0xA9) to configure power management.
Use the legacy command (0x77) if FW does not support the new API.
New file power_legacy.c is introduced for legacy implementation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware / HW can't support more than 16 Rx BA sessions.
Deny any attemps to open more sessions than that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add sram dump on NIC error for debug improvement.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To improve power consumption in idle associated mode FW may lower
RX power. This low linearity mode is acceptable for listening low rate
RX such as beacons and groupcast. The driver enables LPRX only if PM
is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps.
LPRX RSSI threshold is used to limit a range where LPRX is applied.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add prints visible to the user when entering and exiting
thrermal throttling, because so users can tell that the
NIC is getting too hot (and throughput will decrease.)
Signed-off-by: eytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The old nl80211 testmode is no longer useful in iwlwifi,
we're moving towards a new model internally and there's
no open tool to use it, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the D3 firmware crashes, it can be helpful for debugging to
resume the system to get the SRAM snapshot to see why it crashed.
Allow enabling this with a debugfs option.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The AP mode needs to use the MCAST fifo for the MCAST
frames sent after the DTIM. This fifo needs to be
configured with the same parameters as the VOICE FIFO.
A separate SCD queue is mapped to this fifo - the cab_queue
(cab stands for Content After Beacon). This queue isn't
connected to any station, but rather to the MAC context.
This queue should (and is already) be set as the MCAST
queue - this is part of the of MAC context command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge to get the wil6210 changes that a cfg80211 change needs.
A conflict in drivers/net/wireless/ath/ath9k/init.c was just
whitespace changes.
Also fix a semantic conflict due to cw1200 using WoWLAN which
I had modified in my tree.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing the D3 (WoWLAN) firmware, it is useful to be able
to run the firmware with instrumentation while the host isn't
sleeping and can poke at the firmware debug logging etc.
Implement this by a debugfs file. When the file is opened the
D3 firmware is loaded and all regular commands are blocked.
While the file is being read, poll the firmware's PME status
flag and report EOF once it changes to non-zero. When it is
closed, do (most of) the resume processing. This lets a user
just "cat" the file. Pressing Ctrl-C to kill the cat process
will resume the firwmare as though the platform resumed for
non-wireless reason and when the firmware wants to wake up
reading from the file automatically completes.
Unlike in real suspend, only disable interrupts and don't
reset the TX/RX hardware while in the test mode. This is a
workaround for some interrupt problems that happen only when
the PCIe link isn't fully reset (presumably by changing the
PCI config space registers which the core PCI code does.)
Note that while regular operations are blocked from sending
commands to the firmware, they could still be made and cause
strange mac80211 issues. Therefore, while using this testing
feature you need to be careful to not try to disconnect, roam
or similar, and will see warnings for such attempts.
Als note that this requires an upcoming firmware change to
tell the driver the location of the PME status flag in SRAM.
D3 test will fail if the firmware doesn't report the pointer.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware supports periodic keep alive and beacon monitoring,
so advertise connection monitor offload capability by setting
IEEE80211_HW_CONNECTION_MONITOR flag. Implement missed beacons
notification handler. Call ieee80211_beacon_loss in case of
missed beacons, so AP probing by mac80211 can be triggered.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to avoid NIC destruction due to high temperature,
CT kill will power down the NIC.
To avoid this, thermal throttling will decrease throughput
to prevent the NIC from reaching the temperature at which
CT kill is performed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon abort is used by device to increase idle dwell time when system
is idle. This algorithm is on top of beacon filtering feature. Enable
beacon abort only if power management is enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.
Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.
Cc: stable@vger.kernel.org [3.9]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The D3 image SRAM is overwritten by the runtime image, so
it can't be accessed after resume. However, it can be very
useful to look at it to know what happened during D3, so
add the ability to store the image and make it available
in debugfs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In current implementation, the phy context is tightly coupled
with the channel context. This complicates the possibility of
using the same phy context for both netdev interfaces and the P2P
Device interface. To loosen this coupling:
1. Manage all the phy contexts in the mvm op mode, and only save
the phy context id in the chanctx memory.
2. Reference count the phy contexts and free them only when they
are not longer used (both by mac80211 and P2P Device).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function just wraps an existing one, remove it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
